Battery Handling Systems - User contributions [en]

(BE-TS) Triple Stack Operator Aboard Battery Extractors – Parts & Service Manual (IOP-401)

2026-01-27T13:32:45Z

Mbowen: /* [Discontinued] Helical Actuator */

'''Looking for a specific replacement part?''' Ctrl-F (or Command-F for Mac users) brings up your browsers search panel and can search any text on the entire web page. Find parts by searching a part # or part description.

'''California Residents''': WARNING: This product contains chemicals known to the State of California to cause cancer and/or reproductive harm, and birth defects or other reproductive harm. [https://na.bhs1.com/about-bhs/compliance-statement-for-california-proposition-65/ Learn more here.]
=<big>Preface</big>=
=<big>TP-606 – Safety & De-Energization Procedures</big>=
==<big>General Safety</big>==
{|
|[[File:Read Before Operating Notice.png|alt=Read Before Operating|frameless|120x120px|link=https://tech.bhs1.com/index.php/File:Read_Before_Operating_Notice.png]]
|
*Read and understand all instructions and warnings before using or servicing this equipment.
*Keep these instructions for future reference.
|}
*Battery Extractor (BE) units shall only be operated by suitable persons of at least 18 years of age, who have been trained in the proper and safe operation of the BE and expressly certified/charged, in writing, by the user or their representative.
*Only one person is permitted to travel on the BE at any time.
*BE units shall only be used indoors in an industrial setting on a hard, nonslip, and level floor without defects including but not limited to holes, gouges, cracks, drains or obstacles comprised of concrete or other suitable industrial material meeting the minimum requirements specified by BHS as well as any local requirements.
*A licensed structural engineer should be consulted prior to installing a BE on any building level other than the ground floor.
*BE units are not designed to be shipped or transported after initial delivery.
*Failure to follow these instructions and warnings may result in property damage, personal injury or death.
===<big>Work Area</big>===
*Keep work area clean and well lit. Cluttered work areas and poor lighting can lead to accidents.
*Clean up/contain any fluid spills immediately to prevent slips or falls.
*Be aware of potential hazards when performing any service or maintenance to the unit.
===<big>Service & Maintenance</big>===
Service personnel shall wear Personal Protective Equipment (PPE) appropriate for the task being performed.
{|
|[[File:Electrical Hazard Warning.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Electrical_Hazard_Warning.png]]
[[File:Danger Warning.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Danger_Warning.png|alt=DANGER]]
|
===<big>Lockout/Tagout</big>===
'''Lockout/tagout the BE per your corporate policy, if damaged or not functioning properly. Lockout/tagout and de-energize all systems prior to performing any maintenance or service to unit.'''
|}
{|
|[[File:Warning-Battery-Explosion.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Warning-Battery-Explosion.png]]
[[File:Danger Warning.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Danger_Warning.png|alt=DANGER]]
|
===<big>Lead-Acid Battery Explosion Hazard</big>===
'''DO NOT allow open flames or sparks of any kind near a battery. Highly explosive gas is generated when charging a battery that can remain in battery cells for extended periods of time after charging is complete.'''
*Always wear appropriate PPE including rubber apron, gloves, boots and full face shield when performing service or maintenance to any lead-acid batteries.
*DO NOT place metal or other conductive objects on top of battery. Arcing may occur causing damage to the battery and/or serious personal injury or death.
*Use only chargers matching the voltage and amperage of the battery being charged. Overcharging a battery can cause damage to the battery, charger and/or serious personal injury or death.
*Turn off charger before disconnecting battery from charger. Arcing between battery and charger connectors can cause damage to the connectors and/or serious personal injury or death.
|}
{|
|[[File:Warning-Hydrualic-Hazard.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Warning-Hydrualic-Hazard.png]]
[[File:Warning.png|alt=WARNING|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Warning.png]]
|
===<big>Hydraulic Hazards</big>===
'''AVOID HIGH PRESSURE FLUIDS-Escaping fluid under pressure can penetrate the skin causing serious injury. Relieve pressure before disconnecting hydraulic lines. Tighten all connections before applying pressure. Keep hands and body away from pin holes which eject fluids under high pressure. Use a piece of cardboard or paper to search for leaks. DO NOT use your hand.'''

'''Any fluid injected into the skin under high pressure should be considered a serious medical emergency despite an initial normal appearance of the skin. There will be a delayed onset of pain, and serious tissue damage may occur. Medical attention should be sought immediately.'''
|}
{|
![[File:No Pacemakers Notice.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:No_Pacemakers_Notice.png]][[File:Strong Magnet Field Hazard Warning.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Strong_Magnet_Field_Hazard_Warning.png]]
[[File:Warning.png|alt=WARNING|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Warning.png]]
|
===<big>Electromagnet Hazard</big>===
'''Units equipped with magnetic extraction generate strong magnetic fields. Persons with pacemakers SHOULD''' '''NOT''' '''operate or be in close proximity to equipment during operation.'''

'''Failure to comply with this direction''' '''could result in serious personal injury or death.'''
|}
===<big>Operational Safety</big>===
*Only personnel trained in the proper and safe operation of BE units may operate or service the BE.
*Operators shall wear appropriate PPE suitable for working with industrial lead-acid batteries while operating the BE ''(See [https://tech.bhs1.com/index.php/(BE-TS)_Triple_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-401)#Lead-Acid_Battery_Explosion_Hazard Lead-Acid Battery Explosion Hazard] section).''
*All data plates, warning labels, placards, etc. shall be in place and legible at all times. Contact BHS for re-placement data plates, warning labels, placards or instructions.
*All users and service personnel shall be familiar with the meaning and risks associated with all data plates, warning labels, etc.
*All operators and service personnel shall be aware of potential crush and shear points while operating or servicing the BE.
*Keep hands and arms inside the operator compartment while operating the BE.
*Remove BE from service if damaged, defective, or operating improperly (or becomes such while operating) until repairs can be made to correct any problem(s).
*All operators shall be aware of the location of the end stops in the travel path to prevent driving the BE into the end stops.
===<big>Do's and Don'ts</big>===
*'''DO NOT''' exceed the maximum capacity of the BE.
*'''DO NOT''' modify or fit the BE with attachments without prior, written approval from BHS.
*'''DO NOT''' perform any maintenance or service to the BE with a battery loaded on the BE.
*'''DO NOT''' allow anyone to ride in or on the BE.
*'''DO NOT''' operate the BE with any guard or cover removed unless required for maintenance or repair.
*Disconnect the BE from all power sources before attempting to perform service or maintenance to the unit.
*'''DO NOT''' drive the BE into the end stops.
*'''DO NOT''' operate the BE if disengaged from the guidance track.
*'''DO NOT''' allow a battery to exit the BE when a lift truck or battery stand is not present to accept the battery.
*'''DO NOT''' rotate the arm onto a battery such that any part of the extractor arm, vacuum cup or magnet contacts the top of the battery.
*'''DO NOT''' allow anyone to enter the area under the carriage without the service stands properly installed.
*'''DO NOT''' use the BE in a manner for which it is not intended. Some examples of prohibited use are but not limited to:
**To transport people
**As a vehicle jack
**To lift loads greater than its rated load capacity
**Where unintentional movement may exist
**Having direct contact with foodstuffs
**In a potentially explosive atmosphere
==<big>De-Energization</big>==
1. Fully lower the BE roller bed or position the roller bed on service stands if service requires the bed be raised. See Figures 1 & 2.
{|
|[[File:WARNING-warn.png|alt=WARNING|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:WARNING-warn.png]]
!Failure to properly support the roller bed when performing service under the BE could result in injury from the roller bed lowering unexpectedly.
|}[[File:IOP-400 BE-SL&DS (10-23) Fully Lower BE Roller Bed.png|alt=Fully lowered BE roller bed|none|thumb|FIGURE 1|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_Fully_Lower_BE_Roller_Bed.png]][[File:IOP-400 BE-SL&DS (10-23) BE Roller Bed on Service Stands .png|alt=Raised BE roller bed positioned on service stands|none|thumb|FIGURE 2|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_BE_Roller_Bed_on_Service_Stands_.png]]2. Turn key on dashboard to the “OFF” position. See Figure 3.[[File:IOP-400 BE-SL&DS (10-23) De-Energization Figure 3.png|alt=Key on BE dashboard turned to the “OFF” position.|none|thumb|FIGURE 3|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_De-Energization_Figure_3.png]]3. Disconnect power to the extractor or shut off the electrical branch circuit breaker.
{|
|[[File:Danger Warning.png|alt=DANGER|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Danger_Warning.png]]
|'''Failure to disconnect electrical power to the BE could result in electrical shock. Serious personal injury or death will occur.'''
|}4. Actuate all hydraulic levers in both directions to re-lease any stored hydraulic pressure. See Figure 4.
{|
|[[File:WARNING-warn.png|alt=WARNING|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:WARNING-warn.png]]
|'''Failure to release any stored hydraulic pres-sure could result in injury from:'''
*'''Escaping hydraulic fluid under high pressure (see ''[https://tech.bhs1.com/index.php/(BE-TS)_Triple_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-401)#Hydraulic_Hazards HYDRAULIC HAZARDS]'' in the ''[https://tech.bhs1.com/index.php/(BE-TS)_Triple_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-401)#General_Safety GENERAL SAFETY]'' section).'''
*'''Unexpected movement of hydraulic components.'''
|}[[File:IOP-400 BE-SL&DS (10-23) Actuate all Hydraulic Levers in Both Directions.png|alt=Actuate all hydraulic levers in both directions to release any stored hydraulic pressure.|none|thumb|FIGURE 4|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_Actuate_all_Hydraulic_Levers_in_Both_Directions.png]]
==<big>Labels & Placards</big>==
'''Operators should be familiar with the meaning of the following labels and placards found on the BE to ensure proper and safe operation.'''
{| class="wikitable"
|-
![[File:Read Before Operating Notice.png|alt=Read Before Operating|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:Read_Before_Operating_Notice.png]]
|'''Read and understand instruction manual prior to use.'''
|-
![[File:Lockout-Before-Servicing-Notice.png|alt=Lockout Before Servicing Unit|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:Lockout-Before-Servicing-Notice.png]]
|'''Lockout before servicing.'''
|-
![[File:IOP-400 BE-SL&DS (10-23) Extractor Arm Positioning Arrows.png|alt=BE-SL & BE-DS Extractor Arm Positioning Arrows|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_Extractor_Arm_Positioning_Arrows.png]]
|'''Extractor arm positioning arrows'''
|-
![[File:Do Not Operate Without Guards or Covers Notice.png|alt=DO NOT Operate Without Guards or Covers Notice|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:Do_Not_Operate_Without_Guards_or_Covers_Notice.png]]
|'''DO NOT operate with guards or covers removed'''
|-
![[File:IOP-400 BE-SL&DS (10-23) No Riders Allowed.png|alt=No riders allowed|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_No_Riders_Allowed.png]]
|'''NO riders allowed.'''
|-
![[File:No Pacemakers Notice.png|alt=DO NOT operate by or in close proximity to people with pacemakers.|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:No_Pacemakers_Notice.png]]
|'''DO NOT operate by or in close proximity to people with pacemakers.'''
|-
![[File:Strong Magnet Field Hazard Warning.png|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:Strong_Magnet_Field_Hazard_Warning.png]]
[[File:Warning.png|alt=WARNING|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:Warning.png]]
|'''Strong Magnet Field Hazard'''
*Attraction between magnet and metallic objects can crush.
*Keep unsecured metallic objects away from magnet.
*De-energize and lockout/tagout before servicing.
|-
![[File:Chain Entanglement Hazard Warning.png|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:Chain_Entanglement_Hazard_Warning.png]]
[[File:Warning.png|alt=WARNING|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:Warning.png]]
|'''Chain Entanglement Hazard'''
*Moving chains and sprockets can crush and cut.
*Keep hands and fingers clear. Do not operate with guards removed.
*De-energize and lockout/tagout before servicing.
|-
![[File:Electrical Hazard Warning.png|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:Electrical_Hazard_Warning.png]]
[[File:Danger Warning.png|alt=DANGER|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:Danger_Warning.png]]
|'''Electrical Hazard'''
*Energized components can cause electrical shock.
*De-energize and lockout/tagout before servicing.
|-
![[File:BE-SL and BE-DS Power Off-On.png|alt=BE-SL and BE-DS Power Off-On|frameless|180x180px|link=https://tech.bhs1.com/index.php/File:BE-SL_and_BE-DS_Power_Off-On.png]]
|'''Power Off/On'''
|-
![[File:IOP-400 BE-SL&DS (10-23) Horn Control.png|alt=BE-SL and BE-DS Horn Control |frameless|180x180px|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_Horn_Control.png]]
|'''Horn (If equipped)'''
|-
![[File:IOP-400 BE-SL&DS (10-23) Vacuum Control.png|alt=BE-SL and BE-DS Vacuum Control |frameless|180x180px|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_Vacuum_Control.png]]
|'''Vacuum Off/On (If equipped)'''
|-
![[File:IOP-400 BE-SL&DS (10-23) Magnet Extraction.png|alt=BE-SL and BE-DS Magnet Off/On|frameless|180x180px|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_Magnet_Extraction.png]]
|'''Magnet Off/On (If equipped)'''
|-
![[File:IOP-400 BE-SL&DS (10-23) Powered Roller Cut Off Override.png|alt=BE-SL and BE-DS Powered Roller Cut Off Override|frameless|180x180px|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_Powered_Roller_Cut_Off_Override.png]]
|'''Powered Roller Cutout Override (If equipped)'''
|-
![[File:IOP-400 BE-SL&DS (10-23) Rack-Level-Assist.png|alt=BE-SL and BE-DS Rack Level Assist |frameless|180x180px|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_Rack-Level-Assist.png]]
|'''Rack Level Assist Indicator (If equipped)'''
|}
{| class="wikitable"
! rowspan="3" |[[File:IOP-400_BE-SL&DS_(10-23)_Power_Rollers_and_Arm_Travel.png.png|alt=BE-SL & DS Powered Roller and Arm Travel Controls|frameless|504x504px|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_Power_Rollers_and_Arm_Travel.png.png]]
|'''Far Power Rollers'''
|-
|'''Arm Travel'''
|-
|'''Near Power Rollers'''
|}
{| class="wikitable"
|+''BE-SL & DS UNITS ONLY''
! colspan="3" |[[File:IOP-400 BE-SL&DS (10-23) BE-SL&DS Units Platform Controls.png|alt=BE-SL & DS Specific Controls|frameless|460x460px|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_BE-SL&DS_Units_Platform_Controls.png]]
|-
|Drive Forward/Reverse
|Platform Raise/Lower
|Arm Rotation Near/Far
|}
{| class="wikitable"
|+''BE-TS & QS UNITS ONLY''
![[File:IOP-400 BE-SL&DS (10-23) BE-TS & BE-QS Platform Raise and Lower Controls.png|alt=BE-TS & BE-QS Platform Raise and Lower Controls|frameless|240x240px|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_BE-TS_&_BE-QS_Platform_Raise_and_Lower_Controls.png]]
! colspan="2" |[[File:IOP-400 BE-SL&DS (10-23)BE-TS & BE-QS Specific Controls.png|alt=BE-TS & BE-QS Specific-Controls|frameless|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)BE-TS_&_BE-QS_Specific_Controls.png]]
|-
|Platform Raise/Lower
|Drive Foward/Reverse
|Arm Rotation Near/Far
|}
=<big>General Information</big>=
==<big>Specification Data</big>==
[[File:BE-TS Specification Data.png|alt=IOP-401 BE-TS (10-23) Specification Data|frameless|600x600px]]
{| class="wikitable"
| colspan="2" |
!BE-24-2-TS
!BE-36-2-TS
!BE-42-2-TS
|-
!A
|Overall Length
|156.5"
|180.5"
|192.5"
|-
!B
|Overall Width
|72"
|72"
|72"
|-
!C
|Overall Height (Lowered)
|158.188"
|158.188"
|160.688"
|-
!
|Overall Height (Raised w/ Overhead Guard)
|182.375"
|182.375"
|182.375"
|-
!
|Overall Height (Raised w/ Strobe & Alarm)
|191.75"
|191.75"
|191.75"
|-
!D
|Wheel Base
|98"
|122"
|134"
|-
!E
|Drive Wheel Center line
|51"
|51"
|51"
|-
!F
|Battery Compartment Width
|24"
|36"
|42"
|-
!G
|Ground Clearance
|.625"
|.625"
|.625"
|-
!H
|Minimum Roller Height
|6.5"
|6.5"
|6.5"
|-
!I
|Maximum Roller Height
|96"
|96"
|96"
|-
!J
|Operator Platform Height (Lowered/Raised)
|11" / 103"
|11" / 103"
|11" / 103"
|}

=== UNITS WITH 10 HP POWER UNIT USED PRIOR TO DECEMBER, 2014 ===
{| class="wikitable"
!
!BE-24-2-TS
!BE-36-2-TS
!BE-42-2-TS
|-
|Travel Speed
|0 to 190 ft/min / 0 to 0.97 m/s
|0 to 190 ft/min / 0 to 0.97 m/s
|0 to 190 ft/min / 0 to 0.97 m/s
|-
|Raise - Lower Speed
|0 to 26 ft/min / 0 to 0.13 m/s
|0 to 26 ft/min / 0 to 0.13 m/s
|0 to 26 ft/min / 0 to 0.13 m/s
|-
|Powered Roller Speed
|0 to 37 ft/min / 0 to 0.19 m/s
|0 to 37 ft/min / 0 to 0.19 m/s
|0 to 37 ft/min / 0 to 0.19 m/s
|-
|Arm Traverse Speed
|0 to 20 ft/min / 0 to 0.10 m/s
|0 to 20 ft/min / 0 to 0.10 m/s
|0 to 20 ft/min / 0 to 0.10 m/s
|-
|Arm Rotation Time
|6 s to 8 s
|6 s to 8 s
|6 s to 8 s
|-
|Draw Bar Pull / Vacuum

(12" / 305 mm Round Cup)
|1,000 lb / 454 kg
|1,000 lb / 454 kg
|1,000 lb / 454 kg
|-
|Draw Bar Pull Magnet*
|800 lb to 1,200 lb / 363 to 544 kg
|800 lb to 1,200 lb / 363 to 544 kg
|800 lb to 1,200 lb / 363 to 544 kg
|-
|Vacuum Attach Time
|< 1 s
|< 1 s
|< 1 s
|-
|Vacuum Release Time
|< 1 s
|< 1 s
|< 1 s
|-
|Input Voltage
|480 V / 3 ph / 60Hz
|480 V / 3 ph / 60Hz
|480 V / 3 ph / 60Hz
|-
|AC Current Draw
|16.5 A
|16.5 A
|16.5 A
|-
|Control Circuit Voltage
|120 V ac
|120 V ac
|120 V ac
|-
|Hydraulic Power Unit
|10 hp / 7.46 kW
|10 hp / 7.46 kW
|10 hp / 7.46 kW
|-
|Hydraulic Pump
|16 gal/min / 61 L/min
|16 gal/min / 61 L/min
|16 gal/min / 61 L/min
|-
|Power Unit
|Hydraulic, Variable Displacement
|Hydraulic, Variable Displacement
|Hydraulic, Variable Displacement
|-
|Operating Pressure
|1,500 psi / 103 bar
|1,500 psi / 103 bar
|1,500 psi / 103 bar
|-
|Vacuum Pump
|1/3 hp / 0.25 kW
|1/3 hp / 0.25 kW
|1/3 hp / 0.25 kW
|-
|Vacuum
|21" Hg / 711 mbar
|21" Hg / 711 mbar
|21" Hg / 711 mbar
|-
|Full Load Capacity
|10,000 lb / 4535 kg
|10,000 lb / 4535 kg
|10,000 lb / 4535 kg
|-
|Weight (Empty)
|8,000 lb / 3629 kg
|8,300 lb / 3765 kg
|8,600 lb / 3901 kg
|-
|Total Compartment Rollers / Powered
|11/5
|11/5
|11/5
|-
|Guide Track
|3" x 2.5" Angle

76 mm x 64 mm
|3" x 2.5" Angle

76 mm x 64 mm
|3" x 2.5" Angle

76 mm x 64 mm
|-
|Overall Dimensions (L x W x H)
|156.5" x 72" x 158.188"

3975 mm x 1829 mm x 4018 mm
|180.5" x 72" x 158.188"

4585 mm x 1829 mm x 4018 mm
|192.5" x 72" x 160.688"

4890 mm x 1829 mm x 4081 mm
|-
|Vacuum Arm Reach
|4.5" to 14" / 114 mm to 356 mm
|4.5" to 14" / 114 mm to 356 mm
|4.5" to 14" / 114 mm to 356 mm
|-
|Vacuum Arm Reach (Hydraulic Extension)
|9" to 23" / 229 mm to 584 mm
|9" to 23" / 229 mm to 584 mm
|9" to 23" / 229 mm to 584 mm
|-
|Magnet Arm Reach (Hydraulic Extension) Truck Side
|14" to 22" / 355 mm to 559 mm
|14" to 22" / 355 mm to 559 mm
|14" to 22" / 355 mm to 559 mm
|-
|Wheel Base
|98" / 2489 mm
|122" / 3099 mm
|134" / 3404 mm
|-
|Drive Wheel Center Line
|51" / 1295 mm
|51" / 1295 mm
|51" / 1295 mm
|-
|Battery Compartment Width
|24" / 610 mm
|36" / 915 mm
|42" / 1067 mm
|-
|Maximum Battery Dimensions

(L x W x H)
|48" x 23" x 34"

1219 mm x 584 mm x 864 mm
|48" x 35" x 34"

1219 mm x 889 mm x 864 mm
|48" x 41" x 34"

1219 mm x 1041 mm x 864 mm
|-
|Minimum Battery Width

(with vacuum / magnet)
|12" / 305 mm

6" / 152 mm
|12" / 305 mm

6" / 152 mm
|12" / 305 mm

6" / 152 mm
|-
|Minimum Battery Height
|17.75" / 451 mm
|17.75" / 451 mm
|17.75" / 451 mm
|-
|Ground Clearance
|0.63" / 16 mm
|0.63" / 16 mm
|0.63" / 16 mm
|-
|Roller Height
|6.5" Min / 96" Max

165 mm Min / 2438 mm Max
|6.5" Min / 96" Max

165 mm Min / 2438 mm Max
|6.5" Min / 96" Max

165 mm Min / 2438 mm Max
|-
! colspan="4" |NOTES
|-
| colspan="4" |''Specifications may vary ± 5% because of temperature, floor considerations, and operator efficiency. Values represented under normal operating conditions.''
|-
| colspan="4" |''* Varies with battery case thickness and condition.''
|}

=== UNITS WITH 20 HP POWER UNIT USED DECEMBER, 2014 TO PRESENT ===
{| class="wikitable"
!
!BE-24-2-TS
!BE-36-2-TS
!BE-42-2-TS
|-
|Travel Speed
|0 to 240 ft/min / 0 to 1.22 m/s
|0 to 240 ft/min / 0 to 1.22 m/s
|0 to 240 ft/min / 0 to 1.22 m/s
|-
|Raise - Lower Speed
|0 to 26 ft/min / 0 to 0.13 m/s
|0 to 26 ft/min / 0 to 0.13 m/s
|0 to 26 ft/min / 0 to 0.13 m/s
|-
|Powered Roller Speed
|0 to 37 ft/min / 0 to 0.19 m/s
|0 to 37 ft/min / 0 to 0.19 m/s
|0 to 37 ft/min / 0 to 0.19 m/s
|-
|Arm Traverse Speed
|0 to 20 ft/min / 0 to 0.10 m/s
|0 to 20 ft/min / 0 to 0.10 m/s
|0 to 20 ft/min / 0 to 0.10 m/s
|-
|Arm Rotation Time
|6 s to 8 s
|6 s to 8 s
|6 s to 8 s
|-
|Draw Bar Pull / Vacuum

(12" / 305 mm Round Cup)
|1,000 lb / 454 kg
|1,000 lb / 454 kg
|1,000 lb / 454 kg
|-
|Draw Bar Pull Magnet*
|800 lb to 1,200 lb / 363 to 544 kg
|800 lb to 1,200 lb / 363 to 544 kg
|800 lb to 1,200 lb / 363 to 544 kg
|-
|Vacuum Attach Time
|< 1 s
|< 1 s
|< 1 s
|-
|Vacuum Release Time
|< 1 s
|< 1 s
|< 1 s
|-
|Input Voltage
|480 V / 3 ph / 60Hz
|480 V / 3 ph / 60Hz
|480 V / 3 ph / 60Hz
|-
|AC Current Draw
|35 A
|35 A
|35 A
|-
|AC Current Draw w/ Electric Drive Option
|42 A
|42 A
|42 A
|-
|Control Circuit Voltage
|120 V ac
|120 V ac
|120 V ac
|-
|Hydraulic Power Unit
|20 hp / 14.9 kW
|20 hp / 14.9 kW
|20 hp / 14.9 kW
|-
|Hydraulic Power Unit w/ Electric Drive Option
|25 hp / 18.7 kW
|25 hp / 18.7 kW
|25 hp / 18.7 kW
|-
|Hydraulic Pump
|22 gal/min / 83 L/min
|22 gal/min / 83 L/min
|22 gal/min / 83 L/min
|-
|Power Unit
|Hydraulic, Variable Displacement
|Hydraulic, Variable Displacement
|Hydraulic, Variable Displacement
|-
|Operating Pressure
|1,500 psi / 103 bar
|1,500 psi / 103 bar
|1,500 psi / 103 bar
|-
|Vacuum Pump
|1/3 hp / 0.25 kW
|1/3 hp / 0.25 kW
|1/3 hp / 0.25 kW
|-
|Vacuum
|21" Hg / 711 mbar
|21" Hg / 711 mbar
|21" Hg / 711 mbar
|-
|Full Load Capacity
|10,000 lb / 4535 kg
|10,000 lb / 4535 kg
|10,000 lb / 4535 kg
|-
|Weight (Empty)
|8,000 lb / 3629 kg
|8,300 lb / 3765 kg
|8,600 lb / 3901 kg
|-
|Total Compartment Rollers / Powered
|11/5
|11/5
|11/5
|-
|Guide Track
|3" x 2.5" Angle

76 mm x 64 mm
|3" x 2.5" Angle

76 mm x 64 mm
|3" x 2.5" Angle

76 mm x 64 mm
|-
|Overall Dimensions (L x W x H)
|156.5" x 72" x 158.188"

3975 mm x 1829 mm x 4018 mm
|180.5" x 72" x 158.188"

4585 mm x 1829 mm x 4018 mm
|192.5" x 72" x 160.688"

4890 mm x 1829 mm x 4081 mm
|-
|Vacuum Arm Reach
|4.5" to 14" / 114 mm to 356 mm
|4.5" to 14" / 114 mm to 356 mm
|4.5" to 14" / 114 mm to 356 mm
|-
|Vacuum Arm Reach (Hydraulic Extension)
|9" to 23" / 229 mm to 584 mm
|9" to 23" / 229 mm to 584 mm
|9" to 23" / 229 mm to 584 mm
|-
|Magnet Arm Reach (Hydraulic Extension) Truck Side
|14" to 22" / 355 mm to 559 mm
|14" to 22" / 355 mm to 559 mm
|14" to 22" / 355 mm to 559 mm
|-
|Wheel Base
|98" / 2489 mm
|122" / 3099 mm
|134" / 3404 mm
|-
|Drive Wheel Center Line
|51" / 1295 mm
|51" / 1295 mm
|51" / 1295 mm
|-
|Battery Compartment Width
|24" / 610 mm
|36" / 915 mm
|42" / 1067 mm
|-
|Maximum Battery Dimensions

(L x W x H)
|48" x 23" x 34"

1219 mm x 584 mm x 864 mm
|48" x 35" x 34"

1219 mm x 889 mm x 864 mm
|48" x 41" x 34"

1219 mm x 1041 mm x 864 mm
|-
|Minimum Battery Width

(with vacuum / magnet)
|12" / 305 mm

6" / 152 mm
|12" / 305 mm

6" / 152 mm
|12" / 305 mm

6" / 152 mm
|-
|Minimum Battery Height
|17.75" / 451 mm
|17.75" / 451 mm
|17.75" / 451 mm
|-
|Ground Clearance
|0.63" / 16 mm
|0.63" / 16 mm
|0.63" / 16 mm
|-
|Roller Height
|6.5" Min / 96" Max

165 mm Min / 2438 mm Max
|6.5" Min / 96" Max

165 mm Min / 2438 mm Max
|6.5" Min / 96" Max

165 mm Min / 2438 mm Max
|-
! colspan="4" |NOTES
|-
| colspan="4" |''Specifications may vary ± 5% because of temperature, floor considerations, and operator efficiency. Values represented under normal operating conditions.''
|-
| colspan="4" |''* Varies with battery case thickness and condition.''
|}
==<big>Pre-Installation Check</big>==
===<big>Floor Conditions</big>===
The floor is the single most critical area of the battery room. A bad floor can cause significant issues with the installation as well as downtime and maintenance problems with the extractor. The floor should be verified as to its minimum thickness and strength with user. As noted on the drawing, the specific requirement of flatness for your particular type of system is listed. Below is a chart stating floor requirements. If possible, especially on double stack and higher systems, a digital level should be used to shoot the grade for compliance with the specification. The floor should also be inspected for severe cracks or excessively wide expansion joints in the travel path of the machine. If floor drains are present, they must not have a grade to the opening that encroaches into the travel path.

F-min is a rating method used to evaluate the flatness and levelness of a floor designated as "defined travel path". For example, an F-min rating of 60 means that there is no more than .129" of variation in the transverse axis (wheels left to right) and .287" variation in the longitudinal axis (front to back) on the equipment.

To avoid potential damage to drive wheel assemblies, guide track, structural components, guide rollers and issues with the inner frame equalization the "defined travel path" of the Battery Extractor should meet or exceed the recommended F-min specification. See chart below for the model specifications.
{| class="wikitable"
!Model
!F-Min
!+/- Longitudinal
!+/- Transverse
!Slope Defect
|-
|SL, DS
|40
|.287"
|.192"
|.096"
|-
|TS
|60
|.186"
|.129"
|.066"
|-
|QS
|85
|.131"
|.091"
|.047"
|}[[File:IOP-400 BE-SL&DS (10-23) Floor Conditions Pre-Installation Check.png|alt=BE-TS Floor Conditions Pre-Installation Check|frameless|500x500px|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_Floor_Conditions_Pre-Installation_Check.png]]
==<big>Operating Controls & Instructions</big>==

=== <big>Operator Console</big> ===
[[File:BE-TS Operator Console.png|alt=BE-TS Operator Console|frameless|1080x1080px]]

'''''NOTE:''' Safety devices for the machine and the machine operating area SHALL NOT be rendered inoperable or misused.''

''Typical BE-TS operator console shown above. Position of optional controls may vary from that shown depending on age of unit and/or combination of optional controls present.''

''HMI display standard on units shipped after February, 2020 for Industrial Internet of Things (IIoT) package.''

==== <big>Safety Features</big> ====
Key Switch – Located on the dash (see above). Primary on/off switch to prevent unauthorized personnel from operating the BE.

Emergency Stop – Located on the dash (see above). Will stop all functions immediately, locking all hydraulics in place. To use, press down on the red button. The machine key must be used to reset the emergency stop.

Foot Switch – Must be depressed to operate the BE. Stepping off the foot switch will stop all functions immediately, locking all hydraulics in place. To resume use, depress the foot switch.

Gate Switch – The gate must be fully closed for the BE to operate.

Extractor Arm Switch – Does not permit the machine to move forward or backward unless the extractor arm is located in the center of the carriage between the indicating arrows located on the arm guard.

Powered Roller Cutout (PRC-1 or PRC-2) ''(if equipped)'' – Disengages the powered roller function when the photo eye positioned on the edge of the BE battery compartment is disrupted by a battery, requiring additional input from the operator. Pressing the "Power Roller Cutout" override button (see above) on the dash will resume powered roller operation when loading or unloading batteries from the BE carriage.

Horn ''(If equipped)'' – Button located on the dash (see above). Used to alert personnel before moving the BE.

Strobe Light ''(If equipped)'' – Located on a vertical stanchion mounted to the right rear of the operator compartment. For units equipped with optional overhead guard (OHG), the beacon is located above of the operator compartment. Beacon automatically flashes when the BE is switched on to visually notify the BE is in use.

Audible Alarm ''(if equipped)'' – Mounted in the same location as the Strobe Light. Automatically sounds when the BE is switched on to notify personnel that the BE is in use.

Blue Light ''(if equipped)'' - Mounted at an elevated position on either end of the extractor which project a bright, highly concentrated blue beam pattern on the ground visually alerting personnel to the direction the extractor is moving.

=== <big>Operation Overview</big> ===

* All operators should be familiar with the operator console of the extractor before performing any battery changes. The controls of the console are simple and well marked. It consists of six, manually operated, hydraulic control valves and a three position selector switch which controls the left and right vacuum cups (or optional magnets).
* The operator shall make certain there are no persons or obstacles in the extractor path prior to traveling forward or reverse.
* All manual valves are moved in the direction of the function travel which it controls with exception of the lift/lower valve, which is pulled toward the operator for "up" and pushed away for "down."
* In the event of any failure or malfunction, step off the dead-man switch or press the E-stop button and all functions will stop immediately, locking all hydraulics in place.
* The extractor arm must be in the center of the carriage or the unit will not travel forward or reverse.
* To ensure smooth operation, all valve movements should be made in a slow, deliberate motion.
* Only one key should be provided to operate the extractor.
* When leaving the machine, the operator shall turn off the key switch, remove the key and logout out of the IIoT (if equipped) to prevent unauthorized use
* Ensure all the batteries and cables are properly stored in the battery stands prior to moving the BE.
* The BE is designed to carry only one battery in each compartment on the carriage.
* When loading the BE, position the batteries in the center of the compartments on the powered rollers to prevent any battery movement when transporting.
* Ensure there are no projections outside of the carriage before moving the BE.

=== <big>Operating Instructions</big> ===

==== <big>Pre-Change Out Preparation</big> ====
1. Position lift truck for change out in designated area.

2. Remove all battery restraints and disconnect battery cables following manufacturers guidelines. (Be sure to position battery cables so as not to be damaged by the battery during change out.)

3. Board battery extractor and close safety gate. (Gate must be fully closed or unit will not operate.)

4. Turn key switch to "ON" position.

5. Log in on the HMI display (if equipped with BE-IIoT package).

6. Depress foot pedal.

==== <big>Discharged Battery Removal</big> ====
1. Move extractor forward or reverse to position center of empty compartment with center of lift truck battery compartment. (Lead roller of extractor is equipped with a centering groove. Users may find it beneficial to mark center of lift truck compartment to aid in alignment.)

2. Align extractor's roller compartment height with lift truck's battery compartment.

3. Rotate extractor arm into battery compartment aligned in Step 2.

4. Move extractor arm toward battery until vacuum cup/magnet contacts battery.

[[File:NOTICE-warn.png|alt=NOTICE|frameless|120x120px|link=https://tech.bhs1.com/index.php/File:NOTICE-warn.png]] '''DO NOT force cup/magnet into battery after initial contact with battery is made.'''

5. Energize vacuum/magnet by turning selector switch to proper direction, left or right.

6. Move extractor arm away from lift truck toward center of extractor roller bed, removing discharged battery. (Battery should be pulled past first three idler rollers onto first or second powered roller.)

7. Turn off vacuum/magnet and move extractor arm away from battery 1" to 2".

8. Rotate extractor arm out of battery compartment into opposite compartment (if empty) and center arm in carriage.

9. Move battery into center of compartment using powered rollers.

==== <big>Charged Battery Retrieval</big> ====
1. Locate charged battery for appropriate type of lift truck being changed.

2. Raise battery extractor roller compartment to proper level to gain access as needed to disconnect desired battery from its charger and disengage battery safety stop.

[[File:WARNING-warn.png|alt=WARNING|frameless|120x120px|link=https://tech.bhs1.com/index.php/File:WARNING-warn.png]] '''ALWAYS be sure charging has been completed and charger is not still charging battery. Dangerous sparking/arcing can occur if battery is unplugged from charger while charging.'''

3. Move extractor to appropriate rack position and align empty roller compartment with the center of the battery storage rack compartment. ''(The battery safety stop of each compartment is the center of that compartment and should be used for alignment with the groove in the lead roller of the battery extractor compartment.'')

4. Rotate arm into empty compartment (if not already positioned there.)

5. Move extractor arm toward battery until vacuum cup/magnet contacts battery.

6. Energize vacuum cup/magnet by turning selector switch to proper direction, left or right.

[[File:NOTICE-warn.png|alt=NOTICE|frameless|120x120px|link=https://tech.bhs1.com/index.php/File:NOTICE-warn.png]] '''DO NOT force cup/magnet into battery after initial contact with battery is made.'''

7. Move extractor arm away from battery rack toward center of extractor roller bed, removing charged battery. (Battery should be pulled past first three idler rollers onto first or second powered roller.)

8. Turn off vacuum/magnet and move extractor arm away from battery 1" to 2".

9. Rotate extractor arm out of battery compartment into fully vertical position.

10. Move battery into center of compartment using powered rollers.

==== <big>Discharged Battery Return</big> ====
1. If required, adjust extractor compartment height to battery rack level with open battery compartment. Drive extractor to align roller compartment containing discharged battery with open battery compartment.

2. Return discharged battery to battery rack using powered rollers.

'''''NOTE:''''' ''In most instances, batteries can be deposited into battery racks in one motion using only powered rollers. When this does not work, the battery may need slight assistance from extractor arm. To do this, rotate arm into compartment such as one would if removing battery from rack. If extractor is vacuum equipped, position top edge of cup slightly higher than edge of battery (or over lifting eye if so equipped) to prevent cup from adhering to battery - No vacuum/magnet is necessary for pushing. DO NOT activate vacuum/magnet switch. Slowly push battery into rack until fully into compartment.''

3. Engage battery safety stop and connect battery to charger as required.

==== <big>Charged Battery Installation</big> ====
1. Lower extractor to fully lowered position.

2. Drive extractor back to lift truck and align roller compartment containing charged battery as performed in steps 1 and 2 of "Discharged Battery Removal".

3. Move charged battery toward lift truck compartment by using powered rollers, verifying precise battery alignment.

[[File:NOTICE-warn.png|alt=NOTICE|frameless|120x120px|link=https://tech.bhs1.com/index.php/File:NOTICE-warn.png]] '''Many batteries are a tight fit into lift truck battery compartments. Care MUST be taken to ensure alignment is precise to avoid damage to battery, lift truck, and/or battery extractor.'''

4. Adjust extractor vertically as well as horizontally, if needed

5. Insert battery into lift truck as far as possible using only the powered rollers.

6. Rotate extractor arm into compartment and SLOWLY push battery into lift truck. (Be sure to watch battery cables for interference.)

7. Return extractor arm to center of roller bed and lower extractor to fully lowered position. Drive extractor out of immediate area.

8. Turn off key switch, remove key from switch, log out on the HMI display (if equipped with BE-IIoT package) and carefully exit extractor.

9. Secure newly installed battery in lift truck and reconnect battery cables.

10. Return lift truck to service
{|
![[File:Caution-Warning.png|alt=CAUTION|frameless|120x120px|link=https://tech.bhs1.com/index.php/File:Caution-Warning.png]]
|'''DO NOT drive the BE into the travel path end stops. The end stops are designed to prevent the BE from accidentally traveling beyond its designated travel path. Driving the BE into the end stops will cause the BE to stop suddenly, possibly causing damage to the end stop, the BE and/or personal injury.'''
|}

==== <big>Optional Powered Roller Cutout Operation</big> ====
Units equipped with optional Powered Roller Cutout, the powered roller override button must be depressed in addition to actuating the hydraulic valve when a battery disrupts the photo eye(s) at the edge of the battery compartments while using the powered rollers to transfer batteries on and off of the battery extractor.

==== <big>IIoT Equipped Units</big> ====
Units shipped after February, 2020 are equipped with BE-IIoT (Industrial Internet of Things) package. Operators must log in to the BE-IIoT system using the HMI (Human Machine Interface) display located on the dashboard to operate the extractor.

When finished operating the extractor, the operator should log out of the BE-IIoT to prevent unauthorized access and/or operation of the extractor.

== <big>Manual Unloading</big> ==
'''Lockout/tagout and de-energize all equipment prior to manually unloading any battery.'''

In the event of power loss or an operational malfunction of the BE not allowing a battery to be unloaded using normal operating procedures, it is recommended a battery be removed from the BE using certified and approved vertical extraction methods and devices.
{|
|[[File:DANGER-warn.png|alt=DANGER|frameless|120x120px|link=https://tech.bhs1.com/index.php/File:DANGER-warn.png]]
|'''Read, understand and observe all safety warnings and procedures related to the vertical extraction device(s) being used.'''
|}
Should the status of the BE not allow for safe vertical extraction (due to position in the battery aisle or level of the inner carriage), only repairs required to safely maneuver the BE to a position allowing for safe vertical extraction should be made. Once any batteries are safely unloaded, any remaining repairs can be made.
{|
|[[File:DANGER-warn.png|alt=DANGER|frameless|120x120px|link=https://tech.bhs1.com/index.php/File:DANGER-warn.png]]
|'''Extreme care should be taken when working under or around equipment supporting elevated loads. Unexpected movement of the equipment could cause the load and/or equipment to fall. ALWAYS be sure devices of adequate size and strength are in place to prevent any personnel working under the elevated load from being crushed. Serious personal injury or death will occur.'''
|}

== <big>Spare Parts List</big> ==
Use only BHS approved replacement parts.

Refer to the appropriate Spare Parts Kit (vacuum equipped units - Pt# BE-SPKV-TS, magnet equipped units - Pt# BE-SPKM-TS) for the list of items recommended by BHS to have on hand for BE-TS models to minimize any downtime due to minor breakdowns that may occur under normal operating conditions.

BHS offers many replacement parts kits containing relevant or related parts when replacing certain individual parts or replacing any obsolete / upgraded parts.

BHS also offers a supplement hose kit (Pt# 80342003) which contains an assortment of hoses allowing any hose on the extractor to be replaced immediately with a temporary hose of equal length or longer. After the extractor is back up and running, the failed hose can be taken to have an exact replacement made. Once the new hose is made and installed, the temporary hose can be returned to the kit for future use.

Go to [[www.bhs1.com]] and click "Parts" for all the latest parts kits and corresponding installation instructions (if applicable).

BHS recommends that a full maintenance inspection report similar to the one provided be done at least once a month.

Any parts found to be excessively worn or damaged should promptly be replaced unless said parts pose a safety risk to the operator and/or extractor, in which case the unit should be removed from service until the problem(s) are remedied (See

Operator's Daily Checklist.)

''Note: Spare parts kits contain parts for the most current machine design/configuration. Due to continuous design and manufacturing updates and improvements, not all the parts in the spare parts kits may be compatible with older units. Consult factory when ordering spare or replacement parts for existing units in the field to ensure part compatibility.''

= <big>Parts Sections</big> =

== <big>Chassis</big> ==

=== <big>Equalization Components</big> ===
[[File:BE-TS Equalization Components.png|alt=BE-TS Chassis Equalization|frameless|548x548px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|PT0222-1
|LINK-CONNECTING-#60
|
|
|8
|-
|2
|HW0017
|NUT-HEX-3/4-10
|
|
|8
|-
|3
|HW0115
|WASHER-LOCK-3/4"
|
|
|4
|-
|4
|43097001
|STUD-ANCHOR-5"
|
|''Upper''
|4
|-
|5
|HW0020
|NUT-JAM-3/4-10
|
|
|4
|-
|6
|43097002
|STUD-ANCHOR-2"
|
|''Lower''
|4
|-
|7
|00158001-14
|CHAIN-ROLLER-#60
|
|
|4
|}
[[File:BE-TS Equalization Components - 1.0.2.png|alt=BE-TS Chassis Equalization 2|frameless|575x575px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|PT0416
|COLLAR-SHAFT-1 1/2"
|
|
|4
|-
|2
|43097006
|KEY-3/8" X 2 3/4"
|
|
|4
|-
|3
|PT0224
|SPROCKET-60B12 X 1 1/2"
|
|''Keyed in line''
|8
|-
|4
|PT0405
|FLANGE BEARING-2 BOLT-1 1/2"
|
|
|4
|-
|5
|HW0502
|BOLT-HHCS-1/2-13 X 1 1/4"
|
|
|8
|-
|6
|HW0110
|WASHER-LOCK-1/2"
|
|
|8
|-
| rowspan="4" |7
|43127001
|SHAFT-EQUALIZATION-81.75"
|
|''BE-24-2-TS''
|2
|-
|43327001
|SHAFT-EQUALIZATION-105.75"
|
|''BE-36-2-TS''
|2
|-
|44327001
|SHAFT-EQUALIZATION-117.75"
|
|''BE-42-2-TS''
|2
|-
|44527001
|SHAFT-EQUALIZATION-75.75"
|
|''BE-42-1-TS''
|2
|-
| rowspan="2" |8
|PT0503
|BEARING-FLANGED LOAD-2 1/4"
|
|''Used after December 2003''
|8
|-
|43026001
|BEARING-FLANGED LOAD-2 1/4" ''(MACHINED)''
|
|''Used prior to December 2003''
|8
|-
|9
|HW0025
|NUT-JAM-7/8-14
|
|
|8
|-
|10
|HW0117
|WASHER-LOCK-7/8" ''(NOT SHOWN)''
|
|''Used prior to August 2002''
|8
|}

=== '''<big>Bridge & Cross Bar</big>''' ===
[[File:BE-TS Bridge and Cross Bar.png|alt=BE-TS Bridge and Cross Bar|frameless|524x524px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HW0502
|BOLT-HHCS-1/2-13 X 1 1/4"
|
|
|12
|-
|2
|HW0110
|WASHER-LOCK-1/2"
|
|
|20
|-
|3
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|20
|-
|4
|HW0515
|BOLT-HHCS-1/2-13 X 2"
|
|''Fully Threaded''
|8
|-
|5
|HW0007
|NUT-HEX-1/2-13
|
|
|8
|}

=== '''<big>Lift Cylinder Connections</big>''' ===
[[File:BE-TS Lift Cylinder Connections.png|alt=BE-TS Lift Cylinder Connections|frameless|589x589px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|00158001-13
|CHAIN-ROLLER-#80
|
|
|4
|-
|2
|HW0014
|NUT-HEX-1-8
|
|
|8
|-
|3
|43897002
|STUD-LIFT-INNER FRAME
|
|
|4
|-
|4
|PT0204
|LINK-CONNECTING-#80
|
|
|8
|-
|5
|43897001
|STUD-LIFT-OUTER FRAME
|
|
|4
|-
|6
|43815018
|BRACKET-CYLINDER SUPPORT
|
|
|4
|-
|7
|SS0761
|U-BOLT-CYLINDER MOUNTING
|
|
|4
|-
|8
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|12
|-
|9
|HW0107
|WASHER-LOCK-3/8"
|
|
|12
|-
|10
|HW0005
|NUT-HEX-3/8-16
|
|
|8
|-
| rowspan="2" |11
|HW0514
|BOLT-HHCS-1/2-13 X 2 1/2"
|
|''Idler caster end of unit''
|2
|-
|HW0504
|BOLT-HHCS-1/2-13 X 2"
|
|''Drive wheel end of unit''
|2
|-
|12
|HW0110
|WASHER-LOCK-1/2"
|
|
|4
|-
|13
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|4
|-
|14
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|4
|-
|15
|43822002
|CLEVIS ASSEMBLY
|
|''Sold as assembly only''
|4
|}

=== '''<big>Guidance Arm</big>''' ===
[[File:BE-TS Guidance Arm.png|alt=BE-TS Guidance Arm|frameless|562x562px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
! colspan="2" |NO. REQ
|-
|1
|43015011
|GUIDE ARM WELDMENT, 2 ROLLER
|
|
|2
|<nowiki>-</nowiki>
|-
|2
|43017025
|SPACER-GUIDE ARM
|
|''† 1/2" thick''
|4
|<nowiki>-</nowiki>
|-
|3
|41215204
|GUIDE ARM WELDMENT, 4 ROLLER
|
|
|<nowiki>-</nowiki>
|2
|-
|4
|41217274
|SPACER-GUIDE ARM
|
|
|<nowiki>-</nowiki>
|4
|-
|5
|43012007
|CAM ROLLER-1 3/4"
|
|
|4
|8
|-
|6
|HW0115
|WASHER-LOCK-3/4"
|
|
|4
|8
|-
|7
|HW0011
|NUT-HEX-3/4-16
|
|
|4
|8
|-
|8
|HW0509
|BOLT-HHCS-1/2-13 X 4-1/2"
|
|
|4
|6
|-
|9
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|4
|6
|-
|10
|HW0110
|WASHER-LOCK-1/2"
|
|
|4
|6
|-
|11
|HW0007
|NUT-HEX-1/2-13
|
|
|4
|6
|-
|12
|41215234
|GUIDE ARM WELDMENT (POLY)
|
|
|2
|<nowiki>-</nowiki>
|-
|13
|41217317
|POLY SLIDE MOUNTING BLOCK
|
|
|4
|<nowiki>-</nowiki>
|-
|14
|41217318
|POLY SLIDE
|
|
|4
|<nowiki>-</nowiki>
|-
|15
|HW0501
|BOLT-HHCS-1/2-13 X 1"
|
|
|12
|<nowiki>-</nowiki>
|-
|16
|HW0110
|WASHER-LOCK-1/2"
|
|
|12
|<nowiki>-</nowiki>
|-
|17
|91253A546
|BOLT FHSCS-1/4-20 X 1-1/2"
|
|
|8
|<nowiki>-</nowiki>
|-
|18
|HW0003
|NUT-NILN-1/4-20
|
|
|8
|<nowiki>-</nowiki>
|-
! colspan="7" |NOTES
|-
| colspan="7" |''† Older units equipped with (1) 1" thick spacer per guide arm bracket.''
|-
| colspan="7" |''†† Multiple styles of guide arms have been utilized on extractors. Refer to the parts diagrams for correct replacement parts.''
|}

=== '''<big>Roller Bed Componenets</big>''' ===
==== '''<big>''Idler Rollers''</big>''' ====
[[File:BE-TS Idler Rollers.png|alt=BE-TS Idler Rollers|frameless|746x746px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="3" |1
|43182001
|LEAD ROLLER ASSEMBLY-24"
|
|''With alignment groove''
|4
|-
|43382001
|LEAD ROLLER ASSEMBLY-36"
|
|''With alignment groove''
|4
|-
|43482001
|LEAD ROLLER ASSEMBLY-42"
|
|''With alignment groove''
|4
|-
| rowspan="3" |2
|43182002
|IDLER ROLLER ASSEMBLY-24"
|
|
|8
|-
|43382002
|IDLER ROLLER ASSEMBLY-36"
|
|
|8
|-
|43482002
|IDLER ROLLER ASSEMBLY-42"
|
|
|8
|-
| rowspan="3" |3
|43187002
|SHAFT-HEX-.75" X 25.75"
|
|''24" compartments''
|8
|-
|43387002
|SHAFT-HEX-.75" X 37.75"
|
|''36" compartments''
|8
|-
|43487002
|SHAFT-HEX-.75" X 43.75"
|
|''42" compartments''
|8
|-
| rowspan="3" |4
|43187003
|SHAFT-HEX-.75" X 27.5"
|
|''24" compartments''
|4
|-
|43387003
|SHAFT-HEX-.75" X 39.5"
|
|''36" compartments''
|4
|-
|43487003
|SHAFT-HEX-.75" X 45.5"
|
|''42" compartments''
|4
|-
|5
|HW1058
|PIN-HITCH
|
|
|24
|}
'''<big>''Powered Rollers''</big>'''

[[File:BE-TS Powered Rollers.png|alt=BE-TS Powered Rollers|frameless|546x546px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="3" |1
|43182003
|POWERED ROLLER-24"
|
|
|10
|-
|43382003
|POWERED ROLLER-36"
|
|
|10
|-
|43485003
|POWERED ROLLER-42"
|
|
|10
|-
|2
|43087001
|JOURNAL-POWERED ROLLER
|
|
|10
|-
|3
|PT0404
|FLANGE BEARING-3-BOLT-1"
|
|
|20
|-
|4
|HW0321
|BOLT-HHCS-5/16-18 X 1 1/4"
|
|
|60
|-
|5
|HW0105
|WASHER-LOCK-5/16"
|
|
|60
|-
|6
|HW0004
|NUT-HEX-5/16-18
|
|
|60
|-
|7
|PT0033
|SPROCKET-35B18 X 1"
|
|
|16
|-
|8
|00197028
|KEY-1/4" X 1 1/4"
|
|
|8
|-
|9
|00158001-16
|CHAIN-ROLLER-#35
|
|
|8
|-
|10
|PT0031
|LINK-CONNECTING-#35
|
|
|8
|-
|11
|PT0418
|COLLAR-SHAFT-1"
|
|
|10
|}
[[File:BE-TS Powered Rollers Detail A.png|alt=BE-TS Powered Rollers Detail A|frameless|542x542px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0120
|MOTOR-HYDRAULIC-160CC
|
|
|2
|-
|2
|HW1071
|KEY-WOODRUFF-#808 STD
|
|''Supplied with Item 1''
|A/R
|-
|3
|H1544
|ADAPTER-#6 JICM X #10 SAEM
|
|
|4
|-
|4
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|18
|-
|5
|HW0107
|WASHER-LOCK-3/8"
|
|
|18
|-
|6
|43017004
|PLATE-MOTOR MOUNTING
|
|
|2
|-
|7
|PT0302-1
|COUPLING BODY-#40 X 1"
|
|
|4
|-
|8
|PT0301
|CHAIN-COUPLING-#40
|
|''Includes connecting pin''
|2
|-
|9
|00197026
|KEY-1/4" X 1"
|
|
|2
|-
|10
|43097003
|KEY-1/4" X 5/8"
|
|
|2
|}

