IOP-403 BE-36-1-SS

Looking for a specific replacement part? Ctrl-F (or Command-F for Mac users) brings up your browsers search panel and can search any text on the entire web page. Find parts by searching a part# or part description.

Register your equipment with BHS Optima, BHS's free app.

Single Side Battery Extractor (BE-SS) Parts & Service Manual

TP-625 - SAFETY AND DE-ENERGIZATION PROCEURES

GENERAL SAFETY

• Read and understand all instructions and warnings before using or servicing this equipment.

• Keep these instructions for future reference.

• Battery Extractor (BE) units shall only be operated by suitable persons of at least 18 years of age, who have been trained in the proper and safe operation of the BE and expressly certified/charged, in writing, by the user or their representative.

• Only one person is permitted to travel on the BE at any time.

• BE units shall only be used indoors in an industrial setting on a hard, nonslip, and level floor without defects including but not limited to holes, gouges, cracks, drains or obstacles comprised of concrete or other suitable industrial material meeting the minimum requirements specified by BHS as well as any local requirements.

• A licensed structural engineer should be consulted prior to installing a BE on any building level other than the ground floor.

• BE units are not designed to be shipped or transported after initial delivery.

WORK AREA

• Keep work area clean and well lit. Cluttered work areas and poor lighting can lead to accidents.
• Clean up/contain any fluid spills immediately to prevent slips or falls.
• Be aware of potential hazards when performing any service or maintenance to the unit.

SERVICE & MAINTENANCE

Service personnel shall wear Personal Protective Equipment (PPE) appropriate for the task being performed.

LOCKOUT/TAGOUT

Lockout/tagout the BE per your corporate policy, if damaged or not functioning properly. Lockout/tagout and de-energize all systems prior to performing any maintenance or service to unit.

LEAD-ACID BATTERIES-EXPLOSION HAZARD

Do not allow open flames or sparks of any kind near a battery. Highly explosive gas is generated when charging a battery that can remain in battery cells for extended periods of time after charging is complete.

• Always wear appropriate PPE including rubber apron, gloves, boots and full face shield when performing service or maintenance to any lead-acid batteries.

• Do not place metal or other conductive objects on top of battery. Arcing may occur causing damage to the battery and/or serious personal injury or death.

• Use only chargers matching the voltage and amperage of the battery being charged. Overcharging a battery can cause damage to the battery, charger and/or serious personal injury or death.

• Turn off charger before disconnecting battery from charger. Arcing between battery and charger connectors can cause damage to the connectors and/or serious personal injury or death.

HYDRAULIC HAZARD

AVOID HIGH PRESSURE FLUIDS-Escaping fluid under pressure can penetrate the skin causing serious injury. Relieve pressure before disconnecting hydraulic lines. Tighten all connections before applying pressure. Keep hands and body away from pin holes which eject fluids under high pressure. Use a piece of cardboard or paper to search for leaks. DO NOT use your hand.

Any fluid injected into the skin under high pressure should be considered a serious medical emergency despite an initial normal appearance of the skin. There will be a delayed onset of pain, and serious tissue damage may occur. Medical attention should be sought immediately.

OPERATIONAL SAFETY

OPERATIONAL SAFETY

• Only personnel trained in the proper and safe operation of BE units may operate or service the BE

• Operators shall wear appropriate PPE suitable for working with industrial lead-acid batteries while operating the BE (see prior page).

• All data plates, warning labels, placards, etc shall be in place and legible at all times. Contact BHS for replacement data plates, warning labels, placards or instructions.

• All users and service personnel shall be familiar with the meaning and risks associated with all data plates, warning labels, etc.

• All operators and service personnel shall be aware of potential crush and shear points while operating or servicing the BE.

• Keep hands and arms out of the battery compartment while operating the BE.

• Remove BE from service if damaged, defective, or operating improperly (or becomes such while operating) until repairs can be made to correct any problem(s).

• All operators shall be aware of the location of the end stops in the travel path to prevent driving the BE into the end stops.

DO’s AND DON’T’s

• DO NOT exceed the maximum capacity of the BE.

• DO NOT modify or fit the BE with attachments without prior, written approval from BHS.

• DO NOT perform any maintenance or service to the BE with a battery loaded on the BE.

• DO NOT allow anyone to ride in or on the BE.

• DO NOT operate the BE with any guard or cover removed unless required for maintenance or repair.

• Disconnect the BE from all power sources before attempting to perform service or maintenance to the unit.

• DO NOT drive the BE into the end stops.

• DO NOT operate the BE if disengaged from the guidance track.

• DO NOT allow a battery to exit the BE when a lift truck or battery stand is not present to accept the battery.

• DO NOT use the BE in a manner for which it is not intended. Some examples of prohibited use are but not limited to:

           >>To transport people 
           >>As a vehicle jack
           >>To lift loads greater than its rated load capacity
           >>Where unintentional movement may exist
           >>Having direct contact with foodstuff
           >>In a potentially explosive atmosphere

DE-ENERGIZATION

1. Fully lower the BE roller bed.1.
Failure to fully lower the roller bed when performing service to the BE could result in injury from the roller bed lowering unexpectedly.
2. Turn key on dashboard to the “OFF” position. See Figure 1.


