IOP-080 ATC - Revision history

Bhsadmin: /* FP-C MOUNTING */ (changed FP MOUNTING to Sub-Heading 1 in WYSIWYG editor.

2023-11-22T20:48:54Z

FP-C MOUNTING: (changed FP MOUNTING to Sub-Heading 1 in WYSIWYG editor.

← Older revision		Revision as of 15:48, 22 November 2023
Line 228:		Line 228:
	''<u>NOTE:</u> Minor modiﬁcation of the fork pocket “tongues” may be required to attain full engagement with some pallet trucks.''[[File:IOP-080 (10-23) Page 014 Figure2.png\|none\|thumb\|300x300px\|FIGURE 2]]</li>		''<u>NOTE:</u> Minor modiﬁcation of the fork pocket “tongues” may be required to attain full engagement with some pallet trucks.''[[File:IOP-080 (10-23) Page 014 Figure2.png\|none\|thumb\|300x300px\|FIGURE 2]]</li>
	</ol>		</ol>
	'''FP MOUNTING'''
			=== '''FP MOUNTING''' ===
	<ol>		<ol>
	<li>Lower the lift truck forks to approximately 1/2"-3/4" off the ﬂoor.</li>		<li>Lower the lift truck forks to approximately 1/2"-3/4" off the ﬂoor.</li>

Bhsadmin: /* FP-C MOUNTING */

2023-11-22T20:45:51Z

FP-C MOUNTING

← Older revision		Revision as of 15:45, 22 November 2023
Line 226:		Line 226:
	<li>Lower the pallet truck forks to the fully lowered position.</li>		<li>Lower the pallet truck forks to the fully lowered position.</li>
	<li>Slowly drive the pallet truck into the fork pockets, ensuring full engagement of the fork pocket “tongues” under the pallet truck power head. See Figure 2.		<li>Slowly drive the pallet truck into the fork pockets, ensuring full engagement of the fork pocket “tongues” under the pallet truck power head. See Figure 2.
	''<u>NOTE:</u> Minor modiﬁcation of the fork pocket “tongues” may be required to attain full engagement with some pallet trucks.''[[File:IOP-080 (10-23) Page 014 Figure2.png\|none\|thumb\|300x300px\|FIGURE 2]]'''FP MOUNTING'''		''<u>NOTE:</u> Minor modiﬁcation of the fork pocket “tongues” may be required to attain full engagement with some pallet trucks.''[[File:IOP-080 (10-23) Page 014 Figure2.png\|none\|thumb\|300x300px\|FIGURE 2]]</li>
	~~</li>~~<ol>		</ol>
			'''FP MOUNTING'''
			<ol>
	<li>Lower the lift truck forks to approximately 1/2"-3/4" off the ﬂoor.</li>		<li>Lower the lift truck forks to approximately 1/2"-3/4" off the ﬂoor.</li>
	<li>Position the forks to their widest point that will ﬁt into the fork pockets.</li>		<li>Position the forks to their widest point that will ﬁt into the fork pockets.</li>

Kperrier: period at FP mounting step one

2023-11-22T19:30:27Z

period at FP mounting step one

← Older revision		Revision as of 14:30, 22 November 2023
Line 228:		Line 228:
	''<u>NOTE:</u> Minor modiﬁcation of the fork pocket “tongues” may be required to attain full engagement with some pallet trucks.''[[File:IOP-080 (10-23) Page 014 Figure2.png\|none\|thumb\|300x300px\|FIGURE 2]]'''FP MOUNTING'''		''<u>NOTE:</u> Minor modiﬁcation of the fork pocket “tongues” may be required to attain full engagement with some pallet trucks.''[[File:IOP-080 (10-23) Page 014 Figure2.png\|none\|thumb\|300x300px\|FIGURE 2]]'''FP MOUNTING'''
	</li><ol>		</li><ol>
	<li>Lower the lift truck forks to approximately 1/2"-3/4" off the ﬂoor</li>		<li>Lower the lift truck forks to approximately 1/2"-3/4" off the ﬂoor.</li>
	<li>Position the forks to their widest point that will ﬁt into the fork pockets.</li>		<li>Position the forks to their widest point that will ﬁt into the fork pockets.</li>
	<li>Slowly drive the lift truck into the fork pockets until the forks are fully engaged in the fork pockets.</li>		<li>Slowly drive the lift truck into the fork pockets until the forks are fully engaged in the fork pockets.</li>