=== '''<big>Hose Carrier</big>''' ===
[[File:BE-TS Hose Carrier.png|alt=BE-TS Hose Carrier|frameless|550x550px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|PT0629
|CARRIER TRACK
|
|''81 links required''
|10'
|-
|2
|PT0631
|BRACKET-UPPER MOUNTING
|
|
|1
|-
|3
|HW0212
|SCREW-RHMS-#10-24 X 1/2"
|
|
|2
|-
|4
|HW0032
|NUT-NILN-#10-24
|
|
|2
|-
|5
|PT0630
|BRACKET-LOWER MOUNTING
|
|
|1
|-
|6
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|6
|-
|7
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|2
|-
|8
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|2
|-
|9
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|10
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|-
|11
|43817056-2
|BRACKET-CARRIER TRACK MOUNTING
|
|
|1
|-
|12
|HW0401
|BOLT-HHCS-3/8-16 X 3/4"
|
|
|4
|-
|13
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|14
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|4
|-
|15
|43817057
|PLATE-CARRIER TRACK SUPPORT
|
|
|1
|-
|16
|HW0504
|BOLT-HHCS-1/2-13 X 2"
|
|
|2
|-
|17
|HW0110
|WASHER-LOCK-1/2"
|
|
|2
|-
|18
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|2
|}

=== <big>'''Cable Retractor'''</big> ===
[[File:BE-TS Cable Retractor.png|alt=BE-TS Cable Retractor|frameless|585x585px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|CCR-12HD
|TAKE UP REEL-CARRIER TRACK
|
|
|1
|-
|2
|HW0403
|BOLT-HHCS-3/8-16 X 1 1/4"
|
|
|2
|-
|3
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|4
|-
|4
|HW0107
|WASHER-LOCK-3/8"
|
|
|2
|-
|5
|HW0005
|NUT-HEX-3/8-16
|
|
|2
|}

=== '''<big>Operator Gate</big>''' ===
[[File:BE-TS Discontinued Drop Bar Operator Gate.png|alt=BE-TS Discontinued Drop Bar Operator Gate|frameless|568x568px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43015004
|GATE-OPERATOR
|
|
|1
|-
|2
|HW0407
|BOLT-HHCS-3/8-16 X 2 3/4"
|
|
|1
|-
|3
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|2
|-
|4
|HW0006
|NUT-NILN-3/8-16
|
|
|1
|}
[[File:BE-TS Operator Gate Continued.png|alt=BE-TS Operator Gate Continued|frameless|552x552px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43017064-2
|LATCH-SWING GATE
|
|
|1
|-
|2
|HW0418
|BOLT-HHCS-3/8-16 X 2 1/4"
|
|
|1
|-
|3
|HW0031
|NUT-LOCK-3/8-16
|
|
|1
|-
|4
|N/A
|HINGE-SPRING
|
|''† See notes''
|1
|-
|5
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|3
|-
|6
|HW1037
|STOP-GATE
|
|
|1
|-
|7
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|1
|-
|8
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|1
|-
|9
|HW0003
|NUT-NILN-1/4-20
|
|
|1
|-
|10
|N/A
|TORSION SPRING
|
|''† See notes''
|1
|-
|11
|HW0816
|SCREW-HHCS-SELF DRILLING-#10 X 3/4"
|
|
|4
|-
|12
|43806001
|ANTI-FATIGUE MAT
|
|
|1
|-
|13
|43017058-2
|THRESHOLD
|
|
|1
|-
|14
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|2
|-
|15
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|4
|-
|16
|HW0107
|WASHER-LOCK3/8"
|
|
|2
|-
|17
|HW0005
|NUT-HEX-3/8-16
|
|
|2
|-
|18
|HW9002
|GAS SPRING
|80292015
|
|1
|-
|19
|43017086-2
|BRACKET-MOUNTING-SPRING
|80292015
|
|2
|-
|20
|HW0815
|SCREW-SELF DRILLING-#12-24 X 1" T-4
|80292015
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Part Discontinued. Spring Hinge and Torsion Spring must be replaced with Gas Spring Kit.''
|}

=== '''<big>Guarding</big>''' ===

==== '''''<big>Outer Carriage Guards</big>''''' ====

===== '''''1-Piece Outside Frame Guarding''''' =====
[[File:BE-TS Outside Frame Guard 1-Piece.png|alt=BE-TS Outside Frame Guard 1-Piece|frameless|550x550px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43817038
|GUARD-FAR END-TOP
|
|
|1
|-
|2
|43817037
|GUARD-FAR END-MIDDLE
|
|
|1
|-
|3
|43817035
|GUARD-FAR END-BOTTOM
|
|
|1
|-
|4
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|33
|}

===== '''''Split Outside Frame Guarding''''' =====
[[File:BE-TS Outside Split Frame Guard.png|alt=BE-TS Outside Split Frame Guard|frameless|562x562px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43817103
|GUARD-FAR END-TOP
|
|
|1
|-
|2
|43817102
|GUARD-FAR END-MIDDLE
|
|
|1
|-
|3
|43817101
|GUARD-FAR END-BOTTOM
|
|
|1
|-
|4
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|37
|}

==== '''<big>''Inner Carriage Guards''</big>''' ====

===== '''''Inner Carriage Guards (Rotary Actuator)''''' =====
[[File:BE-TS Inner Carriage Guard Rotary.png|alt=BE-TS Inner Carriage Guard (Rotary Actuator Units)|frameless|554x554px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43817041-2
|GUARD-FRONT-OPERATOR CONSOLE
|
|
|1
|-
|2
|43817042-2
|GUARD-INNER-FRAME
|
|
|2
|-
|3
|43014006-2
|GUARD-LINEAR DRIVE SCREW
|
|
|1
|-
| rowspan="2" |4
|43017010-2
|GUARD-SIDE-ARM CARRIER SHAFT
|
|
|2
|-
|44517002-2
|GUARD-SIDE-ARM CARRIER SHAFT
|
|''† Single compartment units only''
|1
|-
|5
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|34
|-
|6
|43017009-2
|BRACKET-SCREW GUARD MOUNTING
|
|
|2
|-
|7
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|4
|-
|8
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|9
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|8
|-
|10
|HW0103
|WASHER-LOCK-1/4"
|
|
|8
|-
|11
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Single Compartment Guard replaces standard, Far Side Arm Carrier Shaft Guard.''
|}
'''''Inner Carriage Guards (Helical Actuator)'''''

[[File:BE-TS Inner Carriage Guard Helical Actuator.png|alt=BE-TS Inner Carriage Guard (Helical Actuator Units)|frameless|547x547px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43817041-2
|GUARD-FRONT-OPERATOR CONSOLE
|
|
|1
|-
|2
|43817042-2
|GUARD-INNER-FRAME
|
|
|2
|-
| rowspan="2" |3
|43017081-2
|GUARD-SIDE-ARM CARRIER SHAFT
|
|
|2
|-
|44517003-2
|GUARD-SIDE-ARM CARRIER SHAFT
|
|''† Single compartment units only''
|1
|-
|4
|43017080-2
|BRACKET-SIDE GUARD MOUNTING
|
|
|2
|-
|5
|43017082-3
|MOUNT-CHAIN GUARD-LEAD SCREW
|
|
|1
|-
|6
|43017082-4
|MOUNT-CHAIN GUARD-LEAD SCREW
|
|
|1
|-
|7
|43017083-2
|GUARD-CHAIN-LEAD SCREW
|
|
|1
|-
|8
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|9
|HW0103
|WASHER-LOCK-1/4"
|
|
|8
|-
|10
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|8
|-
|11
|HW0347
|BOLT-BHSCS-1/4-20 X 3/8"
|
|
|4
|-
|12
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|28
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Single Compartment Guard replaces standard, Far Side Arm Carrier Shaft Guard.''
|}

==== '''<big>''Dash & Platform Guards''</big>''' ====
[[File:BE-TS Dash & Platform Guards.png|alt=BE-TS Dash & Platform Guards|frameless|557x557px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41614004-2
|DASHBOARD-OPERATOR CONSOLE
|
|
|1
|-
|2
|43817040
|KICK PLATE-OPERATOR CONSOLE
|
|''41.5" high''
|1
|-
|3
|43817086-2
|DASHBOARD-OPERATOR CONSOLE
|
|
|1
|-
|4
|43817088
|KICK PLATE-OPERATOR CONSOLE
|
|''33.5"'' ''high''
|1
|-
|5
|43817110-2
|FRAME-DASHBOARD
|
|
|1
|-
|6
|A/R
|PLATE-DASHBOARD
|
|''† See notes''
|1
|-
|7
|HW0060
|NUT-CLIP-#10-24
|
|
|12
|-
|8
|SS0114
|BHSCS-#10-24 X 1/2"-SST
|
|
|12
|-
|9
|PL0602
|VINYL EDGING
|
|''At Foot Switch (Not shown)''
|1'
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Consult factory''
|}

==== '''''<big>Lift Cylinder Guards</big>''''' ====
[[File:BE-TS Lift Cylinder Guards.png|alt=BE-TS Lift Cylinder Guards|frameless|548x548px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="2" |1
|43815016
|GUARD-CLEVIS
|
|Operator right / Far left
|2
|-
|43815017
|GUARD-CLEVIS
|
|Operator left / Far right
|2
|-
|2
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|8
|}

=== '''<big>Labels & Placards</big>''' ===
[[File:BE-TS Labels & Placards Chassis.png|alt=BE-TS Labels & Placards Chassis|frameless|546x546px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|00196616
|LABEL-"NO RIDERS ALLOWED"
|
|
|1
|-
|2
|00196210
|LABEL-WARNING-"OPERATION BY AUTHORIZED PERSONNEL ONLY"
|
|
|1
|-
|3
|43696001
|PLACARD-OFF / ON
|
|
|1
|-
|4
|43096018
|PLACARD-RACK LEVEL ASSIST
|
|''† If equipped''
|1
|-
|5
|43096015
|PLACARD-PLATFORM RAISE / LOWER
|
|
|1
|-
|6
|43096010
|PLACARD-HORN
|
|''† If equipped''
|1
|-
|7
|43096016
|PLACARD-DRIVE / ARM ROTATION
|
|
|1
|-
| rowspan="2" |8
|43096012
|PLACARD-VACUUM OFF / ON
|
|''Vacuum units only''
|1
|-
|43096011
|PLACARD-MAGNET OFF / ON
|
|''Magnet units only (Not shown)''
|1
|-
|9
|43096017
|PLACARD-POWERED ROLLER CUTOUT OVERRIDE
|
|''† If equipped''
|1
|-
|10
|43096013
|PLACARD-POWERED ROLLERS / ARM TRAVERSE
|
|
|1
|-
|11
|00196633
|LABEL-NOTICE-"IN LINE VACUUM FILTER..."
|
|''(1) per side (Vacuum units only)''
|2
|-
|12
|SM-1197
|LABEL-ARM POSITION ARROW
|
|
|2
|-
|13
|00196609
|LABEL-NOTICE-"ARM MUST BE POSITIONED BETWEEN ARROWS..."
|
|
|1
|-
|14
|00196602
|LABEL-NOTICE-"LUBRICATION POINTS ON UNDERSIDE"
|
|
|2
|-
|15
|00196218
|LABEL-WARNING-"ELECTRICAL VOLTAGE HAZARD"
|
|''Magnet units only''
|1
|-
|16
|00196238
|LABEL-WARNING-"STRONG MAGNETIC

FIELD/DO NOT USE WITH PACEMAKER"
|
|''†† Magnet units only''
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Rack Level Assist (LAI), Horn and Powered Roller Cutout (PRC) are optional features. Not all units are equipped with these options.''
|-
| colspan="6" |''†† Pacemaker Warning Label takes the place of the discontinued, Triangular Magnetic Field Label.''
|}
[[File:BE-TS Labels & Placards Frame.png|alt=BE-TS Labels & Placards Frame|frameless|549x549px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|00196004
|LABEL-CAUTION-"WATCH FOR BATTERY AND CHARGER CABLES IN TRAVEL PATH"
|
|
|1
|-
|2
|00196216
|LABEL-WARNING-"CHAIN ENTANGLEMENT

HAZARD"
|
|''(1) per Clevis Guard''
|4
|-
|3
|00196622
|LABEL-LIFT POINT
|
|''(2) each end''
|4
|-
|4
|00196700
|DECAL-BHS-24" X 7.875"
|
|''Far end (Not shown)''
|2
|-
| rowspan="2" |5
|00196630
|LABEL-NOTICE-HYD. OIL SPEC. (AW 68)
|
|''† See notes''
|1
|-
|00196645
|LABEL-NOTICE-HYD. OIL SPEC. (AW 32)
|
|''† See notes''
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |† Most units shipped prior to December 2014 require AW 68 Hydraulic Oil. Some units shipped prior to December 2014 shipped with AW 32 for low temperature applications.
|}

== <big>Extractor Arm</big> ==
{| class="wikitable"
!SYMBOL
!DESCRIPTION / NOTICE
!ACTUATOR DIAGRAM
|-
|[[File:IOP-400 BE-SL&DS (10-23) Rotary Actuator Symbol.png|alt=Rotary Actuator Symbol|frameless|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_Rotary_Actuator_Symbol.png]]
|
==='''<big>Rotary Actuator Symbol</big>'''===
Battery Extractors shipped prior to May 2020 are equipped with Rotary Actuator Extractor Arms. Parts Diagrams Specific to the Rotary Actuator design are indicated with the Rotary Actuator symbol.
|[[File:IOP-400 BE-SL&DS (10-23) Rotary Actuator Extractor Arm.png|alt=BE-TS Rotary Actuator|frameless|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_Rotary_Actuator_Extractor_Arm.png]]
|-
|[[File:IOP-400 BE-SL&DS (10-23) Helical Actuator Symbol.png|alt=Helical Actuator Symbol|frameless|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_Helical_Actuator_Symbol.png]]
|
===<big>'''Helical Actuator Symbol'''</big>===
Battery Extractors shipped from May 2020 to Present are equipped with Helical Actuator Extractor Arms. Parts Diagrams Specific to the Rotary Actuator design are indicated with the Helical Actuator Symbol.
|[[File:IOP-400 BE-SL&DS (10-23) Helical Actuator Extractor Arm.png|alt=BE-TS Helical Actuator|frameless|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_Helical_Actuator_Extractor_Arm.png]]
|}
===<big>Vacuum Components & Swing Arms</big>===
====''<big>Vacuum Arms (Rotary Actuator)</big>''====
[[File:BE-TS Vacuum Arms (Rotary Actuator).png|alt=BE-TS Vacuum Arms (Rotary Actuator)|frameless|619x619px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="2" |1
|N/A
|ARM-PUSH/PULL-30"
|
|''† Discontinued''
|1
|-
|N/A
|ARM-PUSH/PULL-36"
|
|''† Discontinued''
|1
|-
|2
|HW0509
|BOLT-HHCS-1/2-13 X 4 1/2"
|
|
|3
|-
|3
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|6
|-
|4
|HW0110
|WASHER-LOCK-1/2"
|
|
|3
|-
|5
|HW0007
|NUT-HEX-1/2-13
|
|
|3
|-
|6
|P0505
|BUSHING-RED-#6 NPT X #4 FNPT-BRASS
|
|
|2
|-
|7
|P0402
|HOSE BARB-1/4 X #4 MNPT-BRASS
|
|
|2
|-
|8
|HW0428
|STUD-VACUUM-3/8-16 X 5"
|HW-KIT-2
|
|8
|-
|9
|HW0108
|WASHER-FLAT-3/8"-SAE
|HW-KIT-2
|
|40
|-
|10
|HW1001
|SPRING-3/8"
|HW-KIT-2
|
|24
|-
|11
|HW0006
|NUT-NILN-3/8-16
|HW-KIT-2
|
|8
|-
|12
|HW0424
|NUT-JAM-3/8-16
|HW-KIT-2
|
|8
|-
|REF
|43052006
|ADJUSTABLE PUSH/PULL ARM
|
|''Includes Items 13 through 17''
|1
|-
|13
|43057034
|ARM BASE
|
|
|1
|-
|14
|43055008
|VACUUM CUP MOUNT
|
|
|2
|-
|15
|HW0523
|BOLT-HHCS-1/2-13 X 4"
|
|
|2
|-
|16
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|4
|-
|17
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† One-piece Arms no longer available. Must replace with Adjustable Arm.''
|}

====<big>''Vacuum Cups''</big>====
[[File:BE-TS Vacuum Cups.png|alt=Vacuum Cups|frameless|563x563px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="4" |A/R
|00162004
|VACUUM CUP-10" 3-PC (STANDARD)
|
|''† Includes Items 1 through 4''
| rowspan="4" |A/R
|-
|00162003
|VACUUM CUP-12" 3-PC (STANDARD)
|
|''† Includes Items 4 through 7''
|-
|00162007
|VACUUM CUP-10" 3-PC, REINFORCED
|
|''Includes Items 1,3,4 & 8''
|-
|00162005
|VACUUM CUP-12" 3-PC, REINFORCED
|
|''Includes Items 4,5,7 & 9''
|-
|1
|00164006
|CASTING-10" VACUUM CUP
|
| rowspan="3" |''10" cup only''
|1
|-
|2
|00164004
|SEAL-RUBBER-10"
|
|1
|-
|3
|00165002
|PLATE-FRONT-10"
|
|1
|-
|4
|HW0311
|BOLT-FHSCS-1/4-20 X 3/4"
|
|
|8
|-
|5
|00166001
|CASTING-12" VACUUM CUP
|
| rowspan="3" |''12" cup only''
|1
|-
|6
|00164001
|SEAL-RUBBER-12"
|
|1
|-
|7
|00165001
|PLATE-FRONT-12"
|
|1
|-
|8
|00164007
|SEAL-RUBBER-10"-REINFORCED
|
|
|A/R
|-
|9
|00167003
|SEAL-RUBBER-12"-REINFORCED
|
|
|A/R
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† 10" and 12" 1-Piece Cups no longer available. Must replace with 3-Piece Cup. Verify required cup size prior to ordering.''
|}

====<big>''Swing Arms (Rotary Actuator)''</big>====
[[File:BE-TS Swing Arms (Rotary Actuator).png|alt=BE-TS Swing Arms (Rotary Actuator)|frameless|552x552px]]
{| class="wikitable"
|ITEM
|BHS PART NUMBER
|DESCRIPTION
|REF. KIT NO.
|NOTES
|NO. REQ
|-
| rowspan="3" |1
|45055001
|TIE PLATE-SWING ARM
|
|BE-24-2-TS
|1
|-
|45255001
|TIE PLATE-SWING ARM
|
|BE-36-2-TS (NOT SHOWN)
|1
|-
|45355001
|TIE PLATE-SWING ARM
|
|BE-42-2-TS (NOT SHOWN)
|1
|-
|2
|43055004
|SWING ARM-RHS
|†
|NOT SOLD INDIVIDUALLY
|1
|-
|3
|43055002
|SWING ARM-LHS
|†
|NOT SOLD INDIVIDUALLY
|1
|-
|4
|HW0603
|BOLT-FHSCS-5/8-11 X 2"
|
|
|4
|-
|5
|HW0113
|WASHER-LOCK-5/8"
|
|
|4
|-
|6
|HW0010
|NUT-JAM-5/8-11
|
|
|4
|-
|7
|PT0413
|COLLAR-SHAFT-3"
|80252001
|
|2
|-
|8
|43027001
|SHAFT-ROTARY ACTUATOR
|80252001
|
|1
|-
|9
|HW1013
|KEY-3/8" X 12"
|80252001
|
|1
|-
|10
|PT0419
|BEARING-SAE 841-2" I.D., 3" OD, 1/8" THICK
|80252001
|
|3
|-
|11
|43052005
|CAP-BEARING
|
|INCLUDES BEARING
|2
|-
|12
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|6
|-
|13
|HW0103
|WASHER-LOCK-1/4"
|
|
|6
|-
|14
|43057014
|STANDOFF-WIRE
|
|
|1
|-
|15
|HW0312
|SCREW-SHSS-1/4-20 X 1"-CUP POINT
|
|
|1
|-
|16
|43057003
|CUSHION-SWING ARM
|
|
|2
|-
|17
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|4
|-
|18
|43055001
|STOP-SWING ARM
|
|
|2
|-
|19
|HW0403
|BOLT-HHCS-3/8-16 X 1 1/4"
|
|
|4
|-
|20
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|21
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|4
|-
|22
|H1565
|ADAPTER-45 DEG-#6 JICM X #4 MNPT
|
|
|2
|-
|23
|H1600
|ADAPTER-90 DEG-#6 JICM X #8 SAEM
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |† ''Included in multiple kits.''
|-
| colspan="6" |See ''Single Compartment Swing Arm Stop for the the Single Compartment Swing Arm Stop.''
|}

=== '''''Vacuum Swing Arm Stop (Rotary Actuator)''''' ===
[[File:BE-TS Single Compartment Swing Arms (Rotary Actuator).png|alt=BE-TS Single Compartment Swing Arms (Rotary Actuator)|frameless|575x575px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|44555001
|STOP-SWING ARM
|
|
|1
|-
|2
|43057003
|CUSHION-SWING ARM
|
|
|1
|-
|3
|43057008
|SPACER-SWING ARM STOP
|
|
|1
|-
|4
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|2
|-
|5
|HW0403
|BOLT-HHCS-3/8-16 X 1 1/4"
|
|
|4
|-
|6
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|}
====''<big>Vacuum Pump (Rotary Actuator)</big>''====
[[File:BE-TS Vacuum Pumps (Rotary Actuator).png|alt=BE-TS Vacuum Pumps (Rotary Actuator)|frameless|551x551px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|P0005
|PUMP-VACUUM
|
|
|1
|-
|2
|P0208
|FILTER-HI FLOW
|
|
|3
|-
|3
|P0503
|NIPPLE-#4 NPT-BRASS
|
|
|3
|-
|4
|P0502
|TEE-#4 FNPT-BRASS
|
|
|1
|-
|5
|P0506
|ELBOW-STR-90 DEG-#4 NPT-BRASS
|
|
|4
|-
|6
|P0402
|HOSE BARB-1/4 X #4 NPTM-BRASS
|
|
|6
|-
|7
|P0207
|VALVE-VACUUM RELEASE
|
|
|2
|-
|8
|P0302
|HOSE-VACUUM-1/4" I.D.
|
|''Two 6" pieces''
|1'
|-
|9
|P0302
|HOSE-VACUUM-1/4" I.D.
|
|''Short Arm side''
|1'
|-
|10
|P0302
|HOSE-VACUUM-1/4" I.D.
|
|''Long Arm side''
|2'
|-
|11
|E0611
|JUNCTION BOX-4" X 2" X 2"
|
|
|1
|-
|12
|E0612
|COVER-JUNCTION BOX
|
|
|1
|-
|13
|HW0212
|SCREW-RHMS-#10-24 X 1/2"
|
|
|2
|-
|14
|E0624
|CONNECTOR-1/2"
|
|
|1
|-
|15
|E0608-1
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .450" to .560"''
|1
|-
|15a
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|''Not shown''
|2
|-
| rowspan="2" |16
|E0501
|CORD-14-4 SW/SOW
|
|''Withtout Ground Connection in Arm''
| rowspan="2" |15'
|-
|E0514
|CORD-16-5 SW/SOW
|
|
|-
|17
|43057014
|STANDOFF-CABLE
|
|
|1
|-
|18
|HW0206
|SCREW-RHMS-#10-32 X 3/4"
|
|
|4
|-
|19
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|1
|-
|20
|43057021
|PLATE-STIFFENER
|†
|
|2
|-
|21
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|†
|
|12
|-
|22
|HW0107
|WASHER-LOCK-3/8"
|†
|
|12
|-
|23
|HW0005
|NUT-HEX-3/8-16
|†
|
|12
|-
|24
|HW0108
|WASHER-FLAT-3/8"-SAE
|†
|''Not shown''
|24
|-
|25
|P0111
|FILTER-VACUUM-INLINE
|
|''Not shown''
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |† ''Included in multiple kits.''
|}
===<big>Rotary Actuator</big>===
[[File:BE-TS Rotary Actuator.png|alt=BE-TS Rotary Actuator|frameless|557x557px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43046001
|ROTARY ACTUATOR
|
|
|1
|-
|2
|80000002
|ROTARY ACTUATOR BASE ASSEMBLY
|
|''Without Actuator''
|1
|-
|2A
|N/A
|VERTICAL CARRIER PLATE-OUTER
|
|''Included with 80000002''
|2
|-
|2B
|N/A
|VERTICAL CARRIER PLATE-INNER
|
|''Included with 80000002''
|1
|-
|2C
|N/A
|CARRIER BASE PLATE
|
|''Included with 80000002''
|1
|-
|3
|HW1070
|PIN-PULL DOWEL-5/8" X 1 1/2"
|
|
|2
|-
|4
|HW0508
|BOLT-SHCS-1/2-13 X 3/4"
|
|
|3
|-
|5
|HW1045
|PIN-PULL DOWEL-3/8" X 1 1/2"
|
|''Included with 80000002''
|6
|-
|6
|HW0412
|BOLT-SHCS-3/8-16 X 1 1/4"
|
|''Included with 80000002''
|12
|-
|7
|H0010
|FITTING-BULKHEAD-3/4-16 X #4 FNPT
|
|
|4
|-
|8
|H1579
|ADAPTER-90 DEG-#6 JICM X #4 NPTM
|
|
|2
|}
===<big>Carrier Shafts & Bearings ''(Rotary Actuator)''</big>===
[[File:BE-TS Rotary Actuator Carrier Shafts.png|alt=BE-TS Carrier Shafts (Rotary Actuator)|frameless|560x560px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43057045
|CARRIER SHAFT-EXTRACTOR ARM
|
|''† See notes''
|2
|-
|2
|43054007
|BEARING-EXTRACTOR ARM CARRIER
|80252002
|''†† See notes''
|4
|-
|3
|HW0412
|BOLT-SHCS-3/8-16 X 1 1/4"
|80252002
|
|16
|-
|4
|PT0413
|COLLAR-SHAFT-3"
|
|
|4
|-
|5
|PT0624
|FITTING-ZERK
|80252002
|''Not shown''
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† See [https://tech.bhs1.com/index.php/(BE-TS)_Triple_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-401)#Vacuum_Extended_Reach_(Rotary_Actuator) Vacuum Extended Reach (Rotary Actuator)] section for Extended Reach equipped units.''
|-
| colspan="6" |''†† See [https://tech.bhs1.com/index.php/(BE-TS)_Triple_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-401)#Carrier_Shafts_&_Bearings Carrier Shafts & Bearings (Helical Actuator)] section for Helical Actuator equipped units.''
|}

===<big>Drive Screw Components ''(Rotary Actuator)''</big>===
====''<big>Drive Nut Assembly (Rotary Actuator)</big>''====
[[File:IOP-400 BE-SL&DS (10-23) Drive Nut Assembly Rotary Actuator.png|alt=BE-SL&DS Drive Nut Assembly Rotary Actuator|frameless|537x537px|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_Drive_Nut_Assembly_Rotary_Actuator.png]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43054006
|DRIVE NUT ASSEMBLY
|80252003
|''†'' ''See notes''
|1
|-
|2
|HW0426
|BOLT-SHCS-3/8-16 X 5 1/2"
|80252003
|''††'' ''See notes''
|4
|-
|3
|HW0108
|WASHER-FLAT-3/8"-SAE
|80252003
|''††'' ''See notes''
|4
|-
|4
|HW0006
|NUT-NILN-3/8-16
|80252003
|''††'' ''See notes''
|4
|-
|5
|PT0624
|FITTING-ZERK
|80252003
|
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† See [https://tech.bhs1.com/index.php/(BE-TS)_Triple_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-401)#Drive_Nut_Assembly_(Helical_Actuator) Drive Nut Assembly (Helical Actuator)] section for Helical Actuator equipped units.''
|-
| colspan="6" |''†† It is recommended to replace mounting hardware when replacing Drive Nut Assembly.''
|}
====''<big>Drive Screw</big>''====
=====''[Current] Drive Screw Assembly (Frame #'s 374 to Present)''=====
[[File:IOP-400 BE-SL&DS (10-23) Drive Screw Rotary Current.png|alt=Current BE-SL & BE-DS Drive Screw (Rotary Actuator)|frameless|531x531px|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_Drive_Screw_Rotary_Current.png]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43024001
|SCREW-LINEAR DRIVE
|
|
|1
|-
|2
|PT0119
|SPROCKET-50B15 X 1 3/16"
|
|
|1
|-
|3
|43097004
|KEY-1/4 X 7/8"
|
|
|1
|-
|4
|00158001-15
|CHAIN-ROLLER-#50
|
|
|1
|-
|5
|PT0102
|LINK-CONNECTING-#50
|
|
|1
|-
|6
|PT0406
|FLANGE BEARING-4 BOLT-1 3/16"
|
|''Alloy casting''
|2
|-
|7
|HW0503
|BOLT-HHCS-1/2-13 X 1 1/2"
|
|
|8
|-
|8
|HW0110
|WASHER-LOCK-1/2"
|
|
|8
|-
|9
|PT0107
|SPROCKET-50B15 X 1"
|
|
|1
|-
|10
|HC0121
|MOTOR-HYDRAULIC-100CC
|
|''SAE 2-Bolt mount''
|1
|-
|11
|H1605
|ADAPTER-90 DEG-#6 JICM X #10 SAEM
|
|
|2
|-
|12
|HW1071
|KEY-WOODRUFF-#808 STD
|
|''Supplied with Item 10''
|A/R
|-
|13
|HW0403
|BOLT-HHCS-3/8-16 X 1 1/4"
|
|
|6
|-
|14
|HW0107
|WASHER-LOCK-3/8"
|
|
|6
|-
|15
|43017007
|PLATE-MOUNTING-SCREW DRIVE MOTOR
|
|
|1
|-
|16
|43057019
|PLATE-COVER
|
|
|2
|-
|17
|HW0415
|BOLT-SHCS-3/8-16 X 3/4"
|
|
|8
|}
{| class="wikitable"
! colspan="6" |ITEMS BELOW ARE REQUIRED FOR REPLACING THE LINEAR DRIVE

SCREW ON UNITS WITH FRAME #'S OF 373 AND EARLIER
|-
! colspan="6" |LINEAR DRIVE SCREW UPDATE KIT
|-
|REF
|80252011
|UPGRADE KIT
|
|
|1
|-
|1
|43024001
|SCREW-LINEAR DRIVE
|
|
|1
|-
|2
|PT0119
|SPROCKET-50B15 X 1 3/16"
|
|
|1
|-
|3
|43097004
|KEY-1/4" X 7/8"
|
|
|1
|-
|6
|PT0406
|FLANGE BEARING-4 BOLT-1 3/16"
|
|''Alloy casting''
|2
|-
|7
|HW0503
|BOLT-HHCS-1/2-13 X 1 1/2"
|
|
|8
|-
|8
|HW0110
|WASHER-LOCK-1/2"
|
|
|8
|-
|16
|43057019
|PLATE-COVER
|
|
|2
|-
|<nowiki>-</nowiki>
|43057022
|SHIM-18GA
|
|''May not be required'' - ''(Not shown)''
|2
|-
|<nowiki>-</nowiki>
|43057018
|TEMPLATE-BEARING MOUNT PATTERN
|
|''(Not shown)''
|1
|-
|<nowiki>-</nowiki>
|43057020
|SPACER PLATE
|
|''(Not shown)''
|2
|-
|<nowiki>-</nowiki>
|80000015
|INSTRUCTION DETAIL
|
|''(Not shown)''
|REF
|}

=====''[Discontinued] Drive Screw Assembly (Frame #'s 373 and Earlier)''=====
[[File:IOP-400 BE-SL&DS (10-23) Drive Screw (Rotary Actuator) Discontinued.png|alt=Discontinued BE-SL & BE-DS Drive Screw (Rotary Actuator)|frameless|532x532px|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_Drive_Screw_(Rotary_Actuator)_Discontinued.png]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|N/A
|SCREW-LINEAR DRIVE (DISCONTINUED)
|
|''See 80252011 Upgrade Kit''
|1
|-
|2
|PT0118
|SPROCKET-50B12 X 1 3/16"
|
|
|1
|-
|3
|43097004
|KEY-1/4" X 7/8"
|
|
|1
|-
|4
|00158001-15
|CHAIN-ROLLER-#50
|
|
|1
|-
|5
|PT0102
|LINK-CONNECTING-#50
|
|
|1
|-
|6
|43057016
|BLOCK-BEARING RETAINER
|
|
|2
|-
|6a
|PT0414
|RACE-TAPERED ROLLER BEARING
|
|''Included with 43057016''
|2
|-
|7
|PT0623
|SEAL-GREASE
|
|
|2
|-
|8
|HW0416
|BOLT-SHCS-3/8-16 X 1"
|
|
|8
|-
|9
|PT0415
|BEARING-TAPERED ROLLER
|
|
|2
|-
|10
|HW1050
|NUT-LOCK
|
|
|4
|-
|11
|43057017
|PLATE-COVER
|
|
|2
|-
|12
|HW0415
|BOLT-SHCS-3/8-16 X 3/4"
|
|
|8
|-
|13
|PT0624
|FITTING-ZERK
|
|
|2
|}
===<big>Hose Carrier Plate</big>===
[[File:BE-TS Hose Carrier Plate.png|alt=BE-TS Hose Carrier Plate|frameless|554x554px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43915018
|PLATE-HOSE CARRIER
|
|
|1
|-
|2
|PT0618
|BRACKET-FIXED END
|
|
|1
|-
|3
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
|4
|PT0617
|HOSE CARRIER
|
|''20 links required''
|3 FT
|-
|5
|PT0619
|BRACKET-MOVING END
|
|
|1
|-
|6
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|2
|-
|7
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|8
|HW0403
|BOLT-HHCS-3/8-16 X 1 1/4"
|
|''† See notes''
|2
|-
|9
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|6
|-
|10
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|11
|HW0005
|NUT-HEX-3/8-16
|
|
|4
|-
|12
|HC0262
|VALVE-CROSS PORT RELIEF
|
|''Includes cartridges''
|1
|-
|12a
|43846002
|REPLACEMENT CARTRIDGE
|
|''†† For Item 12 (Not shown)''
|2
|-
|13
|HW0308
|BOLT-HHCS-1/4-20 X 2 1/2"
|
|
|2
|-
|14
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|2
|-
|15
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|16
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|-
|17
|H1560
|ADAPTER-45 DEG-#8 JICM X #8 SAEM
|
|
|4
|-
|18
|E1329
|JUNCTION BOX-4" X 4" X 2"
|
|''PVC - Includes cover''
|1
|-
|19
|HW0212
|SCREW-RHMS-#10-24 X 1/2"
|
|
|4
|-
|20
|HW0102
|WASHER-FLAT-#10-SAE
|
|
|4
|-
|21
|E0623
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .250" to .375"''
|2
|-
|22
|E0622
|RESTRAINT-1/2"
|
|''Grip size .450" to .560"''
|1
|-
|23
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|''For Items 21 & 22 (Not shown)''
|3
|-
|24
|HW1076
|BOLT-FHSCS-3/8-16 X 1"
|
|''† See notes''
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Units built prior to February 2014 without extended reach option use (4) HW0403 mounting bolts.''

''†† Cartridges are for replacement only.''
|}

=== <big>'''Magnet Components ''(Rotary Actuator)'''''</big> ===

==== '''''<big>[Discontinued] Magnet Arm Configuration</big>''''' ====
[[File:BE-TS (Discontinued) Magnet Arm Configuration.png|alt=BE-TS (Discontinued) Magnet Arm Configuration|frameless|543x543px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41257014
|TIE PLATE-SWING ARM
|
|''All units''
|1
|-
|<nowiki>-</nowiki>
|41655008
|EXTENSION-ARM
|
|''BE-36 only (Not shown)''
|1
|-
|<nowiki>-</nowiki>
|43455001
|EXTENSION-ARM
|
|''BE-42 only (Not shown)''
|1
|-
|2
|HW0603
|BOLT-FHSCS-5/8-11 X 2"
|
|
|4
|-
|3
|HW0113
|WASHER-LOCK-5/8"
|
|
|4
|-
|4
|HW0010
|NUT-JAM-5/8-11
|
|
|4
|-
|5
|41655001
|CARRIER TUBE-MAGNET SWING SHAFT
|
|
|1
|-
|6
|HW0504
|BOLT-HHCS-1/2-13 X 2"
|
|
|6
|-
|7
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|6
|-
|8
|HW0110
|WASHER-LOCK-1/2"
|
|
|6
|-
|9
|HW0007
|NUT-HEX-1/2-13
|
|
|6
|-
|10
|41657006
|SHAFT-MAGNET SWING
|
|
|1
|-
|11
|41698001
|KEY-3/8" X 7/16"
|
|
|2
|-
|12
|N/A
|STOP-MAGNET SWING
|
|''† Dicontinued''
|1
|-
|13
|PT0430
|FLANGE BEARING-4 BOLT-1 1/2"
|
|
|2
|-
|14
|HW0513
|BOLT-HHCS-1/2-13 X 2 1/4"
|
|
|8
|-
|15
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|16
|-
|16
|HW0110
|WASHER-LOCK-1/2"
|
|
|8
|-
|17
|HW0007
|NUT-HEX-1/2-13
|
|
|8
|-
|18
|41655002
|PLATE-MAGNET MOUNTING
|
|
|2
|-
|19
|41257015
|BLOCK-TIGHTENER
|
|''2-piece item''
|1
|-
|20
|41257016
|BLOCK-FIXED
|
|''2-piece item''
|1
|-
|21
|HW0423
|BOLT-SHCS-3/8-16 X 3 1/2"
|
|
|4
|-
|22
|HW0006
|NUT-NILN-3/8-16
|
|
|4
|-
|23
|HW0806
|SET SCREW-3/8-16 X 2"
|
|''Replaces Swivel Head''
|4
|-
|24
|HW0424
|NUT-JAM-3/8-16
|
|
|4
|-
|25
|41657017
|INSULATOR-MAGNET MOUNT
|
|
|2
|-
|26
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|8
|-
|27
|41657008
|PAD-MAGNET SLIDE
|
|
|2
|-
|28
|HW0314
|BOLT-FHSCS-1/4-20 X 1/2"
|
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Refer to [https://tech.bhs1.com/index.php/(BE-TS)_Triple_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-401)#[Current]_Magnet_Arm_Configuration_(Rotary_Actuator) <nowiki>[Current] Magnet Arm Configuration (Rotary Actuator)</nowiki>] section for replacement / upgrade parts.''
|}

==== '''<big>''Magnet Pivot Stop (Rotary Actuator)''</big>''' ====
[[File:BE-TS Magnet Pivot Stop.png|alt=BE-TS Magnet Pivot Stop|frameless|547x547px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|N/A
|MAGNET PUSH/PULL ARM
|
|''† See notes''
|1
|-
|2
|43055010
|MAGNET MOUNT
|
|
|2
|-
|3
|PT0470
|BEARING-MAGNET PIVOT
|
|
|2
|-
|4
|HW0525
|BOLT-CARRIAGE-1/2-13 X 1 1/2"
|
|
|12
|-
|5
|HW0524
|BOLT-CARRIAGE-1/2-13 X 2"
|
|''†† Stop Plate location''
|4
|-
|6
|HW0110
|WASHER-LOCK-1/2"
|
|
|16
|-
|7
|HW0007
|NUT-HEX-1/2-13
|
|
|16
|-
|8
|43058009
|PLATE-ROTATION STOP
|
|
|2
|-
|9
|43058003
|SLEEVE-STOP
|
|
|2
|-
|10
|43058010
|SUPPORT-CABLE
|
|
|2
|-
|11
|PL0501
|GROMMET-1/2"
|
|
|2
|-
|12
|HW0523
|BOLT-HHCS-1/2-13 X 4"
|
|
|2
|-
|13
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|-
|14
|43057037
|INSULATOR-BOTTOM
|
|
|2
|-
|15
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|8
|-
|16
|41657008
|SLIDE-MAGNET
|
|
|2
|-
|17
|HW0314
|BOLT-FHSCS-1/4-20 X 1/2"
|
|
|4
|-
|18
|44558001
|PLATE-ROTATION STOP
|
|''†† Single compartment units only''
|2
|-
|REF
|43052014
|ADJUSTABLE PUSH-PULL ARM
|
|''Includes Items 19-23''
|A/R
|-
|19
|43055018
|ARM BASE
|
|
|1
|-
|20
|43055019
|MAGNET MOUNT
|
|
|2
|-
|21
|HW0523
|BOLT-HHCS-1/2-13 X 4"
|
|
|2
|-
|22
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|4
|-
|23
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† 1-Piece Arm no longer available. Must be replaced with Adjustable Arm.''
|-
| colspan="6" |''†† Single compartment Stop Plates require (1) additional 2" long Carriage Bolt each''
|}

==== <big>''[Current] Magnet Arm Configuration (Rotary Actuator)''</big> ====
[[File:BE-TS (Current) Magnet Arm Configuration.png|alt=BE-TS (Current) Magnet Arm Configuration|frameless|552x552px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|80252012
|MAGNET SWING STOP KIT
|
|''Includes Items 1 through 6''
|A/R
|-
|1
|43057029
|PLATE-STOP
|
|
|1
|-
|2
|43058003
|SLEEVE-STOP
|
|
|2
|-
|3
|43057030
|SUPPORT-CABLE
|
|
|2
|-
|4
|PL0501
|GROMMET-1/2"
|
|
|2
|-
|5
|HW0509
|BOLT-HHCS-1/2-13 X 4 1/2"
|
|
|2
|-
|6
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|-
|7
|44557003
|PLATE-STOP
|
|''† Single compartment units only''
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† For units equipped with Pivot Shaft. See [Current] Magnet Arm Configuration (Rotary Actuator) for units with Independent Magnet Pivot Bearings.''
|}

==== <big>''Magnet Mounting Hardware (Rotary Actuator)''</big> ====
[[File:BE-TS Magnet Mounting Hardware (Rotary Actuator).png|alt=BE-TS Magnet Mounting Hardware (Rotary Actuator)|frameless|554x554px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43032009
|MAGNET ASSEMBLY
|
|''Includes Items 1 through 12''
|A/R
|-
|1
|N/A
|ELECTROMAGNET-95VDC
|
|
|2
|-
|2
|E0314
|SENSOR-PROXIMITY-30MM
|
|
|2
|-
|3
|N/A
|GASKET-REAR
|
|''Discontinued - Not used''
|2
|-
|4
|41657002
|COVER-PROXIMITY SENSOR HOUSING
|
|''Rear''
|2
|-
|5
|HW1065
|SCREW-SHCS-#6-32 X 3/8"
|
|
|8
|-
|6
|HW1066
|WASHER-LOCK-#6
|
|
|8
|-
|7
|E0376
|INDICATOR LIGHT
|
|''† See notes''
|2
|-
|8
|E0335
|RECEPTACLE-5 PIN MALE
|
|''With 12" lead''
|2
|-
|9
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|2
|-
|10
|N/A
|GASKET-FRONT
|
|''Discontinued - Not used''
|2
|-
|11
|41657003
|COVER-PROXIMITY SENSOR HOUSING
|80252015
|''Front''
|2
|-
|12
|HW0138
|SCREW-FHSCS-#8-32 X 3/8"
|80252015
|
|8
|-
|13
|HW0433
|STUD-1/2-13 X 5"
|80252006
| rowspan="5" |''For units with Magnet Pivot Shaft only.''

''See [Discontinued] Magnet Arm Configuration for units built prior to 11/01/14''
|8
|-
|14
|HW0007
|NUT-HEX-1/2-13
|80252006
|8
|-
|15
|HW0112
|WASHER-FLAT-1/2"-SAE
|80252006
|40
|-
|16
|HW1002
|SPRING-1/2"
|80252006
|24
|-
|17
|HW0008
|NUT-NILN-1/2-13
|80252006
|8
|-
|18
|HW0514
|BOLT-HHCS-1/2-13 X 2 1/2"
|80252014
| rowspan="4" |''For units with independent Pivot Bearings only.''