FIGURE 1

3. To de-energize components external to the electrical enclosure, turn the disconnect switch on the enclosure to the “OFF” position. See Figure 2.
Failure to disconnect electrical power to the BE could result in electrical shock. Serious personal injury or death will occur.


FIGURE 2

4. To de-energize the entire BE, including the electrical enclosure,disconnect power to the BE or shut off the electrical branch circuit breaker.
Failure to disconnect electrical power to the BE could result in electrical shock. Serious personal injury or death will occur.
5. Actuate all hydraulic levers in both directions to release any stored hydraulic pressure. See Figure 3.
Failure to release any stored hydraulic pressure could result in injury from:
• Escaping hydraulic fluid under high pressure (see HYDRAULIC HAZARDS in the GENERAL SAFETY section).
• Unexpected movement of hydraulic components.


FIGURE 3

LABELS & PLACARDS

GENERAL INFORMATION

OPERATING CONTROLS

OPERATOR CONSOLE

NOTE: Safety devices for the machine and the machine operating area shall not be rendered inoperable or misused.

SAFETY FEATURES

Key Switch – Located on the dash (see above). Primary on/off switch to prevent unauthorized personnel from operating the BE.

Emergency Stop – Located on the dash (see above). Will stop all functions immediately, locking all hydraulics in place. To use, press down on the red button.

Foot Switch – Must be depressed to operate the BE. Stepping off the foot switch will stop all functions immediately, locking all hydraulics in place. To resume use, depress the foot switch. (Not shown)

Gate Switch – The gate must be fully closed for the BE to operate. (Not shown)

OPERATION OVERVIEW

• The controls consist of three, manually operated, hydraulic control valves and a selector switch which controls the vacuum cup or magnet.

• All manual valves are moved in the direction of the function travel which it controls with exception of the lift/lower valve, which is pulled toward the operator for “up” and pushed away for “down.”

• In the event of any failure or malfunction, step off the foot switch or press the emergency stop button and all functions will stop immediately, locking all hydraulics in place.

• To ensure smooth operation, all valve movements should be made in a slow, deliberate motion.

OPERATING INSTRUCTIONS

PRE-CHANGE OUT PREPARATION

1. Position the lift truck for change out in the designated change out area.
2. Remove all battery restraints and disconnect the battery cables following the manufacturer's guidelines. (Be sure to position the battery cables so as not to be damaged by the battery during change out.)
3. Board the battery extractor and close the safety gate. (The gate must be fully closed or the unit will not operate.)
4. Depress the foot pedal.
5. Turn the key switch to the “ON” position.
6. Ensure the extractor arm is retracted inside the extractor battery compartment prior to moving the extractor.

DISCHARGED BATTERY REMOVAL

1. Move the extractor left or right to position the center of compartment with the center of the lift truck battery compartment.
2. Align the extractor’s roller compartment height with the lift truck’s battery compartment.
3. Move the extractor arm toward the battery until the vacuum cup/magnet contacts the battery.
DO NOT force the cup/magnet to the battery after initial contact with the battery is made.
4. Energize the vacuum/magnet by turning the selector switch on.
5. Move the extractor arm away from the lift truck back into the battery compartment, removing the discharged battery fully into the extractor compartment.
6. Turn off the vacuum/magnet.

DISCHARGED BATTERY RETURN

1. Move the extractor left or right to position the center of the compartment with center of an empty battery rack compartment.
2. If required, adjust the extractor compartment height to the empty battery compartment.
3. Move the battery fully into the empty battery compartment by moving the extractor arm out.
DO NOT force the cup/magnet into the battery after the battery contacts the backstop.
4. Engage the battery safety stop and connect the battery to the charger as required.

CHARGED BATTERY RETRIEVAL

1. Locate a charged battery for the appropriate type of lift truck being changed.
2. Disconnect the desired battery from its charger and disengage the battery safety stop.
ALWAYS be sure charging has been completed and the charger is not still charging the battery. Dangerous sparking/arcing can occur if the battery is unplugged from the charger while charging.
3. Move the extractor left or right to position the center of compartment with the center of the battery compartment.
4. If required, adjust the extractor compartment height to the battery rack level.
5. Move the extractor arm toward the battery until the vacuum cup/magnet contacts the battery.
DO NOT force the cup/magnet to the battery after initial contact with the battery is made.
6. Energize the vacuum cup/magnet by turning the selector switch on.
7. Move the extractor arm away from the battery rack back into the battery compartment, removing the charged battery fully into the extractor compartment.
8. Turn off the vacuum/magnet.