Bhsadmin: /* BOLT ON MOUNTING */ reverted back to original

2023-11-22T19:24:10Z

BOLT ON MOUNTING: reverted back to original

← Older revision		Revision as of 14:24, 22 November 2023
Line 219:		Line 219:
	<li>Tighten the lock nuts evenly, ensuring the mounting plate is ﬂ at against the bottom of the fork when ﬁnished.</li>		<li>Tighten the lock nuts evenly, ensuring the mounting plate is ﬂ at against the bottom of the fork when ﬁnished.</li>

	<li>Repeat Steps 5-8 for the opposite mounting plate. ~~[edit]~~</li>		<li>Repeat Steps 5-8 for the opposite mounting plate.</li>
	</ol>		</ol>

Bhsadmin: Added the word [edit] to the end of step 9 of Bolt-On Mounting

2023-11-22T19:19:20Z

Added the word [edit] to the end of step 9 of Bolt-On Mounting

← Older revision		Revision as of 14:19, 22 November 2023
Line 219:		Line 219:
	<li>Tighten the lock nuts evenly, ensuring the mounting plate is ﬂ at against the bottom of the fork when ﬁnished.</li>		<li>Tighten the lock nuts evenly, ensuring the mounting plate is ﬂ at against the bottom of the fork when ﬁnished.</li>

	<li>Repeat Steps 5-8 for the opposite mounting plate.</li>		<li>Repeat Steps 5-8 for the opposite mounting plate. [edit]</li>
	</ol>		</ol>

Kperrier: /* FP-C MOUNTING */

2023-11-22T18:09:59Z

FP-C MOUNTING

← Older revision		Revision as of 13:09, 22 November 2023
Line 247:		Line 247:
	The reservoir should be ﬁlled within 1" of the top of the reservoir with approximately 0.8 Gal / 3.0 L of Chevron hydraulic oil AW ISO 32 or equivalent ISO 32 grade hydraulic oil with anti-wear additives and foam suppressant.		The reservoir should be ﬁlled within 1" of the top of the reservoir with approximately 0.8 Gal / 3.0 L of Chevron hydraulic oil AW ISO 32 or equivalent ISO 32 grade hydraulic oil with anti-wear additives and foam suppressant.

	''NOTE: It is not necessary to bleed the system after ﬁlling the unit.''		''NOTE: It is not necessary to bleed the system after ﬁlling the unit.''

	[[File:IOP-080 ATC (03-29-10) Page 015 Image 0002.jpg\|300px\|none\|caption]]		[[File:IOP-080 ATC (03-29-10) Page 015 Image 0002.jpg\|300px\|none\|caption]]

Kperrier: /* FP-C MOUNTING */

2023-11-22T17:40:45Z

FP-C MOUNTING

Show changes

Kperrier: /* FP-C MOUNTING */

2023-11-22T17:27:15Z

FP-C MOUNTING

← Older revision		Revision as of 12:27, 22 November 2023
Line 227:		Line 227:
	<li>Slowly drive the pallet truck into the fork pockets, ensuring full engagement of the fork pocket “tongues” under the pallet truck power head. See Figure 2.</li>		<li>Slowly drive the pallet truck into the fork pockets, ensuring full engagement of the fork pocket “tongues” under the pallet truck power head. See Figure 2.</li>

	''<u>NOTE:</u> Minor modiﬁcation of the fork pocket “tongues” may be required to attain full engagement with some pallet trucks.''		''<u>NOTE:</u> Minor modiﬁcation of the fork pocket “tongues” may be required to attain full engagement with some pallet trucks.'''''DO NOT use an ATC equipped with the FP-C option with a lift truck. A dangerous load shift can occur when handling a battery which can cause a possible loss of the battery and/or ATC and possible tip-over of the lift truck in which both situations can result in damage to the equipment as well as personal injury or even death.'''

	~~[[File:Warning bhs sign (1).JPG]]~~

	'''DO NOT use an ATC equipped with the FP-C option with a lift truck. A dangerous load shift can occur when handling a battery which can cause a possible loss of the battery and/or ATC and possible tip-over of the lift truck in which both situations can result in damage to the equipment as well as personal injury or even death.'''