''See [Current] Magnet Arm Configuration for units built 11/01/14 to present)''
|4
|-
|19
|HW1002
|SPRING-1/2"
|80252014
|4
|-
|20
|HW0112
|WASHER-FLAT-1/2"-SAE
|80252014
|8
|-
|21
|HW0007
|NUT-HEX-1/2-13
|80252014
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Extractors built or replacement magnets shipped prior to October 2021 used multi-piece indicator lights with replaceable bulb and lens and are no longer available. Current indicator light is a 1-piece LED assembly. Replacement of any multi-piece component requires replacing entire assembly with current, 1-piece indicator light.''
|}

=== '''''Magnet Cords (Rotary Actuator)''''' ===
[[File:BE-TS Magnet Cords.png|alt=BE-TS Magnet Cords|frameless|555x555px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E1105
|JUNCTION BOX-4" X 2" X 2"
|
|''Weather proof box''
|1
|-
|2
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
|3
|E1106
|COVER-JUNCTION BOX
|
|''Weather proof with gasket''
|1
|-
|4
|E0333
|RECEPTACLE-9 PIN MALE
|
|''With 12" lead''
|1
|-
|5
|E0608-1
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .450" to .560"''
|2
|-
|6
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|3
|-
|7
|E0334
|CORD-5 PIN FEMALE
|
|''With 36" lead''
|2
|-
|8
|E0332
|CORD-9 PIN FEMALE-90 DEG
|
|''With 36" lead''
|1
|-
|9
|PL0501
|GROMMET-1/2"
|
|
|1
|-
|10
|41657013-2
|PLATE-PANEL MOUNTING
|
|''With single cable hole''
|1
|-
|11
|E0334-6
|CORD-5 PIN FEMALE
|
|''With 72" lead''
|2
|-
|12
|43057038-2
|PLATE-PANEL MOUNTING
|
|''With dual cable holes''
|1
|}
'''''<big>Magnet Panel Mounting (Rotary Actuator)</big>'''''

[[File:BE-TS Panel Mounting (Rotary Actuator).png|alt=BE-TS Panel Mounting (Rotary Actuator)|frameless|551x551px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43057021
|PLATE-STIFFENER
|
|
|1
|-
|2
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|12
|-
|3
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|''Not shown''
|24
|-
|4
|HW0107
|WASHER-LOCK-3/8"
|
|
|12
|-
|5
|HW0005
|NUT-HEX-3/8-16
|
|
|12
|-
|6
|41637001
|PANEL-COMPONENT MOUNTING
|
|
|1
|-
|7
|HW0325
|BOLT-5/16-18 X 1 3/4"-PAN HEAD
|
|
|4
|-
|8
|N/A
|INSULATOR-THREADED FEMALE
|
|''Discontinued''
|4
|-
|9
|HW0106
|WASHER-FLAT-5/16"-SAE
|
|
|8
|-
|10
|HW0326
|NUT-NILN-5/16-18
|
|
|8
|-
|11
|E1016
|FUSE HOLDER
|
|
|1
|-
|12
|HW0130
|SCREW-RHMS-#8-32 X 1/2"
|
|
|1
|-
|13
|HW0133
|WASHER-FLAT-#8-SAE
|
|
|1
|-
|14
|HW0132
|NUT-NILN-#8-32
|
|
|1
|-
|15
|E0325
|FUSE-7AMP-250VAC
|
|''FLM-7 or FNM-7''
|1
|-
|16
|PL0307
|INSULATOR-MALE STUD
|
|
|4
|}
'''''<big>Magnet Extractor Electrical Panel (Rotary Actuator)</big>'''''

[[File:BE-TS Magnet Extractor Electrical Panel (Rotary Actuator).png|alt=BE-TS Magnet Extractor Electrical Panel (Rotary Actuator)|frameless|551x551px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41637001
|PANEL-COMPONENT MOUNTING
|
|
|1
|-
|2
|41637002
|WIRE WAY
|
|
|2
|-
|3
|41637003
|WIRE WAY
|
|
|1
|-
|4
|41637004
|TRACK-TERMINAL BLOCK MOUNTING
|
|
|1
|-
|5
|41637005
|TRACK-TERMINAL BLOCK MOUNTING
|
|
|1
|-
|6
|HW0130
|SCREW-RHMS-#8-32 X 1/2"
|
|
|10
|-
|7
|HW0132
|WASHER-FLAT-#8-SAE
|
|
|10
|-
|8
|HW0133
|NUT-NILN-#8-32
|
|''Not shown''
|16
|-
|9
|E1020
|TERMINAL BLOCK
|
|
|12
|-
|10
|E1040
|END BARRIER
|
|
|2
|-
|11
|E1330
|END ANCHOR
|
|
|4
|-
|12
|E1009
|RECTIFIER-FULL WAVE BRIDGE
|
|
|2
|-
|13
|HW0135
|SCREW-RHMS-#8-32 X 3/4"
|
|
|2
|-
|14
|E1313
|SOCKET-RELAY-8 PIN
|
|
|2
|-
|15
|HW0139
|SCREW-RHMS-#8-32 X 1 1/4"
|
|
|4
|-
|16
|E0331
|RELAY-DPDT-110VAC
|
|''with Indicator Light''
|2
|}

=== <big>'''Swing Arm Stop (Rotary Actuator)'''</big> ===
[[File:BE-TS Swing Arm Stop (Rotary Actuator).png|alt=BE-TS Swing Arm Stop (Rotary Actuator)|frameless|545x545px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43055007
|MOUNT-STOP-SWING ARM
|
|''† See notes''
|2
|-
| rowspan="2" |2
|43057024
|STOP-SWING ARM
|
|''BE-24''
|4
|-
|43057023
|STOP-SWING ARM
|
|''BE-36 & BE-42''
|4
|-
|3
|HW0304
|BOLT-HHCS-1/4-20 X 1 1/2"
|
|
|4
|-
|4
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|8
|-
|5
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|6
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|7
|HW0403
|BOLT-HHCS-3/8-16 X 1 1/4"
|
|
|4
|-
|8
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|9
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† See [https://tech.bhs1.com/index.php/(BE-TS)_Triple_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-401)#Vacuum_Swing_Arm_Stop_(Rotary_Actuator) Vacuum Swing Arm Stop (Rotary Actuator)] section for single compartment stop mount and stop.''
|}

=== '''<big>Vacuum Extended Reach (Rotary Actuator)</big>''' ===
[[File:BE-TS Vacuum Extended Reach (Rotary Actuator).png|alt=BE-TS Vacuum Extended Reach (Rotary Actuator)|frameless|536x536px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41257014
|TIE PLATE-SWING ARM
|
|''All units''
|1
|-
|<nowiki>-</nowiki>
|41655008
|EXTENSION-ARM
|
|''BE-36 only (Not shown)''
|1
|-
|<nowiki>-</nowiki>
|43455001
|EXTENSION-ARM
|
|''BE-42 only (Not shown)''
|1
|-
|2
|HW0504
|BOLT-HHCS-1/2-13 X 2"
|
|
|6
|-
|3
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|6
|-
|4
|HW0110
|WASHER-LOCK-1/2"
|
|
|6
|-
|5
|HW0007
|NUT-HEX-1/2-13
|
|
|6
|-
|6
|P0301-1
|HOSE-COIL-VACUUM
|
|
|1
|-
|7
|41257035
|STANDOFF
|
|
|2
|-
|8
|HW1072
|RESTRAINT-HOSE
|
|
|2
|-
|9
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|2
|-
|10
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|11
|HW0318
|BOLT-SHCS-1/4-20 X 1 1/2"
|
|
|2
|-
|12
|HW0302
|BOLT-HHCS-1/4-20 X 3/4"
|
|
|1
|-
|13
|HW0312
|SCREW-SHSS-1/4-20 X 1"-CUP POINT
|
|
|1
|}
[[File:BE-TS Vacuum Extended Reach (Rotary Actuator) 2.png|alt=BE-TS Vacuum Extended Reach (Rotary Actuator)|frameless|547x547px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41255005
|ARM-EXTENSION-VACUUM
|
|
|1
|-
|2
|HC0416
|CYLINDER-EXTENDED REACH-VACUUM
|
|''2 1/2" X 12" Cylinder''
|1
|-
|3
|H1578
|ADAPTER-90 DEG-#6 JICM X #6 MNPT
|
|
|2
|-
|4
|41257031
|PIN-CLEVIS END
|
|
|1
|-
|5
|00197036
|PIN-ROD END
|
|
|1
|-
|6
|HW1058
|PIN-HITCH
|
|
|4
|}
[[File:BE-TS Vacuum Extended Reach (Rotary Actuator) 3.png|alt=BE-TS Vacuum Extended Reach (Rotary Actuator) 3|frameless|541x541px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41255004
|HOUSING-EXTENDED REACH-VACUUM
|
|
|1
|-
|2
|41257030
|PLATE-END
|
|
|1
|-
|3
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|4
|-
|4
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|8
|-
|5
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|6
|HW0005
|NUT-HEX-3/8-16
|
|
|4
|-
|7
|41258002
|PLATE-BEARING
|80258001
|''Side''
|2
|-
|8
|41258005
|PLATE-SHIM
|80258001
|''Side''
|2
|-
|9
|41258003
|PLATE-BEARING
|80258001
|''Upper / lower''
|2
|-
|10
|41258004
|PLATE-SHIM
|80258001
|''Upper / lower''
|2
|-
|11
|HW0812
|SCREW-SHSS-1/4-20 X 5/8"-HALF DOG
|
|
|28
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|28
|}

=== '''<big>Extended Reach (Rotary Actuator)</big>''' ===
[[File:BE-TS Extended Reach Rotary Actuator.png|alt=BE-TS Extended Reach Rotary Actuator|frameless|548x548px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43046001
|ROTARY ACTUATOR
|
|
|1
|-
|2
|80000002
|ROTARY ACTUATOR BASE ASSEMBLY
|
|''Without Actuator''
|1
|-
|2A
|N/A
|VERTICAL CARRIER PLATE-OUTER
|
|''Included with 80000002''
|2
|-
|2B
|N/A
|VERTICAL CARRIER PLATE-INNER
|
|''Included with 80000002''
|1
|-
|2C
|N/A
|CARRIER BASE PLATE
|
|''Included with 80000002''
|1
|-
|3
|HW1070
|PIN-PULL DOWEL-5/8" X 1 1/2"
|
|
|2
|-
|4
|HW0508
|BOLT-SHCS-1/2-13 X 3/4"
|
|
|3
|-
|5
|HW1045
|PIN-PULL DOWEL-3/8" X 1 1/2"
|
|''Included with 80000002''
|6
|-
|6
|HW0412
|BOLT-SHCS-3/8-16 X 1 1/4"
|
|''Included with 80000002''
|12
|-
|7
|H0010
|FITTING-BULKHEAD-3/4-16 X #4 FNPT
|
|
|4
|-
|8
|H1579
|ADAPTER-90 DEG-#6 JICM X #4 MNPT
|
|
|4
|}
[[File:BE-TS Extended Reach Rotary Actuator 2.png|alt=BE-TS Extended Reach Rotary Actuator |frameless|535x535px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|PT0634
|BRACKET-MALE END
|
|''Sols as a set''
|1
|-
|2
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|4
|-
|3
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|10
|-
|4
|HW0103
|WASHER-LOCK-1/4"
|
|
|6
|-
|5
|HW0002
|NUT-HEX-1/4-20
|
|
|6
|-
|6
|PT0627
|HOSE CARRIER
|
|''14 links required''
|39"
|-
|7
|PT0634
|BRACKET-FEMALE END
|
|''Sols as a set''
|1
|-
|8
|HC0262
|VALVE-CROSS PORT RELIEF
|
|
|1
|-
|8a
|43046003
|REPLACEMENT CARTRIDGE
|
|''† For Item 8 (Not shown)''
|2
|-
|9
|HW0308
|BOLT-HHCS-1/4-20 X 2 1/2"
|
|
|2
|-
|10
|H1546
|ADAPTER-#6 JICM X #8 SAEM
|
|
|2
|-
|11
|H1617
|ADAPTER-45 DEG-#6 JICM X #8 SAEM
|
|
|2
|-
|12
|HC0237
|VALVE-SEQUENCING
|
|
|1
|-
|12a
|43046005
|REPLACEMENT CARTRIDGE
|
|''† For Item 12 (Not shown)''
|A/R
|-
|13
|HW0317
|BOLT-HHCS-1/4-20 X 3 1/2"
|
|
|2
|-
|14
|H1560
|ADAPTER-45 DEG-#8 JICM X #8 SAEM
|
|
|4
|-
|15
|H1600
|ADAPTER-90 DEG-#6 JICM X #8 SAEM
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Cartridges are for replacement only''
|}

=== '''<big>Magnet Extended Reach (Rotary Actuator)</big>''' ===
[[File:BE-TS Magnet Extended Reach (Rotary Actuator).png|alt=BE-TS Magnet Extended Reach (Rotary Actuator)|frameless|548x548px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43055011
|ARM-EXTENSION-MAGNET
|
|
|1
|-
|2
|HC0415
|CYLINDER-EXTENDED REACH-MAGNET
|
|''2 1/2" X 8" Cylinder''
|1
|-
|3
|H1578
|ADAPTER-90 DEG-#6 JICM X #6 MNPT
|
|
|2
|-
|4
|43057042
|PIN-CLEVIS END
|
|
|1
|-
|5
|43057043
|PIN-ROD END
|
|
|1
|-
|6
|HW1132
|RETAINING RING-EXTERNAL-3/4" I.D.
|
|
|4
|-
|7
|HW1043
|CLAMP-CYLINDER
|
|
|2
|-
|8
|43057044-2
|SUPPORT-CABLE
|
|
|2
|-
|9
|PL0501
|GROMMET-1/2" I.D.
|
|
|4
|-
|10
|43058019
|SUPPORT-CABLE-BAND CLAMP
|
|
|2
|-
|11
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|12
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|}
[[File:BE-TS Magnet Extended Reach (Rotary Actuator) 2.png|alt=BE-TS Magnet Extended Reach (Rotary Actuator) |frameless|543x543px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43055012
|HOUSING-EXTENDED REACH-MAGNET
|
|
|1
|-
|2
|50057008
|PLATE-END
|
|
|1
|-
|3
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|4
|-
|4
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|8
|-
|5
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|6
|HW0005
|NUT-HEX-3/8-16
|
|
|4
|-
|7
|43058013
|PLATE-BEARING-SIDE
|
|
|2
|-
|8
|43058016
|PLATE-SHIM-SIDE
|
|
|2
|-
|9
|43058014
|PLATE-BEARING-UPPER/LOWER
|
|
|2
|-
|10
|43058015
|PLATE-SHIM-UPPER/LOWER
|
|
|2
|-
|11
|HW0812
|SCREW-SHSS-1/4-20 X 5/8"-HALF DOG
|
|
|24
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|24
|}

=== '''<big>Extended Reach End Plate</big>''' ===
[[File:BE-TS Extended Reach End Plate.png|alt=BE-TS Extended Reach End Plate|frameless|552x552px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|N/A
|CARRIER SHAFT-EXTRACTOR ARM
|
|''† 3-Hole version''
|A/R
|-
|2
|PT0413
|COLLAR-SHAFT-3"
|
|
|4
|-
|3
|50057009
|PLATE-END-3 HOLE
|
|''Replacement part only''
|4
|-
|4
|50057010
|SHIM-END PLATE
|
|''†† See notes''
|A/R
|-
|5
|HW1076
|BOLT-FHSCS-3/8-16 X 1"
|
|
|12
|-
|6
|43057045
|CARRIER SHAFT-EXTRACTOR ARM
|
|''1-Hole version''
|2
|-
|7
|43017076
|PLATE-END-1 HOLE
|
|
|4
|-
|8
|HW0603
|BOLT-FHSCS-5/8-11 X 2"
|
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† 3-Hole Carrier Shaft no longer available. Must replace 3-Hole shaft with current, 1-Hole version along with new ennd plates & hardware.''
|-
| colspan="6" |''†† Shim quantity varies due to manufacturing tolerances.''
|}

=== '''<big>Carrier Shafts & Bearings</big>''' ===
[[File:BE-TS Carrier Shafts & Bearings (Helical Actuator).png|alt=BE-TS Carrier Shafts & Bearings (Helical Actuator)|frameless|543x543px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43057045
|CARRIER SHAFT-EXTRACTOR ARM
|
|''† See notes''
|2
|-
|2
|43054007
|BEARING-EXTRACTOR ARM CARRIER
|80252002
|
|4
|-
|3
|HW0412
|BOLT-SHCS-3/8-16 X 1 1/4"
|80252002
|
|16
|-
|4
|PT0413
|COLLAR-SHAFT-3"
|
|
|4
|-
|5
|50057010
|SHIM-END PLATE
|
|
|A/R
|-
|6
|43017076
|PLATE-END-1 HOLE
|
|
|4
|-
|7
|HW0603
|BOLT-FHSCS-5/8-11 X 2"
|
|
|4
|-
|8
|PT0624
|FITTING-ZERK
|80252002
|''Not shown''
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† See [https://tech.bhs1.com/index.php/(BE-TS)_Triple_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-401)#Extended_Reach_End_Plate Extended Reach End Plate] section for Extended Reach equipped units.''
|}

=== '''<big>Drive Nut Assembly (Helical Actuator)</big>''' ===
[[File:BE-TS Drive Nut Assembly (Helical Actuator).png|alt=BE-TS Drive Nut Assembly (Helical Actuator)|frameless|600x600px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43054006
|DRIVE NUT ASSEMBLY
|80252003
|
|1
|-
|2
|HW0426
|BOLT-SHCS-3/8-16 X 5 1/2"
|80252003
|''† See notes''
|4
|-
|3
|HW0108
|WASHER-FLAT-3/8"-SAE
|80252003
|''† See notes''
|4
|-
|4
|HW0006
|NUT-NILN-3/8-16
|80252003
|''† See notes''
|4
|-
|5
|PT0624
|FITTING-ZERK
|80252003
|
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† It is recommended to replce mounting hardware when replacing Drive Nut Assembly.''
|}

=== '''<big>Swing Arms & Actuator (Helical Actuator)</big>''' ===

==== '''''<big>[Discontinued] Helical Actuator</big>''''' ====
[[File:BE-TS Swing Arms & Actuator (Helical Actuator).png|alt=BE-TS [Discontinued] Swing Arms & Actuator (Helical Actuator)|frameless|557x557px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|N/A
|HELICAL ACTUATOR
|
|''† See notes''
|1
|-
|2
|43057046
|ACTUATOR BASE PLATE
|
|
|1
|-
|3
|43058022
|SPACER-ACTUATOR
|
|
|4
|-
|4
|HW0725
|BOLT-HHCS-3/4-16 X 4-3/4"-GR8
|
|
|4
|-
|5
|HW0066
|NUT-JAM-3/4-16-GR8
|
|
|4
|-
|6
|43055013
|SWING ARM-LHS
|
| rowspan="6" |''†† See notes''
|1
|-
|7
|HW0620
|BOLT-HHCS-5/8-11 X 1-1/4"
|
|6
|-
|8
|HW0113
|WASHER-LOCK-5/8"
|
|6
|-
|9
|43055014
|SWING ARM-RHS
|
|1
|-
|10
|HW0502
|BOLT-HHCS-1/2-13 X 1-1/4"
|
|6
|-
|11
|HW0110
|WASHER-LOCK-1/2"
|
|6
|-
|12
|43042008
|3/8" TUBE X #6 JIC HARD-PIPE
|
|
|1
|-
|13
|43042010
|3/8" TUBE X #6 JIC HARD-PIPE, LONG
|
|
|1
|-
|14
|H1619
|ADAPTER-90 DEG-#6 JICM X #4 SAEM
|
|
|2
|-
|15
|H0010
|FITTING-H-BULKHEAD-1/4 FNPT
|
|
|2
|-
|16
|H1504
|ADAPTER-#6 JICM X #4 NPTM
|
|
|2
|-
|17
|HW1082
|CLAMP-HOSE
|
|
|1
|-
|18
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Discontinued Helical Actuator no longer available. Must replace with current Helical Actuator Retro Kit 80252032. See [Current] Helical Actuator.''

''†† Swing arms manufactured prior to January 2022 use 10 bolts & washers per Swing Arm.''
|}

==== '''''<big>[Current] Helical Actuator</big>''''' ====
[[File:BE-TS (Current) Swing Arms & Actuator (Helical Actuator).png|alt=BE-TS (Current) Swing Arms & Actuator (Helical Actuator)|frameless|544x544px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|N/A
|43052020
|HELICAL ACTUATOR ASSEMBLY
|
|''Includes Items 1 through 17''
|1
|-
|1
|HC0180
|HELICAL ACTUATOR
|80252032
|
|1
|-
|2
|43057046
|ACTUATOR BASE PLATE
|
|
|1
|-
|3
|43058022
|SPACER-ACTUATOR
|
|
|4
|-
|4
|HW0725
|BOLT-HHCS-3/4-16 X 4-3/4"-GR8
|
|
|4
|-
|5
|HW0066
|NUT-JAM-3/4-16-GR8
|
|
|4
|-
|6
|43055013
|SWING ARM-LHS
|
|
|1
|-
|7
|HW0620
|BOLT-HHCS-5/8-11 X 1-1/4"
|
|
|6
|-
|8
|HW0113
|WASHER-LOCK-5/8"
|
|
|6
|-
|9
|43055014
|SWING ARM-RHS
|
|
|1
|-
|10
|HW0502
|BOLT-HHCS-1/2-13 X 1-1/4"
|
|
|6
|-
|11
|HW0110
|WASHER-LOCK-1/2"
|
|
|6
|-
|12
|43042011
|3/8" TUBE X #6 JIC HARD-PIPE, 90 DEG
|80252032
|''† See notes''
|1
|-
|13
|43042012
|3/8" TUBE X #6 JIC HARD-PIPE, SHORT
|80252032
|''† See notes''
|1
|-
|14
|H1619
|ADAPTER-90 DEG-#6 JICM X #4 SAEM
|80252032
|
|2
|-
|15
|H0010
|FITTING-H-BULKHEAD-1/4 FNPT
|
|
|2
|-
|16
|H1504
|ADAPTER-#6 JICM X #4 NPTM
|80252032
|
|1
|-
|17
|H1691
|ADAPTER-45 DEG-#6 JICM X #4 NPTM
|80252032
|''† See notes''
|1
|-
|18
|HW1082
|CLAMP-HOSE
|
|
|1
|-
|19
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Hard-Pipes and 45 degree adapter required if replacing discontinued actuator with current Actuator Kit Part # 80252032 required for discontinued actuator replacement.''
|}

=== '''<big>Swing Arm Stops & Tie Plate</big>''' ===
[[File:BE-TS Swing Arm Stops & Tie Plate (Helical Actuator).png|alt=BE-TS Swing Arm Stops & Tie Plate (Helical Actuator)|frameless|545x545px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43057050
|TIE PLATE-HELICAL SWING ARM
|
|
|1
|-
|2
|HW0603
|BOLT-FHSCS-5/8-11 X 2"
|
|
|4
|-
|3
|HW0113
|WASHER-LOCK-5/8"
|
|
|4
|-
|4
|HW0010
|NUT-JAM-5/8-11
|
|
|4
|-
|5
|43057052
|STOP-POLY-SWING ARM
|
|''† See notes''
|4
|-
|6
|HW0441
|BOLT-FHSCS-3/8-16 X 1-1/2"
|
|
|4
|-
|7
|HW0031
|NUT-LOCK-3/8-16, DEFORMED THREAD
|
|''† † See notes''
|4
|-
|8
|44555002
|SWING ARM STOP
|
|''Single compartment use only''
|A/R
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Replacement Poly Stop design updated from Square to Round. Stop Spacers not required with current, Round-Style Stops.''
|-
| colspan="6" |''† † Deformed Thread Lock Nut replaces Acorn Nut and Split Lock Washer used previously.''
|}

=== '''<big>Push/Pull Arm Mounting (Helical Actuator)</big>''' ===
[[File:BE-TS Push-Pull Arm Mounting.png|alt=BE-TS Push-Pull Arm Mounting (Helical Actuator)|frameless|542x542px]]
{| class="wikitable"
! rowspan="2" |ITEM
! rowspan="2" |BHS PART NUMBER
! rowspan="2" |DESCRIPTION
! rowspan="2" |REF. KIT NO.
! rowspan="2" |NOTES
! colspan="3" |NO. REQ
|-
!BE-24
!BE-36
!BE-42
|-
| rowspan="2" |1
|41655008
|EXTENSION-ARM
|
|''†BE-36 units only''
|<nowiki>-</nowiki>
|1
|<nowiki>-</nowiki>
|-
|43455001
|EXTENSION-ARM
|
|''†BE-42 units only''
|<nowiki>-</nowiki>
|<nowiki>-</nowiki>
|1
|-
|2
|HW0504
|BOLT-HHCS-1/2-13 X 2"
|
|
|6
| colspan="2" |12
|-
|3
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|12
| colspan="2" |24
|-
|4
|HW0110
|WASHER-LOCK-1/2"
|
|
|6
| colspan="2" |12
|-
|5
|HW0007
|NUT-HEX-1/2-13
|
|
|6
| colspan="2" |12
|-
! colspan="8" |NOTES
|-
| colspan="8" |''† BE-24 units do not utilize an Arm Extension.''
|}

=== '''<big>Vacuum Extractor Arm (Helical Actuator)</big>''' ===

==== '''''<big>Non-Pivoting Vacuum Cup Arm (Helical Actuator)</big>''''' ====
[[File:BE-TS Non-Pivoting Vacuum Cup Arm (Helical Actuator).png|alt=BE-TS Non-Pivoting Vacuum Cup Arm (Helical Actuator)|frameless|578x578px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HW0428
|STUD-VACUUM-3/8-16 X 5"
|HW-KIT-2
|
|8
|-
|2
|HW0108
|WASHER-FLAT-3/8"-SAE
|HW-KIT-2
|
|40
|-
|3
|HW1001
|SPRING-3/8"
|HW-KIT-2
|
|24
|-
|4
|HW0006
|NUT-NILN-3/8-16
|HW-KIT-2
|
|8
|-
|5
|HW0424
|NUT-JAM-3/8-16
|HW-KIT-2
|
|8
|-
|6
|P0402
|HOSE BARB-1/4" X #4 MNPT-BRASS
|
|
|2
|-
|REF
|43052014
|ADJUSTABLE PUSH-PULL ARM
|
|''Includes Items 7 through 11''
|A/R
|-
|7
|43055018
|ARM BASE
|
|
|1
|-
|8
|43055019
|VACUUM CUP MOUNT
|
|
|2
|-
|9
|HW0523
|BOLT-HHCS-1/2-13 X 4"
|
|
|2
|-
|10
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|4
|-
|11
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|}

==== '''''<big>Pivoting Vacuum Cup Arm (Helical Actuator)</big>''''' ====
[[File:BE-TS Pivoting Vacuum Cup Arm (Helical Actuator).png|alt=BE-TS Pivoting Vacuum Cup Arm (Helical Actuator)|frameless|525x525px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43052014
|ADJUSTABLE PUSH-PULL ARM
|
|''Includes Items 1 through 5''
|A/R
|-
|1
|43055018
|ARM BASE
|
|
|1
|-
|2
|43055019
|VACUUM CUP MOUNT
|
|
|2
|-
|3
|HW0523
|BOLT-HHCS-1/2-13 X 4"
|
|
|2
|-
|4
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|4
|-
|5
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|-
|6
|43055020
|MOUNT-PIVOT-VACUUM CUP
|
|
|2
|-
|7
|PT0470
|BEARING-PIVOT
|
|
|2
|-
|8
|HW0525
|BOLT-CARRIAGE-1/2-13 X 1 1/2"
|
|
|12
|-
|9
|HW0524
|BOLT-CARRIAGE-1/2-13 X 2"
|
|
|4
|-
|10
|HW0110
|WASHER-LOCK-1/2"
|
|
|16
|-
|11
|HW0008
|NUT-HEX-1/2-13
|
|
|16
|-
|12
|43058009
|PLATE-ROTATION STOP
|
|
|2
|-
|13
|43058003
|SLEEVE-STOP
|
|
|2
|-
|14
|43058010
|SUPPORT-CABLE
|
|
|2
|-
|15
|E0622
|RESTRAINT-1/2"
|
|''Grip size .450" to .560"''
|4
|-
|16
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|4
|-
|17
|HW0523
|BOLT-HHCS-1/2-13 X 4"
|
|
|2
|-
|18
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|-
|19
|43037002-2
|SUPPORT-CABLE RESTRAINT
|
|
|2
|-
|20
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|4
|-
|21
|P0506
|ELBOW-STR-90 DEG-#4 NPT-BRASS
|
|
|2
|-
|22
|P0402
|HOSE BARB-1/4" X #4 MNPT-BRASS
|
|
|2
|-
|23
|43057056-2
|BRACKET-HOSE SUPPORT
|
|
|2
|-
|24
|PL0507
|GROMMET-5/8" I.D.
|
|
|2
|-
|25
|P0302
|HOSE-VACUUM-1/4" I.D.
|
|''2 pieces at 48" each''
|96"
|-
|26
|HW0443
|BOLT-HHCS-3/8-16 X 3-1/2"
|HW-KIT-3
|
|8
|-
|27
|HW1001
|SPRING-3/8"
|HW-KIT-3
|
|16
|-
|28
|HW0108
|WASHER-FLAT-3/8"-SAE
|HW-KIT-3
|
|32
|-
|29
|HW0424
|NUT-JAM-3/8-16
|HW-KIT-3
|
|4
|}

=== '''<big>Vacuum Cup Rotation Stop (Helical Actuator)</big>''' ===
[[File:BE-TS Vacuum Cup Rotation Stop (Helical Actuator).png|alt=BE-TS Vacuum Cup Rotation Stop (Helical Actuator)|frameless|583x583px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|445558001
|PLATE-ROTATION STOP
|
|''† Single compartment units only''
|2
|-
|2
|HW0525
|BOLT-CARRIAGE-1/2-13 X 1 1/2"
|
|
|2
|-
|3
|HW0524
|BOLT-CARRIAGE-1/2-13 X 2"
|
|
|6
|-
|4
|HW0110
|WASHER-LOCK-1/2"
|
|
|8
|-
|5
|HW0008
|NUT-HEX-1/2-13
|
|
|8
|}

=== '''<big>Vacuum Components (Helical Actuator)</big>''' ===
[[File:BE-TS Vacuum Components (Helical Actuator).png|alt=BE-TS Vacuum Components (Helical Actuator)|frameless|543x543px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43058021
|STIFFENER PLATE-HELICAL SWING ARM
|
|
|2
|-
|2
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|12
|-
|3
|HW0108
|WASHER-FLAT-3/8"
|
|
|24
|-
|4
|HW0107
|WASHER-LOCK-3/8"
|
|
|12
|-
|5
|HW0005
|NUT-HEX-3/8-16
|
|
|12
|-
|6
|P0005
|PUMP-VACUUM
|
|
|1
|-
|7
|P0207
|VALVE-VACUUM RELEASE
|
|
|2
|-
|8
|P0208
|FILTER-HI FLOW
|
|
|3
|-
|9
|H0011
|NIPPLE-#4 X 2"-BRASS
|
|
|1
|-
|10
|P0502
|TEE-#4 FNPT-BRASS
|
|
|1
|-
|11
|P0506
|ELBOW-STR-90 DEG-#4 NPT-BRASS
|
|
|4
|-
|12
|P0503
|NIPPLE-#4 NPT-BRASS
|
|
|2
|-
|13
|P0402
|HOSE BARB-1/4" X #4 MNPT-BRASS
|
|
|6
|-
|14
|P0111
|FILTER-VACUUM-IN-LINE
|
|
|2
|-
|15
|HW0206
|SCREW-RHMS-#10-32 X 3/4"
|
|
|4
|-
|16
|43037014-2
|BRACKET-CABLE RESTRAINT
|
|
|1
|-
|17
|E0622
|RESTRAINT-1/2"
|
|''Grip size .450" to .560"''
|2
|-
|18
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|2
|-
|19
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
|20
|E0611
|JUNCTION BOX-4" X 2" X 2"
|
|
|1
|-
|21
|E0612
|COVER-JUNCTION BOX
|
|
|1
|-
|22
|E0624
|CONNECTOR-1/2"
|
|''Includes Lock Nut''
|1
|-
|23
|HW0212
|SCREW-RHMS-#10-24 X 1/2"
|
|
|2
|}

=== '''<big>Magnet Arm (Helical Actuator)</big>''' ===
[[File:BE-TS Magnet Arm (Helical Actuator).png|alt=BE-TS Magnet Arm (Helical Actuator)|frameless|551x551px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43052014
|ADJUSTABLE PUSH-PULL ARM
|
|''Includes Items 1 through 5''
|A/R
|-
|1
|43055018
|ARM BASE
|
|
|1
|-
|2
|43055019
|VACUUM CUP MOUNT
|
|
|2
|-
|3
|HW0523
|BOLT-HHCS-1/2-13 X 4"
|
|
|2
|-
|4
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|4
|-
|5
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|-
|6
|43055016
|MOUNT-PIVOT-MAGNET
|
|
|2
|-
|7
|PT0470
|BEARING-PIVOT
|
|
|2
|-
|8
|HW0525
|BOLT-CARRIAGE-1/2-13 X 1 1/2"
|
|
|12
|-
|9
|HW0524
|BOLT-CARRIAGE-1/2-13 X 2"
|
|
|4
|-
|10
|HW0110
|WASHER-LOCK-1/2"
|
|
|16
|-
|11
|HW0008
|NUT-HEX-1/2-13
|
|
|16
|-
|12
|43058009
|PLATE-ROTATION STOP
|
|
|2
|-
|13
|43058003
|SLEEVE-STOP
|
|
|2
|-
|14
|43058010
|SUPPORT-CABLE
|
|
|2
|-
|15
|HW0523
|BOLT-HHCS-1/2-13 X 4"
|
|
|2
|-
|16
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|-
|17
|E0622
|RESTRAINT-1/2"
|
|''Grip size .450" to .560"''
|2
|-
|18
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|2
|-
|19
|43037002-2
|SUPPORT-CABLE RESTRAINT
|
|
|2
|-
|20
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|4
|-
|21
|E0334-6'
|CORD-5 PIN FEMALE
|
|''With 72" lead''
|2
|-
|22
|E1041
|WIRE LOOM-SPIRAL-3/8"
|
|''2 pieces at 24" each''
|48"
|-
|23
|PL0501
|GROMMET-1/2" I.D.
|
|
|2
|-
|24
|43057037
|INSULATOR-BOTTOM
|
|
|2
|-
|25
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|8
|-
|26
|41657008
|SLIDE-MAGNET
|
|
|2
|-
|27
|HW0314
|BOLT-FHSCS-1/4-20 X 1/2"
|
|
|4
|}

=== '''<big>Magnet Assembly (Helical Actuator)</big>''' ===
[[File:BE-TS Magnet Assembly (Helical Actuator).png|alt=BE-TS Magnet Assembly (Helical Actuator)|frameless|548x548px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43032009
|MAGNET ASSEMBLY
|
|''Includes Items 1 through 12''
|A/R
|-
|1
|N/A
|ELECTROMAGNET-95VDC
|
|
|2
|-
|2
|E0314
|SENSOR-PROXIMITY-30MM
|
|
|2
|-
|3
|41657002
|COVER-PROXIMITY SENSOR HOUSING
|
|''Rear''
|2
|-
|4
|HW1065
|SCREW-SHCS-#6-32 X 3/8"
|
|
|8
|-
|5
|HW1066
|WASHER-LOCK-#6
|
|
|8
|-
|6
|E0335
|RECEPTACLE-5 PIN MALE
|
|''With 12" lead''
|2
|-
|7
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|2
|-
|8
|E0376
|INDICATOR LIGHT
|
|''† See notes''
|2
|-
|9
|41657003
|COVER-PROXIMITY SENSOR HOUSING
|80252015
|''Front''
|2
|-
|10
|HW0138
|SCREW-FHSCS-#8-32 X 3/8"
|80252015
|
|8
|-
|11
|HW0514
|BOLT-HHCS-1/2-13 X 2 1/2"
|80252014
|
|4
|-
|12
|HW1002
|SPRING-1/2"
|80252014
|
|4
|-
|13
|HW0112
|WASHER-FLAT-1/2"-SAE
|80252014
|
|8
|-
|14
|HW0007
|NUT-HEX-1/2-13
|80252014
|
|4
|-
|15
|E0336
|METAL OXIDE VARISTOR
|
|''Not shown''
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Extractors built or replacement magnets shipped prior to October 2021 used Multi-Piece Indicator Lights with replaceable bulb and lens and are no longer available. Current Indicator Light is a 1-Piece LED assembly. Replacement of any Multi-Piece component requires replacing entire assembly with current, 1-Piece Indicator Light.''
|}

=== '''<big>Magnet Components (Helical Actuator)</big>''' ===
[[File:BE-TS Magnet Components (Helical Actuator).png|alt=BE-TS Magnet Components (Helical Actuator)|frameless|534x534px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43058021
|STIFFENER PLATE-HELICAL SWING ARM
|
|
|1
|-
|2
|43057051-2
|STIFFENER-MAGNET-HELICAL SWING ARM
|
|
|1
|-
|3
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|12
|-
|4
|HW0108
|WASHER-FLAT-3/8"
|
|
|24
|-
|5
|HW0107
|WASHER-LOCK-3/8"
|
|
|12
|-
|6
|HW0005
|NUT-HEX-3/8-16
|
|
|12
|-
|7
|PL0307
|INSULATOR-MALE STUD
|
|
|4
|-
|8
|HW0106
|WASHER-FLAT-5/16"-SAE
|
|
|8
|-
|9
|HW0105
|WASHER-LOCK-5/16"
|
|
|8
|-
|10
|HW0004
|NUT-HEX-5/16-18
|
|
|8
|-
|11
|E0622
|RESTRAINT-1/2"
|
|''Grip size .450" to .560"''
|1
|-
|12
|E0608-1
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .450" to .560"''
|2
|-
|13
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|3
|-
|14
|E1016
|FUSE HOLDER
|
|
|1
|-
|15
|E0325
|FUSE-7 AMP-250VAC
|
|''FLM-7 or FNM-7''
|1
|-
|16
|HW0130
|SCREW-RHMS-#8-32 X 1/2"
|
|
|1
|-
|17
|HW0133
|WASHER-FLAT-#8-SAE
|
|
|1
|-
|18
|HW0132
|NUT-NILN-#8-32
|
|
|1
|}

=== '''<big>Magnet Panel (Helical Actuator)</big>''' ===
[[File:BE-TS Magnet Panel (Helical Actuator).png|alt=BE-TS Magnet Panel (Helical Actuator)|frameless|557x557px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41637001
|PANEL-COMPONENT MOUNTING
|
|
|1
|-
|2
|41637002
|WIRE WAY-SHORT
|
|
|2
|-
|3
|41637003
|WIRE WAY-LONG
|
|
|1
|-
|4
|41637004
|TRACK-MOUNTING-SHORT
|
|
|1
|-
|5
|41637005
|TRACK-MOUNTING-LONG
|
|
|1
|-
|6
|HW0130
|SCREW-RHMS-#8-32 X 1/2"
|
| rowspan="3" |''Mounting track hardware (Not shown)''
|10
|-
|7
|HW0132
|WASHER-FLAT-#8-SAE
|
|10
|-
|8
|HW0133
|NUT-NILN-#8-32
|
|16
|-
|9
|E1020
|TERMINAL BLOCK
|
|
|12
|-
|10
|E1040
|END BARRIER
|
|
|2
|-
|11
|E1330
|END ANCHOR
|
|
|4
|-
|12
|E1009
|RECTIFIER-FULL WAVE BRIDGE
|
|
|2
|-
|13
|HW0135
|SCREW-RHMS-#8-32 X 3/4"
|
|
|2
|-
|14
|E1313
|SOCKET-RELAY-8 PIN
|
|
|2
|-
|15
|E0331
|RELAY-DPDT-110VAC
|
|''With Indicator Light''
|2
|-
|16
|HW0139
|SCREW-RHMS-#8-32 X 1 1/4"
|
|
|4
|}

=== '''<big>Extended Reach Hydraulics (Helical Actuator)</big>''' ===

==== <big>''[Discontinued] Helical Actuator''</big> ====
[[File:BE-TS (Discontinued) Helical Actuator.png|alt=BE-TS (Discontinued) Helical Actuator|frameless|546x546px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43042009
|3/8" TUBE X #6 JIC HARD-PIPE
|
|
|2
|-
|2
|H1579
|ADAPTER-90 DEG-#6 JICM X #4 MNPT
|
|
|2
|-
|3
|H0010
|FITTING-BULKHEAD-3/4-16 X #4 FNPT
|
|
|2
|-
|4
|43055017
|ELBOW-BULKHEAD
|
|
|2
|-
|5
|HW0302
|BOLT-HHCS-1/4-20 X 3/4"
|
|
|4
|-
|6
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
| rowspan="3" |7
|4-48-0402-0402
|HYD HOSE-1/4" X 48" (BE-24 UNITS)
|
| rowspan="3" |''Cylinder rod-end hose''
| rowspan="3" |1
|-
|4-54-0402-0402
|HYD HOSE-1/4" X 54" (BE-36 UNITS)
|
|-
|4-56-0402-0402
|HYD HOSE-1/4" X 56" (BE-42 UNITS)
|
|-
| rowspan="3" |8
|4-38-0402-0402
|HYD HOSE-1/4" X 38" (BE-24 UNITS)
|
| rowspan="3" |''Cylinder rod-end hose''
| rowspan="3" |1
|-
|4-44-0402-0402
|HYD HOSE-1/4" X 44" (BE-36 UNITS)
|
|-
|4-46-0402-0402
|HYD HOSE-1/4" X 46" (BE-42 UNITS)
|
|-
|9
|41257035
|STANDOFF-HOSE
|
|
|2
|-
|10
|HW1093
|CLAMP-CABLE-3/4"
|
|
|2
|-
|11
|HW0311
|BOLT-FHSCS-1/4-20 X 3/4"
|
|
|2
|-
|12
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|}

==== <big>''[Current] Helical Actuator''</big> ====
[[File:BE-TS (Current) Helical Actuator.png|alt=BE-TS (Current) Helical Actuator|frameless|567x567px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43042013
|3/8" TUBE X #6 JIC HARD-PIPE
|
|
|2
|-
|2
|H1579
|ADAPTER-90 DEG-#6 JICM X #4 MNPT
|
|
|2
|-
|3
|H0010
|FITTING-BULKHEAD-3/4-16 X #4 FNPT
|
|
|2
|-
|4
|43055021
|ELBOW-BULKHEAD
|
|
|2
|-
|5
|HW0302
|BOLT-HHCS-1/4-20 X 3/4"
|
|
|4
|-
|6
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
| rowspan="3" |7
|4-48-0402-0402
|HYD HOSE-1/4" X 48" (BE-24 UNITS)
|
| rowspan="3" |''Cylinder rod-end hose''
| rowspan="3" |1
|-
|4-54-0402-0402
|HYD HOSE-1/4" X 54" (BE-36 UNITS)
|
|-
|4-56-0402-0402
|HYD HOSE-1/4" X 56" (BE-42 UNITS)
|
|-
| rowspan="3" |8
|4-38-0402-0402
|HYD HOSE-1/4" X 38" (BE-24 UNITS)
|
| rowspan="3" |''Cylinder rod-end hose''
| rowspan="3" |1
|-
|4-44-0402-0402
|HYD HOSE-1/4" X 44" (BE-36 UNITS)
|
|-
|4-46-0402-0402
|HYD HOSE-1/4" X 46" (BE-42 UNITS)
|
|-
|9
|41257035
|STANDOFF-HOSE
|
|
|2
|-
|10
|HW1093
|CLAMP-CABLE-3/4"
|
|
|2
|-
|11
|HW0311
|BOLT-FHSCS-1/4-20 X 3/4"
|
|
|2
|-
|12
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|}

=== '''<big>Vacuum Extended Reach (Helical Actuator)</big>''' ===

==== <big>'''''Non-Pivoting Cup Extended Reach Vacuum Arm (Helical Actuator)'''''</big> ====
[[File:BE-TS Non-Pivoting Cup Extended Reach Vacuum Arm (Helical Actuator).png|alt=BE-TS Non-Pivoting Cup Extended Reach Vacuum Arm (Helical Actuator)|frameless|545x545px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41255005
|ARM-EXTENSION
|
|
|1
|-
|2
|41255004
|HOUSING-EXTENDED REACH
|
|
|1
|-
|3
|HC0416
|CYLINDER-2 1/2" X 12"
|
|
|1
|-
|4
|43057042
|PIN-CYLINDER-REAR
|
|
|1
|-
|5
|43057043
|PIN-CYLINDER-ROD
|
|
|1
|-
|6
|HW1132
|RETAINING RING-3/4" I.D.
|
|
|4
|-
|7
|H1578
|ADAPTER-90 DEG-#6 JIC X # 6 NPT
|
|
|2
|-
|8
|50057008
|PLATE-END
|
|
|1
|-
|9
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|10
|HW0104
|WASHER-FLAT-1/4"
|
|
|8
|-
|11
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|13
|HW0812
|SCREW-SHSS-1/4-20 X 5/8"-HALF DOG
|
|
|28
|-
|14
|HW0002
|NUT-HEX-1/4-20
|
|
|28
|-
|15
|41258002
|PLATE-BEARING
|80258001
|''Side''
|2
|-
|16
|41258005
|PLATE-SHIM
|80258001
|''Side''
|2
|-
|17
|41258003
|PLATE-BEARING
|80258001
|''Upper / lower''
|2
|-
|18
|41258004
|PLATE-SHIM
|80258001
|''Upper / lower''
|2
|}
<big>'''''Pivoting Cup Extended Reach Vacuum Arm (Helical Actuator)'''''</big>

[[File:BE-TS Pivoting Cup Extended Reach Vacuum Arm (Helical Actuator).png|alt=BE-TS Pivoting Cup Extended Reach Vacuum Arm (Helical Actuator)|frameless|553x553px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43055011
|ARM-EXTENSION
|
|''Pivoting cup only''
|1
|-
|2
|43055012
|HOUSING-EXTENDED REACH
|
|''Pivoting cup only''
|1
|-
|3
|HC0415
|CYLINDER-2 1/2" X 8"
|
|
|1
|-
|4
|43057042
|PIN-CYLINDER-REAR
|
|
|1
|-
|5
|43057043
|PIN-CYLINDER-ROD
|
|
|1
|-
|6
|HW1132
|RETAINING RING-3/4" I.D.
|
|
|4
|-
|7
|H1578
|ADAPTER-90 DEG-#6 JIC X # 6 NPT
|
|
|2
|-
|8
|50057008
|PLATE-END
|
|
|1
|-
|9
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|10
|HW0104
|WASHER-FLAT-1/4"
|
|
|8
|-
|11
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|13
|HW0812
|SCREW-SHSS-1/4-20 X 5/8"-HALF DOG
|
|
|24
|-
|14
|HW0002
|NUT-HEX-1/4-20
|
|
|24
|-
|15
|43058013
|PLATE-BEARING
|
|''Side''
|2
|-
|16
|43058016
|PLATE-SHIM
|
|''Side''
|2
|-
|17
|43058014
|PLATE-BEARING
|
|''Upper / lower''
|2
|-
|18
|43058015
|PLATE-SHIM
|
|''Upper / lower''
|2
|-
|19
|HW1043
|CLAMP-CYLINDER
|
|
|2
|-
|20
|43058019
|SUPPORT-CABLE-BAND CLAMP
|
|
|2
|-
|21
|E0622
|RESTRAINT-1/2"
|
|''Grip size .450" to .560"''
|2
|-
|22
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|2
|-
|23
|HW0104
|WASHER-FLAT-1/4"
|
|
|4
|-
|24
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|}

=== '''<big>Magnet Extended Reach (Helical Actuator)</big>''' ===

==== <big>'''''[Discontinued] Extended Reach Magnet Arm (Helical Actuator)'''''</big> ====
[[File:BE-TS (Discontinued) Extended Reach Magnet Arm (Helical Actuator).png|alt=BE-TS (Discontinued) Extended Reach Magnet Arm (Helical Actuator)|frameless|543x543px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43055011
|ARM-EXTENSION
|
|
|1
|-
|2
|43055012
|HOUSING-EXTENDED REACH
|
|
|1
|-
|3
|HC0415
|CYLINDER-2 1/2" X 8"
|
|
|1
|-
|4
|43057042
|PIN-CYLINDER-REAR
|
|
|1
|-
|5
|43057043
|PIN-CYLINDER-ROD
|
|
|1
|-
|6
|HW1132
|RETAINING RING-3/4" I.D.
|
|
|4
|-
|7
|H1578
|ADAPTER-90 DEG-#6 JIC X # 6 NPT
|
|
|2
|-
|8
|50057008
|PLATE-END
|
|
|1
|-
|9
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|10
|HW0104
|WASHER-FLAT-1/4"
|
|
|8
|-
|11
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|13
|HW0812
|SCREW-SHSS-1/4-20 X 5/8"-HALF DOG
|
|
|24
|-
|14
|HW0002
|NUT-HEX-1/4-20
|
|
|24
|-
|15
|43058013
|PLATE-BEARING
|
|''Side''
|2
|-
|16
|43058016
|PLATE-SHIM
|
|''Side''
|2
|-
|17
|43058014
|PLATE-BEARING
|
|''Upper / lower''
|2
|-
|18
|43058015
|PLATE-SHIM
|
|''Upper / lower''
|2
|-
|19
|HW1043
|CLAMP-CYLINDER
|
|
|2
|-
|20
|43058019
|SUPPORT-CABLE-BAND CLAMP
|
|
|2
|-
|21
|PL0501
|GROMMET-1/2" I.D.
|
|
|4
|-
|22
|HW0104
|WASHER-FLAT-1/4"
|
|
|4
|-
|23
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|24
|43057004-2
|SUPPORT-CABLE-MAGNET
|
|
|2
|}
<big>'''''[Current] Extended Reach Magnet Arm (Helical Actuator)'''''</big>

[[File:BE-TS (Current) Extended Reach Magnet Arm (Helical Actuator).png|alt=BE-TS (Current) Extended Reach Magnet Arm (Helical Actuator)|frameless|539x539px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|50055004
|ARM-EXTENSION
|
|
|1
|-
|2
|50055005
|HOUSING-EXTENDED REACH
|
|
|1
|-
|3
|HC0415
|CYLINDER-2 1/2" X 8"
|
|
|1
|-
|4
|43057042
|PIN-CYLINDER-REAR
|
|
|1
|-
|5
|43057043
|PIN-CYLINDER-ROD
|
|
|1
|-
|6
|HW1132
|RETAINING RING-3/4" I.D.
|
|
|4
|-
|7
|H1578
|ADAPTER-90 DEG-#6 JIC X # 6 NPT
|
|
|2
|-
|8
|50057008
|PLATE-END
|
|
|1
|-
|9
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|10
|HW0104
|WASHER-FLAT-1/4"
|
|
|8
|-
|11
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|13
|HW0812
|SCREW-SHSS-1/4-20 X 5/8"-HALF DOG
|
|
|20
|-
|14
|HW0002
|NUT-HEX-1/4-20
|
|
|20
|-
|15
|50058009
|PLATE-BEARING
|
|''Side''
|2
|-
|16
|50058012
|PLATE-SHIM
|
|''Side''
|2
|-
|17
|50058010
|PLATE-BEARING
|
|''Upper / lower''
|2
|-
|18
|50058011
|PLATE-SHIM
|
|''Upper / lower''
|2
|-
|19
|HW1043
|CLAMP-CYLINDER
|
|
|2
|-
|20
|43058019
|SUPPORT-CABLE-BAND CLAMP
|
|
|2
|-
|21
|PL0501
|GROMMET-1/2" I.D.
|
|
|4
|-
|22
|HW0104
|WASHER-FLAT-1/4"
|
|
|4
|-
|23
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|24
|43057004-2
|SUPPORT-CABLE-MAGNET
|
|
|2
|}

== <big>Drive and Idler Wheels</big> ==

=== <big>Drive Wheel Mounting</big> ===
[[File:BE-TS Drive Wheel Mounting.png|alt=BE-TS Drive Wheel Mounting|frameless|519x519px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HW0503
|BOLT-HHCS-1/2-13 X 1 1/2"
|
|
|6
|-
|2
|HW0504
|BOLT-HHCS-1/2-13 X 2"
|
|''Cylinder Bracket bolt only''
|2
|-
|3
|HW0110
|WASHER-LOCK-1/2"
|
|
|8
|-
|4
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|8
|}

=== <big>Drive Wheel Motors</big> ===
[[File:BE-TS Drive Wheel Motors.png|alt=BE-TS Drive Wheel Motors|frameless|535x535px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="2" |1
|43822001-6B
|FLOOR DRIVE ASSEMBLY (W/ 200CC MOTOR)
|
|''† See notes''
|2
|-
|43822004-6B
|FLOOR DRIVE ASSEMBLY (W/ 400CC MOTOR)
|
|''† See notes''
|2
|-
|2
|43827004
|PLATE-MOTOR MOUNTING
|
|
|2
|-
|3
|HW0416
|BOLT-SHCS-3/8-16 X 1"
|
|
|8
|-
|4
|HW0107
|WASHER-LOCK-3/8"
|
|
|8
|-
|5
|H1612
|ADAPTER-90 DEG-#8 JICM X #10 SAEM
|
|
|4
|-
|6
|N/A
|ROD-THREADED-1/2-13 X 7 3/4"
|
|''†† See notes''
|8
|-
|7
|N/A
|SPACER-DRIVE WHEEL-4.75" LG
|
|''†† See notes''
|8
|-
|8
|HW0110
|WASHER-LOCK-1/2"
|
|
|8
|-
|9
|HW0007
|NUT-HEX-1/2-13
|
|
|8
|-
|10
|43827006
|SPACER-DRIVE WHEEL-4.125" LG
|
|Must be ordered as a set of 4
|8
|-
|11
|HW0516
|BOLT-HHCS-1/2-13 X 6 1/2"
|
|
|8
|-
|12
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|8
|-
| rowspan="2" |13
|N/A
|MOTOR-HYDRAULIC-200CC
|
|''††† Keyed Shaft''
|<nowiki>-</nowiki>
|-
|N/A
|MOTOR-HYDRAULIC-400CC
|
|''††† Keyed Shaft''
|<nowiki>-</nowiki>
|-
|14
|HW1071
|KEY-WOODRUFF-#808 STD
|
|
|2
|-
| rowspan="2" |15
|HC0124-6B
|MOTOR-HYDRAULIC-200CC
|
|''† Spline Shaft''
|2
|-
|HC0126-6B
|MOTOR-HYDRAULIC-400CC
|80322003
|''† Spline Shaft''
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† 200CC Motors required for units equipped with Parallel Drive Circuit.''
''400CC Motors required for units equipped with Series Drive Circuit.''