OPERATING INSTRUCTIONS

CHARGED BATTERY INSTALLATION

1. Drive the extractor back to the lift truck and align the roller compartment containing the charged battery as performed in steps 1 and 2 of ”Discharged Battery Removal”.
2. Move the charged battery toward the lift truck compartment by moving the extractor arm out, verifying precise battery alignment.
Many batteries are a tight fit into the lift truck battery compartments. Care MUST be taken to ensure alignment is precise to avoid damage to the battery, lift truck, and/or battery extractor.
3. Adjust the extractor vertically as well as horizontally, if needed.
4. Fully insert the charged battery into the lift truck.
DO NOT force the cup/magnet into the battery after the battery is fully inserted into the lift truck.
5. Retract the extractor arm into the extractor compartment.
6. Fully lower the extractor. Drive the extractor out of the immediate area.
7. Turn off the key switch, remove the key from the switch and carefully exit the extractor.
8. Secure the newly installed battery in the lift truck and reconnect the battery cables.
9. Return the lift truck to service.
DO NOT drive the BE into the travel path end stops. The end stops are designed to prevent the BE from accidentally traveling beyond its designated travel path. Driving the BE into the end stops will cause the BE to stop suddenly, possibly causing damage to the end stop, the BE and/or personal injury.

MANUAL UNLOADING

Lockout/tagout and de-energize all equipment prior to manually unloading any battery.

In the event of power loss or an operational malfunction of the BE not allowing a battery to be unloaded using normal operating procedures, it is recommended a battery be removed from the BE using certified and approved vertical extraction methods and devices.

Read, understand and observe all safety warnings and procedures related to the vertical extraction device(s) being used.

Should the status of the BE not allow for safe vertical extraction due to position in the battery aisle, only repairs required to safely maneuver the BE to a position allowing for safe vertical extraction should be made. Once any batteries are safely unloaded, any remaining repairs can be made.

Extreme care should be taken when working under or around equipment supporting elevated loads. Unexpected movement of the equipment could cause the load and/or equipment to fall. ALWAYS be sure devices of adequate size and strength are in place to prevent any personnel working under the elevated load from being crushed. Serious personal injury or death will occur.

SPARE PARTS LIST

Refer to the Spare Parts Kit (BE-SPKV-SS or BE-SPKM-SS) at the beginning of Section 9 for the list of items recommended by the factory to have on hand for BE-36-1-SS models to minimize any downtime due to minor breakdown that may occur under normal operating conditions.

Use only BHS approved replacement parts.

BHS recommends that a full maintenance inspection report similar to the one provided be done at least once a month.

Any parts found to be excessively worn or damaged should promptly be replaced unless said parts pose a safety risk to the operator and/or extractor, in which case the unit should be removed from service until the problem(s) are remedied (See Operator’s Daily Checklist.)

PARTS SECTIONS

CHASSIS

CAM FOLLOWERS

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
1	PT0505	CAM ROLLER-2 1/4"			4
2	HW0124	WASHER-SHIM-7/8" I.D. X 1-3/8 O.D" X .075"			AR
3	HW0117	WASHER-LOCK-7/8"			4
4	HW0013	NUT-HEX-7/8-14			4
5	PT0507	BEARING-FLANGED LOAD-3"			4
6	05517060	SHIM-SQUARE-.075"			AR
7	HW0142	WASHER-LOCK-1 1/4"			4
8	HW0141	NUT-HEX-1 1/4-12			4

CROSS BAR

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
1	05615008	BAR-TOP CROSS			1
2	HW0411	BOLT-HHCS-3/8-16 X 4 1/2"			4
3	HW0108	WASHER-FLAT-3/8"-SAE			8
4	HW0107	WASHER-LOCK-3/8"			4
5	HW0005	NUT-HEX-3/8-16			4

OPERATOR CONSOLE & GATE

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
1	05517012-2	COVER-CONSOLE			1
2	HW0301	BOLT-SELF TAP "F"-1/4-20 X 1/2"			4
3	05617032-2	BRACKET-MOUNTING-LOWER			2
4	HW0005	NUT-HEX-3/8-16			10
5	HW0107	WASHER-LOCK-3/8"			10
6	HW0108	WASHER-FLAT-3/8"-SAE			12
7	HW0407	BOLT-HHCS-3/8-16 X 2-3/4"			6
8	HW0402	BOLT-HHCS-3/8-16 X 1"			4
9	05617031-2	BRACKET-MOUNTING-UPPER			2
10	43015004	GATE-OPERATOR			1
11	HW0006	NUT-NILN-3/8-16			1
12	HW0408	BOLT-HHCS-3/8-16 X 3-1/4"			1

OPERATOR PLATFORM

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
1	HW0403	BOLT-HHCS 3/8-16 X 1-1/4"			8
2	HW0108	WASHER-FLAT-3/8"-SAE			16
3	HW0107	WASHER-LOCK-3/8"			8
4	HW0005	NUT-HEX-3/8-16			8

TRACK GUIDANCE

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
1	05615016	GUIDE ARM WELDMENT			2
2	05617047	SUPPORT PLATE			2
3	HW0503	BOLT-HHCS-1/2-13 X 1-1/2"			4
4	HW0112	WASHER-FLAT-1/2"-SAE			8
5	HW0110	WASHER-LOCK-1/2"			4
6	HW0007	NUT-HEX-1/2-13			4
7	PT0510	CAM ROLLER-1 3/4"			4
8	HW0115	WASHER-LOCK-3/4"			4
9	HW0011	NUT-HEX-3/4-16			4