	</ol>		</ol>

Kperrier: /* FP-C MOUNTING */

2023-11-22T17:26:14Z

FP-C MOUNTING

← Older revision		Revision as of 12:26, 22 November 2023
Line 227:		Line 227:
	<li>Slowly drive the pallet truck into the fork pockets, ensuring full engagement of the fork pocket “tongues” under the pallet truck power head. See Figure 2.</li>		<li>Slowly drive the pallet truck into the fork pockets, ensuring full engagement of the fork pocket “tongues” under the pallet truck power head. See Figure 2.</li>

	''NOTE: Minor modiﬁcation of the fork pocket “tongues” may be required to attain full engagement with some pallet trucks.''		''<u>NOTE:</u> Minor modiﬁcation of the fork pocket “tongues” may be required to attain full engagement with some pallet trucks.''

	~~[[File:IOP-080 ATC (03-29-10) Page 014 Figure 2.jpg\|300px\|none\|caption]]~~
	~~FIGURE 2~~

	[[File:Warning bhs sign (1).JPG]]		[[File:Warning bhs sign (1).JPG]]

Kperrier: /* BOLT ON MOUNTING */

2023-11-22T17:19:09Z

BOLT ON MOUNTING

← Older revision		Revision as of 12:19, 22 November 2023
Line 205:		Line 205:
	<li>Shim the unit to obtain 1/4"-1/2" rearward pitch.</li>		<li>Shim the unit to obtain 1/4"-1/2" rearward pitch.</li>

	''NOTE: Shim thickness will vary depending upon the amount of fork deﬂection and/or linkage wear of pallet truck load wheels. 1/4"-1/2" rearward pitch should be veriﬁed through the entire lift range of the pallet truck.''		''<u>NOTE:</u> Shim thickness will vary depending upon the amount of fork deﬂection and/or linkage wear of pallet truck load wheels. 1/4"-1/2" rearward pitch should be veriﬁed through the entire lift range of the pallet truck.''

	<li>Tack weld the shim to the unit to prevent it from moving.</li>		<li>Tack weld the shim to the unit to prevent it from moving.</li>
Line 211:		Line 211:
	<li>Locate the supplied mounting plates and hardware.</li>		<li>Locate the supplied mounting plates and hardware.</li>

	<li>Position mounting plate underneath one of the pallet 5. truck forks aligned with the mounting holes in the rear rail of the ATC.</li>		<li>Position mounting plate underneath one of the pallet truck forks aligned with the mounting holes in the rear rail of the ATC.</li>

	<li>Insert the 3/8-16 x 4" mounting bolts through the holes 6. in the mounting plate and into the mounting holes of the unit. See Figure 1.</li>		<li>Insert the 3/8-16 x 4" mounting bolts through the holes in the mounting plate and into the mounting holes of the unit. See Figure 1.</li>

	[[File:IOP-080 ATC (03-29-10) Page 014 Figure 1.jpg\|300px\|none\|~~caption~~]]		[[File:IOP-080 ATC (03-29-10) Page 014 Figure 1.jpg\|300px\|none\|FIGURE 1\|thumb]]<li>Place one supplied ﬂat washer and locking nut on each of the mounting bolts.</li>
	~~FIGURE 1~~

	~~<li>Place one supplied ﬂat washer and locking nut on each of the mounting bolts.</li>~~		<li>Tighten the lock nuts evenly, ensuring the mounting plate is ﬂ at against the bottom of the fork when ﬁnished.</li>

	<li>Tighten the lock nuts evenly, ensuring the mounting 8. plate is ﬂ at against the bottom of the fork when ﬁnished.</li>

	<li>Repeat Steps 5-8 for the opposite mounting plate.</li>		<li>Repeat Steps 5-8 for the opposite mounting plate.</li>
	</ol>		</ol>

	'''FP-C MOUNTING'''		=== '''FP-C MOUNTING''' ===

	<ol>		<ol>
	<li>Lower the pallet truck forks to the fully lowered position.</li>		<li>Lower the pallet truck forks to the fully lowered position.</li>
Line 242:		Line 238:
	</ol>		</ol>

	'''FP MOUNTING'''		=== '''FP MOUNTING''' ===
	<ol>		<ol>
	<li>Lower the lift truck forks to approximately 1/2"-3/4" off the ﬂoor</li>		<li>Lower the lift truck forks to approximately 1/2"-3/4" off the ﬂoor</li>