''See [https://tech.bhs1.com/index.php/(BE-TS)_Triple_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-401)#Cross_Port_Relief Cross Port Relief] section to determine if unit is Parallel or Series equipped and approximate effectivity of each type.''
|-
| colspan="6" |''†† Parts obsolete and no longer available. Must replace with Items 10 & 11.''
|-
| colspan="6" |''††† Parts obsolete and no longer available. Must replace with Spline Drive Conversion Kit.''
|-
| colspan="6" |'''''NOTE:''' Effectivity dates refer to dates new extractor units are shipped from the factory. Replacement part effectivity may differ due to factory inventory levels at time of parts order. Consult factory if unsure of parts needed.''
|}

=== <big>Drive Wheel Bearings</big> ===
[[File:BE-TS Drive Wheel Bearings.png|alt=BE-TS Drive Wheel Bearings|frameless|537x537px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43825001
|FRAME-FLOOR DRIVE
|
|
|2
|-
|2
|C0510-1
|WHEEL-10" X 5"-POLY
|80322001
|
|2
|-
|3
|43822003
|SHAFT-WHEEL (W/ COUPLING BODY)
|
|''Available in multiple kits''
|2
|-
|4
|43897004
|KEY-3/8" X 4 3/4"
|80322001
|
|2
|-
|5
|PT0430
|FLANGE BEARING-4 BOLT-1 1/2"
|80322001
|
|4
|-
|6
|HW0504
|BOLT-HHCS-1/2-13 X 2"
|
|
|8
|-
|7
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|16
|-
|8
|HW0110
|WASHER-LOCK-1/2"
|
|
|16
|-
|9
|HW0007
|NUT-HEX-1/2-13
|
|
|16
|-
|10
|PT0321
|CHAIN-COUPLING-#50
|
|''Includes connecting pin''
|2
|-
|11
|N/A
|COUPLING BODY-TAPER BORE-#50
|
|''† See notes''
|2
|-
|12
|N/A
|BUSHING-TAPER LOCK-1"
|
|''† See notes''
|2
|-
|13
|HW0323
|BOLT-HHCS-5/16-18 X 1"
|
|
|8
|-
|14
|PT0330
|COUPLING BODY-#50-SPLINE BORE
|80322003
|
|2
|-
|15
|HW1110
|RETAINING RING-1 1/2"-HEAVY DUTY
|
|''†† Available in multiple kits''
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Parts obsolete and no longer available. Spline Drive Conversion Kit required. Reuse of bushing after disassembly not recommended.''
|-
| colspan="6" |''† † Retaining Rings used on units shipped after 7/01/12. Units shipped from 7/01/13 are equipped with (2) Retaining Rings per shaft - (1) on each side of the wheel. Units shipped after 11/01/13 are equipped with only (1) Snap Rings as shown. Second Snap Ring is no longer used or required.''
|-
| colspan="6" |''NOTE: Effectivity dates refer to dates new extractor units are shipped from the factory. Replacement part effectivity '''may''' differ due to factory inventory levels at time of parts order. Consult factory if unsure of parts needed.''
|}

=== <big>Drive Wheel Assembly</big> ===
[[File:BE-TS Drive Wheel Assembly.png|alt=BE-TS Drive Wheel Assembly|frameless|543x543px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43822005
|RADIAL PISTON DRIVE WHEEL ASSEMBLY
|
|''Includes Items 1 through 6''
|2
|-
|1
|43825003
|RADIAL PISTON DRIVE WHEEL MOUNT
|
|
|1
|-
|2
|HC0160-1
|400CC RADIAL PISTON MOTOR
|
|''Includes nuts & studs''
|1
|-
|REF
|HC0160-STUD
|STUD-M14-1.5 X 46MM
|
|''Replacement motor stud''
|A/R
|-
|REF
|HC0160-NUT
|NUT-FLANGED HEX-M14-1.5
|
|''Replacement motor nut''
|A/R
|-
|3
|C0511
|WHEEL-POLY-10 X 5"-FLANGE MOUNT
|
|
|1
|-
|4
|HW0514
|BOLT-HHCS-1/2-13 X 2 1/2"
|
|
|6
|-
|5
|HW0110
|WASHER-LOCK-1/2"
|
|
|6
|-
|6
|HW0007
|NUT-HEX-1/2-13
|
|
|6
|-
|7
|H1612
|ADAPTER-H-90 DEG-#10 SAEM X #8 JICM
|
|
|2
|-
|8
|H1539
|ADAPTER-#8 JIC X #6 SAE
|
|
|1
|-
|9
|H1586
|ADAPTER-90 DEG-#8 JICSW X #6 NPT
|
|
|1
|-
|10
|H0801
|TEE-H-#6 NPT
|
|
|1
|-
|11
|H1501
|ADAPTER-#8 JIC X #6 NPT
|
|
|1
|-
|12
|H0200
|REDUCER-#6 NPT X #4 NPT
|
|
|1
|-
|13
|H0206
|PLUG-#4 NPT
|
|''† Left Drive Wheel only''
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Plug used on Left Drive Wheel Assembly only. Hose from Left Drive Wheel Assembly is connected to tee on Right Drive Wheel Assembly.''
|}

=== <big>Idler Casters</big> ===
[[File:BE-TS Idler Casters.png|alt=BE-TS Idler Casters|frameless|545x545px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|C0500-1
|CASTER-RIGID-10" X 5"-POLY
|
|
|2
|-
|2
|HW0504
|BOLT-HHCS-1/2-13 X 2"
|
|
|6
|-
|3
|HW0514
|BOLT-HHCS-1/2-13 X 2 1/2"
|
|''For Cylinder Bracket position''
|2
|-
|4
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|16
|-
|5
|HW0110
|WASHER-LOCK-1/2"
|
|
|8
|-
|6
|HW0007
|NUT-HEX-1/2-13
|
|
|8
|}

== <big>Electrical</big> ==

=== <big>AC Power Stanchion</big> ===

==== <big>''Aero-Motive Energy Rail''</big> ====
[[File:BE-TS Aero-Motive Energy Rail.png|alt=BE-TS Aero-Motive Energy Rail|frameless|536x536px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43835001
|STANCHION-POWER
|
|
|1
|-
|2
|HW0511
|BOLT-HHCS-1/2-13 X 3 3/4"
|
|
|2
|-
|3
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|2
|-
|4
|HW0110
|WASHER-LOCK-1/2"
|
|
|2
|-
|5
|HW0007
|NUT-HEX-1/2-13
|
|
|2
|-
|6
|46837014-2
|TOW ARM-COLLECTOR TROLLEY
|
|
|1
|-
|7
|46838015
|SPACER BLOCK-TOW ARM
|
|
|1
|-
|8
|HW1030
|U-BOLT-3/8-16 X 2" X 5"-SQUARE BEND
|
|
|1
|-
|9
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|2
|-
|10
|HW0107
|WASHER-LOCK-3/8"
|
|
|2
|-
|11
|HW0005
|NUT-HEX-3/8-16
|
|
|2
|-
|12
|E0632
|RESTRAINT-3/4"
|
|''Grip size .625" to .750"''
|1
|-
|13
|E0618
|LOCKNUT-CONDUIT-3/4"
|
|
|1
|-
|14
|HW1051
|EYE BOLT-3/8-16 X 5 1/2"
|
|
|2
|-
|15
|HW0126
|WASHER-FLAT-3/8"-FENDER
|
|
|4
|-
|16
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|17
|HW0005
|NUT-HEX-3/8-16
|
|
|4
|-
|18
|BD0010
|TROLLEY-ENERGY RAIL
|
| rowspan="2" |''Aero-Motive Rail only''

''(orange housing color)''
|1
|-
|19
|BD0100
|BRUSH-TROLLEY
|
|4
|}

==== '''<big>''Vahle Energy Rail''</big>''' ====
[[File:BE-TS Vahle Energy Rail.png|alt=BE-TS Vahle Energy Rail|frameless|535x535px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1A
|BD0031
|TROLLEY-ENERGY RAIL, KSL
|
| rowspan="3" |''† Vahle KSL Rail only''

''(green housing color)''
|1
|-
|2A
|BD0040
|BRUSH-PHASE, KSL
|
|3
|-
|3A
|BD0041
|BRUSH-GROUND, KSL
|
|1
|-
|1B
|BD0231
|TROLLEY-ENERGY RAIL, KBH
|
| rowspan="3" |''† Vahle KBH Rail only''

''(gray housing color)''

''(Nots shown)''
|1
|-
|2B
|BD0240
|BRUSH-PHASE, KBH
|
|3
|-
|3B
|BD0241
|BRUSH-GROUND, KBH
|
|1
|-
| rowspan="2" |4
|BD0030
|TOW ARM-COLLECTOR TROLLEY, KSL
|
|''† Vahle KSL Rail only''

''(green housing color)''
|1
|-
|BD0230
|TOW ARM-COLLECTOR TROLLEY, KBH
|
|''† Vahle KBH Rail only''

''(gray housing color)''
|1
|-
|5
|46838015
|SPACER-BLOCK-TOW ARM
|
|''†† See notes''
|1
|-
|6
|41237083-2
|BRACKET-TOW ARM
|
|''†† See notes''
|1
|-
|7
|HW1054
|U-BOLT-5/16-18 X 2" X 5"-SQUARE BEND
|
|
|1
|-
|8
|HW0323
|BOLT-HHCS-5/16-18 X 1"
|
|
|2
|-
|9
|HW0106
|WASHER-FLAT-5/16"-SAE
|
|
|2
|-
|10
|HW0150
|WASHER-FLAT-5/16"-FENDER
|
|
|2
|-
|11
|HW0105
|WASHER-LOCK-5/16"
|
|
|2
|-
|12
|HW0004
|NUT-HEX-5/16-18
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Verify Energy Rail type (KSL OR KBH) by the color of the energy rail housing.''
|-
| colspan="6" |''†† Not all units equipped with Tow Arm Bracket. Location of Spacer Block and/or Tow Arm Bracket may vary from configuration shown.''
|}

=== '''<big>Control Panel</big>''' ===
'''<big>''[Discontinued] Control Panel for Units with 10 HP Power Unit''</big>'''

[[File:BE-TS (Discontinued) Control Panel for Units with 10HP.png|alt=BE-TS (Discontinued) Control Panel for Units with 10HP|frameless|539x539px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|N/A
|ENCLOSURE-CONTROL PANEL-16" X 14" X 6"
|
|CONSULT FACTORY
|1
|-
|2
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|3
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|4
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|5
|E0616
|RESTRAINT-1/2"
|
|Grip size .250" to.375"
|1
|-
|6
|E0632
|RESTRAINT-3/4"
|
|Grip size .625" to .750"
|2
|-
|7
|E0613
|RESTRAINT-3/4"
|
|Grip size .500" to .625"
|2
|-
|8
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|''Not shown''
|1
|-
|9
|E0618
|LOCKNUT-CONDUIT-3/4"
|
|''Not shown''
|4
|}
[[File:BE-TS (Discontinued) Control Panel for Units with 10HP Detail.png|alt=BE-TS (Discontinued) Control Panel for Units with 10HP Detail|frameless|556x556px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0640
|PANEL-COMPONENT MOUNTING
|
|BLANK PANEL WITHOUT HOLES
|1
|-
|2
|E0120
|MAGNETIC STARTER-NEMA 1 3/4"
|
|WITH OVERLOAD
|1
|-
|3
|HW0130
|SCREW-RHMS-#8-32 X 1/2"
|
|
|17
|-
|4
|HW0133
|WASHER-FLAT-#8-SAE
|
|
|17
|-
|5
|HW0132
|NUT-NILN-#8-32
|
|
|17
|-
|6
|E0207-1
|TRANSFORMER
|
|480VAC TO 120VAC, 0.75 Kva
|1
|-
|7
|HW0302
|BOLT-HHCS-1/4-20 X 3/4"
|
|
|4
|-
|8
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|9
|HW0003
|NUT-NILN-1/4-20
|
|
|4
|-
|10
|E1023
|WIREWAY
|
|SOLD BY LENGTH
|A/R
|-
|11
|E1024
|MOUNTING TRACK
|
|SOLD BY LENGTH
|A/R
|-
|12
|E1020
|TERMINAL BLOCK
|
|
|16
|-
|13
|E1040
|END BARRIER
|
|
|2
|-
|14
|E1330
|END ANCHOR
|
|
|4
|-
|15
|E0341
|GROUND LUG
|
|
|1
|-
|16
|E0902
|FUSE-6A
|
|FLM-6
|1
|}

==== '''<big>''[Current] Control Panel for Units with 20 HP Power Unit''</big>''' ====
[[File:BE-TS (Current) Control Panel for Units with 20HP.png|alt=BE-TS (Current) Control Panel for Units with 20HP|frameless|601x601px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|N/A
|ENCLOSURE-24" X 16" X 6"
|
|CONSULT FACTORY
|1
|-
|2
|E0123-1
|HANDLE-DISCONNECT
|
|INCL. MOUNTING SCREWS
|1
|-
|3
|E0662
|RESTRAINT-3/4"-LIQUID TIGHT
|
|INCL. LOCKNUT
|1
|-
|4
|E0613
|RESTRAINT-3/4"
|
|GRIP SIZE .500" TO .625"
|2
|-
|5
|E0632
|RESTRAINT-3/4"
|
|GRIP SIZE .625" TO .750"
|1
|-
|6
|E0618
|LOCKNUT-CONDUIT-3/4"
|
|
|3
|-
|7
|E0661
|RESTRAINT-3/4"-90 DEG-LIQUID TIGHT
|
|INCL. LOCKNUT
|1
|-
|8
|E0616
|RESTRAINT-1/2"
|
|GRIP SIZE .250" TO .375"
|1
|-
|9
|E0622
|RESTRAINT-1/2"
|
|GRIP SIZE .450" TO .560"
|2
|-
|10
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|3
|-
|11
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|12
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|13
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|14
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|}
[[File:BE-TS (Current) Control Panel for Units with 20HP Details.png|alt=BE-TS (Current) Control Panel for Units with 20HP Details|frameless|645x645px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|YE0506
|PANEL-COMPONENT MOUNTING
|
|''Blank panel without holes''
|1
|-
|2
|YE0205-1
|SWITCH-DISCONNECT-80A
|
|
|1
|-
|3
|43036007
|SHAFT-DISCONNECT
|
|
|1
|-
|4
|YE0409
|FUSE HOLDER-SINGLE POLE
|
|
|3
|-
|5
|E0914
|FUSE-10A
|
|''FLM-10''
|1
|-
|6
|E0902
|FUSE-6A
|
|''FLM-6''
|1
|-
|7
|E0903
|FUSE-12A
|
|''FLM-12''
|1
|-
|8
|YE0402
|TERMINAL BLOCK
|
|
|17
|-
|9
|YE0405
|END BARRIER
|
|
|2
|-
|10
|YE0406
|END ANCHOR
|
|
|6
|-
|11
|E0136
|FUSE HOLDER-3 POLE
|
|
|1
|-
|12
|YE0901
|FUSE-40A
|
|JTD-40-ID
|3
|-
|13
|E1013
|BASE-RELAY
|
|
|1
|-
|14
|E1012
|RELAY-11 PIN
|
|
|1
|-
|15
|E0137
|FUSE HOLDER-2 POLE
|
|
|1
|-
|16
|YE0902
|FUSE-10A
|
|''KLDR-10''
|2
|-
| rowspan="2" |17
|N/A
|CONTACTOR, "A40" SERIES
|
|''† See notes''
|1
|-
|E0132-1
|CONTACTOR, "AF38" SERIES
|80332009
|
|1
|-
| rowspan="2" |18
|N/A
|OVERLOAD, "TA" SERIES
|
|''† See notes''
|1
|-
|E0131-1
|OVERLOAD, "TF" SERIES
|80332009
|
|1
|-
|19
|E1023
|WIREWAY
|
|''Sold by length''
|A/R
|-
|20
|E0908
|MOUNTING RAIL
|
|''Sold by length''
|A/R
|-
|21
|E1070
|GROUND BAR-4 POSITION
|
|
|1
|-
|22
|E1071
|GROUND BAR-7 POSITION
|
|
|1
|-
|23
|HW1061
|SCREW-RHMS-#8-32 X 1"
|
|
|3
|-
|24
|HW0130
|SCREW-RHMS-#8-32 X 1/2"
|
| rowspan="3" |''Track and Wireway mounting hardware (Not shown)''
|14
|-
|25
|HW0133
|WASHER-FLAT-#8
|
|14
|-
|26
|HW0132
|NUT-NILN-#8-32
|
|17
|-
|27
|E0139
|AUXILIARY CONTACT BLOCK
|80332009
|''†† See notes''
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† "A40" Series Contactor and "TA" Series Overload no longer available as of mid-March 2022. Components must be replaced with current Overload & Relay Kit 80332009.''
|-
| colspan="6" |''†† Auxiliary contact Block required for units equipped with "AF38" Series Contactor & "TF" Series Overload.''
|}

=== '''<big>Transformer</big>''' ===
'''<big>''Transformer for Units with 20 HP Power Unit''</big>'''

[[File:BE-TS Transformer for Units with 20HP.png|alt=BE-TS Transformer for Units with 20HP|frameless|554x554px]]

{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0220
|TRANSFORMER
|
|''480VAC to 120VAC, 3kVA''
|1
|-
|2
|E0608-1
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .450" to .560"''
|2
|-
|3
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|2
|-
|4
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|3
|-
|5
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|6
|-
|6
|HW0103
|WASHER-LOCK-1/4"
|
|
|3
|-
|7
|HW0002
|NUT-HEX-1/4-20
|
|
|3
|}

=== <big>Operator Console</big> ===
[[File:BE-TS Operator Console Electrical.png|alt=BE-TS Operator Console Electrical|frameless|543x543px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0327
|KEYED ACTUATOR ASSEMBLY
|
|''Includes 2 Keys & Contact Block''
|1
|-
|2
|E0351
|KEY-REPLACEMENT
|
|''Set of 2 Keys''
|A/R
|-
|3
|E0309-1
|HOUR METER
|
|''† Includes mounting hardware''
|1
|-
|4
|N/A
|SWITCH-SELECTOR-3 POSITION
|
|''ON-OFF-ON, †† See notes''
|1
|-
| rowspan="2" |5
|N/A
|LEGEND PLATE-VACUUM
|
|''††† See notes''
|1
|-
|N/A
|LEGEND PLATE-MAGNET
|
|''††† See notes''
|1
|-
|6
|N/A
|CONTACT BLOCK-N/O
|
|''†† See notes''
|2
|-
|7
|N/A
|CONTACT BLOCK-N/C
|
|''†† See notes''
|2
|-
|8
|E1083
|SWITCH-SELECTOR-3 POSITION
|80232001
|''OFF-ON-OFF''
|1
|-
|9
|E1080
|CONTACT BLOCK-N/O & N/C
|80232001
|
|2
|-
|10
|YE0311
|SWITCH-EMERGENCY STOP
|
|
|1
|-
|11
|YE0407
|LEGEND PLATE-EMERGENCY STOP
|
|
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Current Hour Meter is 3-Bolt version. Replacement of 4-Bolt version will require new mounting holes to be drilled in dashboard.''
|-
| colspan="6" |''†† Parts no longer available. Must order new Selector Switch Kit 80232001''
|-
| colspan="6" |''††† Parts no longer available. See [https://tech.bhs1.com/index.php/(BE-TS)_Triple_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-401)#Labels_&_Placards Labels & Placards] section for current Placards''
|}

=== <big>Foot Switch</big> ===
[[File:BE-TS Foot Switch Electrical.png|alt=BE-TS Foot Switch Electrical|frameless|701x701px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0301-1
|SWITCH-FOOT OPERATED
|
|''† See notes''
|1
|-
|2
|E0613
|RESTRAINT-3/4"
|
|''Grip size .500" to .625"''
|1
|-
|3
|E0515
|CORD-14-3-SO/SOW
|
|
|9'
|-
|4
|HC0303
|BOLT-HHCS-1/4-20 X 1"
|
|''If equipped''
|2
|-
|5
|HC0103
|WASHER-1/4"-LOCK
|
|''If equipped''
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Open-Style Switch is a direct replacement for discontinued, Covered-Style Switch.''
|}

=== <big>'''Gate Switch'''</big> ===
[[File:BE-TS Gate Switch Electrical.png|alt=BE-TS Gate Switch Electrical|frameless|613x613px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0312
|SWITCH-PUSH BUTTON
|
|
|1
|-
|2
|43017041
|MOUNT-GATE SWITCH
|
|
|1
|-
|3
|HW1077
|SCREW-RHMS-#10-24 X 5/8"
|
|
|2
|-
|4
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|2
|-
|5
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|6
|HW0307
|BOLT-SHCS-1/4-20 X 1"
|
|
|2
|-
|7
|PL0502
|GROMMET-3/8" I.D.
|
|
|1
|-
|8
|YE0305
|SWITCH-ROLLER
|
|
|1
|-
|9
|SS0303
|WASHER-FLAT-#8
|
|
|2
|-
|10
|SS0111
|SCREW-SHCS-#8-32 X 1 1/2"
|
|
|2
|-
|11
|SS0203
|NUT-NILN-#8-32
|
|
|2
|-
|12
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|1
|}

=== <big>'''Proximity Switch'''</big> ===
[[File:BE-TS Proximity Switch Electrical.png|alt=BE-TS Proximity Switch Electrical|frameless|545x545px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0314
|SENSOR-PROXIMITY-30MM
|
|
|1
|-
|2
|43017027-2
|BRACKET-PROXIMITY SENSOR
|
|
|1
|-
|3
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|2
|-
|4
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|5
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|-
| rowspan="2" |6
|43017037-2
|ANGLE-PROXIMITY SENSOR TARGET
|
|''Rotary Actuator units''
|1
|-
|43017084-2
|ANGLE-PROXIMITY SENSOR TARGET
|
|''Helical Actuator units''
|1
|-
|7
|HW0341
|BOLT-FHSCS-1/4-20 X 5/8"
|
|
|2
|}

=== <big>'''120V Receptacle'''</big> ===
[[File:BE-TS 120V-Receptacle.png|alt=BE-TS 120V Receptacle|frameless|544x544px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0611
|JUNCTION BOX-4" X 2" X 2"
|
|
|1
|-
|2
|E0622
|RESTRAINT-1/2"
|
|''Grip size .450" to .560"''
|1
|-
|3
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|1
|-
|4
|E0650
|RECEPTACLE-DUPLEX
|
|''† 20A''
|1
|-
|5
|E0651
|COVER-RECEPTACLE-DUPLEX
|
|
|1
|-
|6
|E0655
|RECEPTACLE-GFCI
|
|''20A''
|1
|-
|7
|E0656
|COVER-RECEPTACLE-GFCI
|
|
|1
|-
|8
|E0654
|JUNCTION BOX-4" X 4" X 2"
|
|
|1
|-
|9
|E0657
|COVER-RECEPTACLE-DUPLEX/GFCI
|
|
|1
|-
|10
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|''Mounting hardware (Not shown)''
|A/R
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† If Duplex Receptacle has Split Feed (1 set of black & white wires for each plug), the Break-Off Fin must be removed prior to installation.''
|}

=== <big>'''Console Enclosure'''</big> ===

==== '''<big>''[Discontinued] Operator Console Enclosure for Units with 10 HP Power Unit''</big>''' ====
[[File:BE-TS (Discontinued) Operator Console Enclosure for Units with 10 HP Power Unit.png|alt=BE-TS (Discontinued) Operator Console Enclosure for Units with 10 HP Power Unit|frameless|548x548px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|N/A
|ENCLOSURE-6" X 6" X 4 "
|
|''Consult factory''
|1
|-
|2
|E0622
|RESTRAINT-1/2"
|
|''Grip size .450" to .560"''
|1
|-
|3
|E0608-1
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .450" to .560"''
|2
|-
|4
|E0623
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .250" to .375"''
|2
|-
|5
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|1
|-
|6
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|4
|-
|7
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|6
|-
|8
|43817087-2
|BRACKET-MOUNTING-ENCLOSURE
|
|
|1
|-
|9
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
| rowspan="4" |''Mounting bracket hardware (Not shown)''
|2
|-
|10
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|4
|-
|11
|HW0103
|WASHER-LOCK-1/4"
|
|2
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|2
|}
'''<big>''[Discontinued] Operator Console Enclosure Panel for Units with 10 HP Power Unit''</big>'''

[[File:BE-TS (Discontinued) Operator Console Enclosure Panel for Units with 10 HP Power Unit.png|alt=BE-TS (Discontinued) Operator Console Enclosure Panel for Units with 10 HP Power Unit|frameless|566x566px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0639
|PANEL-COMPONENT MOUNTING
|
|''Without holes''
|1
|-
|2
|E1024
|TRACK-TERMINAL BLOCK
|
|''4 7/8" LG''
|1
|-
|3
|E1020
|TERMINAL BLOCK
|
|
|9
|-
|4
|E1330
|END ANCHOR
|
|
|2
|-
|5
|E1040
|END BARRIER
|
|
|1
|-
|6
|E0341
|GROUND LUG
|
|
|1
|-
|7
|HW0130
|SCREW-RHMS-#8-32 X 1/2"
|
|''2 for track mounting''
|3
|-
|8
|HW0132
|NUT-NILN-#8-32
|
|''2 for track mounting''
|3
|-
|9
|HW0133
|WASHER-FLAT-#8-SAE
|
|''2 for track mounting''
|3
|}
'''<big>''[Current] Operator Console Enclosure for Units with 20 HP Power Unit''</big>'''

[[File:BE-TS (Current) Operator Console Enclosure for Units with 20 HP Power Unit.png|alt=BE-TS (Current) Operator Console Enclosure for Units with 20 HP Power Unit|frameless|549x549px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|N/A
|ENCLOSURE-8" X 8" X 4"
|
|''Consult factory''
|1
|-
|2
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|3
|-
|3
|E0632
|RESTRAINT-3/4"
|
|''Grip size .625" to .750"''
|1
|-
|4
|E0608-1
|RESTRAINT-1/2"-90 DEG
|
|''† Grip size .450" to .560"''
|4
|-
|5
|E0623
|RESTRAINT-1/2"-90 DEG
|
|''†'' ''Grip size .250" to .375"''
|4
|-
|6
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|11
|-
|7
|E0618
|LOCKNUT-CONDUIT-3/4"
|
|
|1
|-
|8
|E1349
|SEAL-KNOCKOUT-1/2"
|
|''† See notes''
|A/R
|-
|9
|43037003-2
|BRACKET-MOUNTING-ENCLOSURE
|
|
|1
|-
|10
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|4
|-
|11
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
| rowspan="4" |''Mounting bracket hardware (Not shown)''
|2
|-
|12
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|4
|-
|13
|HW0103
|WASHER-LOCK-1/4"
|
|2
|-
|14
|HW0002
|NUT-HEX-1/4-20
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Restraints sold for machines equipped with all available options. Machines built without certain options will have Knockout Seals (Item #8) installed in place of restraints.''
|}
'''<big>''[Current] Operator Console Enclosure Panel for Units with 20 HP Power Unit''</big>'''

[[File:BE-TS (Current) Operator Console Enclosure Panel for Units with 20 HP Power Unit.png|alt=BE-TS (Current) Operator Console Enclosure Panel for Units with 20 HP Power Unit|frameless|527x527px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0135
|PANEL-COMPONENT MOUNTING
|
|''Blank panel without holes''
|1
|-
|2
|E0908
|MOUNTING RAIL
|
|''Sold by length''
|A/R
|-
|3
|YE0402
|TERMINAL BLOCK
|
|
|14
|-
|4
|YE0405
|END BARRIER
|
|
|2
|-
|5
|YE0406
|END ANCHOR
|
|
|2
|-
|6
|E1074
|JUMPER-2 POLE
|
|
|2
|-
|7
|E0130
|GROUND BAR-7 POSITION
|
|
|1
|-
|8
|HW1061
|SCREW-RHMS-#8-32 X 1"
|
|
|2
|-
|9
|HW0130
|SCREW-RHMS-#8-32 X 1/2"
|
| rowspan="3" |''Track and Wireway mounting hardware (Not shown)''
|2
|-
|10
|HW0133
|WASHER-FLAT-#8
|
|2
|-
|11
|HW0132
|NUT-NILN-#8-32
|
|4
|}

=== <big>'''Junction Box'''</big> ===
[[File:BE-TS Junction Box.png|alt=BE-TS Junction Box|frameless|539x539px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0611
|JUNCTION BOX-4" X 2" X 2"
|
|
|3
|-
|2
|E0612
|COVER-JUNCTION BOX
|
|
|3
|-
|3
|E0613
|RESTRAINT-3/4"
|
|''Grip size .500" to .625"''
|4
|-
|4
|E0632
|RESTRAINT-3/4"
|
|''Grip size .625" to .750"''
|2
|-
|5
|E0618
|LOCKNUT-CONDUIT-3/4"
|
|
|6
|-
|6
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|6
|}

==== '''''<big>Top Module Junction Box</big>''''' ====
[[File:BE-TS Top Module Junction Box.png|alt=BE-TS Top Module Junction Box|frameless|532x532px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E1329
|JUNCTION BOX-4" X 4" X 2"
|
|
|1
|-
|2
|E0662
|RESTRAINT-3/4"-LIQUID TIGHT
|
|''Includes Locknut''
|1
|-
|3
|E0632
|RESTRAINT-3/4"
|
|''Grip size .625" to .750"''
|1
|-
|4
|E0618
|LOCKNUT-CONDUIT-3/4"
|
|
|1
|-
|5
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|}

=== '''<big>Wiring Diagrams</big>''' ===

==== '''''<big>BE-TS with 10 HP Motor Wiring Diagram</big>''''' ====
[[File:BE-TS Wiring Diagram-10HP Motor.png|alt=BE-TS Wiring Diagram-10HP Motor|frameless|800x800px]]

==== '''''<big>BE-TS with Magnet and 10 HP Motor Wiring Diagram</big>''''' ====
[[File:BE-TS with Magnet and 10HP Motor Wiring Diagram.png|alt=BE-TS with Magnet and 10HP Motor Wiring Diagram|frameless|800x800px]]

==== '''''<big>BE-TS with Magnet and 20 HP Motor Wiring Diagram</big>''''' ====
[[File:BE-TS Magnet Wiring Diagram-20HP Motor.png|alt=BE-TS Magnet Wiring Diagram-20HP Motor|frameless|800x800px]]

[[File:BE-TS Magnet Wiring Diagram-20HP Motor-02.png|alt=BE-TS Magnet Wiring Diagram-20HP Motor-02|frameless|800x800px]]

[[File:BE-TS Magnet Wiring Diagram-20HP Motor-03.png|alt=BE-TS Magnet Wiring Diagram-20HP Motor-03|frameless|800x800px]]

[[File:BE-TS Magnet Wiring Diagram-20HP Motor-04.png|alt=BE-TS Magnet Wiring Diagram-20HP Motor-04|frameless|800x800px]]

== <big>Hydraulics</big> ==

=== '''<big>[Discontinued] 10 HP Power Unit</big>''' ===
[[File:(Discontinued) BE-TS Power Unit (10HP).png|alt=(Discontinued) BE-TS Power Unit (10HP)|frameless|553x553px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0011
|MOTOR-ELECTRIC-10HP
|
|
|1
|-
|2
|HC0326
|ADAPTER-PUMP TO MOTOR
|
|
|1
|-
|3
|HC0325
|PUMP-VANE-16 GPM
|
|''Variable displacement''
|1
|-
|4
|HC0327
|COUPLING BODY-1 3/8"
|
|''Motor end''
|1
|-
|5
|HC0329
|SPIDER-COUPLING INSERT
|
|
|1
|-
|6
|HC0328
|COUPLING BODY-7/8"
|
|''Pump end''
|1
|-
|7
|HW0502
|BOLT-HHCS-1/2-13 X 1 1/4"
|
|
|2
|-
|8
|HW0110
|WASHER-LOCK-1/2"
|
|
|2
|-
|9
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|2
|-
|10
|H1606
|ADAPTER-90 DEG-#8 JICM X #8 SAEM
|
|
|1
|-
|11
|H1549
|ADAPTER-#20 JICM X #24 SAEM
|
|
|1
|-
|12
|H1595
|ADAPTER-90 DEG-#20 JICM X #20 JICSW
|
|
|1
|-
|13
|H1609
|ADAPTER-90 DEG-#12 JICM X #16 SAEM
|
|
|1
|-
|14
|H1522
|ADAPTER-#12 JICSW X #12 SAEM
|
|
|1
|-
|15
|HC0260
|VALVE-MAIN SYSTEM RELIEF
|
|
|1
|-
|15a
|43846003
|REPLACEMENT CARTRIDGE
|
|''†† For Item 15 (Not shown)''
|A/R
|-
|16
|HC0318
|GAUGE-PRESSURE
|
|
|1
|-
|17
|H0206
|PLUG-#4 NPT
|
|
|1
|-
|18
|H1108
|ADAPTER-#10 JICM X #12 SAEM
|
|
|1
|-
|19
|H1522
|ADAPTER-#12 JICSW X #12 SAEM
|
|''† See note''
|1
|-
|20
|H1542
|ADAPTER-#12 JICM X #12 SAEM
|
|
|1
|-
|21
|HC0280
|VALVE-CHECK
|
|''† See note''
|1
|-
|22
|H1542
|ADAPTER-#12 JICM X #12 SAEM
|
|''† See note''
|1
|-
|23
|E0613
|RESTRAINT-3/4"
|
|''Grip size .500" to .625"''
|1
|-
|23a
|E0618
|LOCKNUT-CONDUIT-3/4"
|
|''For Item 23 (Not shown)''
|1
|-
|24
|HW0403
|BOLT-HHCS-3/8-16 X 1 1/4"
|
|
|4
|-
|25
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|8
|-
|26
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|27
|HW0005
|NUT-HEX-3/8-16
|
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Parts noted used on units built after April 2001.''
|-
| colspan="6" |''†† Cartridges are for replacement only.''
|}

=== '''<big>[Discontinued] 30 Gallon Reservoir</big>''' ===
[[File:(Discontinued) BE-TS 30 Gallon Reservoir.png|alt=(Discontinued) BE-TS 30 Gallon Reservoir|frameless|542x542px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43842001
|RESERVOIR-VERTICAL-30 GAL
|
|''Includes Items 1 through 8''
|1
|-
|1
|HC0542
|GASKET-CHANNEL
|
|''Sold by length''
|7'
|-
|2
|HC0340
|GAUGE-SIGHT
|
|''with Thermometer''
|1
|-
|3
|HC0306
|STRAINER-SUCTION
|
|
|1
|-
|4
|HC0308
|FILLER/BREATHER ASSEMBLY
|
|
|1
|-
|5
|HW0209
|SCREW-RHMS-10-32 X 1/2"
|
|
|6
|-
|6
|BI0110
|ELBOW-STR-90 DEG-#16 NPT
|
|
|1
|-
|7
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|8
|-
|8
|H0208
|PLUG-#12 NPT
|
|
|1
|-
|9
|H1590
|ADAPTER-90 DEG-#16 JICM X #16 FNPT
|
|
|1
|-
|10
|BI0102
|ELBOW-#12 FNPT
|
|
|1
|-
|11
|BI0020
|NIPPLE-#12 NPT X 3"
|
|
|1
|-
|12
|BI0301
|TEE-#12 FNPT
|
|
|2
|-
|13
|H1502
|ADAPTER-#8 JICM X #12 MNPT
|
|
|1
|-
|14
|BI0002
|NIPPLE-CLOSE-#12 NPT
|
|
|2
|-
|15
|HC0307
|RETURN LINE FILTER ASSEMBLY
|
|''Housing and Filter''
|1
|-
|16
|HC0317
|FILTER-RETURN LINE
|
|''Replacement filter''
|1
|-
|17
|H1509
|ADAPTER-#10 JICM X #12 MNPT
|
|
|2
|-
|18
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
| rowspan="4" |''Mounting hardware''

''(Not shown)''
|4
|-
|19
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|8
|-
|20
|HW0107
|WASHER-LOCK-3/8"
|
|4
|-
|21
|HW0005
|NUT-HEX-3/8-16
|
|4
|}

=== '''<big>[Current] Power Unit (20 HP)</big>''' ===
[[File:(Current) BE-TS 30 Power Unit (20 HP).png|alt=(Current) BE-TS 30 Power Unit (20 HP)|frameless|531x531px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0040
|MOTOR-ELECTRIC-20 HP
|
|
|1
|-
|2
|HC0357
|ADAPTER-PUMP TO MOTOR
|
|
|1
|-
|3
|HC0356
|PUMP-PISTON-71CC
|
|
|1
|-
|4
|HC0358-M
|COUPLING BODY-M300-1 5/8" BORE
|
|''MOTOR SIDE''
|1
|-
|5
|HC0358-I
|SPIDER-COUPLING INSERT
|
|
|1
|-
|6
|HC0358-P
|COUPLING BODY-M300-1 1/4" BORE
|
|''PUMP SIDE''
|1
|-
|7
|HW0602
|BOLT-HHCS-5/8-11 X 2"
|
|
|2
|-
|8
|HW0113
|WASHER-LOCK-5/8"
|
|
|2
|-
|9
|H1604
|ADAPTER-90 DEG-#12 JICM X #10 SAEM
|
|
|1
|-
|10
|HC0363
|ADAPTER-FLANGE-#32 NPT
|
|''Includes O-ring''
|1
|-
|11
|HC0240
|BLOCK-CHECK VALVE
|
|''Includes Cartridge & O-ring''
|1
|-
|12
|N/A
|CARTRIDGE-CHECK VALVE
|
|''† Replacement cartridge''
|A/R
|-
|13
|H0300
|ELBOW-STR-90 DEG-#4 NPT
|
|
|1
|-
|14
|HC0318
|GAUGE-PRESSURE
|
|
|1
|-
|15
|HE0704
|ADAPTER-SPLIT FLANGE-1"
|
|''2-Piece adapter with O-ring''
|1
|-
|16
|HW0107
|WASHER-LOCK-3/8"
|
|
|2
|-
|17
|H0211
|ADAPTER-#24 NPT X #12
|
|
|1
|-
|18
|E0661
|RESTRAINT-3/4"-90 DEG-LIQUID TIGHT
|
|
|1
|-
|19
|HW0513
|BOLT-HHCS-1/2-13 X 2 1/4"
|
|
|4
|-
|20
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|8
|-
|21
|HW0110
|WASHER-LOCK-1/2"
|
|
|4
|-
|22
|HW0007
|NUT-HEX-1/2-13
|
|
|4
|-
! colspan="6" |NOTE
|-
| colspan="6" |''† Consult factory''
|}

=== '''<big>[Current] 45 Gallon Reservoir</big>''' ===
[[File:(Current) BE-TS 45 Gallon Reservoir.png|alt=(Current) BE-TS 45 Gallon Reservoir|frameless|547x547px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43842010
|45 GAL RESERVOIR ASSEMBLY
|
|''Includes Items 1 through 7''
|A/R
|-
|1
|43848005
|PLATE-COVER
|
|''† See note''
|1
|-
|2
|HC0308
|FILLER/BREATHER ASSEMBLY
|
|
|1
|-
|3
|HW0209
|SCREW-RHMS-10-32 X 1/2"
|
|
|6
|-
|4
|HC0340
|GAUGE-SIGHT
|
|
|1
|-
|5
|H0208
|PLUG-#12 NPT
|
|''Non-IIoT equipped units only''
|1
|-
|6
|HW0302
|BOLT-HHCS-1/4-20 X 3/4"
|
|
|8
|-
|7
|HW0104
|WASHER-FLAT-1/4"
|
|
|8
|-
|8
|HC0361
|HOUSING-FILTER
|
|
|1
|-
|9
|HC0354
|CARTRIDGE-FILTER
|
|''10 Micron filtration''
|1
|-
|10
|HC0362
|FLANGE-SUCTION TUBE
|
|''Includes hardware''
|1
|-
|11
|43848008
|TUBE-SUCTION
|
|
|1
|-
|12
|H1569
|ADAPTER-45 DEG-#12 JICM X #12 NPT
|
|
|1
|-
|13
|H0202
|REDUCER-#24 SAE X #12 SAE
|
|
|1
|-
|14
|H1622
|ADAPTER-90 DEG-#12 SAEM X #12 JICM
|
|
|1
|-
|15
|H1644
|PLUG-#24 SAE
|
|
|1
|-
|16
|HW0403
|BOLT-HHCS-3/8-16 X 1 1/4"
|
|
|4
|-
|17
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|18
|H1610
|ADAPTER-45 DEG-#12 JICSW X #12 JICM
|
|
|1
|-
|19
|PB0311-1
|NIPPLE-#12 NPT X 2"-BRASS
|
| rowspan="3" |''†† See notes''
|1
|-
|20
|BI0301
|TEE-#12 FNPT
|
|1
|-
|21
|H1502
|ADAPTER-#8 JICM X #12 MNPT
|
|2
|-
|22
|HW0403
|BOLT-HHCS-3/8-16 X 1 1/4"
|
| rowspan="5" |''Reservoir mounting hardware''

''(Not shown)''
|2
|-
|23
|HW0405
|BOLT-HHCS-3/8-16 X 2"
|
|2
|-
|24
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|8
|-
|25
|HW0107
|WASHER-LOCK-3/8"
|
|4
|-
|26
|HW0005
|NUT-HEX-3/8-16
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† RVT silicone required to seal cover plate after removal.''
|-
| colspan="6" |''†† Components required for units equipped with radial piston drive wheel motors plumbed with case drain hoses. See [https://tech.bhs1.com/index.php/(BE-TS)_Triple_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-401)#Drive_Wheel_Assembly Drive Wheel Assembly] section.''
|}

=== '''<big>Valve Assembly</big>''' ===

==== '''''<big>Lift Valve and Manifold Detail</big>''''' ====
[[File:BE-TS Lift Valve and Manifold.png|alt=BE-TS Lift Valve and Manifold|frameless|551x551px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|80342001
|LEVER VALVE RETRO KIT
|
|''† Required prior to 2006''
|A/R
|-
|1
|HC0257
|VALVE-LEVER
|
|''Effective from 2006 to Present''
|1
|-
|2
|HC0252
|MANIFOLD-D05-1 BANK
|
|
|1
|-
|3
|HW0318
|BOLT-SHCS-1/4-20 X 1 1/2"
|
|
|4
|-
|4
|H1642
|PLUG-#12 SAE
|
|
|1
|-
|5
|H1542
|ADAPTER-#12 JICM X #12 SAEM
|
|
|3
|-
|6
|H1606
|ADAPTER-90 DEG-#8 JICM X #8 SAEM
|
|
|2
|-
|7
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|8
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|8
|-
|9
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|10
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|11
|HC0248
|FIXED FLOW REGULATOR
|
|''††14 GPM''
|1
|-
|12
|H1521
|ADAPTER-#8 JICSW X #8 SAEM
|
|''†† See notes''
|1
|-
|13
|H1540
|ADAPTER-#8 JICM X #8 SAEM
|
|''†† See notes''
|1
|-
|14
|43817085
|PLATE-ADAPTER-VALVE
|
|''† Not shown''
|1
|-
|15
|SS0104
|BOLT-SHCS-1/4-20 X 5/8"-SST
|
|''† Not shown''
|4
|-
|16
|SS0300
|WASHER-FLAT-1/4"-SAE-SST
|
|''† Not shown''
|4
|-
! colspan="6" |
|-
| colspan="6" |''† Kit includes Items 1 & 14 through 16. Minor modifications to the dash board required.''
|-
| colspan="6" |''†† For units shipped April 2017 to present''
|}

==== '''''<big>Floor Drive / Arm Rotation Valve and Manifold Detail</big>''''' ====
[[File:BE-TS Floor Drive-Arm Rotation Valve and Manifold.png|alt=BE-TS Floor Drive-Arm Rotation Valve and Manifold|frameless|570x570px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0233
|VALVE-LEVER
|
|
|2
|-
|2
|HC0251
|MANIFOLD-D03-2 BANK
|
|
|1
|-
|3
|H1545
|ADAPTER-#10 JICM X #10 SAEM
|
|
|4
|-
|4
|H1606
|ADAPTER-90 DEG-#8 JICM X #8 SAEM
|
|
|2
|-
|5
|H1600
|ADAPTER-90 DEG-#6 JICM X #8 SAEM
|
|
|2
|-
|6
|H1587
|ADAPTER-#6 JICSW X #4 MNPT
|
|
|2
|-
|7
|HC0211
|VALVE-ADJUSTABLE FLOW CONTROL
|
|
|2
|-
|8
|H1504
|ADAPTER-#6 JICM X #4 MNPT
|
|
|2
|-
|9
|H1640
|PLUG-#6 SAE
|
|
|1
|-
|10
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|4
|-
|11
|43817033-2
|RISER PLATE
|
|
|1
|-
|12
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|13
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|8
|-
|14
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|15
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|16
|HC0233-SK
|SEAL KIT
|
|''For Item 1 (Not shown)''
|A/R
|}

==== '''''<big>Valve Assembly</big>''''' ====
[[File:BE-TS Valve Assembly.png|alt=BE-TS Valve Assembly|frameless|538x538px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0233
|VALVE-LEVER
|
|
|3
|-
|2
|HC0250
|MANIFOLD-D03-3 BANK
|
|
|1
|-
|3
|H1610
|ADAPTER-90 DEG-#10 JICM X #10 SAEM
|
|
|2
|-
|4
|H1641
|PLUG-#10 SAE
|
|
|1
|-
|5
|H1000
|ADAPTER-#8 SAEM X #4 FNPT
|
|
|4
|-
|6
|H0001
|NIPPLE-#4 NPT
|
|
|4
|-
|7
|HC0247
|FIXED FLOW REGULATOR-2.25 GPM
|
|''† See notes''
|4
|-
|8
|H1504
|ADAPTER-#6 JICM X #4 MNPT
|
|
|4
|-
|9
|H1640
|PLUG-#6 SAE
|
|
|1
|-
|10
|H1540
|ADAPTER-#8 JICM X #8 SAEM
|
|
|2
|-
|11
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|4
|-
|12
|43817034-2
|RISER PLATE
|
|
|1
|-
|13
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|14
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|8
|-
|15
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|16
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|17
|HC0233-SK
|SEAL KIT
|
|''For Item 1 (Not shown)''
|A/R
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Units built prior to January 2107 equipped with Adjustable Flow Controls. Fixed Flow Regulators are direct replacement for Adjustable Flow Controls.''
|}

=== '''<big>Lift Cylinder</big>''' ===
[[File:BE-TS Lift Cylinder.png|alt=BE-TS Lift Cylinder|frameless|582x582px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43822006
|CLEVIS ASSEMBLY
|
|''Sold as assembly only''
|4
|-
|2
|HW0813
|SCREW-SHSS-3/8-16 X 1/2"
|
|''Nylon tipped''
|8
|-
|3
|HC0420
|CYLINDER-LIFT
|
|
|4
|-
|4
|H1606
|ADAPTER-90 DEG-#8 JICM X #8 SAEM
|
|
|4
|-
|5
|H1645
|ADAPTER-90 DEG-#8 SAEM X #6 FNPT
|
|
|4
|-
|6
|H0212
|ADAPTER-#6 NPT X #8 FNPT
|
|
|4
|-
|7
|HC0425
|VELOCITY FUSE
|
|
|4
|}

=== '''<big>Lift Circuit</big>''' ===
[[File:BE-TS Lift Circuit.png|alt=BE-TS Lift Circuit|frameless|553x553px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43017014-2
|SUPPORT-PILOT DOWN MANIFOLD
|
|
|1
|-
|2
|43718008
|STANDOFF
|
|
|1
|-
|3
|HW0308
|BOLT-HHCS-1/4-20 X 2 1/2"
|
|
|2
|-
|4
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|2
|-
|5
|HW0315
|BOLT-HHCS-1/4-20 X 4 1/2"
|
|
|1
|-
|6
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|10
|-
|7
|HW0103
|WASHER-LOCK-1/4"
|
|
|5
|-
|8
|HW0002
|NUT-HEX-1/4-20
|
|
|5
|}

==== '''''<big>[Discontinued] Lift Circuit Configuration</big>''''' ====
[[File:(Discontinued) BE-TS Lift Circuit Configuration.png|alt=(Discontinued) BE-TS Lift Circuit Configuration|frameless|507x507px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|H1507
|ADAPTER-#8 JICM X #8 MNPT
|
|
|1
|-
|2
|H1521
|ADAPTER-#8 JICSW X #8 SAEM
|
|
|1
|-
|3
|HC0264
|VALVE-CHECK-PILOT TO OPEN
|
|
|1
|-
|4
|H1606
|ADAPTER-90 DEG-#8 JICM X #8 SAEM
|
|
|1
|-
|5
|H1621
|ADAPTER-#4 SAEM X #2 NPT
|
|
|1
|-
|6
|HC0269
|VALVE-ADJUSTABLE FLOW CONTROL
|
|
|1
|-
|7
|H1591
|ADAPTER-90 DEG-#6 JICM X #2 MNPT
|
|
|1
|-
|8
|H1587
|ADAPTER-#6 JICSW X #4 MNPT
|
|
|1
|-
|9
|H1501
|ADAPTER-#8 JICM X #6 MNPT
|
|
|2
|-
|10
|43047002
|MANIFOLD-PILOT DOWN
|
|
|1
|-
|11
|H1579
|ADAPTER-90 DEG-#6 JICM X #4 MNPT
|
|
|2
|}

==== '''''<big>[Current] Lift Circuit Configuration</big>''''' ====
[[File:(Current) BE-TS Lift Circuit Configuration.png|alt=(Current) BE-TS Lift Circuit Configuration|frameless|534x534px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0215
|VALVE-CHECK-CARTRIDGE
|
|
|8
|-
|2
|H1560
|ADAPTER-45 DEG-#8 JICM X #8 SAEM
|
|
|4
|-
|3
|H1670
|ADAPTER-45 DEG-#12 JICM X #10 SAEM
|
|
|1
|-
|4
|H1612
|ADAPTER-90 DEG-#8 JICM X #10 SAEM
|
|
|1
|-
|5
|HC0283
|VALVE-COUNTER BALANCE
|
|''Includes cartridge''
|1
|-
|6
|43846004
|CARTRIDGE-COUNTER BALANCE
|
|''Replacement cartridge''
|A/R
|-
|7
|H1552
|ADAPTER-#6 JICM X #6 SAEM
|
|
|1
|-
|8
|H1587
|ADAPTER-#6 JICSW X #4 MNPT
|
|
|1
|-
|9
|H1501
|ADAPTER-#8 JICM X #6 MNPT
|
|
|2
|-
|10
|43047002
|MANIFOLD-PILOT DOWN
|
|
|1
|-
|11
|H1579
|ADAPTER-90 DEG-#6 JICM X #4 MNPT
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Cartridges are for replacement only''
|}

==== '''''<big>Down-Speed Flow Control</big>''''' ====
[[File:BE-TS Down-Speed Flow Control.png|alt=BE-TS Down-Speed Flow Control|frameless|551x551px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0270
|VALVE-ADJUSTABLE FLOW CONTROL
|
|''Pressure compensated''
|1
|-
|2
|H0007
|NIPPLE-#8 NPT
|
|
|1
|-
|3
|H1647
|ADAPTER-90 DEG-#10 SAEM X #8 FNPT
|
|
|1
|-
|4
|H1680
|ADAPTER-#10 JICM X #8 MNPT
|
|
|1
|-
|5
|H1690
|ADAPTER-#10 JICSW X #10 SAEM
|
|
|1
|-
|6
|HC0248
|FIXED FLOW REGULATOR
|
|''14 GPM''
|1
|-
|7
|H1521
|ADAPTER-#8 JICSW X #8 SAEM
|
|
|2
|-
|8
|H1612
|ADAPTER-90 DEG-#8 JICM X #10 SAEM
|
|
|1
|-
|9
|H1547
|ADAPTER-#8 JICM X #10 SAEM
|
|
|1
|}

=== '''<big>Cross Port Relief</big>''' ===

==== '''''<big>Mounting Configuration</big>''''' ====
[[File:BE-TS Cross Port Relief Mounting Configuration.png|alt=BE-TS Cross Port Relief Mounting Configuration|frameless|546x546px]]
{| class="wikitable"
! colspan="6" |UNITS BUILT PRIOR TO SEPTEMBER, 2014
|-
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HW0308
|BOLT-HHCS-1/4-20 X 2 1/2"
|
|
|2
|-
|2
|<nowiki>-</nowiki>
|<nowiki>-</nowiki>
|
|
|<nowiki>-</nowiki>
|-
|3
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|4
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|5
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|-
|6
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|}
{| class="wikitable"
! colspan="6" |UNITS BUILT SEPTEMBER, 2014 TO DECEMBER, 2014
|-
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HW0308
|BOLT-HHCS-1/4-20 X 2 1/2"
|
|
|2
|-
|2
|HW0305
|BOLT-HHCS-1/4-20 X 2"
|
|
|2
|-
|3
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|8
|-
|4
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|5
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|6
|<nowiki>-</nowiki>
|<nowiki>-</nowiki>
|
|
|<nowiki>-</nowiki>
|-
|7
|43058004
|PLATE-SPACER
|
|
|1
|}
{| class="wikitable"
! colspan="6" |UNITS BUILT DECEMBER, 2014 TO PRESENT
|-
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HW0308
|BOLT-HHCS-1/4-20 X 2 1/2"
|
|
|4
|-
|2
|<nowiki>-</nowiki>
|<nowiki>-</nowiki>
|
|
|<nowiki>-</nowiki>
|-
|3
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|8
|-
|4
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|5
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|}
''NOTE: Effectivity dates refer to dates new extractor units shipped from the factory. Replacement part effectivity may differ due to factory inventory levels at time of parts order. Consult factory if unsure of parts needed.''