POWER TRANSMISSION

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
1	PT0111	HB50A15 X 5/8" IDLER PITCH PART			2
2	HW0010	NUT-JAM-5/8-11			2
3	HW0114	WASHER-FLAT-5/8"-SAE			A/R
4	HW0603	BOLT-FHSCS-5/8-11 X 2"			2
5	05517033	STOP-EXTRACTOR ARM			2
6	HW0425	BOLT-HHCS-3/8-16 X 1-1/4"		GRADE 8	4
7	HW0107	WASHER-LOCK-3/8"			4
8	PT0402	BEARING-PILLOW BLOCK-1"			4
9	08027002	SHIM-PILLOW BLOCK-14 GA		.075" THICK	AR AR
	08027003	SHIM-PILLOW BLOCK-10 GA		.135" THICK
10	08017021	ROD-THREADED-3/8-16 X 3-1/2"			8
11	HW0108	WASHER-FLAT-3/8"-SAE			8
12	HW0006	NUT-NILN-3/8-16			8
13	PT0107	SPROCKET-5015 X 1"			2
14	00197028	KEY-1/4" X 1-1/4"			3
15	05627001	DRIVE SHAFT			1
16	PT0108	SPROCKET-5024 X 1"			1
17	00158001-24	CHAIN-ROLLER-#50			1
18	PT0102	LINK-CONNECTING-#50			1

ROLLERS

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
1	08282001	ROLLER ASSEMBLY		INCLUDES BEARINGS	6
2	08287001	SHAFT-HEX-.75" X 38"			6
3	HW1058	PIN-HITCH			12

GUARDS

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
1	05615007	DASHBOARD			1
2	05615005-3	GUARD-CHAIN-LHS			1
3	05615005-4	GUARD-CHAIN-RHS			1
4	HW0301	BOLT-SELF-TAP “F”-1/4-20 X 1/2"			10

DRIVE AND IDLER WHEELS

DRIVE WHEEL ASSEMBLY

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
1	05522007	FLOOR DRIVE ASSEMBLY			1
2	HW0502	BOLT-HHCS 1/2-13 X 1-1/4"			4
3	HW0112	WASHER-FLAT-1/2"-SAE			8
4	HW0110	WASHER-LOCK-1/2"			16
5	43715012	FRAME-FLOOR DRIVE			1
6	C0050-1	WHEEL-8" X 3"-POLY	80222001		1
7	43727008	SHAFT-WHEEL	80222001		1
8	43097005	KEY-1/4" X 3"	80222001		1
9	00197028	KEY-1/4" X 1-1/4"	80222001		1
10	PT0406	FLANGE BEARING-4 BOLT-1 3/16"	80222001	ALLOY CASTING	2
11	HW0504	BOLT-HHCS-1/2-13 X 2"			4
12	HW0007	NUT-HEX-1/2-13			12
13	43727007	SPACER-DRIVE WHEEL			4
14	43797001	ROD-THREADED-1/2-13 X 7"			4
15	43726004	COUPLING BODY-TAPER BORE-#50	80222001		2
16	PT0321	CHAIN-COUPLING-#50		INCL. CONNECTING PIN	1
17	43726003	BUSHING-TAPER LOCK-1 3/16"	80222001	† SHAFT SIDE	1
18	43726002	BUSHING-TAPER LOCK-1"		† MOTOR SIDE	1
19	HW0323	BOLT-HHCS-5/16-18 X 1"	80222001		8
20	43727006	PLATE-MOTOR MOUNTING			1
21	HW0402	BOLT-HHCS-3/8-16 X 1"			4
22	HW0107	WASHER-LOCK-3/8"			4
23	HC0120	MOTOR-HYDRAULIC-160CC			1
24	H1544	ADAPTER-#6 JICM X #10 SAEM			2

† REUSE OF BUSHINGS AFTER DISASSEMBLY NOT RECOMMENDED.

IDLER CASTERS

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
1	C0220	CASTER-8" X 3"-POLY			2
	C0080	CASTER-6" X 3"-DUAL FLANGED		FOR UNITS WITH FLAT TRACK	2
2	05517048	SHIM-1/4"			A/R
3	HW0007	NUT-HEX-1/2-13			12
4	HW0110	WASHER-LOCK-1/2"			12
5	HW0112	WASHER-FLAT-1/2"-SAE			24
6	HW0504	BOLT-HHCS-1/2-13 X 2"			12
7	C0220	CASTER-8" X 3"-POLY			1

ELECTRICAL

MOUNTING HARDWARE

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
1	HW0321	BOLT-HHCS-5/16-18 X 1-1/4"			4
2	HW0106	WASHER-FLAT-5/16"-SAE			8
3	HW0105	WASHER-LOCK-5/16"			4
4	HW0004	NUT-HEX-5/16-18			4
5	HW0002	NUT-HEX-1/4-20			4
6	HW0103	WASHER-LOCK-1/4"			4
7	HW0104	WASHER-FLAT-1/4"-SAE			8
8	HW0303	BOLT-HHCS-1/4-20 X 1"			4