==== '''''<big>Components</big>''''' ====
[[File:BE-TS Cross Port Relief Components.png|alt=BE-TS Cross Port Relief Components|frameless|539x539px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0262
|VALVE-CROSS PORT RELIEF
|
|''Includes cartridges''
|1
|-
|2
|43046002
|REPLACEMENT CARTRIDGE
|
|''For Item 1''
|A/R
|-
|3
|H1540
|ADAPTER-#8 JICM X #8 SAEM
|
|
|2
|-
|4
|H1521
|ADAPTER-#8 JICSW X #8 SAEM
|
|
|3
|-
|5
|H1507
|ADAPTER-#8 JICM X #8 MNPT
|
|
|3
|-
|6
|HC0239
|VALVE-ADJUSTABLE FLOW CONTROL
|
|
|2
|-
|7
|H1568
|ADAPTER-45 DEG-#8 JICM X #8 MNPT
|
|
|1
|-
|8
|H1646
|ADAPTER-90 DEG-#8 SAEM X #6 FNPT
|
|
|2
|-
|9
|H0805
|TEE-#6 MNPT
|
|
|2
|-
|10
|HC0273
|REGULATOR-FIXED FLOW
|
|''7.0 GPM''
|4
|-
|11
|H1501
|ADAPTER-#8 JICM X #6 MNPT
|
|
|4
|}

=== '''<big>Floor Drive Cutout</big>''' ===
[[File:BE-TS Floor Drive Cutout.png|alt=BE-TS Floor Drive Cutout|frameless|545x545px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|N/A
|SOLENOID-DRIVE CUTOUT
|
|''† See notes''
|1
|-
|2
|H1521
|ADAPTER-#8 JICSW X #8 SAEM
|
|
|1
|-
|3
|H1606
|ADAPTER-90 DEG-#8 JICM X #8 SAEM
|
|
|1
|-
|4
|E0611
|JUNCTION BOX-4" X 2" X 2"
|
|
|1
|-
|5
|E0612
|COVER-JUNCTION BOX
|
|
|1
|-
|6
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|2
|-
|7
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|2
|-
|8
|BI0001
|NIPPLE-CLOSE-#8 NPT
|
|
|1
|-
|9
|N/A
|SOLENOID-DRIVE CUTOUT
|
|''† See notes''
|1
|-
|10
|YE0501
|CONNECTOR-SOLENOID
|
|''DIN 43650''
|1
|-
|11
|43058004
|PLATE-SPACER
|
|
|1
|-
|12
|HC0278-TS/QS
|SOLENOID-DRIVE CUTOUT
|
|
|1
|-
|13
|H1547
|ADAPTER-#8 JICM X #10 SAEM
|
|
|1
|-
|14
|H1612
|ADAPTER-90 DEG-#8 JICM X #10 SAEM
|
|
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Part obsolete. Must be replaced with Retro Kit Part # 80242007.''
|-
| colspan="6" |''NOTE: Effectivity dates refer to dates new extractor units shipped from the factory. Replacement part effectivity may differ due to factory inventory levels at time of parts order. Consult factory if unsure of parts needed.''
|}

=== '''<big>Counter Balance Valve</big>''' ===
[[File:BE-TS Counter Balance Valve.png|alt=BE-TS Counter Balance Valve|frameless|554x554px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0263
|VALVE-COUNTER BALANCE
|
|
|1
|-
|1a
|43046004
|REPLACEMENT CARTRIDGE
|
|''† For Item 1 (Not shown)''
|A/R
|-
|2
|H1615
|ADAPTER-90 DEG-#6 JICM X #6 SAEM
|
|
|2
|-
|3
|H1552
|ADAPTER-#6 JICM X #6 SAEM
|
|
|2
|-
|4
|HW0305
|BOLT-HHCS-1/4-20 X 2"
|
|
|2
|-
|5
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|6
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|7
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Cartridges are for replacement only''
|}

=== '''<big>Transition Plate</big>''' ===
[[File:BE-TS Transition Plate.png|alt=BE-TS Transition Plate|frameless|576x576px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43817067-2
|PLATE-TRANSITION
|
|
|1
|-
|2
|H0020
|UNION-BULKHEAD-45 DEG-#6 JICM
|
|
|8
|-
|3
|H0021
|NUT-BULKHEAD-#6 JIC
|
|
|8
|-
|4
|PL0501
|GROMMET-1/2" I.D.
|
|
|1
|-
|5
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|2
|-
|6
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|7
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|8
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|}

=== '''<big>Return Line Manifold</big>''' ===
[[File:BE-TS Return Line Manifold.png|alt=BE-TS Return Line Manifold|frameless|555x555px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43847001
|MANIFOLD-RETURN LINE
|
|
|1
|-
|2
|H1501
|ADAPTER-#8 JICM X #6 MNPT
|
|
|1
|-
|3
|H1503
|ADAPTER-#12 JICM X #12 MNPT
|
|
|2
|-
|4
|HW0308
|BOLT-HHCS-1/4-20 X 2 1/2"
|
|
|2
|-
|5
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|6
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|7
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|-
|8
|43817069-2
|BRACKET-BULKHEAD
|
|
|1
|-
|9
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
|10
|H0015
|UNION-BULKHEAD-90 DEG-#12 JICM
|
|
|1
|-
|11
|H0016
|NUT-BULKHEAD-#12 JIC
|
|
|1
|}

=== '''<big>EQ Chain Hose Guard</big>''' ===
[[File:BE-TS EQ Chain Hose Guard.png|alt=BE-TS EQ Chain Hose Guard|frameless|577x577px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43017074-2
|GUARD-HOSE-EQ CHAIN
|
|''† See notes''
|1
|-
|2
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Used on units manufactured after May 2015.''
|}

=== '''<big>Hydraulic Schematics</big>''' ===
[[File:BE-TS Hydraulic Schematic.png|alt=BE-TS Hydraulic Schematic|frameless|1180x1180px]]

==== '''''<big>Extended Reach Hydraulic Schematics</big>''''' ====
[[File:BE-TS Hydraulic Schematic Extended Reach.png|alt=BE-TS Hydraulic Schematic Extended Reach|frameless|905x905px]]

== <big>Standard Available Options</big> ==

=== '''<big>Strobe & Alarm</big>''' ===

==== '''<big>''[Discontinued] Strobe Light & Stanchion Configuration''</big>''' ====
[[File:(Discontinued) BE-TS Strobe Light.png|alt=(Discontinued) BE-TS Strobe Light|frameless|722x722px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0317
|STROBE LIGHT
|
|
|1
|-
|2
|41215014
|STANCHION
|
|
|1
|-
|3
|HW0401
|BOLT-HHCS-3/8-16 X 1"
|
|
|3
|-
|4
|HW0107
|WASHER-LOCK-3/8"
|
|
|3
|-
|5
|HW0108
|WASHER-FLAT-3/8"
|
|
|3
|-
|6
|E1010
|RECEPTACLE-TWIST LOCK
|
|''(Not shown)''
|1
|-
|7
|E1011
|PLUG-TWIST LOCK
|
|''(Not shown)''
|1
|}

==== '''<big>''[Discontinued] Audible Alarm Configuration''</big>''' ====
[[File:(Discontinued) BE-TS Audible Alarm.png|alt=(Discontinued) BE-TS Audible Alarm|frameless|490x490px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0317-A
|AUDIBLE ALARM
|
|
|1
|-
|2
|E0654
|JUNCTION BOX-4" X 4" X 2"
|
|
|1
|-
|3
|00117101-2
|MOUNTING BRACKET
|
|
|1
|-
|4
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|1
|-
|5
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|1
|-
|6
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|4
|}

==== '''<big>''[Current] Stack Light Strobe & Alarm Configuration''</big>''' ====
[[File:(Current) BE-TS Stack Light Strobe and Alarm Configuration.png|alt=(Current) BE-TS Stack Light Strobe and Alarm Configuration|frameless|844x844px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0362
|MOUNTING BASE
|
|''Includes restraints''
|1
|-
|2
|E0365
|TERMINAL BASE
|
|
|1
|-
|3
|E0363
|STROBE LIGHT-AMBER-120VAC
|
|''† See notes''
|1
|-
|4
|E0364
|AUDIBLE ALARM
|
|''†† See notes''
|1
|-
|5
|SS0118
|SCREW-SHCS-#8-32 X 1"
|
|
|2
|-
|6
|SS0303
|WASHER-FLAT-#8
|
|
|2
|-
|7
|SS0203
|NUT-NILN-#8-32
|
|
|2
|-
|8
|E1010
|RECEPTACLE-TWIST LOCK
|
|''(Not shown)''
|1
|-
|9
|E1011
|PLUG-TWIST LOCK
|
|''(Not shown)''
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† For units not equipped with the audible alarm option, a cap (not shown) mounts on top of the strobe light in place of the audible alarm. Cap included with base.''
|-
| colspan="6" |''†† For units not equipped with the strobe light option, the audible alarm mounts directly to the terminal base in place of the strobe light.''
|}

==== '''<big>''Strobe & Alarm Mounting''</big>''' ====
[[File:BE-TS Strobe and Alarm Mounting.png|alt=BE-TS Strobe and Alarm Mounting|frameless|516x516px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41235060
|STACK LIGHT STANCHION
|
|''Discontinued''
|A/R
|-
|2
|HW0401
|BOLT-HHCS-3/8-16 X 1"
|
|
|3
|-
|3
|HW0107
|WASHER-LOCK-3/8"
|
|
|3
|-
|4
|HW0108
|WASHER-FLAT-3/8"
|
|
|3
|-
|REF
|43032006
|STANCHION ASSEMBLY
|
|''Includes items 5 through 8''
|A/R
|-
|5
|43035003
|STACK LIGHT STANCHION
|
|
|1
|-
|6
|43037007-2
|CLAMP BRACKET
|
|
|1
|-
|7
|HW0305
|BOLT-HHCS-1/4-20 X 2"
|
|
|4
|-
|8
|HW0050
|NUT-FLANGED-1/4-20
|
|
|4
|-
|9
|43037004-2
|MOUNTING BRACKET
|
|''Overhead Guard only''
|1
|-
|10
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|}

=== '''<big>Horn</big>''' ===
[[File:BE-TS Horn.png|alt=BE-TS Horn|frameless|565x565px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|YE0308
|BUTTON-HORN
|
|
|1
|-
|2
|E0317-A
|AUDIBLE ALARM
|
|
|1
|-
|3
|E0654
|JUNCTION BOX-4" X 4" X 2"
|
|
|1
|-
|4
|00117101-2
|MOUNTING BRACKET
|
|
|1
|-
|5
|HW0302
|BOLT-HHCS-1/4-20 X 3/4"
|
|
|2
|-
|6
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|2
|-
|7
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|8
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|-
|9
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
|10
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|1
|-
|11
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|1
|}

=== '''<big>Overhead Guard</big>''' ===
[[File:BE-TS Overhead Guard.png|alt=BE-TS Overhead Guard|frameless|530x530px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43817119-2
|GUARD-SIDE
|
|''† See notes''
|2
|-
|2
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|8
|-
|3
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|8
|-
|4
|HW0406
|BOLT-HHCS-3/8-16 X 2-1/2"
|
|
|5
|-
|5
|HW0108
|WASHER-FLAT-3/8"
|
|
|10
|-
|6
|HW0006
|NUT-NILN-3/8-16
|
|
|5
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Side Guards used on units built November 2013 to Present. Mounting hardware valid for all units with Removable Overhead Guard.''
|}

=== '''<big>Operator Sheild</big>''' ===

==== '''<big>''[Current] Operator Shield''</big>''' ====
[[File:(Current) BE-TS 30 Operator Sheild.png|alt=(Current) BE-TS 30 Operator Sheild|frameless|566x566px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43814025
|OPERATOR SHIELD
|
|''† See notes''
|1
|-
|2
|HC0542
|GASKET EDGING
|
|''(2) @ 38" LG, (1) @ 60" LG''
|136"
|-
|3
|43817116-2
|BRACKET-TOP
|
|
|1
|-
|4
|1412FSW
|BOLT-SELF TAP "F"-1/4-20 X 3/4"
|
|
|2
|-
|5
|43817117-2
|BRACKET-CENTER SUPPORT-OUTSIDE
|
|
|1
|-
|6
|43817118-2
|BRACKET-CENTER SUPPORT-INSIDE
|
|
|1
|-
|7
|SS0114
|SCREW-RHMS-#10-24 X 1/2"
|
|
|3
|-
|8
|SS0502
|LANYARD-8"
|
|
|2
|-
|9
|SS0501
|PIN-QUICK RELEASE-3/16" X 2"
|
|
|2
|-
|10
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Consult factory for units built prior to November 2013 with plexiglass bolted directly to Overhead Guard structure on front and sides.''
|}

==== '''<big>''Operator Shield (Used Prior to November 2013)''</big>''' ====
[[File:BE-TS Operator Shield (Used Prior to November 2013).png|alt=BE-TS Operator Shield (Used Prior to November 2013)|frameless|559x559px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43717116
|SHIELD-OPERATOR
|
|''† See notes''
|1
|-
|2
|43015010
|FRAME-OPERATOR SHIELD WELDMENT
|
|
|1
|-
|3
|43017066-2
|SUPPORT-SIDE
|
|
|2
|-
|4
|43017065-2
|SUPPORT-LOWER
|
|
|1
|-
|5
|43017067-2
|SUPPORT-UPPER
|
|
|1
|-
|6
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|16
|-
|7
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|32
|-
|8
|HW0103
|WASHER-LOCK-1/4"
|
|
|16
|-
|9
|HW0002
|NUT-HEX-1/4-20
|
|
|16
|-
|10
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|6
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Consult factory for units with plexiglass bolted directly to frame.''
|}

=== '''<big>Powered Roller Cutout</big>''' ===

==== '''''<big>Powered Roller Cutout Photo Eye & Reflector Locations (Prior to May 2022)</big>''''' ====
[[File:BE-TS Powered Roller Cutout Photo Eye & Reflector Locations.png|alt=BE-TS Powered Roller Cutout Photo Eye & Reflector Locations|frameless|557x557px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E1321A
|PHOTO EYE
|
|''† Polarized''
|1
|-
|2
|41217170-2
|MOUNT-PHOTO EYE
|
|
|1
|-
|3
|HW0216
|SCREW-#10-24 X 2"
|
|''†† See notes''
|2
|-
|4
|HW0032
|NUT-NILN-#10-24
|
|
|2
|-
|5
|E1321-R
|REFLECTOR
|
|
|1
|-
|6
|41217171
|MOUNT-REFLECTOR
|
|
|1
|-
|7
|SS0803
|SCREW-RHMS-#6-32 X 5/8"
|
|''†† See notes''
|2
|-
|8
|SS0125
|BOLT-HHCS-1/4-20 X 5/8"
|
|''††† See notes''
|4
|-
|9
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|10
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''Quantities provided are for Single-Sided (PRC-1) Power Roller Cutout option. For units with Double Sided (PRC-2) option, quantities are double.''
|-
| colspan="6" |''† Polarized Photo Eye recommended to prevent potential operational issues with very smooth or shiny battery cases.''
|-
| colspan="6" |''†† Photo Eye & Reflector mounting screws are trimmed to length.''
|-
| colspan="6" |''††† Photo Eye & Reflector Bracket Mounting Screws may be required to ground flush to prevent intereferance with guards.''
|}
'''''<big>Powered Roller Cutout Photo Eye & Reflector Locations (May 2022 to Present)</big>'''''

[[File:BE-TS Powered Roller Cutout Photo Eye & Reflector Locations (May 2022 to Present).png|alt=BE-TS Powered Roller Cutout Photo Eye & Reflector Locations (May 2022 to Present)|frameless|555x555px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E1321A
|PHOTO EYE
|
|''† Polarized''
|1
|-
|2
|13537001-2
|MOUNT-PHOTO EYE
|
|
|1
|-
|3
|E1321-R
|REFLECTOR
|
|
|1
|-
|4
|41217171
|MOUNT-REFLECTOR
|
|
|1
|-
|5
|SS0803
|SCREW-RHMS-#6-32 X 5/8"
|
|''†† See notes''
|2
|-
|6
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|4
|-
|7
|PL0506
|GROMMET-SEALING-2 1/2"
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''Quantities provided are for Single-Sided (PRC-1) Power Roller Cutout option. For units with Double Sided (PRC-2) option, quantities are double.''
|-
| colspan="6" |''† Polarized Photo Eye recommended to prevent potential operational issues with very smooth or shiny battery cases.''
|-
| colspan="6" |''†† Reflector mounting screws are trimmed to length.''
|}

==== '''''<big>Powered Roller Cutout Mounting</big>''''' ====
[[File:BE-TS Powered Roller Cutout Mounting.png|alt=BE-TS Powered Roller Cutout Mounting|frameless|557x557px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0281
|SOLENOID VALVE
|
|
|2
|-
|2
|E0611
|JUNCTION BOX-4" X 2" X 2"
|
|
|1
|-
|3
|E0612
|COVER-JUNCTION BOX
|
|
|1
|-
|4
|BI0001
|NIPPLE-CLOSE-#8 NPT
|
|
|2
|-
|5
|E0623
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .250" to .375"''
|1
|-
|6
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|3
|-
|7
|H1600
|ADAPTER-90 DEG-#6 JICM X #8 SAEM
|
|
|2
|-
|8
|H1546
|ADAPTER-#6 JICM X #8 SAEM
|
|
|2
|-
|9
|HW0308
|BOLT-HHCS-1/4-20 X 2 1/2"
|
|
|2
|-
|10
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|11
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|}

==== '''''<big>Powered Roller Cutout Override Button</big>''''' ====
[[File:BE-TS Powered Roller Cutout Override Button.png|alt=BE-TS Powered Roller Cutout Override Button|frameless|568x568px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|N/A
|ACTUATOR-PUSH BUTTON (DISCONTINUED)
|
|''† See notes''
|1
|-
|2
|N/A
|CONTACT BLOCK-N/C (DISCONTINUED)
|
|''† See notes''
|1
|-
|3
|E0384
|ACTUATOR-PUSH BUTTON
|80932002
|
|1
|-
|4
|E0386
|CONTACT BLOCK-N/C
|80932002
|
|1
|-
|5
|E0387
|DUMMY BLOCK
|80932002
|
|1
|-
|6
|E0388
|PUSH BUTTON-GREEN
|80932002
|
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''Button location on dash may vary from position shown.''
|-
| colspan="6" |''† Parts no longer available. Must order new Push-Button Switch Kit 80932002''
|}

==== '''''<big>Powered Roller Cutout Junction Box</big>''''' ====
[[File:BE-TS Powered Roller Cutout Junction Box.png|alt=BE-TS Powered Roller Cutout Junction Box|frameless|535x535px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0611
|JUNCTION BOX-4" X 2" X 2"
|
|
|1
|-
|2
|E0612
|COVER-JUNCTION BOX
|
|
|1
|-
|3
|E0623
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .250" to .375"''
|3
|-
|4
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|4
|-
|5
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|7
|-
|6
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|''Mounting bolts (Not shown)''
|4
|}

=== '''<big>Level Assist</big>''' ===
[[File:BE-TS Level Assist.png|alt=BE-TS Level Assist|frameless|568x568px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E1321A
|PHOTO EYE
|
|
|1
|-
|2
|13537001-2
|MOUNT-PHOTO EYE
|
|
|1
|-
|3
|PL0502
|GROMMET
|
|
|1
|-
|4
|43837007
|TARGET ANGLE
|
|
|1
|-
|5
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|4
|-
|6
|E0376
|INDICATOR LIGHT
|
|''† See notes''
|1
|-
|7
|HW0152
|WASHER-5/8" I.D.
|
|''†† See notes (Not shown)''
|2
|-
|8
|E1321-RT
|REFLECTIVE TAPE
|
|''(Not shown)''
|A/R
|-
! colspan="6" |NOTES
|-
| colspan="6" |''Location of Indicator Light on the dash may vary from location shown''
|-
| colspan="6" |''†† Extractors built prior to October 2021 used Multi-Piece Indicator Lights with Replaceable Bulb and Lens are no longer available. Current Indicator Light is a 1-Piece LED Assembly. Replacement of any Multi-Piece Component requires replacing entire assembly with current, 1-Piece Indicator Light.''
|-
| colspan="6" |''††† Washers required for units that did not ship with Level Assist option from the factory.''
|}
'''<big>''Level Assist Junction Box''</big>'''

[[File:BE-TS Level Assist Junction Box.png|alt=BE-TS Level Assist Junction Box|frameless|524x524px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0611
|JUNCTION BOX-4" X 2" X 2"
|
|
|1
|-
|2
|E0612
|COVER-JUNCTION BOX
|
|
|1
|-
|3
|E0623
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .250" to .375"''
|1
|-
|4
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|2
|-
|5
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|3
|-
|6
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|''Mounting bolts (Not shown)''
|2
|}

=== '''<big>Blue Light</big>''' ===
[[File:BE-TS Blue Light.png|alt=BE-TS Blue Light|frameless|611x611px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|EW2002B
|BLUE PROJECTION SPOTLIGHT
|
|
|2
|-
|2
|HW0401
|BOLT-HHCS-3/8-16 X 3/4"
|
|
|2
|-
|3
|HW0107
|WASHER-LOCK-3/4"
|
|
|2
|-
|4
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|4
|-
|5
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|4
|-
|6
|43835001
|STANCHION-POWER
|
|
|2
|}
[[File:BE-TS Blue Light Enclosure.png|alt=BE-TS Blue Light Enclosure|frameless|552x552px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|N/A
|ENCLOSURE-8" X 8" X 4"
|
|''Consult factory''
|1
|-
|2
|E0135
|PANEL-COMPONENT MOUNTING
|
|''Blank panel without holes''
|1
|-
|3
|PS5R-SC12
|POWER SUPPLY
|
|
|1
|-
|4
|E0908
|MOUNTING RAIL
|
|''Sold by length''
|A/R
|-
|5
|YE0402
|TERMINAL BLOCK
|
|
|4
|-
|6
|YE0405
|END BARRIER
|
|
|1
|-
|7
|YE0406
|END ANCHOR
|
|
|2
|-
|8
|E0341
|GROUND LUG
|
|
|1
|-
|9
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|3
|-
|10
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|3
|-
|11
|HW0130
|SCREW-RHMS-#8-32 X 1/2"
|
|''2 per Mounting Rail''
|5
|-
|12
|HW0132
|NUT-NILN-#8-32
|
|''2 per Mounting Rail''
|5
|-
|13
|HW0133
|WASHER-FLAT-#8-SAE
|
|''2 per Mounting Rail''
|5
|-
|14
|00196404
|LABEL-DANGER
|
|
|1
|}

=== '''<big>Water Cart</big>''' ===
[[File:BE-TS Water Cart.png|alt=BE-TS Water Cart|frameless|549x549px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|PB0033
|OVERFILL INDICATOR
|
|
|1
|-
|2
|PB0034
|LOCKNUT-CONDUIT-2"-NYLON
|
|
|1
|-
|3
|HC0308
|FILLER/BREATHER ASSEMBLY
|
|Includes gaskets
|1
|-
|4
|HW0209
|SCREW-RHMS-10-32 X 1/2"
|
|
|6
|-
|5
|550-057
|HOSE-FILL-3/4" X 15'
|
|
|1
|-
|6
|550-027
|ON/OFF VALVE
|
|''(Not shown)''
|1
|-
|7
|PB0902
|HOSE-3/4"
|
|
|30"
|-
|8
|HW1018
|HOSE CLAMP-3/4"
|
|
|1
|-
|9
|PB0603
|ADAPTER-3/4" NPT X 3/4" BARB
|
|
|1
|-
|10
|PB0456
|ELBOW-STR-90 DEG-3/4" NPT
|
|
|1
|-
|11
|PB0451
|ADAPTER-3/4" NPT X 3/4 GHT
|
|
|1
|-
|12
|PB0302
|PLUG-3/4" NPT
|
|
|
|-
|13
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|2
|-
|14
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|2
|-
|15
|SS0106
|SHCS-#10-24 X 1/2"-SST
|
|
|6
|-
|16
|SS0114
|BHSCS-#10-24 X 1/2" SST
|
|
|4
|-
|17
|SS0301
|WASHER-FLAT-#10-SAE-SST
|
|
|10
|-
|18
|00196701
|DECAL-BHS-12"
|
|
|1
|-
|19
|00196404
|LABEL-DANGER-"120 VOLTS"
|
|
|1
|-
|20
|00166648
|LABEL, NON-POTABLE
|
|
|1
|-
|21
|HW0418
|BOLT-HHCS-3/8-16 X 2-1/4"
|
| rowspan="3" |''Mounting bolts''

''(Not shown)''
|2
|-
|22
|HW0031
|NUT-HEX-3/8-16 CENTERLOCK
|
|4
|-
|23
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|2
|}
[[File:BE-TS Water Cart 2.png|alt=BE-TS Water Cart|frameless|539x539px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|PB0150
|PUMP-SUBMERSIBLE
|
|''† See notes''
|1
|-
|2
|HW1018
|HOSE CLAMP-3/4"
|
|
|1
|-
|3
|46932005
|LEVEL SWITCH CONDUIT ASSEMBLY
|
|''Includes (2) Item #4 and wiring''
|1
|-
|4
|E1381
|SWITCH-LIQUID LEVEL
|
|
|2
|-
|5
|SS0760
|HOSE CLAMP-4" TO 7"
|
|
|1
|-
|6
|HW1019
|HOSE CLAMP-1"
|
|
|2
|-
|7
|SS06010
|HANDLE
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Hose barb fitting modified at factory during assembly to remove threaded portion from hose barb end. Modification of fitting required prior to installing replacement pump.''
|}
[[File:BE-TS Water Cart 02.png|alt=BE-TS Water Cart 02|frameless|539x539px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E1511
|SWITCH-ROCKER
|
|''Submersible rated''
|1
|-
|2
|E0378
|INDICATOR LIGHT-120VAC-GREEN
|
|''† See notes''
|1
|-
|3
|E0376
|INDICATOR LIGHT-120VAC-AMBER
|
|''† See notes''
|1
|-
|4
|E0377
|INDICATOR LIGHT-120VAC-RED
|
|''† See notes''
|1
|-
|5
|46917015
|PLACARD-INDICATOR LIGHT
|
|
|1
|-
|6
|E0505
|16-3 SO CORD
|
|
|72"
|-
|7
|E0653
|PLUG-120V/15A
|
|
|1
|-
|8
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|1
|-
|9
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|1
|-
|10
|PL0501
|GROMMET-1/2"
|
|
|2
|-
|11
|E1313
|SOCKET-RELAY-8 PIN
|
|
|1
|-
|12
|E0331
|RELAY-DPDT-110VAC
|
|
|1
|-
|13
|E0440
|TERMINAL BLOCK-8 POLE
|
|
|1
|-
|14
|E1070
|GROUND BAR-4 POSITION
|
|
|1
|-
|15
|HW0139
|SCREW-RHMS-#8-32 X 1 1/4"
|
|
|2
|-
|16
|HW0135
|SCREW-RHMS-#8-32 X 3/4"
|
|
|2
|-
|17
|HW1061
|SCREW-RHMS-#8-32 X 1"
|
|
|1
|-
|18
|HW0132
|NUT-NILN-#8-32
|
|
|5
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Water carts built prior to October 2021 used Multi-Piece Indicator Lights with Replaceable Bulb and Lens and are no longer available. Current Indicator Lights are a 1-Piece LED Assemblly.''
''Replacement of any Mutli-Piece component requires replacing entire assembly with current 1-Piece Indicator Light.''
|}

= <big>Service & Maintenance</big> =

== <big>Daily Inspection List</big> ==
The points listed below should be visually inspected daily prior to initial start up of the Battery Extractor to ensure safe and proper operation of the unit and to help avoid unnecessary down time.

# Walk around unit and inspect for any physical damage to machine not previously noted.
# Verify all guards are in place.
# Inspect the AC power feed for any damage.
# Vacuum equipped units: Inspect vacuum cups for damage to cup sealing surface, backup casting, and vacuum hoses. Magnet equipped units: Inspect magnets for damage to attachment face, proximity sensor cover, cables and connections.
# Inspect travel path and area around unit for any hydraulic oil that could be a potential repair/maintenance issue and/or safety hazard.
# Check oil level in hydraulic reservoir at fill level gauge.
# Check that operator safety gate and all safety switches are in proper working order.
# Verify extractor path is free of obstructions.
# Check roller beds for any debris and clean as required.
# Board unit, engage system and verify all functions are operating properly and that no abnormal or unusual noises are present.

''* Use form IF-5008 when preforming daily inspections''

== <big>Operator's Daily Checklist</big> ==
[[File:BE-TS Operator's Daily Checklist.png|alt=BE-TS Operator's Daily Checklist|frameless|1180x1180px]]

== <big>Recommended Battery Extractor Lubrication Intervals</big> ==
{| class="wikitable"
!Lubrication Task
!'''# of Places'''
!Intervals
|-
|'''1. Lubricate grease fittings using #2 lithium based grease'''
|
|
|-
|A. Extractor arm drive nut and carrier bearings
|5 places
|50 hrs / Weekly
|-
|B. Idler casters
|2 places
|200 hrs / Weekly
|-
|'''2. Wipe off and lubricate chains using light machine oil'''
|
|
|-
|A. #80 Lift chains (Not applicable to BE-SL units)
|4 places
|200 hrs / Monthly
|-
|B. #60 Equalization chains
|4 places
|200 hrs / Monthly
|-
|C. #35 Powered roller chains
|8 places
|200 hrs / Monthly
|-
|'''3. Change return line hydraulic fluid filter'''
''(Oil filtration of at least 20 microns is recommended)''
|1 place
|300 hrs / Twice Quarterly
|-
|'''4. Change hydraulic fluid'''
| -
|600 hrs / Quarterly *
|-
|'''5. Complete preventative maintenance (PM)'''
Use form IF-5029 for Vacuum equipped units.

Use form IF-5028 for Magnet equipped units.
| -
|600 hrs / Quarterly
|-
! colspan="3" |NOTES
|-
| colspan="3" |''These recommendations are based on average use in a typical warehouse environment and may be adjusted based on specific circumstances. Dusty and/or extreme hot/cold environments may require more frequent lubrication.''
|-
| colspan="3" |''* BHS recommends implementing an oil sampling and analysis program to monitor hydraulic fluid condition and determine when hydraulic fluid changes are required. The fluid analysis program should be a continuous process and all results should be evaluated. Changes in the condition of the hydraulic system may indicate component wear, fluid deterioration and/or contamination.''
|}
{|
|[[File:NOTICE-warn.png|alt=NOTICE|frameless|120x120px|link=https://tech.bhs1.com/index.php/File:NOTICE-warn.png]]
|
*'''The mounted bearings used on the power rollers, equalization shafts, drive wheels, and drive screw are sealed and shielded bearings. Lubrication may breach the seals of these bearings, therefore these bearings should not be lubricated unless the machine has been cleaned with a high pressure wash on a regular basis (not recommended).'''
*'''Hydraulic fluid should not exceed 140°F (60°C) for extended periods.'''
|}
===<big>'''Reservoir Capacities ''(APPROX.)'''''</big>===
{|
|BE-SL
|18 gal (68 L)
|-
|BE-DS
|18 gal (68 L)
|-
| rowspan="2" |BE-TS
|30 gal (114 L) ''(Units built Pre-2014)''
|-
|45 gal (170 L) ''(Units built 2014 to Present)''
|-
|BE-QS
|60 gal (227 L)
|}The reservoir should be filled so fluid level is within a half inch (1/2") of the top of sight glass. Use Chevron AW 68 or equivalent ISO 68 grade hydraulic oil with anti-wear additives and foam suppressant.

'''''NOTE'':''' Some units shipped from the factory with AW 32 oil for cold environment operation. Units using AW 32 from the factory may experience poor performance if AW 68 is used instead of AW 32 due to the increased viscosity of the oil.

==<big>Preventative Maintenance Reports</big>==
===<big>Vacuum Extraction</big>===
[[File:Battery Extractor Series - Vacuum Extraction Planned Maintenance Inspection Report Page 1.png|alt=Battery Extractor Series - Vacuum Extraction Planned Maintenance Inspection Report Page1|frameless|1238x1238px|link=https://tech.bhs1.com/index.php/File:Battery_Extractor_Series_-_Vacuum_Extraction_Planned_Maintenance_Inspection_Report_Page_1.png]]

[[File:Battery Extractor Series - Vacuum Extraction Planned Maintenance Inspection Report page2.png|alt=Battery Extractor Series - Vacuum Extraction Planned Maintenance Inspection Report Page 2|frameless|1230x1230px|link=https://tech.bhs1.com/index.php/File:Battery_Extractor_Series_-_Vacuum_Extraction_Planned_Maintenance_Inspection_Report_page2.png]]
===<big>Magnet Extraction</big>===
[[File:Battery Extractor Series - Magnet Extraction Planned Maintenance Inspection Report Page 1.png|alt=Battery Extractor Series - Magnet Extraction Planned Maintenance Inspection Report Page 1|frameless|1224x1224px|link=https://tech.bhs1.com/index.php/File:Battery_Extractor_Series_-_Magnet_Extraction_Planned_Maintenance_Inspection_Report_Page_1.png]]

[[File:Battery Extractor Series - Magnet Extraction Planned Maintenance Inspection Report Page 2.png|alt=Battery Extractor Series - Magnet Extraction Planned Maintenance Inspection Report Page 2|frameless|1233x1233px|link=https://tech.bhs1.com/index.php/File:Battery_Extractor_Series_-_Magnet_Extraction_Planned_Maintenance_Inspection_Report_Page_2.png]]

==<big>80292002-i – Equalization Chain Installation / Resetting Procedure</big>==
===<big>Required Tools</big>===
*Large standard screwdriver
*1/8", 5/32", 3/16" Allen wrench
*(2) 1-1/8" Open-end wrenches
*Needle nose pliers
*6" Steel scale (ruler)
*Brake cleaner (non-chlorinated)
*Loctite #242 (blue)
*80292002 - E.Q. Adjustment stop kit (SL, DS, TS) or 80492001 - BE-QS E.Q. Adjustment stop kit
*Ladder or work platform ''(see notes)''
===<big>''Optional Tools''</big>===
*Wire brush for removing Loctite from components prior to reassembly
===<big>Notes</big>===
*''A ladder, man lift or other device is required to access the upper E.Q. studs on BE-TS and BE-QS units.''
*''The following procedures must be performed with the extractor unloaded and in a level area of the travel path.''
*''Installation of the E.Q. stop kit requires (4) persons plus a trained battery extractor operator to raise and lower the inner carriage.''
*''It is recommended to have new E.Q. chain connecting links on hand prior to performing the following procedures.''
*''The upper E.Q. stud lock washers cannot be reused and must be replaced prior to reassembly.''
[[File:IOP-400 BE-SL&DS (10-23) Page 369 Image 0001.png|alt=BE-TS with EQ Adjustment Stops Installed|none|thumb|300x300px|BE-TS with EQ Adjustment Stops Installed|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_Page_369_Image_0001.png]]
===<big>IMPORTANT</big>===
*'''Read and understand the Safety and De-energization Procedure TP-606 before starting this procedure.'''
*'''Read and understand these instructions completely before starting this procedure.'''
===<big>Procedure</big>===
1. Remove the inner and outer frame guards to access the lower equalization studs.

2. Raise the inner frame approximately 30" (762 mm) for SL, DS and TS units or 50" (1270 mm) for QS units from the fully lowered position. Install (1) adjustment stop at each corner of the roller bed. See Figure 1.[[File:IOP-400 BE-SL&DS (10-23) EQ Chain Instructions-Figure1.png|alt=|none|thumb|375x375px|FIGURE 1|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_EQ_Chain_Instructions-Figure1.png]]3. Slowly lower the inner carriage until the roller bed is firmly and securely seated against all four stops. See Figure 2.[[File:IOP-400 BE-SL&DS (10-23) Page 370 Image 0002.png|alt=Roller bed firmly seated against all four stops|none|thumb|398x398px|FIGURE 2|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_Page_370_Image_0002.png]]4. Lockout/tagout the B.E. per your corporate policy.

5. De-energize the B.E. per BHS Safety and De-energization procedure TP-606.

6. Loosen and remove the upper hex nuts and remove the upper chain studs. Remove the lock washers from the upper chain studs. Save the hex nuts for reassembly later. Discard the lock washers and obtain new, 3/4" split-ring lock washers for reassembly.

7. If replacing the chain, remove the upper stud and remove the chain from the lower stud. Discard the connecting links.
*''If the E.Q. chains are being reset due to a connecting link failure, it is recommended to also replace the stud where the connecting link failed.''
*''It is recommended to replace the connecting links when replacing or resetting the E.Q. chains.''
8. If replacing a lower stud, remove the connecting link and disconnect the chain. Loosen the hex nut and remove the stud. Remove the hex nut from the old stud and reinstall it on the new stud. Reinstall the new stud so that it is flush with the bottom of the frame and the hole is aligned front-to-back with the extractor.

9. Attach the chains to the lower studs using the connecting links. Attach the upper studs to the chains using the connecting links, making sure the nut is threaded down near the connecting link and lay the chains in the frame. See Figure 3.
*''Do not fully assemble the lower connecting links by bending the cotter pins as the connecting link may need to be removed later for stud adjustment.''[[File:IOP-400 BE-SL&DS (10-23) EQ Chain Attached to Upper Stud.png|alt=BE-TS Chain Attached to Upper Stud|none|thumb|300x300px|FIGURE 3|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_EQ_Chain_Attached_to_Upper_Stud.png]]
10. If new E.Q. sprockets are to be installed, remove the clamp collars and old sprockets. Install the new sprockets and reinstall the clamp collars. DO NOT tighten the set screws at this point as adjustment/alignment may be required.
*''Sprockets MUST be keyed in-line.''
11. Align the E.Q. shafts so that the keyways are in the 2 o'clock position (approximately 60 degrees from vertical). This will bring the sprocket set screws to the top of the sprocket when the inner carriage is lowered. See Figure 4.[[File:IOP-400 BE-SL&DS (10-23) EQ Shafts aligned 60 Degrees from Vertical.png|alt=BE-TS EQ Shafts aligned 60 Degrees from Vertical|none|thumb|300x300px|FIGURE 4|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_EQ_Shafts_aligned_60_Degrees_from_Vertical.png]]12. Starting with the inside chain, route the chain over the sprocket directly above the lower stud and under the inside sprocket on the opposite shaft. Attach the upper stud to the top cross bar, making sure a new 3/4" split -ring lock washer is installed between the cross bar and lower hex nut. Hand tighten the upper stud adjusting nut to remove slack from the chain. See Figure 5.

13. Route the outer chain over the sprocket, above the stud and under the sprocket on the opposite shaft. Attach the upper stud to the top cross bar, making sure a new, 3/4" split-ring lock washer is installed between the cross bar and lower hex nut. Hand tighten the upper stud adjusting nut to remove slack from the chain. See Figure 5.
*''It is recommended to begin at the operator end where room is limited allowing easier access at the opposite end to route the chain under the final sprocket.''
[[File:IOP-400 BE-SL&DS (10-23) Inside and Outside EQ Chains.png|alt=BE-TS Inside and Outside EQ Chains|none|thumb|499x499px|FIGURE 5|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_Inside_and_Outside_EQ_Chains.png]]14. Repeat steps 11 through 13 for the opposite side of the extractor. It is likely that a large, standard screwdriver will be necessary to position the final chain over the sprocket. See Figure 6.[[File:IOP-400 BE-SL&DS (10-23) Page 371 Image 0002.png|alt=It is likely that a large, standard screwdriver will be necessary to position the final chain over the sprocket.|none|thumb|300x300px|FIGURE 6|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_Page_371_Image_0002.png]]15. Adjust the lower studs up or down as necessary to take the slack out of the chain between the lower studs and the sprockets by removing the connecting link from the stud and turning the stud. Tighten the hex nuts against the frame once the studs have been adjusted. Reattach the chain.
*DO NOT allow the stud to twist when tightening the hex nuts.
16. Tighten the upper hex nut on the upper studs until there is approximately 1/4" (7 mm) of total deflection in the middle of the upper, vertical chain sections. Tighten the lower hex nuts on the upper studs to lock the studs in place.
*''Each section of chain between the sprockets should have approximately the same tension as the other on the same side. See Figure 5.''
17. Raise the inner frame and remove the adjustment stops from the four corners and lower the inside frame.

18. Verify equalization sprocket and stud alignment by using a 6" scale. Measure the distance from the inside roller bed frame to the center of the equalization stud. Compare this distance with the measurements from the inside roller bed frame to the center-lines of the sprockets. Adjust the position of the sprocket as necessary to make the distances equal. This will ensure the chain and sprockets are in line with the stud. Repeat this process for the three remaining chains. See Figures 7 & 8.

19. Raise and lower the inner frame several times and listen for any chain popping noises to confirm the sprockets are in line with the lower studs. If there is no popping noise, lower the inner frame all the way down.[[File:IOP-400 BE-SL&DS (10-23) EQ Chain Verify equalization sprocket and stud alignment by using a 6in scale-Fig7.png|alt=BE-TS EQ Chain Procedure Figure 7 - Verify equalization sprocket and stud alignment by using a 6" scale|none|thumb|300x300px|FIGURE 7|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_EQ_Chain_Verify_equalization_sprocket_and_stud_alignment_by_using_a_6in_scale-Fig7.png]][[File:IOP-400 BE-SL&DS (10-23) EQ Chain Verify equalization sprocket and stud alignment by using a 6in scale-Fig8.png|alt=BE-TS EQ Chain Verify equalization sprocket and stud alignment by using a 6in scale - Fig 8|none|thumb|300x300px|FIGURE 8|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_EQ_Chain_Verify_equalization_sprocket_and_stud_alignment_by_using_a_6in_scale-Fig8.png]]20. Clean any existing, hardened Loctite from the sprockets, sprocket sets screws, clamp collars and clamp collar bolts.

21. Apply Loctite to and tighten the set screws on the sprockets. Slide the clamp collars against the outside sprocket, loctite and tighten the clamp collars.
==<big>80292001-i – Battery Extractor Service Stand Installation Instructions</big>==
===<big>Required Tools</big>===
None
===<big>Notes</big>===
*''Refer to kit part # 80292001 or 80392001 for the complete bill of materials supplied.''
*''Remove ALL batteries from extractor prior to installation / service.''
*''Installation of service stands requires (2) persons plus a trained battery extractor operator to raise and lower the inner carriage. DO NOT attempt installation with less than (3) persons.''
[[File:IOP-400 BE-SL&DS (10-23) Single Level Service Stand Properly Installed.png|alt=Single Level Service Stand Properly Installed|none|thumb|368x368px|Single Level Service Stand Properly Installed|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_Single_Level_Service_Stand_Properly_Installed.png]]
===<big>IMPORTANT</big>===
*'''Read and understand the Safety and De-energization Procedure TP-606 before starting this procedure.'''
*'''Read and understand these instructions completely before starting this procedure.'''
===<big>Procedure</big>===
1. Have a qualified operator raise the inner carriage of the extractor to the required height for installation. For single level applications, the required height will be approximately 25" (64 cm) from the fully lowered position. For double, triple, and quad stack machines, the required height will be approximately 55" (140 cm) from the fully lowered position.
*On double, triple, and quad stack battery extractors, the operator either must remain on the operator platform during service or be provided an OSHA approved method of egress. This is not applicable to single level battery extractors as the operator platform height is fixed.
2. Install the stands by engaging the top of the stand into the inner carriage cutouts. Place the bottom channel of the stand over the tube of the outer frame. The top flanges of each stand are tapered to aid in proper alignment of the stand with the inner frame.

See Figures 1 & 2.[[File:IOP-400 BE-SL&DS (10-23) engaging the top of the stand into the inner carriage cutout.png|alt=Properly seated in cutout|none|thumb|300x300px|FIGURE 1|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_engaging_the_top_of_the_stand_into_the_inner_carriage_cutout.png]][[File:IOP-400 BE-SL&DS (10-23) Page 374 Image 0005.png|none|thumb|300x300px|FIGURE 2|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_Page_374_Image_0005.png]]3. Once BOTH stands have been properly placed, SLOWLY lower the inner carriage while the stands are held in place.

4. Once the inner carriage is firmly seated on the service stands, verify the stands are securely installed. See Figure 3.[[File:IOP-400 BE-SL&DS (10-23) Page 374 Image 0006.png|none|thumb|450x450px|FIGURE 3|link=https://tech.bhs1.com/index.php/File:IOP-400_BE-SL&DS_(10-23)_Page_374_Image_0006.png]]
==<big>Trouble Shooting Guide</big>==
{| class="wikitable"
!Problem Symptom
!Probable Cause
!Solution
|-
|Hydraulic power Unit does not operate.
No electric to power unit motor.
|1. No AC power to Unit.
2. Reset on magnetic motor starter tripped.

3. Gate switch not actuated.

4. Foot Pedal switch not engaged.

5. Emergency Stop switch is depressed.
|1. Check fuses or breaker.
2. Check reset button.

3. Make sure safety gate is engaging switch.

4. Check foot pedal for obstruction.

5. Reset button using machine key.
|-
|Power unit runs but no pressure reading at gauge,
also no functions move.
|1. AC input is in reverse phase. Motor is running backwards.
2. Main system relief valve stuck open or defective.

3. Coupling between motor and pump loose.
|1. Reverse any two of the three hot lines to unit.
2. Check relief valve cartridge for trash or debris.

Replace as required.

3. Inspect coupling assy.
|-
|Magnetic starter contact chatters-at startup.
Contact chatters while traveling.
|1. 1 leg of 3 phase input power out.
2. Safety gate and/or gate switch out of adjustment.
|1. Check fuse or circuit breaker at service panel.
2. Check and adjust gate or switch as required to

ensure full engagement of plunger on gate

switch and that the safety gate is not bouncing

due to vibration.
|-
|No floor travel empty or loaded-all other functions work properly.
|1. Extractor arm off center-left to right.
2. Proximity switch or sensing bracket out of target range.

3. Proximity switch defective or broken.

4. Bad solenoid coil on floor cutout valve.

5. Spool on floor cutout valve stuck open.
|1. Center arm.
2. Adjust as needed to achieve 1/4” clearance.

3. Check switch and replace.

4. Check solenoid and replace if needed.

5. Remove and clean spool cartridge or replace.
|-
|Floor travel moves but is sluggish
and stalls with a load at certain points.
|1. Uneven floor conditions. High/low spots.
2. Excessive tire wear.

3. Wheel shaft-to-motor shaft coupling on drive wheel assembly loose or broken.

4. Debris lodged under battery extractor.
|1. Check flatness of floor. Check guidance track for scraping of guide arm on top of angle.
2. Measure under clearance of battery extractor. Should be no less than 5/8” replace poly wheels as needed.

3. Inspect drive assembly while under load to see if shafts and couplings are moving in unison. Repair as needed.

4. Inspect under unit and remove debris.
|-
|Inner carriage bounces while lifting under load,
but not when empty.
|1. Down speed adjustment valve open too far.
|1. Adjust as needed to eliminate carriage bounce.
|-
|Inner carriage does not lift evenly.
Four corners do not land evenly against outer frame tube.
|1. Equalization chains are out of adjustment.
2. Excessive chain or sprocket wear.

3. Equalization chains are out of synchronization. Possibly may have jumped a sprocket tooth.

4. Broken bearing housing on mounted shaft.

5. Lift cylinder roping chains out of adjustment.
|1. Readjust with the top stud until equal tension is achieved.
2. Replace as needed.

3. Evaluate and resynchronize as required.

4. Inspect and replace.

5. Readjust as needed to equal tension on all four cylinders in full down position.
|}
=<big>Aftermarket Support</big>=
[https://na.bhs1.com/blog/post/tt-922-technical-support Click here] for details on BHS' Aftermarket Support.
=<big>Statement of Warranty</big>=
[https://store.bhs1.com/warranty Click here] for details on BHS' Statement of Warranty.

IOP-265 Graybar SRD

2026-01-27T12:32:44Z

Mbowen: Mbowen moved page IOP-265 Graybar SRD to IOP-265 (SRD)

#REDIRECT [[IOP-265 (SRD)]]

IOP-265 (SRD)

2026-01-27T12:32:44Z

Mbowen: Mbowen moved page IOP-265 Graybar SRD to IOP-265 (SRD)

{{DISPLAYTITLE:IOP-265 SRD}}

== GENERAL INFORMATION ==
Read & understand this manual before installation, use, and maintenance for your desk. If you have any questions regarding operation, service, or the contents of this manual, please contact your dealer or BHS Technical Support '''1.877.BHS.4YOU (1.877.247.4968).'''

he BHS SRD (Shipping/Receiving Desk) is a fully adjustable packing desk. Heavy duty formed steel frame and formed steel shelves provide a rigid, high capactiy desk. Each unit contains (1) fixed lower shelf (500 lb capacity), (1) fixed platform top (500 lb capacity) and (2) adjustable shelves (350 lb capacity each). Platform top cut outs are available in left, right, and ambidextrous to accommodate operator’s handing; a flush platform top is also available. All cutouts and formed edges are outlined in heavy duty vinyl edging to eliminate sharp edges and corners. Included is a drop in scale tray with a cord grommet. Detachable monitor mount and key board tray can be mounted on either left or right hand side with multiple vertical adjustment points. Arms feature two lateral pivot points and tilt function to ergonomically position a screen and keyboard (34” full extension). Formed steel shelves are vertically adjustable in 3” increments, as well as horizontally in 2” increments. Please consult a dealer or sales representative for application specific needs.

=== MODEL NUMBER & OPTIONS ===
[[File:IOP-265-1.JPG|500px]]

'''Available Platform Handing'''

LH - Left Hand Cutout 2

RH - Right Hand Cutout

FH - Flush Top, No Cutout

AMB - Ambidextrous Cutouts; Left and Right Hand

'''Available Platform Finish'''

PC - Powder Coat Platform Top

SST - Stainless Steel Platform Top 2

'''Standard Features'''

SRD-KEYBOARD = Detachable, Adjustable Keyboard Tray 2

SRD-MONITOR = Detachable, Adjustable Monitor Mount 2

SRD-LIGHT = Installed 48” Light Fixture, 120V ac 2

'''Additional Options'''

SRD-LOGO = Custom Lasered Logo 1

SRD-SUPPLY = Detachable Office Supply Caddy

SRD-SCAN = Detachable Scanner Gun Caddy

SRD-PAPER = Detachable Craft Paper Roll Bar

SRD-LABEL = Detachable Adjustable Label Roll Bar

SRD-POWER = Installed Power Module

SRD-NS = Non-Standard Option1

1 Consult factory for units with NS options as components may be completely unique to the particular unit. 2 Standard, unless otherwise specified.

=== PRODUCT SPECIFICATIONS===
[[File:IOP-265 SRD B1.jpg|500px|border]]

==FRAME==

==== VERTICAL FRAME====
[[File:IOP-265 SRD 1.0.1.jpg|500px|border]]

[[File:IOP-265 SRD 1.0.2.jpg|500px|border]]

[[File:IOP-265 SRD 1.0.3.jpg|500px|border]]

[[File:IOP-265 SRD 1.0.4.jpg|500px|border]]

==== BASE FRAME====
[[File:IOP-265 SRD 1.1.1.jpg|500px|border]]

[[File:IOP-265 SRD 1.1.2.jpg|500px|border]]

[[File:IOP-265 SRD 1.1.3.jpg|500px|border]]

[[File:IOP-265 SRD 1.1.4.jpg|500px|border]]

==PLATFORM TOP==

==== LEFT HAND / RIGHT HAND ====
[[File:IOP-265 SRD 2.0.1.jpg|500px|border]]

[[File:IOP-265 SRD 2.0.2.jpg|500px|border]]

[[File:IOP-265 SRD2.0.3 .jpg|500px|border]]

==== FLUSH====
[[File:IOP-265 SRD 2.1.1.jpg|500px|border]]

==== AMBIDEXTROUS====
[[File:IOP-265 SRD 2.2.1.jpg|500px|border]]

[[File:IOP-265 SRD 2.2.2.jpg|500px|border]]

[[File:IOP-265 SRD 2.2.3.jpg|500px|border]]

==== INSTALLATION AND ASSEMBLY====
[[File:IOP-265 SRD 2.3.1.jpg|500px|border]]

[[File:IOP-265 SRD 2.3.2.jpg|500px|border]]

[[File:IOP-265 SRD 2.3.3.jpg|500px|border]]

[[File:IOP-265 SRD 2.3.4.jpg|500px|border]]

== SHELVES==

=== LOWER SHELF===
[[File:IOP-265 SRD 3.0.1.jpg|500px|border]]

[[File:IOP-265 SRD 3.0.2.jpg|500px|border]]

[[File:IOP-265 SRD 3.0.3.jpg|500px|border]]

=== UPPER SHELVES ===
[[File:IOP-265 SRD 3.1.1.jpg|500px|border]]

[[File:IOP-265 SRD 3.1.2.jpg|500px|border]]

[[File:IOP-265 SRD 3.1.3.jpg|500px|border]]

[[File:IOP-265 SRD 3.1.4.jpg|500px|border]]

== MOUNTING ARMS ==

=== KEYBOARD TRAY ===
[[File:IOP-265 SRD 4.0.1.jpg|500px|border]]

=== MONITOR MOUNT ===
[[File:IOP-265 SRD 4.1.1.jpg|500px|border]]

== STANDARD AVAILABLE OPTIONS ==

=== SRD-SUPPLY ===
[[File:IOP-265 SRD 5.0.1.jpg|500px|border]]

=== SRD-SCAN ===
[[File:IOP-265 SRD 5.1.1.jpg|500px|border]]

=== SRD-PAPER ===
[[File:IOP-265 SRD 5.2.1.jpg|500px|border]]

=== SRD-LABEL ===
[[File:IOP-265 SRD 5.3.1.jpg|500px|border]]

=== SRD-POWER ===
[[File:IOP-265 SRD 5.4.1.jpg|500px|border]]

==STATEMENT OF WARRANTY==

'''Statement of Warranty'''

Battery Handling Systems, Inc. and its subsidiaries and affiliates (collectively “BHS”) warrants to the original purchaser of its equipment, that the equipment shall be free from defects in material and workmanship under normal and proper use, operation, and maintenance during the applicable warranty period set forth below for the product containing the alleged defect:

<ul>
<li>Thirteen (13) months from the date of shipment to the original purchaser with respect to frames, weldments, electric drives, motors (except brushes), motor driven pumps, valves, and drive wheel assemblies (except wheels) only.</li>

<li>Ninety (90) days from the date of shipment to the original purchaser with respect to all other parts not covered above.</li>

<li>Bulbs, fuses, and filters are not included in this ninety (90) day warranty, unless found to be defective prior to use or within (90) days of shipment to the original purchaser, whichever occurs first. 

BHS’s warranty obligations hereunder are contingent upon the following conditions: (1) BHS or its authorized dealer is promptly (but in no event later than thirty (30) days following the discovery of the claimed defect) notified of the defect; (2) the purchaser establishes to BHS’s reasonable satisfaction that any goods have been properly installed, maintained, and operated; (3) the purchaser returns the defective goods or any part thereof to BHS; and (4) the purchaser complies with all other warranty procedures required by BHS (such procedures are available upon request). Upon a determination by BHS that a product is defective within the above-mentioned warranty period(s), BHS may, at its exclusive option, either provide parts and labor to repair or replace said defective equipment, or grant a credit or refund of the purchase price of the defective equipment. Repaired or replacement equipment and parts will carry the foregoing warranty for the remainder of the original warranty period or ninety (90) days from the date of shipment of the repaired/replaced equipment, whichever is longer.</li>
</ul>

BHS will cover normal ground freight charges such as ground UPS, common carrier, etc. for the delivery of repaired or replaced equipment or parts covered by this warranty. The cost of any express delivery, if requested, will be the sole responsibility of the purchaser, and the purchaser agrees to provide its account number with its preferred carrier to BHS or to pay the entire cost of express delivery as a condition of BHS’s provision of such express delivery. Unless expressly authorized in writing by BHS, the foregoing warranty does not cover the cost of removal or reinstallation of equipment (or the cost of other activities ancillary thereto), the cost of which will be borne solely by the purchaser.

This warranty is void in the case of abuse, misuse, abnormal use, accidents, overloading, improper installation, repair, or maintenance (other than by BHS), modification of products, application of products not in accordance with the instruction manual and product application bulletins, or any other reason BHS determines that said product is not operating properly as a result of causes other than defective manufacture.

This warranty shall apply exclusively to products sold to the purchaser by BHS. BHS shall not have any liability or obligation to the purchaser, under this warranty or other- wise, with respect to any defect or failure of performance in products which are not sold or manufactured by BHS, including any such products which are commingled with or incorporated into any BHS products, or any products into which BHS products are incorporated as a system component or otherwise without the prior written approval of BHS. This warranty does not cover accessories and attachments not manufactured by BHS. The original manufacturer’s warranty, if any, for such accessories or attachments takes precedence and all claims shall be directed to their respective manufacturers.