OPERATOR CONSOLE

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
1	E1126	SWITCH-SELECTOR-2 POSITION		OFF-ON	1
2	E1006	CONTACT BLOCK-N/O			1
3	E1007	CONTACT BLOCK-N/C			1
4	E1310	SWITCH-EMERGENCY STOP			1
5	E0309	HOUR METER		INCL. MOUNTING HARDWARE	1
6	E1315	PLATE-LEGEND-EMERGENCY STOP			1
7	E0327	SWITCH-KEY		INCL. 2 KEYS	1
8	E0351	KEY-REPLACEMENT SET		INCLUDES 2 KEYS	A/R

GATE SWITCH

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
1	E0301-1	SWITCH-FOOT OPERATED			1
2	E0312	SWITCH-GATE			1
3	HW0307	BOLT-SHCS-1/4-20 X 1"			2
4	E0627	BASE-MOUNTING-TIE WRAP			1
5	E0611	BOX-JUNCTION			1
6	E0612	COVER-BOX-JUNCTION			1
7	E0616	RESTRAINT-1/2"		GRIP SIZE .250" TO .375"	2
8	E0622	RESTRAINT-1/2"		GRIP SIZE .450" TO .560"	1
9	PL0502	GROMMET-3/8" I.D.			1
10	43017041	MOUNT-GATE SWITCH			1
11	HW0307	BOLT-SHCS-1/4-20 X 1"			2
12	HW0103	WASHER-LOCK-1/4”			2
13	HW0104	WASHER-FLAT-1/4-SAE			2

AC POWER STANCHION

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
1	05535001	STANCHION-POWER			1
2	E0630	GRIP-CABLE SUPPORT		GRIP SIZE .500" TO .620"	1
3	E0629	SPRING-SHOCK			1
4	E0612	COVER-JUNCTION BOX		INCLUDED WITH ITEM 1	1
5	E0622	RESTRAINT-1/2"		GRIP SIZE .450" TO .560"	1
6	E0617	LOCKNUT-CONDUIT-1/2"			1
7	E0624	CONNECTOR-1/2"			1
8	E0501	CORD-14-4-SO			7'
9	HW1030	U-BOLT-3/8-16 X 2" X 5"-SQUARE BEND			1
10	HW0005	NUT-HEX-3/8-16			4
11	HW0107	WASHER-LOCK-3/8"			4
12	HW0108	WASHER-FLAT-3/8"-SAE			6
13	05517047	RETAINER-STANCHION			1
14	HW0411	BOLT-HHCS-3/8-16 X 4-1/2"			2

CONTROL PANEL

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
1	X350057	FUSE		4 AMP, CLASS CC, TIME DELAY	2
2	-	SCREW-MOUNTING-SUB PANEL		INCL. WITH ITEM 13	15
3	-	WASHER		INCL. WITH ITEM 13	15
4	E0122-1	BASE-DISCONNECT			1
5	05636004	SHAFT-DISCONNECT			1
6	05638001	TRACK-DISCONNECT			1
7	E0341	GROUND LUG			1
8	05636001	MAGNETIC STARTER			1
9	05636010-1	TRANSFORMER			1
10	05638002	WIREWAY-7 3/8"			1
11	05638003	WIREWAY-7 5/8"			1
12	05638004	WIREWAY-12 3/4"			1
13	05636002	PANEL-COMPONENT MOUNTING			1
14	E1330	END STOP-TERMINAL			4
15	E1020	TERMINAL BLOCK-MEDIUM			8
16	E1040	END TERMINAL-MEDIUM			2
17	05638005	TRACK-MOUNTING-TERMINAL BLOCK			1
18	E0902	FUSE		6 AMP, MIDGET, TIME DELAY	1
19	05636010-2	BLOCK-FUSE TRANSFORMER			1
20	E0613	RESTRAINT-3/4"		GRIP SIZE .500" TO .625"	2
21	E0618	LOCKNUT-CONDUIT-3/4"			2
22	E0608-1	RESTRAINT-1/2"-90 DEG		GRIP SIZE .450" TO .560"	1
23	E0617	LOCKNUT-CONDUIT-1/2"			1
24	E0123-1	HANDLE-DISCONNECT		NOT SHOWN	1

JUNCTION BOX

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
1	05636006	JUNCTION BOX			1
2	HW0301	BOLT-SELF-TAP “F”-1/4-20 X 1/2"			4
3	-	SCREW-MOUNTING-SUB PANEL		INCL. WITH ITEM 1	4
4	E0341	GROUND LUG			1
5	05636005	PANEL-COMPONENT MOUNTING			1
6	E1330	END STOP-TERMINAL			2
7	E1022	TERMINAL BLOCK-SMALL			12
8	E1021	END TERMINAL-SMALL			2
9	05638006	TRACK-MOUNTING TERMINAL BLOCK			1
10	E0616	RESTRAINT-1/2"		GRIP SIZE .250" TO .375"	4
11	E0617	LOCKNUT-CONDUIT-1/2"			5
12	E0623	RESTRAINT-1/2"-90 DEG		GRIP SIZE .250" TO .375"	1
13	E0613	RESTRAINT-3/4"		GRIP SIZE .500" TO .625"	1
14	E0618	LOCKNUT-CONDUIT-3/4"			1
15	E1334	RECEPTACLE-FLANGED-2 POLE		15 AMP	1
16	HW0132	NUT-NILN-#8-32			4
17	HW0130	SCREW-RHMS-#8-32 X 1/2"			4

MAGNET CORDS

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
1	41632003	MAGNET ASSEMBLY			1
2	05636007	CABLE-SUPPLY POWER MAGNET			1
3	E0622	RESTRAINT-1/2"		GRIP SIZE .450" TO .560"	2
4	E0617	LOCKNUT-CONDUIT-1/2"			4
5	05632002	CONTROL BOX-MAGNET			1
6	HW0301	BOLT-SELF-TAP “F”-1/4-20 X 1/2"			4
7	E0608-1	RESTRAINT-1/2"-90 DEG		GRIP SIZE .450" TO .560"	2
8	05637011	CORD-COIIL		14-3 CONDUCTOR SIZE	1
9	E0501	CORD-14-4-SO			A/R
10	E0611	BOX-JUNCTION-4" X 2" X 2"			1
11	E0612	COVER-JUNCTION BOX			1

MAGNET CONTROL BOX

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
REF	05632002	MAGNET CONTROL BOX ASSEMBLY			1
1	E1313	SOCKET-RELAY			1
2	E0331	RELAY-CONTROL			1
3	E1009	BRIDGE RECTIFIER-FULL WAVE			1
4	E0622	RESTRAINT-1/2"		GRIP SIZE .450 TO .560	1
5	E0608-1	RESTRAINT-1/2"-90 DEG		GRIP SIZE .450 TO .560	1
6	E0617	LOCKNUT-CONDUIT-1/2"			2
7	E1020	TERMINAL BLOCK-MEDIUM			6
8	E1040	END TERMNINAL			2
9	E1330	END STOP-TERMINAL			4

MAGNET ASSEMBLY

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
REF	41632003	MAGNET ASSEMBLY		INCLUDES ITEMS 1-16	A/R
1	HW0433	STUD-1/2-13 X 5"	80252006		4
2	HW0007	NUT-HEX-1/2-13	80252006		4
3	HW0112	WASHER-FLAT-1/2"-SAE	80252006		12
4	HW1002	SPRING-1/2"	80252006		12
5	HW0008	NUT-NILN-1/2-13	80252006		4
6	41657003	COVER-PROXIMITY SENSOR HOUSING		FRONT	1
7	HW0138	SCREW-FHSCS-#8-32 X 3/8"			4
8	N/A	GASKET-FRONT		DISCONTINUED	1
9	N/A	GASKET-REAR		DISCONTINUED	1
10	41657002	COVER-PROXIMITY SENSOR HOUSING		REAR	1
11	HW1066	WASHER-LOCK-#6			4
12	HW1065	SCREW-SHCS-#6-32 X 3/8"			4
13	E0337	PILOT LIGHT-RED		110VAC/DC	1
14	E0335	RECEPTACLE-5 PIN MALE		WITH 12" LEAD	1
15	E0617	LOCKNUT-CONDUIT-1/2"			1
16	E0314	PROXIMITY SENSOR			1

ELECTRICAL DIAGRAMS

HYDRAULICS

CONTROL VALVES

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
REF	05542038	EXTRACTOR ARM VALVE ASSEMBLY			1
1	HC0201	MANUAL VALVE		MUST REUSE EXISTING HANDLE	1
2	H1303	ADAPTER-90 DEG-#6 JICM X #8 NPTM			2
3	H0305	ELBOW-STR-90 DEG-#8 NPTM X #6 FNPT			2
4	H1501	ADAPTER-#8 JICM X #6 NPTM			2
REF	05542039	LIFT VALVE ASSEMBLY			1
1	HC0201	MANUAL VALVE		MUST REUSE EXISTING HANDLE	1
2	H1303	ADAPTER-90 DEG-#6 JICM X #8 NPTM			1
3	H0305	ELBOW-STR-90 DEG-#8 NPTM X #6 FNPT			1
4	H1501	ADAPTER-#8 JICM X #6 NPTM			1
5	H1507	ADAPTER-#8 JICM X # 8 NPTM			1
6	H0201	BUSHING-RED-#8 NPTM X #4 FNPT			1
7	H0300	ELBOW-STR-90 DEG-#4 NPT			1
8	HC0218	VALVE-CHECK			1
9	H1504	ADAPTER-#6 JICM X #4 NPTM			1
REF	05542040	DRIVE VALVE ASSEMBLY			1
1	HC0201	MANUAL VALVE		MUST REUSE EXISTING HANDLE	1
2	H1303	ADAPTER-90 DEG-#6 JICM X #8 NPTM			2
3	H0305	ELBOW-STR-90 DEG-#8 NPTM X #6 FNPT			1
4	H1501	ADAPTER-#8 JICM X #6 NPTM			1
5	H1507	ADAPTER-#8 JICM X # 8 NPTM			1