ANY LITIGATION TO ENFORCE THE FOREGOING WARRANTY MUST BE COMMENCED NO LATER THAN ONE (1) YEAR AFTER DISCOVERY REASONABLY SHOULD HAVE BEEN MADE OF ANY FACTS OR OTHER INFORMATION SUGGESTING THE EXISTENCE OF A PRODUCT FAILURE OR A PRODUCT DEFECT. THE WARRANTY SET FORTH HEREIN IS THE COMPLETE AND ENTIRE WARRANTY MADE BY BHS AND ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MER- CHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, NON-INFRINGEMENT, OR OTHERWISE, ARE HEREBY EXPRESSLY EXCLUDED. NO PERSON IS AUTHORIZED TO MAKE ANY OTHER OR ADDITIONAL WARRANTY ON BEHALF OF BHS. THE RIGHT TO REPAIR, REPLACEMENT, OR CREDIT/REFUND, AS SET FORTH HEREIN, IS THE SOLE AND EXCLUSIVE REMEDY FOR BREACH OF THE ABOVE WARRANTY. BHS SHALL NOT BE LIABLE FOR CHARGES OR EXPENSES OF ANY NATURE UNDER THE FOREGOING WARRANTY INCURRED WITHOUT BHS’S CONSENT. FURTHER, UNDER NO CIRCUMSTANCES, REGARDLESS OF THE FORM OF THE CLAIM OR CAUSE OF ACTION (WHETHER IN WARRANTY, CONTRACT, INFRINGEMENT, NEGLIGENCE, STRICT LIABILITY, OR FOR ANY OTHER TORT OR CLAIM), SHALL BHS BE LIABLE TO THE PURCHASER OR ANYONE ELSE FOR ANY: (A) INCIDENTAL DAMAGES (EXCEPT AS SPECIFICALLY PROVIDED FOR ABOVE), OR CONSEQUENTIAL, INDIRECT, SPECIAL OR PUNITIVE DAMAGES RELATIVE TO OR ARISING FROM OR CAUSED DIRECTLY OR INDIRECTLY BY SAID PRODUCTS OR THE USE THEREOF OR ANY DEFICIENCY, DEFECT, OR INADEQUACY OF SAID PRODUCTS; OR (B) DIRECT DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE BHS EQUIPMENT GIVING RISE TO THE CLAIM OR CAUSE OF ACTION, OR AT THE ELECTION OF BHS, THE RESTORATION OR REPLACEMENT OR REPAIR OF SUCH EQUIPMENT. “CONSEQUENTIAL DAMAGES” INCLUDE, WITHOUT LIMITATION, LOST PROFITS, BUSINESS INTERRUPTION DAMAGES, LOSS OF USE DAMAGES, AND DAMAGE TO REPUTATION OR GOODWILL.
This Warranty is governed by and construed in accordance with the laws of the State of Missouri, without regard to conflict of law principles. All disputes or controversies arising out of or in connection with this Warranty shall be subject to the exclusive jurisdiction of the U.S. District Court for the Eastern District of the State of Missouri and any and all process in connection with any litigation arising out of such dispute or controversy may be served by registered, certified mail, return receipt requested, outside Missouri, with the same force and effect as if service had been made in Missouri.

If part of this Warranty is held to be invalid or unenforceable, such invalidity or unenforceability shall not invalidate or render unenforceable the entire Warranty, but rather the Warranty shall be construed as if not containing the particular invalid or unenforceable provision.

== WARRANTY PROCEDURES ==
'''Warranty Procedures'''

Please refer to '''Battery Handling Systems, Inc.'s''' Statement of Warranty and Liability (which is set forth on the reverse side hereof or available upon request) for a complete description of '''BHS'''' warranty. In the event of conflict between '''BHS'''' warranty and these procedures, the warranty will control.

'''Battery Handling Systems, Inc.'s''' warranty policy is intended to protect original purchasers who submit valid claims, as well as to identify and eliminate claims where product failure is the result of customer abuse, neglect or misapplication.

'''Step 1: Gather Information'''

The following information must be provided immediately.

<ul>
<li>A description of the product that includes, at a minimum, the model, serial number, and hour meter reading (if applicable).</li>
<li>Customer name, location, and contact information including phone number.</li>
<li>Installation date, installation provider (dealer), servicing dealer, and selling dealer.</li>
<li>Any prior repairs, modification, or adjustments.</li>
</ul>

'''Step 2: Contact BHS'''

Contact '''BHS''' at:

Phone: 1.877.247.4968 
Fax: 1.314.423.5948 
Email: service@bhs1.com

'''Step 3: Authorization'''

BHS will authorize further evaluation, repair, or replacement. A warranty claim form indicating '''BHS''' prior authorization for any such action will be issued to claimant. The completed warranty claim form must be submitted with any request for warranty credit.

'''Step 4: Request RGA Number'''

<ul>
<li>Suspected defective parts must be returned to '''BHS''' under an issued Return Goods Authorization (RGA) number.</li>
<li>BHS will specify the proper disposition of the parts through the issue of an RGA number.</li>
<li>Return shipment method will also be specified at time of RGA issue. RGAs are good for thirty (30) days from date issued; no credit will be issued for items returned after the RGA has expired.</li>
</ul>

'''Step 5: Claim Warranty'''

<ul>
<li>Submit Warranty Claim forms and supporting documents to: Battery Handling Systems, Inc. 
P.O. Box 28990 
St. Louis, MO 63132 
Fax: 1.314.423.5948 
Email: service@bhs1.com</li>
<li>Labor allowance hours are determined by our engineering staff.</li>
<li>Actual travel time, labor time, and parts costs must be indicated as separate items as provided on the form.</li>
</ul>

'''Step 6: BHS will process warranty claim and notify purchaser of final disposition.'''

{{DEFAULTSORT:IOP-265_SRD}}

IOP-265 (SRD)

2026-01-27T12:20:43Z

Mbowen:

IOP-265 (SRD)

2026-01-27T12:19:40Z

Mbowen:

IOP-400 Single Level and Double Stack Operator Aboard Battery Extractors (BE-SL&DS)

2026-01-27T12:19:25Z

Mbowen:

'''Looking for a specific replacement part?''' Ctrl-F (or Command-F for Mac users) brings up your browsers search panel and can search any text on the entire web page. Find parts by searching a part # or part description.

'''California Residents''': WARNING: This product contains chemicals known to the State of California to cause cancer and/or reproductive harm, and birth defects or other reproductive harm. [https://na.bhs1.com/about-bhs/compliance-statement-for-california-proposition-65/ Learn more here.]

[[File:Updated Manual Notice.png|alt=UPDATED|frameless|link=https://tech.bhs1.com/index.php/File:Updated_Manual_Notice.png]]

= Preface =
THIS MANUAL IS TO BE USED TO SERVICE '''SINGLE LEVEL (SL)''' AS WELL AS '''DOUBLE STACK (DS)''' BATTERY EXTRACTORS.

ANY VIEWS NOT SPECIFICALLY STATED OTHERWISE ARE OF THE SINGLE LEVEL EXTRACTOR. THE PARTS LISTED ARE COMMON FOR SINGLE LEVEL AND DOUBLE STACK UNLESS OTHERWISE NOTED IN THE NOTES COLUMN OF THE PARTS.
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="2" |1
|00158001-10
|CHAIN-ROLLER-#60
|
|BE-SL ONLY
|4
|-
|00158001-12
|CHAIN-ROLLER-#60
|
|BE-DS ONLY
|4
|}
FOR ITEMS OR ASSEMBLIES THAT ARE UNIQUE TO ONLY THE '''SL''' OR '''DS''', IT WILL BE DESIGNATED AS SUCH ON THE DIAGRAMAND HAVE A SEPARATE, CORRESPONDING PARTS LIST FOR THAT DIAGRAM.

WHEN SERVICING '''HIGH PERFORMANCE (BE-DS-HP)''' MODELS, REFER TO SECTION 6.2 FOR ALL PARTS UNIQUE TO HIGH PERFORMANCE UNITS. IF A PARTICULAR PART IS NOT FOUND IN SECTION 6.2, REFER TO THE STANDARD PARTS SECTION(S) OF THIS MANUAL.

= TP-606 Safety & De-Energization Procedures =

== Operational Safety ==
{|
|[[File:Read Before Operating Notice.png|alt=Read Before Operating|frameless|150x150px]]
|
* Read and understand all instructions and warnings before using or servicing this equipment.
* Keep these instructions for future reference.
|}

* Battery Extractor (BE) units shall only be operated by suitable persons of at least 18 years of age, who have been trained in the proper and safe operation of the BE and expressly certified/charged, in writing, by the user or their representative.
* Only one person is permitted to travel on the BE at any time.
* BE units shall only be used indoors in an industrial setting on a hard, nonslip, and level floor without defects including but not limited to holes, gouges, cracks, drains or obstacles comprised of concrete or other suitable industrial material meeting the minimum requirements specified by BHS as well as any local requirements.
* A licensed structural engineer should be consulted prior to installing a BE on any building level other than the ground floor.
* BE units are not designed to be shipped or transported after initial delivery.
* Failure to follow these instructions and warnings may result in property damage, personal injury or death.

=== WORK AREA ===

* Keep work area clean and well lit. Cluttered work areas and poor lighting can lead to accidents.
* Clean up/contain any fluid spills immediately to pre-vent slips or falls.
* Be aware of potential hazards when performing any service or maintenance to the unit.

=== SERVICE & MAINTENANCE ===
Service personnel shall wear Personal Protective Equipment (PPE) appropriate for the task being performed.
{|
|[[File:Electrical Hazard Warning.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Electrical_Hazard_Warning.png]]
[[File:Danger Warning.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Danger_Warning.png|alt=DANGER]]
|
=== LOCKOUT/TAGOUT ===
'''Lockout/tagout the BE per your corporate policy, if damaged or not functioning properly. Lockout/tagout and de-energize all systems prior to per-forming any maintenance or service to unit.'''
|}
{|
|[[File:Warning-Battery-Explosion.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Warning-Battery-Explosion.png]]
[[File:Danger Warning.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Danger_Warning.png|alt=DANGER]]
|
=== LEAD-ACID BATTERY EXPLOSION HAZARD ===
'''DO NOT allow open flames or sparks of any kind near a battery. Highly explosive gas is generated when charging a battery that can remain in battery cells for extended periods of time after charging is complete.'''

* Always wear appropriate PPE including rubber apron, gloves, boots and full face shield when performing service or maintenance to any lead-acid batteries.
* DO NOT place metal or other conductive objects on top of battery. Arcing may occur causing damage to the battery and/or serious personal injury or death.
* Use only chargers matching the voltage and amperage of the battery being charged. Overcharging a battery can cause damage to the battery, charger and/or serious personal injury or death.
* Turn off charger before disconnecting battery from charger. Arcing between battery and charger connec-tors can cause damage to the connectors and/or serious personal injury or death.
|}
{|
|[[File:Warning-Hydrualic-Hazard.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Warning-Hydrualic-Hazard.png]]
[[File:Warning.png|alt=WARNING|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Warning.png]]
|
=== HYDRAULIC HAZARDS ===
'''AVOID HIGH PRESSURE FLUIDS-Escaping fluid under pressure can penetrate the skin causing serious injury. Relieve pressure before discon-necting hydraulic lines. Tighten all connections before applying pressure. Keep hands and body away from pin holes which eject fluids under high pressure. Use a piece of cardboard or paper to search for leaks. DO NOT use your hand.Any fl uid injected into the skin under high pres-sure should be considered a serious medical emergency despite an initial normal appearance of the skin. There will be a delayed onset of pain, and serious tissue damage may occur. Medical attention should be sought immediately.'''
|}
{|
![[File:No Pacemakers Notice.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:No_Pacemakers_Notice.png]][[File:Strong Magnet Field Hazard Warning.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Strong_Magnet_Field_Hazard_Warning.png]]
[[File:Warning.png|alt=WARNING|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Warning.png]]
|
===ELECTROMAGNET HAZARD===
'''Units equipped with magnetic extraction generate strong magnetic fields. Persons with pacemakers SHOULD''' '''NOT''' '''operate or be in close proximity to equipment during operation. Failure to comply with this direction''' '''could result in serious personal injury or death.'''
|}

IOP-265 (SRD)

2026-01-27T12:16:52Z

Mbowen:

== GENERAL INFORMATION ==
Read & understand this manual before installation, use, and maintenance for your desk. If you have any questions regarding operation, service, or the contents of this manual, please contact your dealer or BHS Technical Support '''1.877.BHS.4YOU (1.877.247.4968).'''

he BHS SRD (Shipping/Receiving Desk) is a fully adjustable packing desk. Heavy duty formed steel frame and formed steel shelves provide a rigid, high capactiy desk. Each unit contains (1) fixed lower shelf (500 lb capacity), (1) fixed platform top (500 lb capacity) and (2) adjustable shelves (350 lb capacity each). Platform top cut outs are available in left, right, and ambidextrous to accommodate operator’s handing; a flush platform top is also available. All cutouts and formed edges are outlined in heavy duty vinyl edging to eliminate sharp edges and corners. Included is a drop in scale tray with a cord grommet. Detachable monitor mount and key board tray can be mounted on either left or right hand side with multiple vertical adjustment points. Arms feature two lateral pivot points and tilt function to ergonomically position a screen and keyboard (34” full extension). Formed steel shelves are vertically adjustable in 3” increments, as well as horizontally in 2” increments. Please consult a dealer or sales representative for application specific needs.

=== MODEL NUMBER & OPTIONS ===
[[File:IOP-265-1.JPG|500px]]

'''Available Platform Handing'''

LH - Left Hand Cutout 2

RH - Right Hand Cutout

FH - Flush Top, No Cutout

AMB - Ambidextrous Cutouts; Left and Right Hand

'''Available Platform Finish'''

PC - Powder Coat Platform Top

SST - Stainless Steel Platform Top 2

'''Standard Features'''

SRD-KEYBOARD = Detachable, Adjustable Keyboard Tray 2

SRD-MONITOR = Detachable, Adjustable Monitor Mount 2

SRD-LIGHT = Installed 48” Light Fixture, 120V ac 2

'''Additional Options'''

SRD-LOGO = Custom Lasered Logo 1

SRD-SUPPLY = Detachable Office Supply Caddy

SRD-SCAN = Detachable Scanner Gun Caddy

SRD-PAPER = Detachable Craft Paper Roll Bar

SRD-LABEL = Detachable Adjustable Label Roll Bar

SRD-POWER = Installed Power Module

SRD-NS = Non-Standard Option1

1 Consult factory for units with NS options as components may be completely unique to the particular unit. 2 Standard, unless otherwise specified.

=== PRODUCT SPECIFICATIONS===
[[File:IOP-265 SRD B1.jpg|500px|border]]

==FRAME==

==== VERTICAL FRAME====
[[File:IOP-265 SRD 1.0.1.jpg|500px|border]]

[[File:IOP-265 SRD 1.0.2.jpg|500px|border]]

[[File:IOP-265 SRD 1.0.3.jpg|500px|border]]

[[File:IOP-265 SRD 1.0.4.jpg|500px|border]]

==== BASE FRAME====
[[File:IOP-265 SRD 1.1.1.jpg|500px|border]]

[[File:IOP-265 SRD 1.1.2.jpg|500px|border]]

[[File:IOP-265 SRD 1.1.3.jpg|500px|border]]

[[File:IOP-265 SRD 1.1.4.jpg|500px|border]]

==PLATFORM TOP==

==== LEFT HAND / RIGHT HAND ====
[[File:IOP-265 SRD 2.0.1.jpg|500px|border]]

[[File:IOP-265 SRD 2.0.2.jpg|500px|border]]

[[File:IOP-265 SRD2.0.3 .jpg|500px|border]]

==== FLUSH====
[[File:IOP-265 SRD 2.1.1.jpg|500px|border]]

==== AMBIDEXTROUS====
[[File:IOP-265 SRD 2.2.1.jpg|500px|border]]

[[File:IOP-265 SRD 2.2.2.jpg|500px|border]]

[[File:IOP-265 SRD 2.2.3.jpg|500px|border]]

==== INSTALLATION AND ASSEMBLY====
[[File:IOP-265 SRD 2.3.1.jpg|500px|border]]

[[File:IOP-265 SRD 2.3.2.jpg|500px|border]]

[[File:IOP-265 SRD 2.3.3.jpg|500px|border]]

[[File:IOP-265 SRD 2.3.4.jpg|500px|border]]

== SHELVES==

=== LOWER SHELF===
[[File:IOP-265 SRD 3.0.1.jpg|500px|border]]

[[File:IOP-265 SRD 3.0.2.jpg|500px|border]]

[[File:IOP-265 SRD 3.0.3.jpg|500px|border]]

=== UPPER SHELVES ===
[[File:IOP-265 SRD 3.1.1.jpg|500px|border]]

[[File:IOP-265 SRD 3.1.2.jpg|500px|border]]

[[File:IOP-265 SRD 3.1.3.jpg|500px|border]]

[[File:IOP-265 SRD 3.1.4.jpg|500px|border]]

== MOUNTING ARMS ==

=== KEYBOARD TRAY ===
[[File:IOP-265 SRD 4.0.1.jpg|500px|border]]

=== MONITOR MOUNT ===
[[File:IOP-265 SRD 4.1.1.jpg|500px|border]]

== STANDARD AVAILABLE OPTIONS ==

=== SRD-SUPPLY ===
[[File:IOP-265 SRD 5.0.1.jpg|500px|border]]

=== SRD-SCAN ===
[[File:IOP-265 SRD 5.1.1.jpg|500px|border]]

=== SRD-PAPER ===
[[File:IOP-265 SRD 5.2.1.jpg|500px|border]]

=== SRD-LABEL ===
[[File:IOP-265 SRD 5.3.1.jpg|500px|border]]

=== SRD-POWER ===
[[File:IOP-265 SRD 5.4.1.jpg|500px|border]]

==STATEMENT OF WARRANTY==

'''Statement of Warranty'''

Battery Handling Systems, Inc. and its subsidiaries and affiliates (collectively “BHS”) warrants to the original purchaser of its equipment, that the equipment shall be free from defects in material and workmanship under normal and proper use, operation, and maintenance during the applicable warranty period set forth below for the product containing the alleged defect:

<ul>
<li>Thirteen (13) months from the date of shipment to the original purchaser with respect to frames, weldments, electric drives, motors (except brushes), motor driven pumps, valves, and drive wheel assemblies (except wheels) only.</li>

<li>Ninety (90) days from the date of shipment to the original purchaser with respect to all other parts not covered above.</li>

<li>Bulbs, fuses, and filters are not included in this ninety (90) day warranty, unless found to be defective prior to use or within (90) days of shipment to the original purchaser, whichever occurs first. 

BHS’s warranty obligations hereunder are contingent upon the following conditions: (1) BHS or its authorized dealer is promptly (but in no event later than thirty (30) days following the discovery of the claimed defect) notified of the defect; (2) the purchaser establishes to BHS’s reasonable satisfaction that any goods have been properly installed, maintained, and operated; (3) the purchaser returns the defective goods or any part thereof to BHS; and (4) the purchaser complies with all other warranty procedures required by BHS (such procedures are available upon request). Upon a determination by BHS that a product is defective within the above-mentioned warranty period(s), BHS may, at its exclusive option, either provide parts and labor to repair or replace said defective equipment, or grant a credit or refund of the purchase price of the defective equipment. Repaired or replacement equipment and parts will carry the foregoing warranty for the remainder of the original warranty period or ninety (90) days from the date of shipment of the repaired/replaced equipment, whichever is longer.</li>
</ul>

BHS will cover normal ground freight charges such as ground UPS, common carrier, etc. for the delivery of repaired or replaced equipment or parts covered by this warranty. The cost of any express delivery, if requested, will be the sole responsibility of the purchaser, and the purchaser agrees to provide its account number with its preferred carrier to BHS or to pay the entire cost of express delivery as a condition of BHS’s provision of such express delivery. Unless expressly authorized in writing by BHS, the foregoing warranty does not cover the cost of removal or reinstallation of equipment (or the cost of other activities ancillary thereto), the cost of which will be borne solely by the purchaser.

This warranty is void in the case of abuse, misuse, abnormal use, accidents, overloading, improper installation, repair, or maintenance (other than by BHS), modification of products, application of products not in accordance with the instruction manual and product application bulletins, or any other reason BHS determines that said product is not operating properly as a result of causes other than defective manufacture.

This warranty shall apply exclusively to products sold to the purchaser by BHS. BHS shall not have any liability or obligation to the purchaser, under this warranty or other- wise, with respect to any defect or failure of performance in products which are not sold or manufactured by BHS, including any such products which are commingled with or incorporated into any BHS products, or any products into which BHS products are incorporated as a system component or otherwise without the prior written approval of BHS. This warranty does not cover accessories and attachments not manufactured by BHS. The original manufacturer’s warranty, if any, for such accessories or attachments takes precedence and all claims shall be directed to their respective manufacturers.

ANY LITIGATION TO ENFORCE THE FOREGOING WARRANTY MUST BE COMMENCED NO LATER THAN ONE (1) YEAR AFTER DISCOVERY REASONABLY SHOULD HAVE BEEN MADE OF ANY FACTS OR OTHER INFORMATION SUGGESTING THE EXISTENCE OF A PRODUCT FAILURE OR A PRODUCT DEFECT. THE WARRANTY SET FORTH HEREIN IS THE COMPLETE AND ENTIRE WARRANTY MADE BY BHS AND ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MER- CHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, NON-INFRINGEMENT, OR OTHERWISE, ARE HEREBY EXPRESSLY EXCLUDED. NO PERSON IS AUTHORIZED TO MAKE ANY OTHER OR ADDITIONAL WARRANTY ON BEHALF OF BHS. THE RIGHT TO REPAIR, REPLACEMENT, OR CREDIT/REFUND, AS SET FORTH HEREIN, IS THE SOLE AND EXCLUSIVE REMEDY FOR BREACH OF THE ABOVE WARRANTY. BHS SHALL NOT BE LIABLE FOR CHARGES OR EXPENSES OF ANY NATURE UNDER THE FOREGOING WARRANTY INCURRED WITHOUT BHS’S CONSENT. FURTHER, UNDER NO CIRCUMSTANCES, REGARDLESS OF THE FORM OF THE CLAIM OR CAUSE OF ACTION (WHETHER IN WARRANTY, CONTRACT, INFRINGEMENT, NEGLIGENCE, STRICT LIABILITY, OR FOR ANY OTHER TORT OR CLAIM), SHALL BHS BE LIABLE TO THE PURCHASER OR ANYONE ELSE FOR ANY: (A) INCIDENTAL DAMAGES (EXCEPT AS SPECIFICALLY PROVIDED FOR ABOVE), OR CONSEQUENTIAL, INDIRECT, SPECIAL OR PUNITIVE DAMAGES RELATIVE TO OR ARISING FROM OR CAUSED DIRECTLY OR INDIRECTLY BY SAID PRODUCTS OR THE USE THEREOF OR ANY DEFICIENCY, DEFECT, OR INADEQUACY OF SAID PRODUCTS; OR (B) DIRECT DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE BHS EQUIPMENT GIVING RISE TO THE CLAIM OR CAUSE OF ACTION, OR AT THE ELECTION OF BHS, THE RESTORATION OR REPLACEMENT OR REPAIR OF SUCH EQUIPMENT. “CONSEQUENTIAL DAMAGES” INCLUDE, WITHOUT LIMITATION, LOST PROFITS, BUSINESS INTERRUPTION DAMAGES, LOSS OF USE DAMAGES, AND DAMAGE TO REPUTATION OR GOODWILL.
This Warranty is governed by and construed in accordance with the laws of the State of Missouri, without regard to conflict of law principles. All disputes or controversies arising out of or in connection with this Warranty shall be subject to the exclusive jurisdiction of the U.S. District Court for the Eastern District of the State of Missouri and any and all process in connection with any litigation arising out of such dispute or controversy may be served by registered, certified mail, return receipt requested, outside Missouri, with the same force and effect as if service had been made in Missouri.

If part of this Warranty is held to be invalid or unenforceable, such invalidity or unenforceability shall not invalidate or render unenforceable the entire Warranty, but rather the Warranty shall be construed as if not containing the particular invalid or unenforceable provision.

== WARRANTY PROCEDURES ==
'''Warranty Procedures'''

Please refer to '''Battery Handling Systems, Inc.'s''' Statement of Warranty and Liability (which is set forth on the reverse side hereof or available upon request) for a complete description of '''BHS'''' warranty. In the event of conflict between '''BHS'''' warranty and these procedures, the warranty will control.

'''Battery Handling Systems, Inc.'s''' warranty policy is intended to protect original purchasers who submit valid claims, as well as to identify and eliminate claims where product failure is the result of customer abuse, neglect or misapplication.

'''Step 1: Gather Information'''

The following information must be provided immediately.

<ul>
<li>A description of the product that includes, at a minimum, the model, serial number, and hour meter reading (if applicable).</li>
<li>Customer name, location, and contact information including phone number.</li>
<li>Installation date, installation provider (dealer), servicing dealer, and selling dealer.</li>
<li>Any prior repairs, modification, or adjustments.</li>
</ul>

'''Step 2: Contact BHS'''

Contact '''BHS''' at:

Phone: 1.877.247.4968 
Fax: 1.314.423.5948 
Email: service@bhs1.com

'''Step 3: Authorization'''

BHS will authorize further evaluation, repair, or replacement. A warranty claim form indicating '''BHS''' prior authorization for any such action will be issued to claimant. The completed warranty claim form must be submitted with any request for warranty credit.

'''Step 4: Request RGA Number'''

<ul>
<li>Suspected defective parts must be returned to '''BHS''' under an issued Return Goods Authorization (RGA) number.</li>
<li>BHS will specify the proper disposition of the parts through the issue of an RGA number.</li>
<li>Return shipment method will also be specified at time of RGA issue. RGAs are good for thirty (30) days from date issued; no credit will be issued for items returned after the RGA has expired.</li>
</ul>

'''Step 5: Claim Warranty'''

<ul>
<li>Submit Warranty Claim forms and supporting documents to: Battery Handling Systems, Inc. 
P.O. Box 28990 
St. Louis, MO 63132 
Fax: 1.314.423.5948 
Email: service@bhs1.com</li>
<li>Labor allowance hours are determined by our engineering staff.</li>
<li>Actual travel time, labor time, and parts costs must be indicated as separate items as provided on the form.</li>
</ul>

'''Step 6: BHS will process warranty claim and notify purchaser of final disposition.'''

Main Page

2026-01-27T12:12:54Z

Mbowen: /* Battery Handling Equipment */

=<big>BHS Product Manuals</big>=

== <big>North America</big> ==

=== Battery Handling Equipment ===
*[[IOP-080 Automatic Transfer Carriage (ATC) Parts & Service Manual|(ATC) Automatic Transfer Carriage - Parts & Service Manual]]
*[[Battery Extractor Series Reports|(BE) Battery Extractor Series - Planned Maintenance Inspection Reports]]
*[[IOP-403 BE-36-1-SS|(BE-SS) Single Side Battery Extractor - Parts & Service Manual]]
*[[(BE-SL & -DS) Single Level & Double Stack Operator Aboard Battery Extractors – Parts & Service Manual (IOP-400)|(BE-SL&DS) Single Level and Double Stack Operator Aboard Battery Extractors - Parts & Service Manual]]
*[[IOP-406SLN&DSN|(BE-SLN & DSN) Single Level and Double Stack Competitor Replacement Battery Extractors - Parts & Service Manual]]

*[[(BE-TS) Triple Stack Operator Aboard Battery Extractors – Parts & Service Manual (IOP-401)|(BE-TS) Triple Stack Operator Aboard Battery Extractors - Parts & Service Manual]]
*[[IOP-407 BE-TSN|(BE-TSN) Triple Stack Competitor Replacement Battery Extractors - Parts & Service Manual]]

*[[IOP-402 BE-QS|(BE-QS) Quad Stack Operator Aboard Battery Extractors - Parts & Service Manual]]
*[[IOSM-240 BLB|(BLB) Battery Lifting Beam - Parts & Service Manual]]
*[[IOP-128 BT16-2|(BT16-2) Bridge Trolley - Parts & Service Manual]]
*[[IOP-050 BTC|(BTC) Battery Transfer Carriage - Parts & Service Manual]]
*[[IOM-421 BWC-1|(BWC-1) Battery Wash Cabinet with Manual Door & Gravity Feed Rollers - Parts & Service Manual]]
*[[IOM-422 BWC-2 & BWC-3|(BWC-2 & BWC-3) Battery Wash Cabinet with Automatic Door & Powered Rollers - Parts & Service Manual]]

*[[Fleet Tracker User Manual|(FLT) Fleet Tracker User Manual]]

*[[Fleet_Tracker_IIOT_User_Manual |(FLT-IIOT) Fleet Tracker – IIOT - User Manual]]
*[https://tech.bhs1.com/index.php/IOP-495_FST-330_Operating_Instructions (FST-330) Battery Watering & Filling System Tank Operating Instructions]
*[[IOP-350 (MBE-42)|(MBE-42) Mobile Battery Extractor - Parts & Service Manual]]
*[[IOP-146 PGC-PDC|(PGC-PDC) Power Drive Gantry Crane - Parts & Service Manual]]
*[[IOP-425 RNS-1|(RNS-1) Recirculation/Neutralization System, 125 Gallon - Parts & Service Manual]]

*[[IOP-426 RNS-4-SS|(RNS-4-SS) Recirculation/Neutralization System, Stainless Steel, 200 Gallon, Auto pH Monitoring - Parts & Service Manual]]

*[[IOP-427 RNS-3-SS|(RNS-3-SS) Recirculation/Neutralization System, Stainless Steel, 200 Gallon - Parts & Service Manual]]

*[[IOM-078 WTC |(WTC) Walkie Transfer Carriage - Parts & Service Manual]]

=== Material Handling Equipment ===

*[[IOP-29401001 Lift Table Ladder|(LTL) Lift Table Ladder - Parts & Service Manual]]
* [https://tech.bhs1.com/index.php/IOP-276_MMLT (MMLT) Mobile Manual Lift Table - Parts & Service Manual]
* [https://tech.bhs1.com/index.php/IOP-PCP-P_Manual#Pallet_Carousel_%26_Positioner_with_Self-Leveling_Pneumatic_Airbag_-_Parts_%26_Service_Manual (PCP-P) Pallet Carousel & Positioner with Self-Leveling Pneumatic Airbag]
* [https://tech.bhs1.com/index.php/IOP-60701004_Powered_Dock_Gate (PDG) Powered Dock Gate - Parts & Service Manual]
* [[IOP-265 SRD|(SRD) Shipping and Receiving Desk - Parts & Service Manual]]
* [https://tech.bhs1.com/index.php/IOP-TCD-1_Manual (TCD) Tilt Cart Dumper - Parts & Service Manual]
* [[IOP-620 - YARD RAMP|(YR) Yard Ramp - Parts & Service Manual]]

=== Electrical Handling Equipment ===

* [[IOP-SWT|(SWT) Spool Winding Trolley - Operational Manual]]

*[[IOP-ORL OPERATING INSTRUCTIONS|(ORL) Overhead Reel Lifter - Operating Instructions]]

*[[IOP-RHA OPERATING INSTRUCTIONS|(RHA) Reel Handler Attachment - Operating Instructions]]

== <big>International</big> ==

(BE-SL & -DS) Single Level & Double Stack Operator Aboard Battery Extractors – Parts & Service Manual (IOP-400)

2026-01-09T15:31:59Z

Mbowen: /* [Discontinued] Helical Actuator (Prior to July 2023) */

'''Looking for a specific replacement part?''' Ctrl-F (or Command-F for Mac users) brings up your browsers search panel and can search any text on the entire web page. Find parts by searching a part # or part description.

'''Register your equipment with [https://na.bhs1.com/media-library/bhs-optima/ BHS Optima], BHS's free app.'''

'''California Residents''': WARNING: This product contains chemicals known to the State of California to cause cancer and/or reproductive harm, and birth defects or other reproductive harm. [https://na.bhs1.com/about-bhs/compliance-statement-for-california-proposition-65/ Learn more here.]

= <big>Preface</big> =
This manual is to be used to service '''SINGLE LEVEL (BE-SL)''' as well as '''DOUBLE STACK (BE-DS)''' Battery Extractors.

Any views not specifically stated otherwise are of the Single Level Extractor. The parts listed are common for Single Level (BE-SL) and Double Stack (BE-DS) unless otherwise noted in the notes column of the Parts Lists. ''See Example Below''.
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="2" |1
|00158001-10
|CHAIN-ROLLER-#60
|
|''BE-SL Only''
|4
|-
|00158001-12
|CHAIN-ROLLER-#60
|
|''BE-DS Only''
|4
|}
For Items or Assemblies that are unique to only the SL or DS, it will be designated as such on the diagram and have a separate, corresponding parts list for that diagram.

When servicing '''HIGH PERFORMANCE (BE-DS-HP)''' models, refer to the [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#High_Performance_Options High Performance Option] section for all parts unique to High Performance Units. If a particular part is not found in the [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#High_Performance_Options High Performance Option] section, refer tot the Standard Parts Section(s) of this manual.

= <big>TP-606 – Safety & De-Energization Procedures</big> =

== <big>General Safety</big> ==
{|
| [[File:Read Before Operating Notice.png|alt=Read Before Operating|frameless|120x120px|link=https://tech.bhs1.com/index.php/File:Read_Before_Operating_Notice.png]]
|
*Read and understand all instructions and warnings before using or servicing this equipment.
*Keep these instructions for future reference.
|}

* Battery Extractor (BE) units shall only be operated by suitable persons of at least 18 years of age, who have been trained in the proper and safe operation of the BE and expressly certified/charged, in writing, by the user or their representative.
* Only one person is permitted to travel on the BE at any time.
* BE units shall only be used indoors in an industrial setting on a hard, nonslip, and level floor without defects including but not limited to holes, gouges, cracks, drains or obstacles comprised of concrete or other suitable industrial material meeting the minimum requirements specified by BHS as well as any local requirements.
* A licensed structural engineer should be consulted prior to installing a BE on any building level other than the ground floor.
* BE units are not designed to be shipped or transported after initial delivery.
* Failure to follow these instructions and warnings may result in property damage, personal injury or death.

=== <big>Work Area</big> ===

* Keep work area clean and well lit. Cluttered work areas and poor lighting can lead to accidents.
* Clean up/contain any fluid spills immediately to prevent slips or falls.
* Be aware of potential hazards when performing any service or maintenance to the unit.

===<big>Service & Maintenance</big>===
Service personnel shall wear Personal Protective Equipment (PPE) appropriate for the task being performed.
{|
|[[File:Electrical Hazard Warning.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Electrical_Hazard_Warning.png]]
[[File:Danger Warning.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Danger_Warning.png|alt=DANGER]]
|
===<big>Lockout/Tagout</big>===
'''Lockout/tagout the BE per your corporate policy, if damaged or not functioning properly. Lockout/tagout and de-energize all systems prior to performing any maintenance or service to unit.'''
|}
{|
|[[File:Warning-Battery-Explosion.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Warning-Battery-Explosion.png]]
[[File:Danger Warning.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Danger_Warning.png|alt=DANGER]]
|
===<big>Lead-Acid Battery Explosion Hazard</big>===
'''DO NOT allow open flames or sparks of any kind near a battery. Highly explosive gas is generated when charging a battery that can remain in battery cells for extended periods of time after charging is complete.'''
*Always wear appropriate PPE including rubber apron, gloves, boots and full face shield when performing service or maintenance to any lead-acid batteries.
*DO NOT place metal or other conductive objects on top of battery. Arcing may occur causing damage to the battery and/or serious personal injury or death.
*Use only chargers matching the voltage and amperage of the battery being charged. Overcharging a battery can cause damage to the battery, charger and/or serious personal injury or death.
*Turn off charger before disconnecting battery from charger. Arcing between battery and charger connectors can cause damage to the connectors and/or serious personal injury or death.
|}
{|
|[[File:Warning-Hydrualic-Hazard.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Warning-Hydrualic-Hazard.png]]
[[File:Warning.png|alt=WARNING|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Warning.png]]
|
===<big>Hydraulic Hazards</big>===
'''AVOID HIGH PRESSURE FLUIDS-Escaping fluid under pressure can penetrate the skin causing serious injury. Relieve pressure before disconnecting hydraulic lines. Tighten all connections before applying pressure. Keep hands and body away from pin holes which eject fluids under high pressure. Use a piece of cardboard or paper to search for leaks. DO NOT use your hand.'''

'''Any fluid injected into the skin under high pressure should be considered a serious medical emergency despite an initial normal appearance of the skin. There will be a delayed onset of pain, and serious tissue damage may occur. Medical attention should be sought immediately.'''
|}
{|
![[File:No Pacemakers Notice.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:No_Pacemakers_Notice.png]][[File:Strong Magnet Field Hazard Warning.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Strong_Magnet_Field_Hazard_Warning.png]]
[[File:Warning.png|alt=WARNING|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Warning.png]]
|
===<big>Electromagnet Hazard</big>===
'''Units equipped with magnetic extraction generate strong magnetic fields. Persons with pacemakers SHOULD''' '''NOT''' '''operate or be in close proximity to equipment during operation.'''

'''Failure to comply with this direction''' '''could result in serious personal injury or death.'''
|}

=== <big>Operational Safety</big> ===

* Only personnel trained in the proper and safe operation of BE units may operate or service the BE.
* Operators shall wear appropriate PPE suitable for working with industrial lead-acid batteries while operating the BE ''(See [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Lead-Acid_Battery_Explosion_Hazard Lead-Acid Battery Explosion Hazard] section).''
* All data plates, warning labels, placards, etc. shall be in place and legible at all times. Contact BHS for re-placement data plates, warning labels, placards or instructions.
* All users and service personnel shall be familiar with the meaning and risks associated with all data plates, warning labels, etc.
* All operators and service personnel shall be aware of potential crush and shear points while operating or servicing the BE.
* Keep hands and arms inside the operator compartment while operating the BE.
* Remove BE from service if damaged, defective, or operating improperly (or becomes such while operating) until repairs can be made to correct any problem(s).
* All operators shall be aware of the location of the end stops in the travel path to prevent driving the BE into the end stops.

=== <big>Do's and Don'ts</big> ===

* '''DO NOT''' exceed the maximum capacity of the BE.
* '''DO NOT''' modify or fit the BE with attachments without prior, written approval from BHS.
* '''DO NOT''' perform any maintenance or service to the BE with a battery loaded on the BE.
* '''DO NOT''' allow anyone to ride in or on the BE.
* '''DO NOT''' operate the BE with any guard or cover removed unless required for maintenance or repair.
* Disconnect the BE from all power sources before attempting to perform service or maintenance to the unit.
* '''DO NOT''' drive the BE into the end stops.
* '''DO NOT''' operate the BE if disengaged from the guidance track.
* '''DO NOT''' allow a battery to exit the BE when a lift truck or battery stand is not present to accept the battery.
* '''DO NOT''' rotate the arm onto a battery such that any part of the extractor arm, vacuum cup or magnet contacts the top of the battery.
* '''DO NOT''' allow anyone to enter the area under the carriage without the service stands properly installed.
* '''DO NOT''' use the BE in a manner for which it is not intended. Some examples of prohibited use are but not limited to:
** To transport people
** As a vehicle jack
** To lift loads greater than its rated load capacity
** Where unintentional movement may exist
** Having direct contact with foodstuffs
** In a potentially explosive atmosphere

== <big>De-Energization</big> ==
1. Fully lower the BE roller bed or position the roller bed on service stands if service requires the bed be raised. See Figures 1 & 2.
{|
|[[File:WARNING-warn.png|alt=WARNING|frameless|100x100px]]
!Failure to properly support the roller bed when performing service under the BE could result in injury from the roller bed lowering unexpectedly.
|}
[[File:IOP-400 BE-SL&DS (10-23) Fully Lower BE Roller Bed.png|alt=Fully lowered BE roller bed|none|thumb|FIGURE 1]]
[[File:IOP-400 BE-SL&DS (10-23) BE Roller Bed on Service Stands .png|alt=Raised BE roller bed positioned on service stands|none|thumb|FIGURE 2]]
2. Turn key on dashboard to the “OFF” position. See Figure 3.
[[File:IOP-400 BE-SL&DS (10-23) De-Energization Figure 3.png|alt=Key on BE-SL & BE-DS dashboard turned to the “OFF” position.|none|thumb|FIGURE 3]]
3. Disconnect power to the extractor or shut off the electrical branch circuit breaker.
{|
|[[File:Danger Warning.png|alt=DANGER|frameless|100x100px]]
|'''Failure to disconnect electrical power to the BE could result in electrical shock. Serious personal injury or death will occur.'''
|}
4. Actuate all hydraulic levers in both directions to re-lease any stored hydraulic pressure. See Figure 4.
{|
|[[File:WARNING-warn.png|alt=WARNING|frameless|100x100px]]
|'''Failure to release any stored hydraulic pres-sure could result in injury from:'''
* '''Escaping hydraulic fluid under high pressure (see ''[https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Operational_Safety HYDRAULIC HAZARDS]'' in the ''[https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#General_Safety GENERAL SAFETY]'' section).'''
* '''Unexpected movement of hydraulic components.'''
|}
[[File:IOP-400 BE-SL&DS (10-23) Actuate all Hydraulic Levers in Both Directions.png|alt=Actuate all hydraulic levers in both directions to release any stored hydraulic pressure.|none|thumb|FIGURE 4]]

== <big>Labels & Placards</big> ==
'''Operators should be familiar with the meaning of the following labels and placards found on the BE to ensure proper and safe operation.'''
{| class="wikitable"
|-
![[File:Read Before Operating Notice.png|alt=Read Before Operating|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:Read_Before_Operating_Notice.png]]
|'''Read and understand instruction manual prior to use.'''
|-
![[File:Lockout-Before-Servicing-Notice.png|alt=Lockout Before Servicing Unit|frameless|150x150px]]
|'''Lockout before servicing.'''
|-
![[File:IOP-400 BE-SL&DS (10-23) Extractor Arm Positioning Arrows.png|alt=BE-SL & BE-DS Extractor Arm Positioning Arrows|frameless|150x150px]]
|'''Extractor arm positioning arrows'''
|-
![[File:Do Not Operate Without Guards or Covers Notice.png|alt=DO NOT Operate Without Guards or Covers Notice|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:Do_Not_Operate_Without_Guards_or_Covers_Notice.png]]
|'''DO NOT operate with guards or covers removed'''
|-
![[File:IOP-400 BE-SL&DS (10-23) No Riders Allowed.png|alt= No riders allowed|frameless|150x150px]]
|'''NO riders allowed.'''
|-
![[File:No Pacemakers Notice.png|alt=DO NOT operate by or in close proximity to people with pacemakers.|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:No_Pacemakers_Notice.png]]
|'''DO NOT operate by or in close proximity to people with pacemakers.'''
|-
![[File:Strong Magnet Field Hazard Warning.png|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:Strong_Magnet_Field_Hazard_Warning.png]]
[[File:Warning.png|alt=WARNING|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:Warning.png]]
|'''Strong Magnet Field Hazard'''
* Attraction between magnet and metallic objects can crush.
* Keep unsecured metallic objects away from magnet.
* De-energize and lockout/tagout before servicing.
|-
![[File:Chain Entanglement Hazard Warning.png|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:Chain_Entanglement_Hazard_Warning.png]]
[[File:Warning.png|alt=WARNING|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:Warning.png]]
|'''Chain Entanglement Hazard'''
* Moving chains and sprockets can crush and cut.
* Keep hands and fingers clear. Do not operate with guards removed.
* De-energize and lockout/tagout before servicing.
|-
![[File:Electrical Hazard Warning.png|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:Electrical_Hazard_Warning.png]]
[[File:Danger Warning.png|alt=DANGER|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:Danger_Warning.png]]
|'''Electrical Hazard'''
* Energized components can cause electrical shock.
* De-energize and lockout/tagout before servicing.
|-
![[File:BE-SL and BE-DS Power Off-On.png|alt=BE-SL and BE-DS Power Off-On|frameless|180x180px]]
|'''Power Off/On'''
|-
![[File:IOP-400 BE-SL&DS (10-23) Horn Control.png|alt=BE-SL and BE-DS Horn Control |frameless|180x180px]]
|'''Horn (If equipped)'''
|-
![[File:IOP-400 BE-SL&DS (10-23) Vacuum Control.png|alt=BE-SL and BE-DS Vacuum Control |frameless|180x180px]]
|'''Vacuum Off/On (If equipped)'''
|-
![[File:IOP-400 BE-SL&DS (10-23) Magnet Extraction.png|alt=BE-SL and BE-DS Magnet Off/On|frameless|180x180px]]
|'''Magnet Off/On (If equipped)'''
|-
![[File:IOP-400 BE-SL&DS (10-23) Powered Roller Cut Off Override.png|alt=BE-SL and BE-DS Powered Roller Cut Off Override|frameless|180x180px]]
|'''Powered Roller Cutout Override (If equipped)'''
|-
![[File:IOP-400 BE-SL&DS (10-23) Rack-Level-Assist.png|alt=BE-SL and BE-DS Rack Level Assist |frameless|180x180px]]
|'''Rack Level Assist Indicator (If equipped)'''
|}
{| class="wikitable"
! rowspan="3" |[[File:IOP-400_BE-SL&DS_(10-23)_Power_Rollers_and_Arm_Travel.png.png|alt=BE-SL & DS Powered Roller and Arm Travel Controls|frameless|504x504px]]
|'''Far Power Rollers'''
|-
|'''Arm Travel'''
|-
|'''Near Power Rollers'''
|}
{| class="wikitable"
|+''BE-SL & DS UNITS ONLY''
! colspan="3" |[[File:IOP-400 BE-SL&DS (10-23) BE-SL&DS Units Platform Controls.png|alt=BE-SL & DS Specific Controls|frameless|460x460px]]
|-
|Drive Forward/Reverse
|Platform Raise/Lower
|Arm Rotation Near/Far
|}
{| class="wikitable"
|+''BE-TS & QS UNITS ONLY''
![[File:IOP-400 BE-SL&DS (10-23) BE-TS & BE-QS Platform Raise and Lower Controls.png|alt=BE-TS & BE-QS Platform Raise and Lower Controls|frameless|240x240px]]
! colspan="2" |[[File:IOP-400 BE-SL&DS (10-23)BE-TS & BE-QS Specific Controls.png|alt=BE-TS & BE-QS Specific-Controls|frameless]]
|-
|Platform Raise/Lower
|Drive Foward/Reverse
|Arm Rotation Near/Far
|}

= <big>General Information</big> =
== <big>Specification Data</big> ==
[[File:IOP-400 BE-SL&DS (10-23) Specification Data.png|alt=IOP-400 BE-SL&DS (10-23) Specification Data|frameless|778x778px]]
{| class="wikitable"
! colspan="2" |NOTE: SINGLE LEVEL MACHINE SHOWN
!BE-24-2
!BE-36-2
!BE-42-2
|-
!A
|Overall Length
|130"
|154"
|166"
|-
!B
|Overall Width
|72"
|72"
|74"
|-
!C
|Overall Height (Single Level / Double Stack)
|65" / 90"
|65" / 90"
|65" / 90"
|-
!D
|Wheel Base
|95.75"
|119.75"
|131.75"
|-
!E
|Drive Wheel Center line
|53"
|53"
|53"
|-
!F
|Battery Compartment Width
|24"
|36"
|42"
|-
!G
|Ground Clearance
|.625"
|.625"
|.625"
|-
!H
|Minimum Roller Height
|6.5"
|6.5"
|6.5"
|-
!I
|Maximum Roller Height (Single Level / Double Stack)
|26.5" / 56"
|26.5" / 56"
|26.5" / 56"
|-
!J
|Aisle Requirement
|78"
|78
|80"
|}

=== <big>Single Level</big> ===
{| class="wikitable"
!SPECIFICATIONS (IMPERIAL / METRIC)
!BE-24-2-SL
!BE-36-2-SL
!BE-42-2-SL
|-
|TRAVEL SPEED
|0 to 190 ft/min / 0 to 0.97 m/s
|0 to 190 ft/min / 0 to 0.97 m/s
|0 to 190 ft/min / 0 to 0.97 m/s
|-
|RAISE - LOWER SPEED
|0 to 10 ft/min / 0 to 0.05 m/s
|0 to 10 ft/min / 0 to 0.05 m/s
|0 to 10 ft/min / 0 to 0.05 m/s
|-
|POWERED ROLLER SPEED
|0 to 37 ft/min / 0 to 0.19 m/s
|0 to 37 ft/min / 0 to 0.19 m/s
|0 to 37 ft/min / 0 to 0.19 m/s
|-
|ARM TRAVERSE SPEED
|0 to 20 ft/min / 0 to 0.10 m/s
|0 to 20 ft/min / 0 to 0.10 m/s
|0 to 20 ft/min / 0 to 0.10 m/s
|-
|ARM ROTATION TIME
|6 s to 8 s
|6 s to 8 s
|6 s to 8 s
|-
|DRAW BAR PULL / VACUUM

(12” / 305 MM ROUND CUP)
|1,000 lb / 454 kg
|1,000 lb / 454 kg
|1,000 lb / 454 kg
|-
|DRAW BAR PULL MAGNET*
|800 lb to 1,200 lb / 363 kg to 544 kg
|800 lb to 1,200 lb / 363 kg to 544 kg
|800 lb to 1,200 lb / 363 kg to 544 kg
|-
|VACUUM ATTACH TIME
|< 1 s
|< 1 s
|< 1 s
|-
|VACUUM RELEASE TIME
|< 1 s
|< 1 s
|< 1 s
|-
|INPUT VOLTAGE
|240/480 V / 3 ph / 60Hz
|240/480 V / 3 ph / 60Hz
|240/480 V / 3 ph / 60Hz
|-
|AC CURRENT DRAW
|20.2 / 10.1 A
|20.2 / 10.1 A
|20.2 / 10.1 A
|-
|AC CURRENT DRAW W/ ELECTRIC

DRIVE OPTION
|31.8 / 15.9 A
|31.8 / 15.9 A
|31.8 / 15.9 A
|-
|CONTROL CIRCUIT VOLTAGE
|120 V ac
|120 V ac
|120 V ac
|-
|HYDRAULIC POWER UNIT
|5 hp / 3.73 kW
|5 hp / 3.73 kW
|5 hp / 3.73 kW
|-
|HYDRAULIC POWER UNIT W/ ELECTRIC DRIVE OPTION
|8 hp / 5.97 kW
|8 hp / 5.97 kW
|8 hp / 5.97 kW
|-
|HYDRAULIC PUMP
|8 gal/min / 30 L/min
|8 gal/min / 30 L/min
|8 gal/min / 30 L/min
|-
|POWER UNIT
|Hydraulic, Variable Displacement
|Hydraulic, Variable Displacement
|Hydraulic, Variable Displacement
|-
|OPERATING PRESSURE
|1,500 psi / 103 bar
|1,500 psi / 103 bar
|1,500 psi / 103 bar
|-
|VACUUM PUMP
|1/3 hp / 0.25 kW
|1/3 hp / 0.25 kW
|1/3 hp / 0.25 kW
|-
|VACUUM
|21” Hg / 711 mbar
|21” Hg / 711 mbar
|21” Hg / 711 mbar
|-
|FULL LOAD CAPACITY
|10,000 lb / 4535 kg
|10,000 lb / 4535 kg
|10,000 lb / 4535 kg
|-
|WEIGHT (EMPTY)
|5,800 lb / 2631 kg
|6,200 lb / 2812 kg
|7500 lb / 3402 kg
|-
|TOTAL COMPARTMENT

ROLLERS / POWERED
|11/5
|11/5
|11/5
|-
|GUIDE TRACK
|2” x 2.5” Angle / 51 mm x 64 mm
|2” x 2.5” Angle / 51 mm x 64 mm
|2” x 2.5” Angle / 51 mm x 64 mm
|-
|OVERALL DIMENSIONS (L X W X H)
|130” x 72” x 70” /

3302 mm x 1829 mm x 1778 mm
|154” x 72” x 70” /

3912 mm x 1829 mm x 1778 mm
|171” x 74” x 70” /

4343 mm x 1880 mm x 1778 mm
|-
|VACUUM ARM REACH
|4.5” to 14” / 114 mm to 356 mm
|4.5” to 14” / 114 mm to 356 mm
|4.5” to 14” / 114 mm to 356 mm
|-
|VACUUM ARM REACH (HYDRAULIC EXTENSION) TRUCK SIDE
|9” to 23” / 229 mm to 584 mm
|9” to 23” / 229 mm to 584 mm
|9” to 23” / 229 mm to 584 mm
|-
|MAGNET ARM REACH (HYDRAULIC EXTENSION) TRUCK SIDE
|14” to 22” / 355 mm to 559 mm
|14” to 22” / 355 mm to 559 mm
|14” to 22” / 355 mm to 559 mm
|-
|WHEEL BASE
|95.75” / 2432 mm
|119.75” / 3042 mm
|134.5” / 3416 mm
|-
|DRIVE WHEEL CENTERLINE
|53” / 1346 mm
|53” / 1346 mm
|53” / 1346 mm
|-
|BATTERY COMPARTMENT WIDTH
|24” / 610 mm
|36” / 914 mm
|42” / 1067 mm
|-
|MAXIMUM BATTERY DIMENSIONS

(L X W X H)
|48” x 23” x 36” /

1219 mm x 584 mm x 914 mm
|48” x 35” x 36” /

1219 mm x 889 mm x 914 mm
|48” x 41” x 36” /

1219 mm x 1041 mm x 914 mm
|-
|MINIMUM BATTERY WIDTH

(WITH VACUUM / MAGNET)
|12” / 305 mm

6” / 152 mm
|12” / 305 mm

6” / 155 mm
|12” / 305 mm

6” / 155 mm
|-
|MINIMUM BATTERY LENGTH
|16.5” / 419 mm
|16.5” / 419 mm
|16.5” / 419 mm
|-
|MINIMUM BATTERY HEIGHT
|17.75” / 451 mm
|17.75” / 451 mm
|17.75” / 451 mm
|-
|GROUND CLEARANCE
|0.63” / 16 mm
|0.63” / 16 mm
|0.63” / 16 mm
|-
|ROLLER HEIGHT
|6.5” Min / 26.5" Max

165 mm Min / 673 mm Max
|6.5” Min / 26.5" Max

165 mm Min / 673 mm Max
|6.5” Min / 26.5" Max

165 mm Min / 673 mm Max
|}

=== <big>Double-Stack</big> ===
{| class="wikitable"
!SPECIFICATIONS (IMPERIAL / METRIC)
!BE-24-2-DS
!BE-36-2-DS
!BE-42-2-DS
|-
|TRAVEL SPEED
|0 to 190 ft/min / 0.97 m/s
|0 to 190 ft/min / 0.97 m/s
|0 to 190 ft/min / 0.97 m/s
|-
|RAISE - LOWER SPEED
|0 to 16 ft/min / 0 to 0.08 m/s
|0 to 16 ft/min / 0 to 0.08 m/s
|0 to 16 ft/min / 0 to 0.08 m/s
|-
|POWERED ROLLER SPEED
|0 to 37 ft/min / 0 to 0.19 m/s
|0 to 37 ft/min / 0 to 0.19 m/s
|0 to 37 ft/min / 0 to 0.19 m/s
|-
|ARM TRAVERSE SPEED
|0 to 20 ft/min / 0 to 0.10 m/s
|0 to 20 ft/min / 0 to 0.10 m/s
|0 to 20 ft/min / 0 to 0.10 m/s
|-
|ARM ROTATION TIME
|6 s to 8 s
|6 s to 8 s
|6 s to 8 s
|-
|DRAW BAR PULL / VACUUM

(12” / 305 MM ROUND CUP)
|1,000 lb / 454 kg
|1,000 lb / 454 kg
|1,000 lb / 454 kg
|-
|DRAW BAR PULL MAGNET*
|800 lb to 1,200 lb / 363 kg to 544 kg
|800 lb to 1,200 lb / 363 kg to 544 kg
|800 lb to 1,200 lb / 363 kg to 544 kg
|-
|VACUUM ATTACH TIME
|< 1 s
|< 1 s
|< 1 s
|-
|VACUUM RELEASE TIME
|< 1 s
|< 1 s
|< 1 s
|-
|INPUT VOLTAGE
|240/480 V / 3 ph / 60Hz
|240/480 V / 3 ph / 60Hz
|240/480 V / 3 ph / 60Hz
|-
|AC CURRENT DRAW
|20.2 / 10.1 A
|20.2 / 10.1 A
|20.2 / 10.1 A
|-
|AC CURRENT DRAW W/ ELECTRIC

DRIVE OPTION
|31.8 / 15.9 A
|31.8 / 15.9 A
|31.8 / 15.9 A
|-
|CONTROL CIRCUIT VOLTAGE
|120 V ac
|120 V ac
|120 V ac
|-
|HYDRAULIC POWER UNIT
|5 hp / 3.73 kW
|5 hp / 3.73 kW
|5 hp / 3.73 kW
|-
|HYDRAULIC POWER UNIT W/ ELECTRIC DRIVE OPTION
|8 hp / 5.97 kW
|8 hp / 5.97 kW
|8 hp / 5.97 kW
|-
|HYDRAULIC PUMP
|8 gal/min / 30 L/min
|8 gal/min / 30 L/min
|8 gal/min / 30 L/min
|-
|POWER UNIT
|Hydraulic, Variable Displacement
|Hydraulic, Variable Displacement
|Hydraulic, Variable Displacement
|-
|OPERATING PRESSURE
|1,500 PSI / 103 bar
|1,500 PSI / 103 bar
|1,500 PSI / 103 bar
|-
|VACUUM PUMP
|1/3 hp / 0.25 kW
|1/3 hp / 0.25 kW
|1/3 hp / 0.25 kW
|-
|VACUUM
|21” Hg / 711 mbar
|21” Hg / 711 mbar
|21” Hg / 711 mbar
|-
|FULL LOAD CAPACITY
|10,000 lb / 4535 kg
|10,000 lb / 4535 kg
|10,000 lb / 4535 kg
|-
|WEIGHT (EMPTY)
|6,000 lb / 2722 kg
|6,600 lb / 2994 kg
|7,800 lb / 3538 kg
|-
|TOTAL COMPARTMENT

ROLLERS / POWERED
|11/5
|11/5
|11/5
|-
|GUIDE TRACK
|2” x 2.5” Angle

51 mm x 64 mm
|2” x 2.5” Angle

51 mm x 64 mm
|2” x 2.5” Angle

51 mm x 64 mm
|-
|OVERALL DIMENSIONS (L X W X H)
|130” x 72” x 92”

3302 mm x 1829 mm x 2337 mm
|154” x 72” x 92”

3912 mm x 1829 mm x 2337 mm
|171” x 74” x 92”

4343 mm x 1880 mm x 2337 mm
|-
|VACUUM ARM REACH
|4.5” to 14” / 114 to 356 mm
|4.5” to 14” / 114 to 356 mm
|4.5” to 14” / 114 to 356 mm
|-
|VACUUM ARM REACH (HYDRAULIC EXTENSION)
|9” to 23” / 229 mm to 584 mm
|9” to 23” / 229 mm to 584 mm
|9” to 23” / 229 mm to 584 mm
|-
|MAGNET ARM REACH (HYDRAULIC EXTENSION) TRUCK SIDE
|14” to 22” / 355 mm to 559 mm
|14” to 22” / 355 mm to 559 mm
|14” to 22” / 355 mm to 559 mm
|-
|WHEEL BASE
|95.75” / 2432 mm
|119.75” / 3042 mm
|134.5” / 3417 mm
|-
|DRIVE WHEEL CENTERLINE
|53” / 1346 mm
|53” / 1346 mm
|53” / 1346 mm
|-
|BATTERY COMPARTMENT WIDTH
|24” / 610 mm
|36” / 915 mm
|42” / 1067 mm
|-
|MAXIMUM BATTERY DIMENSIONS

(L X W X H)
|48” x 23” x 34”

1219 mm x 584 mm x 864 mm
|48” x 35” x 34”

1219 mm x 889 mm x 864 mm
|48” x 41” x 34”

1219 mm x 1041 mm x 864 mm
|-
|MINIMUM BATTERY WIDTH

(WITH VACUUM / MAGNET)
|12” / 305 mm

6” / 152 mm
|12” / 305 mm

6” / 152 mm
|12” / 305 mm

6” / 152 mm
|-
|MINIMUM BATTERY HEIGHT
|17.75” / 451 mm
|17.75” / 451 mm
|17.75” / 451 mm
|-
|GROUND CLEARANCE
|0.63” / 16 mm
|0.63” / 16 mm
|0.63” / 16 mm
|-
|ROLLER HEIGHT
|6.5” Min / 56” Max

165 mm Min / 1422 mm Max
|6.5” Min / 56” Max

165 mm Min / 1422 mm Max
|6.5” Min / 56” Max

165 mm Min / 1422 mm Max
|}

== <big>Pre-Installation Check</big> ==

=== <big>Floor Conditions</big> ===
The floor is the single most critical area of the battery room. A bad floor can cause significant issues with the installation as well as downtime and maintenance problems with the extractor. The floor should be verified as to its minimum thickness and strength with user. As noted on the drawing, the specific requirement of flatness for your particular type of system is listed. Below is a chart stating floor requirements. If possible, especially on double stack and higher systems, a digital level should be used to shoot the grade for compliance with the specification. The floor should also be inspected for severe cracks or excessively wide expansion joints in the travel path of the machine. If floor drains are present, they must not have a grade to the opening that encroaches into the travel path.

F-min is a rating method used to evaluate the flatness and levelness of a floor designated as "defined travel path". For example, an F-min rating of 60 means that there is no more than .129" of variation in the transverse axis (wheels left to right) and .287" variation in the longitudinal axis (front to back) on the equipment.

To avoid potential damage to drive wheel assemblies, guide track, structural components, guide rollers and issues with the inner frame equalization the "defined travel path" of the Battery Extractor should meet or exceed the recommended F-min specification. See chart below for the model specifications
{| class="wikitable"
!Model
!F-Min
!+/- Longitudinal
!+/- Transverse
!Slope Defect
|-
|SL, DS
|40
|.287"
|.192"
|.096"
|-
|TS
|60
|.186"
|.129"
|.066"
|-
|QS
|85
|.131"
|.091"
|.047"
|}
[[File:IOP-400 BE-SL&DS (10-23) Floor Conditions Pre-Installation Check.png|alt=IOP-400 BE-SL&DS (10-23) Floor Conditions Pre-Installation Check|frameless|500x500px]]

== <big>Operating Controls & Instructions</big> ==

=== <big>Operating Controls</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Operator Console.png|alt=BE-SL Operator Console|frameless|1080x1080px]]

'''''NOTE''''': Safety devices for the machine and the machine operating area SHALL NOT be rendered inoperable or misused.

Typical BE-SL operator console shown above. Position of BE-DS and/or optional controls may vary from that shown depending on age of unit and/or combination of optional controls present.

HMI display standard on units shipped after February, 2020 for Industrial Internet of Things (IIoT) package.

==== <big>Safety Features</big> ====
Key Switch – Located on the dash (see [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Operating_Controls Operating Controls]above). Primary on/off switch to prevent unauthorized personnel from operating the BE.

Emergency Stop – Located on the dash (see [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Operating_Controls Operating Controls] above). Will stop all functions immediately, locking all hydraulics in place. To

use, press down on the red button. The machine key must be used to reset the emergency stop.

Foot Switch – Must be depressed to operate the BE. Stepping off the foot switch will stop all functions immediately, locking all hydraulics in place. To resume use, depress the foot switch.

Gate Switch – The gate must be fully closed for the BE to operate.

Extractor Arm Switch – Does not permit the machine to move forward or backward unless the extractor arm is located in the center of the carriage between the indicating arrows located on the arm guard.

Powered Roller Cutout (PRC-1 or PRC-2) (I''f equipped'') – Disengages the powered roller function when the photo eye positioned on the edge of the BE battery compartment is disrupted by a battery, requiring additional input from the operator. Pressing the "Power Roller Cutout" override button (see [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Operating_Controls Operating Controls]above) on the dash will resume powered roller operation when loading or unloading batteries from the BE carriage.

Horn (''If equipped'') – Button located on the dash (see [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Operating_Controls Operating Controls]above). Used to alert personnel before moving the BE.

Strobe Light (''If equipped'') – Located on a vertical stanchion mounted to the right rear of the operator compartment. For units equipped with optional overhead guard (OHG), the beacon is located above of the operator compartment. Beacon automatically flashes when the BE is switched on to visually notify the BE is in use.

Audible Alarm (''If equipped'') – Mounted in the same location as the Strobe Light. Automatically sounds when the BE is switched on to notify personnel that the BE is in use.

Blue Light (''If equipped'') - Mounted at an elevated position on either end of the extractor which project a bright, highly concentrated blue beam pattern on the ground visually alerting personnel to the direction the extractor is moving.

=== <big>Operation Overview</big> ===

* All operators should be familiar with the operator console of the extractor before performing any battery changes. The controls of the console are simple and well marked. It consists of six, manually operated, hydraulic control valves and a three position selector switch which controls the left and right vacuum cups (or optional magnets).
* The operator shall make certain there are no persons or obstacles in the extractor path prior to traveling forward or reverse.
* All manual valves are moved in the direction of the function travel which it controls with exception of the lift/lower valve, which is pulled toward the operator for "up" and pushed away for "down."
* In the event of any failure or malfunction, step off the dead-man switch or press the E-stop button and all functions will stop immediately, locking all hydraulics in place.
* The extractor arm must be in the center of the carriage or the unit will not travel forward or reverse.
* To ensure smooth operation, all valve movements should be made in a slow, deliberate motion.
* Only one key should be provided to operate the extractor.
* When leaving the machine, the operator shall turn off the key switch, remove the key and logout out of the IIoT (if equipped) to prevent unauthorized use
* Ensure all the batteries and cables are properly stored in the battery stands prior to moving the BE.
* The BE is designed to carry only one battery in each compartment on the carriage.
* When loading the BE, position the batteries in the center of the compartments on the powered rollers to prevent any battery movement when transporting.
* Ensure there are no projections outside of the carriage before moving the BE.

=== <big>Operating Instructions</big> ===

==== <big>Pre-Change Out Preparation</big> ====
1. Position lift truck for change out in designated area.

2. Remove all battery restraints and disconnect battery cables following manufacturers guidelines. (Be sure to position battery cables so as not to be damaged by the battery during change out.)

3. Board battery extractor and close safety gate. (Gate must be fully closed or unit will not operate.)

4. Turn key switch to "ON" position.

5. Log in on the HMI display (if equipped with BE-IIoT package).

6. Depress foot pedal.

==== <big>Discharged Battery Removal</big> ====
1. Move extractor forward or reverse to position center of empty compartment with center of lift truck battery compartment. (Lead roller of extractor is equipped with a centering groove. Users may find it beneficial to mark center of lift truck compartment to aid in alignment.)

2. Align extractor's roller compartment height with lift truck's battery compartment.

3. Rotate extractor arm into battery compartment aligned in Step 2.

4. Move extractor arm toward battery until vacuum cup/magnet contacts battery

[[File:NOTICE-warn.png|alt=NOTICE|frameless|120x120px]] '''DO NOT force cup/magnet into battery after initial contact with battery is made.'''

5. Energize vacuum/magnet by turning selector switch to proper direction, left or right.

6. Move extractor arm away from lift truck toward center of extractor roller bed, removing discharged battery. (Battery should be pulled past first three idler rollers onto first or second powered roller.)

7. Turn off vacuum/magnet and move extractor arm away from battery 1" to 2".

8. Rotate extractor arm out of battery compartment into opposite compartment (if empty) and center arm in carriage.

9. Move battery into center of compartment using powered rollers.

==== <big>Charged Battery Retrieval</big> ====
1. Locate charged battery for appropriate type of lift truck being changed.

2. Raise battery extractor roller compartment to proper level to gain access as needed to disconnect desired battery from its charger and disengage battery safety stop.

[[File:WARNING-warn.png|alt=WARNING|frameless|120x120px]] '''ALWAYS be sure charging has been completed and charger is not still charging battery. Dangerous sparking/arcing can occur if battery is unplugged from charger while charging.'''

3. Move extractor to appropriate rack position and align empty roller compartment with the center of the battery storage rack compartment. ''(The battery safety stop of each compartment is the center of that compartment and should be used for alignment with the groove in the lead roller of the battery extractor compartment.)''

4. Rotate arm into empty compartment (if not already positioned there.)

5. Move extractor arm toward battery until vacuum cup/magnet contacts battery.

6. Energize vacuum cup/magnet by turning selector switch to proper direction, left or right.

[[File:NOTICE-warn.png|alt=NOTICE|frameless|120x120px]] '''DO NOT force cup/magnet into battery after initial contact with battery is made.'''

7. Move extractor arm away from battery rack toward center of extractor roller bed, removing charged battery. (Battery should be pulled past first three idler rollers onto first or second powered roller.)

8. Turn off vacuum/magnet and move extractor arm away from battery 1" to 2".

9. Rotate extractor arm out of battery compartment into fully vertical position.

10. Move battery into center of compartment using powered rollers.

==== <big>Discharged Battery Return</big> ====
1. If required, adjust extractor compartment height to battery rack level with open battery compartment. Drive extractor to align roller compartment containing discharged battery with open battery compartment.

2. Return discharged battery to battery rack using powered rollers.

'''''NOTE:''' In most instances, batteries can be deposited into battery racks in one motion using only powered rollers. When this does not work, the battery may need slight assistance from extractor arm. To do this, rotate arm into compartment such as one would if removing battery from rack. If extractor is vacuum equipped, position top edge of cup slightly higher than edge of battery (or over lifting eye if so equipped) to prevent cup from adhering to battery - No vacuum/magnet is necessary for pushing. DO NOT activate vacuum/magnet switch. Slowly push battery into rack until fully into compartment.''

3. Engage battery safety stop and connect battery to charger as required.

==== <big>Charged Battery Installation</big> ====
1. Lower extractor to fully lowered position.

2. Drive extractor back to lift truck and align roller compartment containing charged battery as performed in steps 1 and 2 of [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)?venotify=created#Discharged_Battery_Removal ''Discharged Battery Removal''].

3. Move charged battery toward lift truck compartment by using powered rollers, verifying precise battery alignment.

[[File:NOTICE-warn.png|alt=NOTICE|frameless|120x120px]] '''Many batteries are a tight fit into lift truck battery compartments. Care MUST be taken to ensure alignment is precise to avoid damage to battery, lift truck, and/or battery extractor.'''

4. Adjust extractor vertically as well as horizontally, if needed.

5. Insert battery into lift truck as far as possible using only the powered rollers.

6. Rotate extractor arm into compartment and SLOWLY push battery into lift truck. (Be sure to watch battery cables for interference.)

7. Return extractor arm to center of roller bed and lower extractor to fully lowered position. Drive extractor out of immediate area.

8. Turn off key switch, remove key from switch, log out on the HMI display (if equipped with BE-IIoT package) and carefully exit extractor.

9. Secure newly installed battery in lift truck and reconnect battery cables.

10. Return lift truck to service.
{|
![[File:Caution-Warning.png|alt=CAUTION|frameless|120x120px]]

|'''DO NOT drive the BE into the travel path end stops. The end stops are designed to prevent the BE from accidentally traveling beyond its designated travel path. Driving the BE into the end stops will cause the BE to stop suddenly, possibly causing damage to the end stop, the BE and/or personal injury.'''
|}

==== <big>Optional Powered Roller Cutout Operation</big> ====
Units equipped with optional Powered Roller Cutout, the powered roller override button must be depressed in addition to actuating the hydraulic valve when a battery disrupts the photo eye(s) at the edge of the battery compartments while using the powered rollers to transfer batteries on and off of the battery extractor.

==== <big>IIoT Equipped Units</big> ====
Units shipped after February, 2020 are equipped with BEIIoT (Industrial Internet of Things) package.

Operators must log in to the BE-IIoT system using the HMI (Human Machine Interface) display located on the dashboard to operate the extractor.

When finished operating the extractor, the operator should log out of the BE-IIoT to prevent unauthorized access and/ or operation of the extractor.

== <big>Manual Unloading</big> ==
'''Lockout/tagout and de-energize all equipment prior to manually unloading any battery.'''

In the event of power loss or an operational malfunction of the BE not allowing a battery to be unloaded using normal operating procedures, it is recommended a battery be removed from the BE using certified and approved vertical extraction methods and devices.
{|
|[[File:DANGER-warn.png|alt=DANGER|frameless|120x120px]]
|'''Read, understand and observe all safety warnings and procedures related to the vertical extraction device(s) being used.'''
|}
Should the status of the BE not allow for safe vertical extraction (due to position in the battery aisle or level of the inner carriage), only repairs required to safely maneuver the BE to a position allowing for safe vertical extraction should be made. Once any batteries are safely unloaded, any remaining repairs can be made.
{|
|[[File:DANGER-warn.png|alt=DANGER|frameless|120x120px]]
|'''Extreme care should be taken when working under or around equipment supporting elevated loads. Unexpected movement of the equipment could cause the load and/or equipment to fall. ALWAYS be sure devices of adequate size and strength are in place to prevent any personnel working under the elevated load from being crushed. Serious personal injury or death will occur.'''
|}
== <big>Spare Parts List</big> ==
Refer to the appropriate Spare Parts Kit (vacuum equipped units - Pt# BE-SPKV-SLDS, magnet equipped units - Pt# BESPKM- SLDS) for the list of items recommended by BHS to have on hand for BE-SL or BE-DS models to minimize any downtime due to minor breakdowns that may occur under normal operating conditions.

Use only BHS approved replacement parts.

BHS offers many replacement parts kits containing relevant or related parts when replacing certain individual parts or replacing any obsolete / upgraded parts.

BHS also offers a supplement hose kit (Pt# 80242005) which contains an assortment of hoses allowing any hose on the extractor to be replaced immediately with a temporary hose of equal length or longer. After the extractor is back up and running, the failed hose can be taken to have an exact replacement made. Once the new hose is made and installed, the temporary hose can be returned to the kit for future use.

Go to [http://www.bhs1.com/ www.bhs1.com] and click "[https://na.bhs1.com/parts.html Parts]" for all the latest parts kits and corresponding installation instructions (if applicable).

BHS recommends that a full maintenance inspection report similar to the one provided be done at least once a month. Any parts found to be excessively worn or damaged should promptly be replaced unless said parts pose a safety risk to the operator and/or extractor, in which case the unit should be removed from service until the problem(s) are remedied (See Operator's Daily Checklist.)

'''''NOTE:''''' ''Spare parts kits contain parts for the most current machine design/configuration. Due to continuous design and manufacturing updates and improvements, not all the parts in the spare parts kits may be compatible with older units. Consult factory when ordering spare or replacement parts for existing units in the field to ensure part compatibility.''

= <big>Parts Sections</big> =

== <big>Chassis</big> ==

=== <big>Equalization Components</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Chassis Equalization.png|alt= BE-SL & BE-DS Chassis Equalization|frameless|564x564px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="2" |1
|00158001-10
|CHAIN-ROLLER-#60
|
|''BE-SL Only''
|4
|-
|00158001-12
|CHAIN-ROLLER-#60
|
|''BE-DS Only''
|4
|-
|2
|43097001
|STUD-ANCHOR-5"
|
|''Upper''
|4
|-
|3
|PT0222-1
|LINK-CONNECTING-#60
|
|
|8
|-
|4
|HW0115
|WASHER-LOCK-3/4"
|
|
|4
|-
|5
|HW0017
|NUT-HEX-3/4-10
|
|
|8
|-
|6
|43097002
|STUD-ANCHOR-2"
|
|
|4
|-
|7
|HW0020
|NUT-JAM-3/4-10
|
|
|4
|}
[[File:IOP-400 BE-SL&DS (10-23) Chassis Equalization 2.png|alt= BE-SL & BE-DS Chassis Equalization Detail A|frameless|597x597px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="4" |1
|43127001
|SHAFT-EQUALIZATION
|
|''BE-24-2''
|2
|-
|43327001
|SHAFT-EQUALIZATION
|
|''BE-36-2''
|2
|-
|44327001
|SHAFT-EQUALIZATION
|
|''BE-42-2''
|2
|-
|44527001
|SHAFT-EQUALIZATION
|
|''BE-42-1''
|2
|-
|2
|PT0405
|BEARING-FLANGE-2 BOLT-1 1/2"
|
|
|4
|-
|3
|HW0502
|BOLT-HHCS-1/2-13 X 1 1/4"
|
|
|8
|-
|4
|HW0110
|WASHER-LOCK-1/2"
|
|
|8
|-
|5
|PT0224
|SPROCKET-60B12 X 1 1/2"
|
|''Keyed Inline''
|8
|-
|6
|43097006
|KEY-3/8" X 2 3/4"
|
|
|4
|-
|7
|PT0416
|COLLAR-SHAFT-1 1/2"
|
|
|4
|-
| rowspan="2" |8
|PT0503
|BEARING-FLANGED LOAD-2 1/4"
|
|''Used on units after 12/03''
|8
|-
|43026001
|BEARING-FLANGED LOAD-2 1/4" (MACHINED)
|
|''Used on units prior to 12/03''
|8
|-
|9
|HW0025
|NUT-JAM-7/8-14
|
|
|8
|-
|10
|HW0117
|WASHER-LOCK-7/8" (NOT SHOWN)
|
|''Used on units prior to 08/02''
|8
|}

=== <big>Crossbar Detail</big> ===

==== <big>''BE-SL Crossbar Mounting''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL Crossbar Mounting.png|alt=BE-SL Crossbar Mounting|frameless|607x607px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HW0515
|BOLT-HHCS-1/2-13 X 2"
|
|''Fully Threaded''
|8
|-
|2
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|8
|-
|3
|HW0110
|WASHER-LOCK-1/2"
|
|
|8
|-
|4
|HW0007
|NUT-HEX-1/2-13
|
|
|8
|}

==== <big>'''''BE-DS Crossbar Mounting'''''</big> ====
[[File:BE-DS Crossbar Mounting.png|alt=BE-DS Crossbar Mounting|frameless|534x534px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HW0515
|BOLT-HHCS-1/2-13 X 2"
|
|''Fully Threaded''
|8
|-
|2
|HW0504
|BOLT-HHCS-1/2-13 X 2"
|
|
|8
|-
|3
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|8
|-
|4
|HW0110
|WASHER-LOCK-1/2"
|
|
|16
|-
|5
|HW0007
|NUT-HEX-1/2-13
|
|
|16
|-
|6
|43717040
|STOP-CARRIAGE
|
|
|4
|}

=== <big>Lift Cylinder Mounting and Connections</big> ===

==== '''<big>''BE-SL Lift Cylinder Connections''</big>''' ====
[[File:BE-SL Lift Cylinder Connections.png|alt=BE-SL Lift Cylinder Connections|frameless|582x582px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43617016
|CLEVIS
|
|
|4
|-
|2
|HW0403
|BOLT-HHCS-3/8-16 X 1 1/4"
|
|
|8
|-
|3
|HW0107
|WASHER-LOCK-3/8"
|
|
|8
|-
|4
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|8
|-
|5
|00197036
|PIN-CLEVIS
|
|
|4
|-
|6
|00197035
|PIN-CYLINDER
|
|
|4
|-
|7
|HW1058
|PIN-HITCH
|
|
|16
|}

==== <big>''BE-DS Lift Cylinder Connections''</big> ====
[[File:BE-DS Lift Cylinder Connections.png|alt=BE-DS Lift Cylinder Connections|frameless|569x569px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|00158001-11
|CHAIN-ROLLER-#80
|
|
|4
|-
|2
|HW0014
|NUT-HEX-1-8
|
|
|8
|-
|3
|43897002
|STUD-LIFT-INNER FRAME
|
|
|4
|-
|4
|PT0204-1
|LINK-CONNECTING-#80
|
|
|8
|-
|5
|43897001
|STUD-LIFT-OUTER FRAME
|
|
|4
|-
|6
|43715006
|BRACKET-CYLINDER SUPPORT
|
|
|4
|-
|7
|HW1043
|CLAMP-CYLINDER
|
|
|4
|-
|8
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|9
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|10
|HW0143
|WASHER-FLAT-1/4"-FENDER
|
|
|12
|-
|11
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|13
|00197035
|PIN-CYLINDER
|
|
|4
|-
|14
|HW1058
|PIN-HITCH
|
|
|8
|}

=== <big>Track Guidance Arms</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Guide Arm.png|alt=BE-SL & BE-DS Guide Arm|frameless|548x548px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
! colspan="2" |NO. REQ
|-
|1
|43015011
|GUIDE ARM WELDMENT, 2 ROLLER
|
|
|2
|<nowiki>-</nowiki>
|-
|2
|41215204
|GUIDE ARM WELDMENT, 4 ROLLER
|
|
|<nowiki>-</nowiki>
|2
|-
|3
|43012007
|CAM ROLLER-1 3/4"
|
|
|4
|8
|-
|4
|HW0115
|WASHER-LOCK-3/4"
|
|
|4
|8
|-
|5
|HW0011
|NUT-HEX-3/4-16
|
|
|4
|8
|-
|6
|HW0505
|BOLT-HHCS-1/2-13 X 3-1/2"
|
|
|4
|6
|-
|7
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|4
|6
|-
|8
|HW0110
|WASHER-LOCK-1/2"
|
|
|4
|6
|-
|9
|HW0007
|NUT-HEX-1/2-13
|
|
|4
|6
|-
|10
|41215234
|GUIDE ARM WELDMENT (POLY)
|
|
|2
|<nowiki>-</nowiki>
|-
|11
|41217317
|POLY SLIDE MOUNTING BLOCK
|
|
|4
|<nowiki>-</nowiki>
|-
|12
|41217318
|POLY SLIDE
|
|
|4
|<nowiki>-</nowiki>
|-
|13
|HW0501
|BOLT-HHCS-1/2-13 X 1"
|
|
|12
|<nowiki>-</nowiki>
|-
|14
|HW0110
|WASHER-LOCK-1/2"
|
|
|12
|<nowiki>-</nowiki>
|-
|15
|91253A546
|BOLT FHSCS-1/4-20 X 1-1/2"
|
|
|8
|<nowiki>-</nowiki>
|-
|16
|HW0003
|NUT-NILN-1/4-20
|
|
|8
|<nowiki>-</nowiki>
|-
! colspan="7" |NOTES
|-
| colspan="7" |''† Multiple styles of Guide Arms have been utilized on extractors. Refer to the parts diagrams for correct replacement parts.''
|}

=== '''<big>Roller Bed Components</big>''' ===

==== <big>''Idler Roller Bed Components''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Idler Rollers.png|alt=BE-SL & BE-DS Idler Rollers|frameless|600x600px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="3" |1
|43182001
|LEAD ROLLER ASSEMBLY-24"
|
|with Alignment Groove
|4
|-
|43382001
|LEAD ROLLER ASSEMBLY-36"
|
|with Alignment Groove
|4
|-
|43482001
|LEAD ROLLER ASSEMBLY-42"
|
|with Alignment Groove
|4
|-
| rowspan="3" |2
|43182002
|IDLER ROLLER ASSEMBLY-24"
|
|
|8
|-
|43382002
|IDLER ROLLER ASSEMBLY-36"
|
|
|8
|-
|43482002
|IDLER ROLLER ASSEMBLY-42"
|
|
|8
|-
| rowspan="3" |3
|43187002
|SHAFT-HEX-.75" X 25.75"
|
|
|8
|-
|43387002
|SHAFT-HEX-.75" X 37.75"
|
|
|8
|-
|43487002
|SHAFT-HEX-.75" X 43.75"
|
|
|8
|-
| rowspan="3" |4
|43187003
|SHAFT-HEX-.75" X 27.5"
|
|
|4
|-
|43387003
|SHAFT-HEX-.75" X 39.5"
|
|
|4
|-
|43487003
|SHAFT-HEX-.75" X 45.5"
|
|
|4
|-
|5
|HW1058
|PIN-HITCH
|
|
|24
|}

==== <big>'''''Powered Roller Bed Components'''''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Powered Rollers 1.png|alt=Powered Rollers|frameless|554x554px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="3" |1
|43182003
|POWERED ROLLER-24"
|
|
|10
|-
|43382003
|POWERED ROLLER-36"
|
|
|10
|-
|43485003
|POWERED ROLLER-42"
|
|
|10
|-
|2
|43087001
|JOURNAL-POWERED ROLLER
|
|
|10
|-
|3
|PT0404
|FLANGE BEARING-3-BOLT-1"
|
|
|20
|-
|4
|HW0321
|BOLT-HHCS-5/16-18 X 1 1/4"
|
|
|60
|-
|5
|HW0105
|WASHER-LOCK-5/16"
|
|
|60
|-
|6
|HW0004
|NUT-HEX-5/16-18
|
|
|60
|-
|7
|PT0033
|SPROCKET-35B18 X 1"
|
|
|16
|-
|8
|00197028
|KEY-1/4" X 1 1/4"
|
|
|8
|-
|9
|00158001-16
|CHAIN-ROLLER-#35
|
|
|8
|-
|10
|PT0031
|LINK-CONNECTING-#35
|
|
|8
|-
|11
|PT0418
|COLLAR-SHAFT-1"
|
|
|10
|}
[[File:IOP-400 BE-SL&DS (10-23) Powered Rollers 2.png|alt=Powered Rollers|frameless|524x524px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0120
|MOTOR-HYDRAULIC-160CC
|
|
|2
|-
|2
|HW1071
|KEY-WOODRUFF-#808 STD
|
|Supplied with Item 1
|A/R
|-
|3
|H1544
|ADAPTER-#6 JICM X #10 SAEM
|
|
|4
|-
|4
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|18
|-
|5
|HW0107
|WASHER-LOCK-3/8"
|
|
|18
|-
|6
|43017004
|PLATE-MOTOR MOUNTING
|
|
|2
|-
|7
|PT0302-1
|COUPLING BODY-#40 X 1"
|
|
|4
|-
|8
|PT0301
|CHAIN-COUPLING-#40
|
|Includes Connecting Pin
|2
|-
|9
|00197026
|KEY-1/4" X 1"
|
|
|2
|-
|10
|43097003
|KEY-1/4" X 5/8"
|
|
|2
|}

=== <big>Operator Gate</big> ===

==== <big>''[Discontinued] Drop Bar Operator Gate''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Drop Bar Barrier Gate.png|alt=Discontinued Drop Bar Operator Gate|frameless|565x565px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43015004
|GATE-OPERATOR-DROP BAR
|
|
|1
|-
|2
|HW0407
|BOLT-HHCS-3/8-16 X 2 3/4"
|
|
|1
|-
|3
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|2
|-
|4
|HW0006
|NUT-NILN-3/8-16
|
|
|1
|}

==== <big>'''''[Current] Swing-Style Operator Gate'''''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Operator Gates.png|alt=Operator Gate Styles|frameless|500x500px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43017064-2
|LATCH-SWING GATE
|
|
|1
|-
|2
|HW0418
|BOLT-HHCS-3/8-16 X 2 1/4"
|
|
|1
|-
|3
|HW0031
|NUT-LOCK-3/8-16, DEFORMED THREAD
|
|
|1
|-
|4
|N/A
|HINGE-SPRING
|
|''† See notes''
|1
|-
|5
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|3
|-
|6
|HW1037
|STOP-GATE
|
|
|1
|-
|7
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|1
|-
|8
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|1
|-
|9
|HW0003
|NUT-NILN-1/4-20
|
|
|1
|-
|10
|N/A
|SPRING-TORSION
|
|''† See notes''
|1
|-
|11
|HW0816
|SCREW-HHCS-SELF DRILLING-#10 X 3/4"
|
|
|4
|-
|12
|HW9002
|GAS SPRING
|80292015
|
|1
|-
|13
|43017086-2
|BRACKET-MOUNTING-SPRING
|80292015
|
|2
|-
|14
|HW0815
|SCREW-SELF DRILLING-#12-24 X 1" T-4
|80292015
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Part discontinued. Spring Hinge was replaced by Torsion Spring. Spring Hinge and/or Torsion Spring must be replaced with Gas Spring Kit.''
|}

=== <big>Operator Step</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Operator Step Styles.png|alt=BE-SL & BE-DS Operator Step Styles|frameless|525x525px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="2" |1
|43615012
|STEP
|
|''† BE-SL''
|1
|-
|43015007
|STEP
|
|''† BE-DS''
|1
|-
|2
|HW0406
|BOLT-HHCS-3/8-16 X 2 1/2"
|
|
|2
|-
|3
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|4
|-
|4
|HW0107
|WASHER-LOCK-3/8"
|
|
|2
|-
|5
|HW0005
|NUT-HEX-3/8-16
|
|
|2
|-
| rowspan="2" |6
|43606001
|ANTI-FATIGUE MAT
|
|''†† BE-SL''
|1
|-
|43706001
|ANTI-FATIGUE MAT
|
|''†† BE-DS''
|1
|-
|7
|43017058-2
|THRESHOLD
|
|
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Tread-Style Step is a direct replacement for Discontinued, Ladder Rung-Style Step.''
|-
| colspan="6" |''†† Anti-fatigue mat must be cut for units with foot switch bolted in place to floor panel.''
|}

=== <big>Hydraulic Hose Reel</big> ===

==== ''<big>[Discontinued] Hydraulic Hose Reel</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Hydraulic Hose Reel.png|alt=BE-SL & BE-DS Discontinued Hydraulic Hose Reel|frameless|556x556px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|PT0622-1
|HOSE REEL
|
|
|1
|-
|2
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|1
|-
|3
|HW0107
|WASHER-LOCK-3/8"
|
|
|1
|-
|4
|HW0005
|NUT-HEX-3/8-16
|
|
|1
|-
|5
|43717053-2
|BRACKET-HOSE REEL
|
|
|1
|}

==== ''<big>[Current] Hydraulic Hose Reel</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Current Hydraulic Hose Reel.png|alt= BE-SL & BE-DS Current Hydraulic Hose Reel|frameless|688x688px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|CCR-12HD
|HOSE REEL
|
|
|1
|-
|2
|43717122
|PLATE-MOUNTING
|
|
|1
|-
|3
|HW0413
|BOLT-FHSMS-3/8-16 X 1 1/4"
|
|
|2
|-
|4
|HW0517
|BOLT-HHCS-1/2-13 X 2 1/2"-FULL THREAD
|
|
|2
|-
|5
|HW0110
|WASHER-LOCK-1/2"
|
|
|2
|-
|6
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|2
|}

=== <big>Guarding</big> ===

==== <big>'''''BE-SL Guarding'''''</big> ====

===== ''BE-SL Outer Carriage Guards'' =====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL Outside Carriage Guard.png|alt= BE-SL Outside Carriage Guards|frameless|548x548px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43617006-2
|GUARD-FAR
|
|
|1
|-
|2
|43614009
|GUARD-NEAR
|
|
|2
|-
|3
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|30
|}

===== ''BE-SL Inner Carriage Guards (Rotary Actuator)'' =====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL Rotary Actuator Units Inner Guard.png|alt=BE-SL Rotary Actuator Units Inner Guards|frameless|530x530px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43617007-2
|GUARD-INNER CARRIAGE
|
|
|2
|-
|2
|43014006-2
|GUARD-LINEAR DRIVE SCREW
|
|
|1
|-
| rowspan="2" |3
|43017010-2
|GUARD-SIDE-ARM CARRIER SHAFT
|
|
|2
|-
|44517002-2
|GUARD-SIDE-ARM CARRIER SHAFT
|
|''† Single Compartment Units Only''
|1
|-
|4
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|32
|-
|5
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|4
|-
|6
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|7
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|8
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|9
|PL0602
|VINYL EDGING
|
|''6ft each for Item 3 (Not shown)''
|12'
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Single Compartment Guard Replaces standard, Far Side Arm Carrier Shaft Guard.''
|}

===== ''BE-SL Inner Carriage Guards (Helical Actuator)'' =====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL Helical Actuator Equipped Units Inner Guard.png|alt=BE-SL Helical Actuator Equipped Units Inner Guards|frameless|526x526px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43617007-2
|GUARD-INNER CARRIAGE
|
|
|2
|-
| rowspan="2" |2
|43017081-2
|GUARD-SIDE-ARM CARRIER SHAFT
|
|
|2
|-
|44517003-2
|GUARD-SIDE-ARM CARRIER SHAFT
|
|''† Single Compartment Units Only''
|1
|-
|3
|43017080-2
|BRACKET-SIDE GUARD MOUNTING
|
|
|2
|-
|4
|43017082-3
|MOUNT-CHAIN GUARD-LEAD SCREW
|
|
|1
|-
|5
|43017082-4
|MOUNT-CHAIN GUARD-LEAD SCREW
|
|
|1
|-
|6
|43017083-2
|GUARD-CHAIN-LEAD SCREW
|
|
|1
|-
|7
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|8
|HW0103
|WASHER-LOCK-1/4"
|
|
|8
|-
|9
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|8
|-
|10
|HW0347
|BOLT-BHSCS-1/4-20 X 3/8"
|
|
|4
|-
|11
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|26
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Single Compartment Guard replaces standard, Far Side Arm Carrier Shaft Guard.''
|}

==== <big>''BE-SL Dashboard Guards''</big> ====

===== ''[Discontinued] BE-SL Dashboard'' =====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued BE-SL Dashboard.png|alt=Discontinued BE-SL Dashboard|frameless|528x528px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43617038
|DASHBOARD
|
|''Used prior to October 2012''
|1
|-
|2
|43617039
|COVER PLATE
|
|
|2
|-
|3
|SS0104
|BOLT-SHCS-1/4-20 X 5/8"
|
|''Used prior to October 2012''
|18
|-
|4
|SS0300
|WASHER-FLAT-1/4"-SAE
|
|''Used prior to October 2012''
|18
|-
|5
|43614006-2
|KICK PLATE-OPERATOR CONSOLE
|
|
|1
|-
|6
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|14
|-
|7
|PL0602
|VINYL EDGING
|
|''Two 1ft pieces (Not shown)''
|2'
|}

===== ''[Current] BE-SL Dashboard'' =====
[[File:IOP-400 BE-SL&DS (10-23) Current BE-SL Dashboard.png|alt=Current BE-SL Dashboard|frameless|526x526px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43618017
|PLATE-DASHBOARD
|
|
|1
|-
|2
|HW0060
|NUT-CLIP-#10-24
|
|
|10
|-
|3
|SS0114
|BHSCS-#10-24 X 1/2" SST
|
|
|10
|-
|4
|43617039
|COVER PLATE
|
|
|2
|-
|5
|SS0126
|BHSCS-1/4-20 X 1/2"-SST
|
|
|8
|-
|6
|43614006-2
|KICK PLATE-OPERATOR CONSOLE
|
|
|1
|-
|7
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|10
|-
|8
|PL0602
|VINYL EDGING
|
|''Two 1ft pieces (Not shown)''
|2'
|}

==== ''<big>BE-SL Operator Platform Guards</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL Operator Platform Guards.png|alt=BE-SL Operator Platform Guards|frameless|591x591px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43617045
|PANEL-OPERATOR PLATFORM
|
|
|1
|-
|2
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|8
|-
|3
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|8
|-
|4
|HW0103
|WASHER-LOCK-1/4"
|
|
|8
|-
|5
|HW0002
|NUT-HEX-1/4-20
|
|
|8
|-
|6
|43606001
|MAT-ANTI FATIGUE
|
|''Not shown''
|1
|}

=== <big>'''BE-DS Guarding'''</big> ===

==== <big>'''''BE-DS Outer Carriage Guards'''''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-DS Outside Carriage Guards.png|alt=BE-DS Outside Carriage Guards|frameless|523x523px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43717017-2
|GUARD-FAR END-UPPER
|
|
|1
|-
|2
|43717019-2
|GUARD-FAR END-LOWER
|
|
|1
|-
|3
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|22
|}

==== ''BE-DS Inner Carriage Guards (Rotary Actuator)'' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-DS Rotary Actuator Equipped Units Inner Guards.png|alt=BE-DS Rotary Actuator Equipped Units Inner Guards|frameless|530x530px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43714001-2
|DASHBOARD
|
|''† See Notes''
|1
|-
| rowspan="2" |2
|43714016-2
|GUARD-FRONT-OPERATOR CONSOLE
|
|''†† Without Cylinder Notch''
|1
|-
|41217014-2
|GUARD-FRONT-OPERATOR CONSOLE
|
|''†† With Cylinder Notch''
|1
|-
|3
|43717016-2
|GUARD-INNER FRAME
|
|
|2
|-
|4
|43014006-2
|GUARD-LINEAR DRIVE SCREW
|
|
|1
|-
|5
|43017010-2
|GUARD-SIDE-ARM CARRIER SHAFT
|
|
|2
|-
|5a
|PL0602
|VINYL EDGING
|
|''6' each for Item 5 (Not shown)''
|12'
|-
| rowspan="2" |6
|43714015-2
|KICK PLATE-OPERATOR CONSOLE
|
|''35.5" tall''
|1
|-
|43717115-2
|KICK PLATE-OPERATOR CONSOLE
|
|''29" tall''
|1
|-
|6a
|PL0602
|VINYL EDGING
|
|''Two 1' pieces for Item 6 (Not shown)''
|2'
|-
|7
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|56
|-
|8
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|4
|-
|9
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|10
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|11
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|12
|PL0602
|VINYL EDGING
|
|''8' each for Item 3 (Not shown)''
|16'
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Used on units shipped prior to October, 2012. See Current BE-DS Dashboard in the Guarding Section for units shipped after October 2012.''
|-
| colspan="6" |''†† 43714016-2 valid for units shipped prior to December 2022.''
''41217014-2 valid for units shipped December 2022 to present.''
|}

==== <big>''[Current] BE-DS Dashboard Guarding''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-DS Current Dashboard.png|alt=BE-DS Current Dashboard|frameless|530x530px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43717123-2
|FRAME-DASHBOARD
|
|
|1
|-
|2
|43718017
|PLATE-DASHBOARD
|
|
|1
|-
|3
|HW0060
|NUT-CLIP-#10-24
|
|
|10
|-
|4
|SS0114
|BHSCS-#10-24 X 1/2" SST
|
|
|10
|-
|5
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|''Not shown''
|10
|}

==== ''BE-DS Inner Carriage Guards (Helical Actuator)'' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-DS-Helical Actuator Equipped Units Inner Guards.png|alt=BE-DS-Helical Actuator Units Inner Guards|frameless|526x526px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="2" |1
|43714016-2
|GUARD-FRONT-OPERATOR CONSOLE
|
|''† Without Cylinder Notch''
|1
|-
|41217014-2
|GUARD-FRONT-OPERATOR CONSOLE
|
|''† With Cylinder Notch''
|1
|-
|2
|43717016-2
|GUARD-INNER-FRAME
|
|
|2
|-
| rowspan="2" |3
|43017081-2
|GUARD-SIDE-ARM CARRIER SHAFT
|
|
|2
|-
|44517003-2
|GUARD-SIDE-ARM CARRIER SHAFT
|
|''†† Single Compartment Units Only''
|1
|-
|4
|43017080-2
|BRACKET-SIDE GUARD MOUNTING
|
|
|2
|-
|5
|43017082-3
|MOUNT-CHAIN GUARD-LEAD SCREW
|
|
|1
|-
|6
|43017082-4
|MOUNT-CHAIN GUARD-LEAD SCREW
|
|
|1
|-
|7
|43017083-2
|GUARD-CHAIN-LEAD SCREW
|
|
|1
|-
|8
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
| rowspan="2" |9
|43714015-2
|KICK PLATE-OPERATOR CONSOLE
|
|''35.5" tall''
|1
|-
|43717115-2
|KICK PLATE-OPERATOR CONSOLE
|
|''29" tall''
|1
|-
|10
|HW0103
|WASHER-LOCK-1/4"
|
|
|8
|-
|11
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|8
|-
|12
|HW0347
|BOLT-BHSCS-1/4-20 X 3/8"
|
|
|4
|-
|13
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|28
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† 43714016-2 valid for units shipped prior to December 2022.''
''41217014-2 43714016-2 valid for units shipped December 2022 to present.''
|-
| colspan="6" |''†† Single Compartment Guard replaces standard, Far Side Arm Carrier Shaft Guard.''
|}

==== <big>''BE-DS Operator Platform Guarding''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-DS Operator Platform.png|alt=BE-DS Operator Platform|frameless|587x587px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43715018
|PANEL-FLOOR
|
|''With reservoir access panel''
|1
|-
|2
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|8
|-
|3
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|8
|-
|4
|HW0103
|WASHER-LOCK-1/4"
|
|
|8
|-
|5
|HW0002
|NUT-HEX-1/4-20
|
|
|8
|-
|6
|43717022
|GRILL-HYDRAULIC COMPONENT
|
|
|1
|-
|7
|HW0403
|BOLT-HHCS-3/8-16 X 1 1/4"
|
|
|2
|-
|8
|HW0107
|WASHER-LOCK-3/8"
|
|
|2
|-
|9
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|2
|-
|10
|43706001
|MAT-ANTI FATIGUE
|
|''Not shown''
|1
|-
|11
|PL0602
|VINYL EDGING
|
|''For Item 6 (Not shown)''
|13'
|}

=== <big>Labels & Placards</big> ===

==== '''<big>''BE-SL Labels''</big>''' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL Labels.png|alt=BE-SL Labels|frameless|585x585px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|00196616
|LABEL-"NO RIDERS ALLOWED"
|
|
|1
|-
|2
|00196210
|LABEL-WARNING-"OPERATION BY AUTHORIZED PERSONNEL ONLY"
|
|
|1
|-
|3
|43696001
|PLACARD-OFF / ON
|
|
|1
|-
|4
|43096018
|PLACARD-RACK LEVEL ASSIST
|
|''† If Equipped''
|1
|-
|5
|43096014
|PLACARD-DRIVE / RAISE-LOWER / ARM ROTATION
|
|
|1
|-
|6
|43096010
|PLACARD-HORN
|
|''†'' ''If Equipped''
|1
|-
| rowspan="2" |7
|43096012
|PLACARD-VACUUM OFF / ON
|
|''Vacuum Units Only''
|1
|-
|43096011
|PLACARD-MAGNET OFF / ON
|
|''Magnet Units Only (Not shown)''
|1
|-
|8
|43096017
|PLACARD-POWERED ROLLER CUTOUT OVERRIDE
|
|''†'' ''If Equipped''
|1
|-
|9
|43096013
|PLACARD-POWERED ROLLERS / ARM TRAVERSE
|
|
|1
|-
|10
|00196004
|LABEL-CAUTION-"WATCH FOR BATTERY AND CHARGER CABLES IN TRAVEL PATH"
|
|
|1
|-
|11
|00196622
|LABEL-LIFT POINT
|
|''(2) Each end''
|4
|-
|12
|00196700
|DECAL-BHS-24"
|
|''Far End (Not shown)''
|2
|-
| rowspan="2" |13
|00196630
|LABEL-NOTICE-HYD. OIL SPEC. (AW 68)
|
|''†† See Notes''
|1
|-
|00196645
|LABEL-NOTICE-HYD. OIL SPEC. (AW 32)
|
|''††'' ''See Notes''
|1
|-
|14
|43096008
|PLACARD-"REPLACE WITH 10 AMP FUSE ONLY"
|
|''On transformer''
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Rack Level Assist (LAI), Horn and Powered Roller Cutout (PRC) are optional features. Not all units are equipped with these options.''
|-
| colspan="6" |''†† Most units shipped prior to December 2014 require AW 68 Hydraulic Oil. Some units shipped prior to December 2014 shipped with AW 32 for low temperature applications.''
|}

==== '''<big>''BE-DS Labels''</big>''' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-DS Labels.png|alt=BE-DS Labels|frameless|728x728px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|00196616
|LABEL-"NO RIDERS ALLOWED"
|
|
|1
|-
|2
|00196210
|LABEL-WARNING-"OPERATION BY AUTHORIZED PERSONNEL ONLY"
|
|
|1
|-
|3
|43696001
|PLACARD-OFF / ON
|
|
|1
|-
|4
|43096018
|PLACARD-RACK LEVEL ASSIST
|
|''†'' ''If Equipped''
|1
|-
|5
|43096014
|PLACARD-DRIVE / RAISE-LOWER / ARM ROTATION
|
|
|1
|-
|6
|43096010
|PLACARD-HORN
|
|''†'' ''If Equipped''
|1
|-
| rowspan="2" |7
|43096012
|PLACARD-VACUUM OFF / ON
|
|''Vacuum Units Only''
|1
|-
|43096011
|PLACARD-MAGNET OFF / ON
|
|''Magnet Units Only (Not shown)''
|1
|-
|8
|43096017
|PLACARD-POWERED ROLLER CUTOUT OVERRIDE
|
|''†'' ''If Equipped''
|1
|-
|9
|43096013
|PLACARD-POWERED ROLLERS / ARM TRAVERSE
|
|
|1
|-
|10
|00196004
|LABEL-CAUTION-"WATCH FOR BATTERY AND CHARGER CABLES IN TRAVEL PATH"
|
|
|1
|-
|11
|00196622
|LABEL-LIFT POINT
|
|''(2) Each end''
|4
|-
|12
|00196700
|DECAL-BHS-24"
|
|''Far End (Not shown)''
|2
|-
| rowspan="2" |13
|00196630
|LABEL-NOTICE-HYD. OIL SPEC. (AW 68)
|
|''†† See Notes''
|1
|-
|00196645
|LABEL-NOTICE-HYD. OIL SPEC. (AW 32)
|
|''†† See Notes''
|1
|-
|14
|43096008
|PLACARD-"REPLACE WITH 10 AMP FUSE ONLY"
|
|''On transformer''
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Rack Level Assist (LAI), Horn and Powered Roller Cutout (PRC) are optional features. Not all units are equipped with these options.''
|-
| colspan="6" |''†† Most units shipped prior to December 2014 require AW 68 Hydraulic Oil. Some units shipped prior to December 2014 shipped with AW 32 for low temperature applications.''
|}

==== '''<big>''Extractor Arm Labels''</big>''' ====
[[File:IOP-400 BE-SL&DS (10-23) Labels and Placards Parts.png|alt=Labels and Placards Parts|frameless|700x700px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|00196633
|LABEL-NOTICE-"IN LINE VACUUM FILTER..."
|
|''(1) per side (Vacuum Units Only)''
|2
|-
|2
|SM-1197
|LABEL-ARM POSITION ARROW
|
|
|2
|-
|3
|00196609
|LABEL-NOTICE-"ARM MUST BE POSITIONED BETWEEN ARROWS..."
|
|
|1
|-
|4
|00196602
|LABEL-NOTICE-"LUBRICATION POINTS ON UNDERSIDE"
|
|
|2
|-
|5
|00196218
|LABEL-WARNING-"ELECTRICAL VOLTAGE HAZARD"
|
|''Magnet Units Only''
|1
|-
|6
|00196238
|LABEL-WARNING-"STRONG MAGNETIC