VALVE MOUNTING HARDWARE (NOT SHOWN)

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
REF	HW0322	BOLT-HHCS-5/16-18 X 2"			9
REF	HW0106	WASHER-FLAT-5/16"-SAE			18
REF	HW0105	WASHER-LOCK-5/16"			9
REF	HW0004	NUT-HEX-5/16-18			9

HYDRAULIC HOSES

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
1	-	VALVE ASSEMBLY-EXTRACTOR ARM		SEE SECTION 4.0.1	1
2	-	VALVE ASSEMBLY-LIFT		SEE SECTION 4.0.1	1
3	-	VALVE ASSEMBLY-DRIVE		SEE SECTION 4.0.1	1
4	00142001-4	HOSE-HYDRAULIC-1/4" X 15.25"			1
5	00142001-2	HOSE-HYDRAULIC-1/4" X 13"			1
6	00142002-1	HOSE-HYDRAULIC-3/8" X 12.875"		(Bal. shown in Fig. 4.1.2 - Item 2)	1
7	00142001-6	HOSE-HYDRAULIC-1/4" X 21.5"		(Bal. shown in Fig. 4.1.2 - Item 4)	1
8	00142001-21	HOSE-HYDRAULIC-1/4" X 35.5"		(Bal. shown in Fig. 4.5 - Item 4)	1
9	00142001-23	HOSE-HYDRAULIC-1/4" X 37.5"		(Bal. shown in Fig. 4.5 - Item 3)	1
10	H1565	ADAPTER-45 DEG-#6 JICM X #4 NPTM			1
11	H1504	ADAPTER-#6 JICM X #4 NPTM			1
12	H0100	COUPLING-#4 NPT			2
13	H0021	NUT-BULKHEAD-#6 JIC			2
14	H0020	UNION-BULKHEAD-45 DEG-# JICM			2
15	00142001-11	HOSE-HYDRAULIC-1/4" X 26.5"		(Bal. shown in Fig. 4.1.2 - Item 7)	1
16	00142002-2	HOSE-HYDRAULIC-3/8" X 13.125"			1
17	00142001-2	HOSE-HYDRAULIC-1/4" X 13"		(Bal. shown in Fig. 4.1.2 - Item 8)	2
18	00142002-13	HOSE-HYDRAULIC-3/8" X 35.875"		(Bal. shown in Fig. 4.5 - Item 20)	1

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
1	-	VALVE ASSEMBLY-EXTRACTOR ARM		SEE SECTION 4.0.1	1
2	-	VALVE ASSEMBLY-LIFT		SEE SECTION 4.0.1	1
3	-	VALVE ASSEMBLY-DRIVE		SEE SECTION 4.0.1	1
4	00142001-4	HOSE-HYDRAULIC-1/4" X 15.25"			1
5	00142001-2	HOSE-HYDRAULIC-1/4" X 13"			1
6	00142002-1	HOSE-HYDRAULIC-3/8" X 12.875"		(Bal. shown in Fig. 4.1.2 - Item 2)	1
7	00142001-6	HOSE-HYDRAULIC-1/4" X 21.5"		(Bal. shown in Fig. 4.1.2 - Item 4)	1
8	00142001-21	HOSE-HYDRAULIC-1/4" X 35.5"		(Bal. shown in Fig. 4.5 - Item 4)	1
9	00142001-23	HOSE-HYDRAULIC-1/4" X 37.5"		(Bal. shown in Fig. 4.5 - Item 3)	1
10	H1565	ADAPTER-45 DEG-#6 JICM X #4 NPTM			1
11	H1504	ADAPTER-#6 JICM X #4 NPTM			1
12	H0100	COUPLING-#4 NPT			2
13	H0021	NUT-BULKHEAD-#6 JIC			2
14	H0020	UNION-BULKHEAD-45 DEG-# JICM			2
15	00142001-11	HOSE-HYDRAULIC-1/4" X 26.5"		(Bal. shown in Fig. 4.1.2 - Item 7)	1
16	00142002-2	HOSE-HYDRAULIC-3/8" X 13.125"			1
17	00142001-2	HOSE-HYDRAULIC-1/4" X 13"		(Bal. shown in Fig. 4.1.2 - Item 8)	2
18	00142002-13	HOSE-HYDRAULIC-3/8" X 35.875"		(Bal. shown in Fig. 4.5 - Item 20)	1

RESERVOIR

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
REF	05642002	RESERVOIR ASSEMBLY		COMPLETE RESERVOIR ASSY	1
1	HC0542	GASKET		SOLD BY LENGTH	A/R
2	HC0340	GAUGE-SIGHT		W/ THERMOMETER	1
3	HC0306	STRAINER-SUCTION			1
4	HC0308	FILLER/BREATHER ASSEMBLY		INCLUDES GASKETS	1
5	HW0209	SCREW-RHMS-10-32 X 1/2"			6
6	BI0104	ELBOW-RED-90 DEG-#16 NPTF X #12 NPTF			1
7	BI0003	NIPPLE-CLOSE-#16			1
8	HW0402	BOLT-HHCS-3/8-16 X 1"			10
9	H0208	PLUG-#12 NPT			1
10	BI0102	ELBOW-90 DEG-#12 NPT			2
11	BI0002	NIPPLE-CLOSE-#12 NPT			2
12	HC0307	RETURN LINE FILTER ASSEMBLY		HOUSING AND FILTER	1
13	HC0317	FILTER-RETURN LINE		REPLACEMENT FILTER	1
14	41247001	MANIFOLD-RETURN LINE			1
15	H1502	ADAPTER-#8 JICM X #12 NPTM			2
16	H1506	ADAPTER-#6 JICM X #6 NPTM			1
17	HC0403-2	PLUG-#6 NPT			1
18	H1507	ADAPTER-#8 JICM X #6 NPTM			1
19	HW0402	BOLT-HHCS-3/8-16 X 1"			4
20	HW0108	WASHER-FLAT-3/8"-SAE			8
21	HW0107	WASHER-LOCK-3/8"			4
22	HW0005	NUT-HEX-3/8-16			4
23	00142003-19	HOSE ASSY-HYDR-1/2"-30.063”		(Bal. shown in Fig. 4.5 - Item 22)	REF
24	00142002-11	HOSE ASSY-HYDR-3/8”-32.875”		(Bal. shown in Fig. 4.5 - Item 21)	REF
25	00142002-19	HOSE ASSY-HYDR-3/8”-54.875”		(Bal. shown in Fig. 4.1.2 - Item 1)	REF
26	00142001-7	HOSE ASSY-HYDR-1/4”-22.5”		(Bal. shown in Fig. 4.2 - Item 5)	REF

LIFT CYLINDER

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
1	HC0403	CYLINDER-LIFT			1
2	00142001-26	HOSE-HYDRAULIC-1/4" X 41.5"		(Bal. shown in Fig. 4.1 - Item 6)	REF
3	00142001-29	HOSE-HYDRAULIC-1/4" X 44.5"		(Bal. shown in Fig. 4.1 - Item 3)	REF
4	00197036	PIN-CYLINDER-LOWER			1
5	HW1058	PIN-HITCH			4
6	00197035	PIN-CYLINDER-UPPER			1
7	H0302	ELBOW-STR-90 DEG-#6 NPT			1
8	HC0426-1	VELOCITY FUSE			1
9	H1578	ADAPTER-#6 JICM X #6 NPTM			1

EXTRACTOR ARM MOTOR

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
1	HC0102	MOTOR-HYDRAULIC-125 CC		(Bal. shown in Fig 5.0, Item 19)	1
2	H1544	ADAPTER-#6 JICM X #10 SAEM			2
3	00142001-23	HOSE-HYDRAULIC-1/4" X 37.5"		(Bal. shown in Fig. 4.1.1 - Item 9)	REF
4	00142001-21	HOSE-HYDRAULIC-1/4" X 35.5"		(Bal. shown in Fig. 4.1.1 - Item 8)	REF
5	PT0106-1	SPROCKET-5012 X 1"			1
6	05045001	MOUNT-MOTOR			1
7	05615015	COVER-SPROCKET			1
8	HW0006	NUT-NILN-3/8-16			6
9	HW0107	WASHER-LOCK-3/8"			2
10	HW0108	WASHER-FLAT-3/8"-SAE			10
11	HW0403	BOLT-HHCS-3/8-16 X 1-1/4"			4
12	HW0406	BOLT-HHCS-3/8-16 X 2-1/2"		FULL THREAD	2

POWER UNIT

<td style="width:135p

ITEM	BHS PART NUMBER	DESCRIPTION	REF. KIT NO.	NOTES	NO. REQ
1	E0002	MOTOR-ELECTRIC-2 HP		USED PRIOR TO 12/17/04	1
	E0023	MOTOR-ELECTRIC-2 HP		USED 12/17/04 - PRESENT	1
2	E0622	RESTRAINT-1/2"		GRIP SIZE .450" TO .560"	1
3	E0617	LOCKNUT-CONDUIT-1/2"			1
4	N/A	ADAPTER		† USED PRIOR TO 12/17/04	1
	HC0352	ADAPTER		USED 12/17/04 - PRESENT	1
5	HC0314	COUPLING BODY-5/8" (MOTOR SIDE)		ALL UNITS	1
6	HC0316	SPIDER-COUPLING INSERT			1
7	05526001	COUPLING BODY-1/2" (PUMP SIDE)		USED PRIOR TO 12/17/04	1
	HC0351	COUPLING BODY-5/8" (PUMP SIDE)		USED 12/17/04 - PRESENT	1
8	HW0402	BOLT-HHCS-3/8-16 X 1"			4
9	HW0107	WASHER-LOCK-3/8"			4
10	N/A	PUMP-GEAR