FIELD/DO NOT USE WITH PACEMAKER"
|
|''† Magnet Units Only''
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Pacemaker Warning Label takes place of discontinued, Triangular Magnetic Field Label.''
|}

== <big>Extractor Arm</big> ==
{| class="wikitable"
!SYMBOL
!DESCRIPTION / NOTICE
!ACTUATOR DIAGRAM
|-
|[[File:IOP-400 BE-SL&DS (10-23) Rotary Actuator Symbol.png|alt=Rotary Actuator Symbol|frameless]]
|
=== '''<big>Rotary Actuator Symbol</big>''' ===
Battery Extractors shipped prior to May 2020 are equipped with Rotary Actuator Extractor Arms.
Parts Diagrams Specific to the Rotary Actuator design are indicated with the symbol.
|[[File:IOP-400 BE-SL&DS (10-23) Rotary Actuator Extractor Arm.png|alt=BE-SL & BE-DS Rotary Actuator |frameless]]
|-
|[[File:IOP-400 BE-SL&DS (10-23) Helical Actuator Symbol.png|alt=Helical Actuator Symbol|frameless]]
|
=== <big>'''Helical Actuator Symbol'''</big> ===
Battery Extractors shipped from May 2020 to Present are equipped with Helical Actuator Extractor Arms.
Parts Diagrams Specific to the Rotary Actuator design are indicated with the Helical Actuator Symbol.
|[[File:IOP-400 BE-SL&DS (10-23) Helical Actuator Extractor Arm.png|alt=BE-SL & BE-DS Helical Actuator |frameless]]
|}

=== <big>Vacuum Components & Swing Arms</big> ===

==== ''<big>Vacuum Arms (Rotary Actuator)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Vacuum Arm.png|alt=Vacuum Arm|frameless|648x648px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="2" |1
|N/A
|ARM-PUSH/PULL-30"
|
|''† Discontinued''
|1
|-
|N/A
|ARM-PUSH/PULL-36"
|
|''† Discontinued''
|1
|-
|2
|HW0509
|BOLT-HHCS-1/2-13 X 4 1/2"
|
|
|3
|-
|3
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|6
|-
|4
|HW0110
|WASHER-LOCK-1/2"
|
|
|3
|-
|5
|HW0007
|NUT-HEX-1/2-13
|
|
|3
|-
|6
|P0505
|BUSHING-RED-#6 NPT X #4 FNPT-BRASS
|
|
|2
|-
|7
|P0402
|HOSE BARB-1/4 X #4 MNPT-BRASS
|
|
|2
|-
|8
|HW0428
|STUD-VACUUM-3/8-16 X 5"
|HW-KIT-2
|
|8
|-
|9
|HW0108
|WASHER-FLAT-3/8"-SAE
|HW-KIT-2
|
|40
|-
|10
|HW1001
|SPRING-3/8"
|HW-KIT-2
|
|24
|-
|11
|HW0006
|NUT-NILN-3/8-16
|HW-KIT-2
|
|8
|-
|12
|HW0424
|NUT-JAM-3/8-16
|HW-KIT-2
|
|8
|-
|REF
|43052006
|ADJUSTABLE PUSH/PULL ARM
|
|''Includes Items 13 through 17''
|1
|-
|13
|43057034
|ARM BASE
|
|
|1
|-
|14
|43055008
|VACUUM CUP MOUNT
|
|
|2
|-
|15
|HW0523
|BOLT-HHCS-1/2-13 X 4"
|
|
|2
|-
|16
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|4
|-
|17
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† One-piece Arms no longer available. Must replace with Adjustable Arm.''
|}

==== <big>''Vacuum Cups''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Vacuum Cups.png|alt=Vacuum Cups|frameless|619x619px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="4" |A/R
|00162004
|VACUUM CUP-10" 3-PC (STANDARD)
|
|''† Includes Items 1 through 4''
| rowspan="4" |A/R
|-
|00162003
|VACUUM CUP-12" 3-PC (STANDARD)
|
|''† Includes Items 4 through 7''
|-
|00162007
|VACUUM CUP-10" 3-PC, REINFORCED
|
|''Includes Items 1,3,4 & 8''
|-
|00162005
|VACUUM CUP-12" 3-PC, REINFORCED
|
|''Includes Items 4,5,7 & 9''
|-
|1
|00164006
|CASTING-10" VACUUM CUP
|
| rowspan="3" |''10" cup only''
|1
|-
|2
|00164004
|SEAL-RUBBER-10"
|
|1
|-
|3
|00165002
|PLATE-FRONT-10"
|
|1
|-
|4
|HW0311
|BOLT-FHSCS-1/4-20 X 3/4"
|
|
|8
|-
|5
|00166001
|CASTING-12" VACUUM CUP
|
| rowspan="3" |''12" cup only''
|1
|-
|6
|00164001
|SEAL-RUBBER-12"
|
|1
|-
|7
|00165001
|PLATE-FRONT-12"
|
|1
|-
|8
|00164007
|SEAL-RUBBER-10"-REINFORCED
|
|
|A/R
|-
|9
|00167003
|SEAL-RUBBER-12"-REINFORCED
|
|
|A/R
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† 10" and 12" 1-Piece Cups no longer available. Must replace with 3-Piece Cup. Verify required cup size prior to ordering.''
|}

==== <big>''Swing Arms (Rotary Actuator)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Swing Arm Rotary Actuator.png|alt=Swing Arms (Rotary Actuator)|frameless|525x525px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="3" |1
|45055001
|TIE PLATE-SWING ARM
|
|''BE-24-2''
|1
|-
|45255001
|TIE PLATE-SWING ARM
|
|''BE-36-2 (Not shown)''
|1
|-
|45355001
|TIE PLATE-SWING ARM
|
|''BE-42-2 (Not shown)''
|1
|-
|2
|43055004
|SWING ARM-RHS
|†
|''Not sold individually''
|1
|-
|3
|43055002
|SWING ARM-LHS
|†
|''Not sold individually''
|1
|-
|4
|HW0603
|BOLT-FHSCS-5/8-11 X 2"
|
|
|4
|-
|5
|HW0113
|WASHER-LOCK-5/8"
|
|
|4
|-
|6
|HW0010
|NUT-JAM-5/8-11
|
|
|4
|-
|7
|PT0413
|COLLAR-SHAFT-3"
|80252001
|
|2
|-
|8
|43027001
|SHAFT-ROTARY ACTUATOR
|80252001
|
|1
|-
|9
|HW1013
|KEY-3/8" X 12"
|80252001
|
|1
|-
|10
|PT0419
|BEARING-SAE 841-2" I.D., 3" OD, 1/8" THICK
|80252001
|
|3
|-
|11
|43052005
|CAP-BEARING
|
|''Includes bearing''
|2
|-
|12
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|6
|-
|13
|HW0103
|WASHER-LOCK-1/4"
|
|
|6
|-
|14
|43057014
|STANDOFF-WIRE
|
|
|1
|-
|15
|HW0312
|SCREW-SHSS-1/4-20 X 1"-CUP POINT
|
|
|1
|-
|16
|43057003
|CUSHION-SWING ARM
|
|
|2
|-
|17
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|4
|-
| rowspan="2" |18
|43055001
|STOP-SWING ARM
|
|
|2
|-
|44555001
|STOP-SWING ARM
|
|''BE-42-1 only''
|1
|-
|19
|HW0403
|BOLT-HHCS-3/8-16 X 1 1/4"
|
|
|4
|-
|20
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|21
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|4
|-
|22
|H1565
|ADAPTER-45 DEG-#6 JICM X #4 NPTM
|
|
|2
|-
|23
|H1600
|ADAPTER-90 DEG-#6 JICM X #8 SAEM
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |† ''Included in multiple kits.''
|}
[[File:IOP-400 BE-SL&DS (10-23) Swing Arm Stop Rotary.png|alt= BE-SL&DS Swing Arm Stop Rotary (Rotary Actuator)|frameless|534x534px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|44555001
|STOP-SWING ARM
|
|
|1
|-
|2
|43057003
|CUSHION-SWING ARM
|
|
|1
|-
|3
|43057008
|SPACER-SWING ARM STOP
|
|
|1
|-
|4
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|2
|-
|5
|HW0403
|BOLT-HHCS-3/8-16 X 1 1/4"
|
|
|4
|-
|6
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|}

==== ''<big>Vacuum Pump (Rotary Actuator)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Vacuum Pump (Rotary Actuator).png|alt=BE-SL&DS Vacuum Pump (Rotary Actuator)|frameless|532x532px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|P0005
|PUMP-VACUUM
|
|
|1
|-
|2
|P0208
|FILTER-HI FLOW
|
|
|3
|-
|3
|P0503
|NIPPLE-#4 NPT-BRASS
|
|
|3
|-
|4
|P0502
|TEE-#4 FNPT-BRASS
|
|
|1
|-
|5
|P0506
|ELBOW-STR-90 DEG-#4 NPT-BRASS
|
|
|4
|-
|6
|P0402
|HOSE BARB-1/4 X #4 NPTM-BRASS
|
|
|6
|-
|7
|P0207
|VALVE-VACUUM RELEASE
|
|
|2
|-
|8
|P0302
|HOSE-VACUUM-1/4" I.D.
|
|''Two 6" pieces''
|1'
|-
|9
|P0302
|HOSE-VACUUM-1/4" I.D.
|
|''Short Arm side''
|1'
|-
|10
|P0302
|HOSE-VACUUM-1/4" I.D.
|
|''Long Arm side''
|2'
|-
|11
|E0611
|JUNCTION BOX-4" X 2" X 2"
|
|
|1
|-
|12
|E0612
|COVER-JUNCTION BOX
|
|
|1
|-
|13
|HW0212
|SCREW-RHMS-#10-24 X 1/2"
|
|
|2
|-
|14
|E0624
|CONNECTOR-1/2"
|
|
|1
|-
|15
|E0608-1
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .450" to .560"''
|1
|-
|15a
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|''Not shown''
|2
|-
| rowspan="2" |16
|E0501
|CORD-14-4 SW/SOW
|
|''Withtout Ground Connection in Arm''
| rowspan="2" |15'
|-
|E0514
|CORD-16-5 SW/SOW
|
|
|-
|17
|43057014
|STANDOFF-CABLE
|
|
|1
|-
|18
|HW0206
|SCREW-RHMS-#10-32 X 3/4"
|
|
|4
|-
|19
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|1
|-
|20
|43057021
|PLATE-STIFFENER
|†
|
|2
|-
|21
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|†
|
|12
|-
|22
|HW0107
|WASHER-LOCK-3/8"
|†
|
|12
|-
|23
|HW0005
|NUT-HEX-3/8-16
|†
|
|12
|-
|24
|HW0108
|WASHER-FLAT-3/8"-SAE
|†
|''Not shown''
|24
|-
|25
|P0111
|FILTER-VACUUM-INLINE
|
|''Not shown''
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |† ''Included in multiple kits.''
|}

=== <big>Rotary Actuator</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Rotary-Actuator.png|alt=BE-SL & BE-DS Rotary Actuator|frameless|523x523px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43046001
|ROTARY ACTUATOR
|
|
|1
|-
|2
|80000002
|ROTARY ACTUATOR BASE ASSEMBLY
|
|''Without Actuator''
|1
|-
|2A
|N/A
|VERTICAL CARRIER PLATE-OUTER
|
|''Included with 80000002''
|2
|-
|2B
|N/A
|VERTICAL CARRIER PLATE-INNER
|
|''Included with 80000002''
|1
|-
|2C
|N/A
|CARRIER BASE PLATE
|
|''Included with 80000002''
|1
|-
|3
|HW1070
|PIN-PULL DOWEL-5/8" X 1 1/2"
|
|
|2
|-
|4
|HW0508
|BOLT-SHCS-1/2-13 X 3/4"
|
|
|3
|-
|5
|HW1045
|PIN-PULL DOWEL-3/8" X 1 1/2"
|
|''Included with 80000002''
|6
|-
|6
|HW0412
|BOLT-SHCS-3/8-16 X 1 1/4"
|
|''Included with 80000002''
|12
|-
|7
|H0010
|FITTING-BULKHEAD-3/4-16 X #4 FNPT
|
|
|4
|-
|8
|H1579
|ADAPTER-90 DEG-#6 JICM X #4 NPTM
|
|
|2
|}

=== <big>Carrier Shafts & Bearings ''(Rotary Actuator)''</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Carrier Shafts Rotary Actuator.png|alt=BE-SL&DS Carrier Shafts (Rotary Actuator)|frameless|522x522px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43057045
|CARRIER SHAFT-EXTRACTOR ARM
|
|''† See notes''
|2
|-
|2
|43054007
|BEARING-EXTRACTOR ARM CARRIER
|80252002
|''†† See notes''
|4
|-
|3
|HW0412
|BOLT-SHCS-3/8-16 X 1 1/4"
|80252002
|
|16
|-
|4
|PT0413
|COLLAR-SHAFT-3"
|
|
|4
|-
|5
|PT0624
|FITTING-ZERK
|80252002
|''Not shown''
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† See Extended Reach End Plate section (2.6.8) for Extended Reach equipped units.''
|-
| colspan="6" |''†† See [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Carrier_Shafts_&_Bearings_(Helical_Actuator) Carrier Shafts & Bearings (Helical Actuator)] section for Helical Actuator equipped units''
|}

=== <big>Drive Screw Components ''(Rotary Actuator)''</big> ===

==== ''<big>Drive Nut Assembly (Rotary Actuator)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Drive Nut Assembly Rotary Actuator.png|alt= BE-SL&DS Drive Nut Assembly Rotary Actuator|frameless|537x537px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43054006
|DRIVE NUT ASSEMBLY
|80252003
|''†'' ''See notes''
|1
|-
|2
|HW0426
|BOLT-SHCS-3/8-16 X 5 1/2"
|80252003
|''††'' ''See notes''
|4
|-
|3
|HW0108
|WASHER-FLAT-3/8"-SAE
|80252003
|''††'' ''See notes''
|4
|-
|4
|HW0006
|NUT-NILN-3/8-16
|80252003
|''††'' ''See notes''
|4
|-
|5
|PT0624
|FITTING-ZERK
|80252003
|
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† See [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Drive_Screw_Components_(Helical_Actuator) Drive Screw Components (Helical Actuator)] section for Helical Actuator equipped units.''
|-
| colspan="6" |''†† It is recommended to replace mounting hardware when replacing Drive Nut Assembly.''
|}

==== ''<big>Drive Screw</big>'' ====

===== ''[Current] Drive Screw Assembly (Frame #'s 374 to Present)'' =====
[[File:IOP-400 BE-SL&DS (10-23) Drive Screw Rotary Current.png|alt=Current BE-SL & BE-DS Drive Screw (Rotary Actuator)|frameless|531x531px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43024001
|SCREW-LINEAR DRIVE
|
|
|1
|-
|2
|PT0119
|SPROCKET-50B15 X 1 3/16"
|
|
|1
|-
|3
|43097004
|KEY-1/4 X 7/8"
|
|
|1
|-
|4
|00158001-15
|CHAIN-ROLLER-#50
|
|
|1
|-
|5
|PT0102
|LINK-CONNECTING-#50
|
|
|1
|-
|6
|PT0406
|FLANGE BEARING-4 BOLT-1 3/16"
|
|''Alloy casting''
|2
|-
|7
|HW0503
|BOLT-HHCS-1/2-13 X 1 1/2"
|
|
|8
|-
|8
|HW0110
|WASHER-LOCK-1/2"
|
|
|8
|-
|9
|PT0107
|SPROCKET-50B15 X 1"
|
|
|1
|-
|10
|HC0121
|MOTOR-HYDRAULIC-100CC
|
|''SAE 2-Bolt mount''
|1
|-
|11
|H1605
|ADAPTER-90 DEG-#6 JICM X #10 SAEM
|
|
|2
|-
|12
|HW1071
|KEY-WOODRUFF-#808 STD
|
|''Supplied with Item 10''
|A/R
|-
|13
|HW0403
|BOLT-HHCS-3/8-16 X 1 1/4"
|
|
|6
|-
|14
|HW0107
|WASHER-LOCK-3/8"
|
|
|6
|-
|15
|43017007
|PLATE-MOUNTING-SCREW DRIVE MOTOR
|
|
|1
|-
|16
|43057019
|PLATE-COVER
|
|
|2
|-
|17
|HW0415
|BOLT-SHCS-3/8-16 X 3/4"
|
|
|8
|}
{| class="wikitable"
! colspan="6" |ITEMS BELOW ARE REQUIRED FOR REPLACING THE LINEAR DRIVE

SCREW ON UNITS WITH FRAME #'S OF 373 AND EARLIER
|-
! colspan="6" |LINEAR DRIVE SCREW UPDATE KIT
|-
|REF
|80252011
|UPGRADE KIT
|
|
|1
|-
|1
|43024001
|SCREW-LINEAR DRIVE
|
|
|1
|-
|2
|PT0119
|SPROCKET-50B15 X 1 3/16"
|
|
|1
|-
|3
|43097004
|KEY-1/4 X 7/8"
|
|
|1
|-
|6
|PT0406
|FLANGE BEARING-4 BOLT-1 3/16"
|
|''Alloy casting''
|2
|-
|7
|HW0503
|BOLT-HHCS-1/2-13 X 1 1/2"
|
|
|8
|-
|8
|HW0110
|WASHER-LOCK-1/2"
|
|
|8
|-
|16
|43057019
|PLATE-COVER
|
|
|2
|-
|18
|43057022
|SHIM-18GA
|
|''May not be required (Not shown)''
|2
|-
|19
|43057018
|TEMPLATE-BEARING MOUNT PATTERN
|
|''Not shown''
|1
|-
|20
|80000015
|INSTRUCTION DETAIL
|
|''Not shown''
|REF
|-
|21
|43057020
|SPACER PLATE
|
|''Not shown''
|2
|}

===== ''[Discontinued] Drive Screw Assembly (Frame #'s 373 and Earlier)'' =====
[[File:IOP-400 BE-SL&DS (10-23) Drive Screw (Rotary Actuator) Discontinued.png|alt=Discontinued BE-SL & BE-DS Drive Screw (Rotary Actuator)|frameless|532x532px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|N/A
|SCREW-LINEAR DRIVE (DISCONTINUED)
|
|''See 80252011 Upgrade Kit''
|1
|-
|2
|PT0118
|SPROCKET-50B12 X 1 3/16"
|
|
|1
|-
|3
|43097004
|KEY-1/4" X 7/8"
|
|
|1
|-
|4
|00158001-15
|CHAIN-ROLLER-#50
|
|
|1
|-
|5
|PT0102
|LINK-CONNECTING-#50
|
|
|1
|-
|6
|43057016
|BLOCK-BEARING RETAINER
|
|
|2
|-
|6a
|PT0414
|RACE-TAPERED ROLLER BEARING
|
|''Included with 43057016''
|2
|-
|7
|PT0623
|SEAL-GREASE
|
|
|2
|-
|8
|HW0416
|BOLT-SHCS-3/8-16 X 1"
|
|
|8
|-
|9
|PT0415
|BEARING-TAPERED ROLLER
|
|
|2
|-
|10
|HW1050
|NUT-LOCK
|
|
|4
|-
|11
|43057017
|PLATE-COVER
|
|
|2
|-
|12
|HW0415
|BOLT-SHCS-3/8-16 X 3/4"
|
|
|8
|-
|13
|PT0624
|FITTING-ZERK
|
|
|2
|}

=== <big>Hose Carrier Plate</big> ===
d[[File:IOP-400 BE-SL&DS (10-23) Hose Carrier.png|alt=BE-SL&DS Hose Carrier|frameless|557x557px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43017013
|PLATE-HOSE CARRIER
|
|
|1
|-
|2
|PT0618
|BRACKET-FIXED END
|
|
|1
|-
|3
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
|4
|PT0617
|HOSE CARRIER
|
|''20 links required''
|3'
|-
|5
|PT0619
|BRACKET-MOVING END
|
|
|1
|-
|6
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|2
|-
|7
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|8
|HW0403
|BOLT-HHCS-3/8-16 X 1 1/4"
|
|
|4
|-
|9
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|8
|-
|10
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|11
|HW0005
|NUT-HEX-3/8-16
|
|
|4
|}

=== <big>Magnet Components ''(Rotary Actuator)''</big> ===

==== ''<big>[Discontinued] Magnet Arm Configuration (Rotary Actuator)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Magnet Extraction Prior to Nov 2014 (Rotary Actuator).png|alt= BE-SL & BE-DS Magnet Extraction Prior to Nov 2014 (Rotary Actuator)|frameless|563x563px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41257014
|TIE PLATE-SWING ARM
|
|''All units''
|1
|-
|<nowiki>-</nowiki>
|41655008
|EXTENSION-ARM
|
|''BE-36-2 only (Not shown)''
|1
|-
|<nowiki>-</nowiki>
|43455001
|EXTENSION-ARM
|
|''BE-42-2 only (Not shown)''
|1
|-
|2
|HW0603
|BOLT-FHSCS-5/8-11 X 2"
|
|
|4
|-
|3
|HW0113
|WASHER-LOCK-5/8"
|
|
|4
|-
|4
|HW0010
|NUT-JAM-5/8-11
|
|
|4
|-
|5
|41655001
|CARRIER TUBE-MAGNET SWING SHAFT
|
|
|1
|-
|6
|HW0504
|BOLT-HHCS-1/2-13 X 2"
|
|
|6
|-
|7
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|6
|-
|8
|HW0110
|WASHER-LOCK-1/2"
|
|
|6
|-
|9
|HW0007
|NUT-HEX-1/2-13
|
|
|6
|-
|10
|41657006
|SHAFT-MAGNET SWING
|
|
|1
|-
|11
|41698001
|KEY-3/8" X 7/16"
|
|
|2
|-
|12
|N/A
|STOP-MAGNET SWING
|
|''† Discontinued''
|1
|-
|13
|PT0430
|FLANGE BEARING-4 BOLT-1 1/2"
|
|
|2
|-
|14
|HW0513
|BOLT-HHCS-1/2-13 X 2 1/4"
|
|
|8
|-
|15
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|16
|-
|16
|HW0110
|WASHER-LOCK-1/2"
|
|
|8
|-
|17
|HW0007
|NUT-HEX-1/2-13
|
|
|8
|-
|18
|41655002
|PLATE-MAGNET MOUNTING
|
|
|2
|-
|19
|41257015
|BLOCK-TIGHTENER
|
|''2-Piece Item''
|1
|-
|20
|41257016
|BLOCK-FIXED
|
|''2-Piece Item''
|1
|-
|21
|HW0423
|BOLT-SHCS-3/8-16 X 3 1/2"
|
|
|4
|-
|22
|HW0006
|NUT-NILN-3/8-16
|
|
|4
|-
|23
|HW0806
|SET SCREW-3/8-16 X 2"
|
|''Replaces Swivel Head''
|4
|-
|24
|HW0424
|NUT-JAM-3/8-16
|
|
|4
|-
|25
|41657017
|INSULATOR-MAGNET MOUNT
|
|
|2
|-
|26
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|8
|-
|27
|41657008
|PAD-MAGNET SLIDE
|
|
|2
|-
|28
|HW0314
|BOLT-FHSCS-1/4-20 X 1/2"
|
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Refer to [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Magnet_Pivot_Stop_(Rotary_Actuator) Magnet Pivot Stop (Rotary Actuator)] section for replacement/upgrade parts.''
|}

==== <big>''Magnet Pivot Stop (Rotary Actuator)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Magnet Pivot Stop (Rotary Actuator).png|alt=BE-SL & BE-DS Magnet Pivot Stop (Rotary Actuator)|frameless|551x551px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|80252012
|MAGNET SWING STOP KIT
|
|''Includes Items 1 through 6''
|A/R
|-
|1
|43057029
|PLATE-STOP
|
|
|1
|-
|2
|43058003
|SLEEVE-STOP
|
|
|2
|-
|3
|43057030
|SUPPORT-CABLE
|
|
|2
|-
|4
|PL0501
|GROMMET-1/2"
|
|
|2
|-
|5
|HW0509
|BOLT-HHCS-1/2-13 X 4 1/2"
|
|
|2
|-
|6
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|-
|7
|44557003
|PLATE-STOP
|
|''† Single compartment units only''
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† For units equipped with Pivot Shaft. See [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Current_Magnet_Arm_Configuration_(Rotary_Actuator) Current Magnet Arm Configuration (Rotary Actuator)] section for units with independent Magnet Pivot Bearings.''
|}

==== ''<big>[Current] Magnet Arm Configuration (Rotary Actuator — November 2014 to Present)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Current Magnet Arm Configuration (Rotary Actuator).png|alt=BE-SL & BE-DS Current Magnet Arm Configuration (Rotary Actuator)|frameless|547x547px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|N/A
|MAGNET PUSH/PULL ARM
|
|''†'' ''See notes''
|1
|-
|2
|43055010
|MAGNET MOUNT
|
|
|2
|-
|3
|PT0470
|BEARING-MAGNET PIVOT
|
|
|2
|-
|4
|HW0525
|BOLT-CARRIAGE-1/2-13 X 1 1/2"
|
|
|12
|-
|5
|HW0524
|BOLT-CARRIAGE-1/2-13 X 2"
|
|''††'' ''Stop Plate location''
|4
|-
|6
|HW0110
|WASHER-LOCK-1/2"
|
|
|16
|-
|7
|HW0007
|NUT-HEX-1/2-13
|
|
|16
|-
|8
|43058009
|PLATE-ROTATION STOP
|
|
|2
|-
|9
|43058003
|SLEEVE-STOP
|
|
|2
|-
|10
|43058010
|SUPPORT-CABLE
|
|
|2
|-
|11
|PL0501
|GROMMET-1/2"
|
|
|2
|-
|12
|HW0523
|BOLT-HHCS-1/2-13 X 4"
|
|
|2
|-
|13
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|-
|14
|43057037
|INSULATOR-BOTTOM
|
|
|2
|-
|15
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|8
|-
|16
|41657008
|SLIDE-MAGNET
|
|
|2
|-
|17
|HW0314
|BOLT-FHSCS-1/4-20 X 1/2"
|
|
|4
|-
|18
|44558001
|PLATE-ROTATION STOP
|
|''†† Single compartment units only''
|2
|-
|REF
|43052014
|ADJUSTABLE PUSH-PULL ARM
|
|''Includes Items 19 through 23''
|A/R
|-
|19
|43055018
|ARM BASE
|
|
|1
|-
|20
|43055019
|MAGNET MOUNT
|
|
|2
|-
|21
|HW0523
|BOLT-HHCS-1/2-13 X 4"
|
|
|2
|-
|22
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|4
|-
|23
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† 1-Piece Arm no longer available. Must be replaced with Adjustable Arm.''

''†† Single Compartment Stop Plates require (1) additional 2" Long Carriage Bolt each.''
|}

==== <big>''Magnet Mounting Hardware (Rotary Actuator)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Magnet Mounting Hardware (Rotary Actuator).png|alt=BE-SL & BE-DS Magnet Mounting Hardware (Rotary Actuator)|frameless|570x570px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43032009
|MAGNET ASSEMBLY
|
|''Includes Items 1 through 12''
|A/R
|-
|1
|N/A
|ELECTROMAGNET-95VDC
|
|
|2
|-
|2
|E0314
|SENSOR-PROXIMITY-30MM
|
|
|2
|-
|3
|N/A
|GASKET-REAR
|
|''Discontinued (Not Used)''
|2
|-
|4
|41657002
|COVER-PROXIMITY SENSOR HOUSING
|
|''Rear''
|2
|-
|5
|HW1065
|SCREW-SHCS-#6-32 X 3/8"
|
|
|8
|-
|6
|HW1066
|WASHER-LOCK-#6
|
|
|8
|-
|7
|E0376
|INDICATOR LIGHT
|
|''†'' ''See notes''
|2
|-
|8
|E0335
|RECEPTACLE-5 PIN MALE
|
|''With 12" lead''
|2
|-
|9
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|2
|-
|10
|N/A
|GASKET-FRONT
|
|''Discontinued (Not Used)''
|2
|-
|11
|41657003
|COVER-PROXIMITY SENSOR HOUSING
|80252015
|''Front''
|2
|-
|12
|HW0138
|SCREW-FHSCS-#8-32 X 3/8"
|80252015
|
|8
|-
|13
|HW0433
|STUD-1/2-13 X 5"
|80252006
| rowspan="5" |''For units with Magnet Pivot Shaft only.''

''See [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Discontinued_Magnet_Arm_Configuration_(Rotary_Actuator) Discontinued Magnet Arm Configuration (Rotary Actuator)] section''

''(Units built prior to 11/01/14)''
|8
|-
|14
|HW0007
|NUT-HEX-1/2-13
|80252006
|8
|-
|15
|HW0112
|WASHER-FLAT-1/2"-SAE
|80252006
|40
|-
|16
|HW1002
|SPRING-1/2"
|80252006
|24
|-
|17
|HW0008
|NUT-NILN-1/2-13
|80252006
|8
|-
|18
|HW0514
|BOLT-HHCS-1/2-13 X 2 1/2"
|80252014
| rowspan="4" |''For units with Independent Pivot Bearing only.''

''See [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Current_Magnet_Arm_Configuration_(Rotary_Actuator) Current Magnet Arm Configuration (Rotary Actuator)] section''

''(Units built 11/01/14 to Present)''
|4
|-
|19
|HW1002
|SPRING-1/2"
|80252014
|4
|-
|20
|HW0112
|WASHER-FLAT-1/2"-SAE
|80252014
|8
|-
|21
|HW0007
|NUT-HEX-1/2-13
|80252014
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Extractors built or Replacement Magnets shipped prior to October 2021 used Multi-piece Indicator Lights with Replaceable Bulb and Lens and are no longer available.''

''Current Indicator Light is a 1-Piece LED assembly. Replacement of any Multi-Piece Component requires replacing entire assembly with current, 1-Piece Indicator Light.''
|}

==== ''<big>Magnet Cords (Rotary Actuator)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Magnet Cords (Rotary Actuator).png|alt=BE-SL & BE-DS Magnet Cords (Rotary Actuator)|frameless|568x568px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E1105
|JUNCTION BOX-4" X 2" X 2"
|
|''Weather Proof Box''
|1
|-
|2
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
|3
|E1106
|COVER-JUNCTION BOX
|
|''Weather Proof with Gasket''
|1
|-
|4
|E0333
|RECEPTACLE-9 PIN MALE
|
|''With 12" Lead''
|1
|-
|5
|E0608-1
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .450" to .560"''
|2
|-
|6
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|3
|-
|7
|E0334
|CORD-5 PIN FEMALE
|
|''With 36" Lead''
|2
|-
|8
|E0332
|CORD-9 PIN FEMALE-90 DEG
|
|''With 36" Lead''
|1
|-
|9
|PL0501
|GROMMET-1/2"
|
|
|1
|-
|10
|41657013-2
|PLATE-PANEL MOUNTING
|
|''With Single Cable Hole''
|1
|-
|11
|E0334-6
|CORD-5 PIN FEMALE
|
|''With 72" Lead''
|2
|-
|12
|43057038-2
|PLATE-PANEL MOUNTING
|
|''With Dual Cable Holes''
|1
|}

==== ''<big>Panel Mounting (Rotary Actuator)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Panel Mounting (Rotary Actuator).png|alt=BE-SL & BE-DS Panel Mounting (Rotary Actuator)|frameless|550x550px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43057021
|PLATE-STIFFENER
|
|
|1
|-
|2
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|12
|-
|3
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|''(Not shown)''
|24
|-
|4
|HW0107
|WASHER-LOCK-3/8"
|
|
|12
|-
|5
|HW0005
|NUT-HEX-3/8-16
|
|
|12
|-
|6
|41637001
|PANEL-COMPONENT MOUNTING
|
|
|1
|-
|7
|HW0325
|BOLT-5/16-18 X 1 3/4"-PAN HEAD
|
|
|4
|-
|8
|N/A
|INSULATOR-THREADED FEMALE
|
|''Discontinued''
|4
|-
|9
|HW0106
|WASHER-FLAT-5/16"-SAE
|
|
|8
|-
|10
|HW0326
|NUT-NILN-5/16-18
|
|
|8
|-
|11
|E1016
|FUSE HOLDER
|
|
|1
|-
|12
|HW0130
|SCREW-RHMS-#8-32 X 1/2"
|
|
|1
|-
|13
|HW0133
|WASHER-FLAT-#8-SAE
|
|
|1
|-
|14
|HW0132
|NUT-NILN-#8-32
|
|
|1
|-
|15
|E0325
|FUSE-7AMP-250VAC
|
|''FLM-7 or FNM-7''
|1
|-
|16
|PL0307
|INSULATOR-MALE STUD
|
|
|4
|}

==== ''<big>Magnet Extractor Electrical Panel (Rotary Actuator)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Electrical Panel (Rotary Actuator).png|alt=BE-SL & BE-DS Electrical Panel (Rotary Actuator)|frameless|565x565px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41637001
|PANEL-COMPONENT MOUNTING
|
|
|1
|-
|2
|41637002
|WIRE WAY
|
|
|2
|-
|3
|41637003
|WIRE WAY
|
|
|1
|-
|4
|41637004
|TRACK-TERMINAL BLOCK MOUNTING
|
|
|1
|-
|5
|41637005
|TRACK-TERMINAL BLOCK MOUNTING
|
|
|1
|-
|6
|HW0130
|SCREW-RHMS-#8-32 X 1/2"
|
|
|10
|-
|7
|HW0133
|WASHER-FLAT-#8-SAE
|
|
|10
|-
|8
|HW0132
|NUT-NILN-#8-32
|
|''(Not shown)''
|16
|-
|9
|E1020
|TERMINAL BLOCK
|
|
|12
|-
|10
|E1040
|END BARRIER
|
|
|2
|-
|11
|E1330
|END ANCHOR
|
|
|4
|-
|12
|E1009
|RECTIFIER-FULL WAVE BRIDGE
|
|
|2
|-
|13
|HW0135
|SCREW-RHMS-#8-32 X 3/4"
|
|
|2
|-
|14
|E1313
|SOCKET-RELAY-8 PIN
|
|
|2
|-
|15
|HW0139
|SCREW-RHMS-#8-32 X 1 1/4"
|
|
|4
|-
|16
|E0331
|RELAY-DPDT-110VAC
|
|''With Indicator Light''
|2
|}

==== <big>''Swing Arm Stop (Rotary Actuator)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Magnet Mount Stop Swing Arm (Rotary Actuator).png|alt=BE-SL & BE-DS Magnet Mount Stop Swing Arm (Rotary Actuator)|frameless|562x562px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43055007
|MOUNT-STOP-SWING ARM
|
|
|2
|-
| rowspan="2" |2
|43057024
|STOP-SWING ARM
|
|''BE-24''
|4
|-
|43057023
|STOP-SWING ARM
|
|''BE-36 & BE-42''
|4
|-
|3
|HW0304
|BOLT-HHCS-1/4-20 X 1 1/2"
|
|
|4
|-
|4
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|8
|-
|5
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|6
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|7
|HW0403
|BOLT-HHCS-3/8-16 X 1 1/4"
|
|
|4
|-
|8
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|9
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|4
|}

=== <big>Extended Reach Hydraulics ''(Rotary Actuator)''</big> ===

==== <big>''Vacuum Extended Reach (Rotary Actuator)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Vacuum Extended Reach (Rotary Actuator).png|alt= BE-SL&DS Vacuum Extended Reach (Rotary Actuator)|frameless|531x531px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41257014
|TIE PLATE-SWING ARM
|
|''All units''
|1
|-
|<nowiki>-</nowiki>
|41655008
|EXTENSION-ARM
|
|''BE-36-2 only (Not shown)''
|1
|-
|<nowiki>-</nowiki>
|43455001
|EXTENSION-ARM
|
|''BE-42-2 only (Not shown)''
|1
|-
|2
|HW0504
|BOLT-HHCS-1/2-13 X 2"
|
|
|6
|-
|3
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|6
|-
|4
|HW0110
|WASHER-LOCK-1/2"
|
|
|6
|-
|5
|HW0007
|NUT-HEX-1/2-13
|
|
|6
|-
|6
|P0301-1
|HOSE-COIL-VACUUM
|
|
|1
|-
|7
|41257035
|STANDOFF
|
|
|2
|-
|8
|HW1072
|RESTRAINT-HOSE
|
|
|2
|-
|9
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|2
|-
|10
|HW0103
|WASHER-LOCK-1/4'
|
|
|2
|-
|11
|HW0318
|BOLT-SHCS-1/4-20 X 1 1/2"
|
|
|2
|-
|12
|HW0302
|BOLT-HHCS-1/4-20 X 3/4"
|
|
|1
|-
|13
|HW0312
|SCREW-SHSS-1/4-20 X 1"-CUP POINT
|
|
|1
|}
[[File:IOP-400 BE-SL&DS (10-23) Vacuum Extended Reach 2 (Rotary Actuator).png|alt= BE-SL&DS Vacuum Extended Reach (Rotary Actuator)|frameless|537x537px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41255005
|ARM-EXTENSION
|
|
|1
|-
|2
|HC0416
|CYLINDER-EXTENDED REACH
|
|
|1
|-
|3
|H1578
|ADAPTER-90 DEG-#6 JICM X #6 NPTM
|
|
|2
|-
|4
|41257031
|PIN-CLEVIS END
|
|
|1
|-
|5
|00197036
|PIN-ROD END
|
|
|1
|-
|6
|HW1058
|PIN-HITCH
|
|
|4
|}
[[File:IOP-400 BE-SL&DS (10-23) Vacuum Extended Reach 3 (Rotary Actuator).png|alt= BE-SL&DS Vacuum Extended Reach (Rotary Actuator)|frameless|537x537px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41255004
|HOUSING-EXTENDED REACH
|
|
|1
|-
|2
|41257030
|PLATE-END
|
|
|1
|-
|3
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|4
|-
|4
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|8
|-
|5
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|6
|HW0005
|NUT-HEX-3/8-16
|
|
|4
|-
|7
|41258002
|PLATE-BEARING
|
|''Side''
|2
|-
|8
|41258005
|PLATE-SHIM
|
|''Side''
|2
|-
|9
|41258003
|PLATE-BEARING
|
|''Upper/ Lower''
|2
|-
|10
|41258004
|PLATE-SHIM
|
|''Upper/ Lower''
|2
|-
|11
|HW0812
|SCREW-SHSS-1/4-20 X 5/8"-HALF DOG
|
|
|28
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|28
|}

==== <big>''Extended Reach Rotary Actuator''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Extended Reach (Rotary Actuator).png|alt=BE-SL & DS Extended Reach (Rotary Actuator)|frameless|538x538px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43046001
|ROTARY ACTUATOR
|
|
|1
|-
|2
|80000002
|ROTARY ACTUATOR BASE ASSEMBLY
|
|''Without Actuator''
|1
|-
|2A
|N/A
|VERTICAL CARRIER PLATE-OUTER
|
|''Included with 80000002''
|2
|-
|2B
|N/A
|VERTICAL CARRIER PLATE-INNER
|
|''Included with 80000002''
|1
|-
|2C
|N/A
|CARRIER BASE PLATE
|
|''Included with 80000002''
|1
|-
|3
|HW1070
|PIN-PULL DOWEL-5/8" X 1 1/2"
|
|
|2
|-
|4
|HW0508
|BOLT-SHCS-1/2-13 X 3/4"
|
|
|3
|-
|5
|HW1045
|PIN-PULL DOWEL-3/8" X 1 1/2"
|
|''Included with 80000002''
|6
|-
|6
|HW0412
|BOLT-SHCS-3/8-16 X 1 1/4"
|
|''Included with 80000002''
|12
|-
|7
|H0010
|FITTING-BULKHEAD-3/4-16 X #4 FNPT
|
|
|4
|-
|8
|H1579
|ADAPTER-90 DEG-#6 JICM X #4 NPTM
|
|
|4
|}
[[File:IOP-400 BE-SL&DS (10-23) Extended Reach 2 (Rotary Actuator).png|alt=BE-SL & DS Extended Reach |frameless|538x538px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|PT0634
|BRACKET-MALE END
|
|''Sold as set''
|1
|-
|2
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|4
|-
|3
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|10
|-
|4
|HW0103
|WASHER-LOCK-1/4"
|
|
|6
|-
|5
|HW0002
|NUT-HEX-1/4-20
|
|
|6
|-
|6
|PT0627
|HOSE CARRIER
|
|''14 Links required''
|39"
|-
|7
|PT0634
|BRACKET-FEMALE END
|
|''Sold as set''
|1
|-
|8
|HC0261
|VALVE-CROSS PORT RELIEF
|
|
|1
|-
|8a
|43046003
|REPLACEMENT CARTRIDGE
|
|''† For Item 8 (Not shown)''
|2
|-
|9
|HW0308
|BOLT-HHCS-1/4-20 X 2 1/2"
|
|
|2
|-
|10
|H1546
|ADAPTER-#6 JICM X #8 SAEM
|
|
|2
|-
|11
|H1617
|ADAPTER-45 DEG-#6 JICM X #8 SAEM
|
|
|2
|-
|12
|HC0237
|VALVE-SEQUENCING
|
|
|1
|-
|12a
|43046005
|REPLACEMENT CARTRIDGE
|
|''† For Item 12 (Not shown)''
|A/R
|-
|13
|HW0317
|BOLT-HHCS-1/4-20 X 3 1/2"
|
|
|2
|-
|14
|H1560
|ADAPTER-45 DEG-#8 JICM X #8 SAEM
|
|
|4
|-
|15
|H1600
|ADAPTER-90 DEG-#6 JICM X #8 SAEM
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Cartridges are for replacement only''
|}

==== <big>''Magnet Extended Reach (Rotary Actuator)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Magnet Extended Reach (Rotary Actuator).png|alt=BE-SL&DS Magnet Extended Reach (Rotary Actuator)|frameless|549x549px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43055011
|ARM-EXTENSION-MAGNET
|
|
|1
|-
|2
|HC0415
|CYLINDER-EXTENDED REACH-MAGNET
|
|''2 1/2" X 8" Cylinder''
|1
|-
|3
|H1578
|ADAPTER-90 DEG-#6 JICM X #6 MNPT
|
|
|2
|-
|4
|43057042
|PIN-CLEVIS END
|
|
|1
|-
|5
|43057043
|PIN-ROD END
|
|
|1
|-
|6
|HW1132
|RETAINING RING-EXTERNAL-3/4"I.D.
|
|
|4
|-
|7
|HW1043
|CLAMP-CYLINDER
|
|
|2
|-
|8
|43057044-2
|SUPPORT-CABLE
|
|
|2
|-
|9
|PL0501
|GROMMET-1/2" I.D.
|
|
|4
|-
|10
|43058019
|SUPPORT-CABLE-BAND CLAMP
|
|
|2
|-
|11
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|12
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|}
[[File:IOP-400 BE-SL&DS (10-23) Magnet Extended Reach Bearing and Shim (Rotary Actuator).png|alt=BE-SL&DS Magnet Extended Reach Bearing and Shim (Rotary Actuator)|frameless|556x556px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43055012
|HOUSING-EXTENDED REACH-MAGNET
|
|
|1
|-
|2
|50057008
|PLATE-END
|
|
|1
|-
|3
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|4
|-
|4
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|8
|-
|5
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|6
|HW0005
|NUT-HEX-3/8-16
|
|
|4
|-
|7
|43058013
|PLATE-BEARING-SIDE
|
|
|2
|-
|8
|43058016
|PLATE-SHIM-SIDE
|
|
|2
|-
|9
|43058014
|PLATE-BEARING-UPPER/LOWER
|
|
|2
|-
|10
|43058015
|PLATE-SHIM-UPPER/LOWER
|
|
|2
|-
|11
|HW0812
|SCREW-SHSS-1/4-20 X 5/8"-HALF DOG
|
|
|24
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|24
|}

==== <big>''Extended Reach End Plates''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Magnet Extended Reach End Plates (Rotary Actuator).png|alt=BE-SL&DS Magnet Extended Reach End Plates (Rotary Actuator)|frameless|574x574px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|N/A
|CARRIER SHAFT-EXTRACTOR ARM
|
|''† 3-Hole version''
|A/R
|-
|2
|PT0413
|COLLAR-SHAFT-3"
|
|
|4
|-
|3
|50057009
|PLATE-END-3 HOLE
|
|''Replacement part only''
|4
|-
|4
|50057010
|SHIM-END PLATE
|
|''†† See notes''
|A/R
|-
|5
|HW1076
|BOLT-FHSCS-3/8-16 X 1"
|
|
|12
|-
|6
|43057045
|CARRIER SHAFT-EXTRACTOR ARM
|
|''1-Hole version''
|2
|-
|7
|43017076
|PLATE-END-1 HOLE
|
|
|4
|-
|8
|HW0603
|BOLT-FHSCS-5/8-11 X 2"
|
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† 3-Hole Carrier Shaft no longer available. Must replace 3-Hole Shaft with current, 1-Hole version along with new End Plates and hardware.''
|-
| colspan="6" |''†† Shim quantity varies due to manufacturing tolerences.''
|}

=== <big>Carrier Shafts & Bearings ''(Helical Actuator)''</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Carrier Shaft BearingsEnd Plates (Helical Actuator).png|alt=BE-SL & BE-DS Carrier Shaft Bearings (Helical Actuator)|frameless|567x567px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43057045
|CARRIER SHAFT-EXTRACTOR ARM
|
|''† See notes''
|2
|-
|2
|43054007
|BEARING-EXTRACTOR ARM CARRIER
|80252002
|
|4
|-
|3
|HW0412
|BOLT-SHCS-3/8-16 X 1 1/4"
|80252002
|
|16
|-
|4
|PT0413
|COLLAR-SHAFT-3"
|
|
|4
|-
|5
|50057010
|SHIM-END PLATE
|
|
|A/R
|-
|6
|43017076
|PLATE-END-1 HOLE
|
|
|4
|-
|7
|HW0603
|BOLT-FHSCS-5/8-11 X 2"
|
|
|4
|-
|8
|PT0624
|FITTING-ZERK
|80252002
|''(Not shown)''
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† See [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Extended_Reach_End_Plates Extended Reach End Plates] section for Extended Reach equipped units.''
|}

=== <big>Drive Screw Components ''(Helical Actuator)''</big> ===

==== <big>''Drive Nut Assembly (Helical Actuator)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Drive Nut Assembly (Helical Actuator).png|alt=BE-SL&DS Drive Nut Assembly (Helical Actuator)|frameless|601x601px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43054006
|DRIVE NUT ASSEMBLY
|80252003
|
|1
|-
|2
|HW0426
|BOLT-SHCS-3/8-16 X 5 1/2"
|80252003
|''†'' ''See notes''
|4
|-
|3
|HW0108
|WASHER-FLAT-3/8"-SAE
|80252003
|''†'' ''See notes''
|4
|-
|4
|HW0006
|NUT-NILN-3/8-16
|80252003
|''†'' ''See notes''
|4
|-
|5
|PT0624
|FITTING-ZERK
|80252003
|
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† It is recommended to replace Mounting Hardware when replacing Drive Nut Assembly.''
|}

=== <big>Swing Arms & Actuator ''(Helical Actuator)''</big> ===

==== ''<big>[Discontinued] Helical Actuator (Prior to July 2023)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Helical Actuator.png|alt= BE-SL&DS Discontinued Helical Actuator used prior to July 2023|frameless|551x551px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|N/A
|HELICAL ACTUATOR
|
|''†'' ''See notes''
|1
|-
|2
|43057046
|ACTUATOR BASE PLATE
|
|
|1
|-
|3
|43058022
|SPACER-ACTUATOR
|
|
|4
|-
|4
|HW0725
|BOLT-HHCS-3/4-16 X 4-3/4"-GR8
|
|
|4
|-
|5
|HW0066
|NUT-JAM-3/4-16-GR8
|
|
|4
|-
|6
|43055013
|SWING ARM-LHS
|
| rowspan="6" |''††'' ''See notes''
|1
|-
|7
|HW0620
|BOLT-HHCS-5/8-11 X 1-1/4"
|
|6
|-
|8
|HW0113
|WASHER-LOCK-5/8"
|
|6
|-
|9
|43055014
|SWING ARM-RHS
|
|1
|-
|10
|HW0502
|BOLT-HHCS-1/2-13 X 1-1/4"
|
|6
|-
|11
|HW0110
|WASHER-LOCK-1/2"
|
|6
|-
|12
|43042008
|3/8" TUBE X #6 JIC HARD-PIPE
|
|
|1
|-
|13
|43042010
|3/8" TUBE X #6 JIC HARD-PIPE, LONG
|
|
|1
|-
|14
|H1619
|ADAPTER-90 DEG-#6 JICM X #4 SAEM
|
|
|2
|-
|15
|H0010
|FITTING-H-BULKHEAD-1/4" FNPT
|
|
|2
|-
|16
|H1504
|ADAPTER-#6 JICM X #4 NPTM
|
|
|2
|-
|17
|HW1082
|CLAMP-HOSE
|
|
|1
|-
|18
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Discontinued Helical Actuator no longer available. Must replace with current Helical Actuator Retro Kit 80252032. See [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Current_Helical_Actuator Current Helical Actuator] section.''

''†† Swing Arms manufactured prior to January 2022 use 10 Bolts & Washer per Swing Arm.''
|}

==== ''<big>[Current] Helical Actuator (July 2023 to Present)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Current Helical Actuator.png|alt= BE-SL&DS Current Helical Actuator used July 2023 to Present|frameless|571x571px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|N/A
|43052020
|HELICAL ACTUATOR ASSEMBLY
|
|''Includes Items 1 through 17''
|1
|-
|1
|HC0180
|HELICAL ACTUATOR
|80252032
|
|1
|-
|2
|43057046
|ACTUATOR BASE PLATE
|
|
|1
|-
|3
|43058022
|SPACER-ACTUATOR
|
|
|4
|-
|4
|HW0725
|BOLT-HHCS-3/4-16 X 4-3/4"-GR8
|
|
|4
|-
|5
|HW0066
|NUT-JAM-3/4-16-GR8
|
|
|4
|-
|6
|43055013
|SWING ARM-LHS
|
|
|1
|-
|7
|HW0620
|BOLT-HHCS-5/8-11 X 1-1/4"
|
|
|6
|-
|8
|HW0113
|WASHER-LOCK-5/8"
|
|
|6
|-
|9
|43055014
|SWING ARM-RHS
|
|
|1
|-
|10
|HW0502
|BOLT-HHCS-1/2-13 X 1-1/4"
|
|
|6
|-
|11
|HW0110
|WASHER-LOCK-1/2"
|
|
|6
|-
|12
|43042011
|3/8" TUBE X #6 JIC HARD-PIPE, 90 DEG
|80252032
|''†'' ''See notes''
|1
|-
|13
|43042012
|3/8" TUBE X #6 JIC HARD-PIPE, SHORT
|80252032
|''†'' ''See notes''
|1
|-
|14
|H1619
|ADAPTER-90 DEG-#6 JICM X #4 SAEM
|80252032
|
|2
|-
|15
|H0010
|FITTING-H-BULKHEAD-1/4" FNPT
|
|
|2
|-
|16
|H1504
|ADAPTER-#6 JICM X #4 NPTM
|80252032
|
|1
|-
|17
|H1691
|ADAPTER-45 DEG-#6 JICM X #4 NPTM
|80252032
|''†'' ''See notes''
|1
|-
|18
|HW1082
|CLAMP-HOSE
|
|
|1
|-
|19
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Hard-Pipes and 45-Degree Adapter required if replacing discontinued Actuator with current Actuator. Kit PT# 80252032 required for discontinued Actuator replacement.''
|}

=== <big>Swing Arm Stops & Tie Plate ''(Helical Actuator)''</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Swing Arm Stops and Tie Plate (Helical Actuator).png|alt=BE-SL&DS Swing Arm Stops and Tie Plate (Helical Actuator)|frameless|549x549px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43057050
|TIE PLATE-HELICAL SWING ARM
|
|
|1
|-
|2
|HW0603
|BOLT-FHSCS-5/8-11 X 2"
|
|
|4
|-
|3
|HW0113
|WASHER-LOCK-5/8"
|
|
|4
|-
|4
|HW0010
|NUT-JAM-5/8-11
|
|
|4
|-
|5
|43057052
|STOP-POLY-SWING ARM
|
|''†'' ''See notes''
|4
|-
|6
|HW0441
|BOLT-FHSCS-3/8-16 X 1-1/2"
|
|
|4
|-
|7
|HW0031
|NUT-LOCK-3/8-16, DEFORMED THREAD
|
|''††'' ''See notes''
|4
|-
|8
|44555002
|SWING ARM STOP
|
|''Single compartment units only''
|A/R
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Replacement Poly Stop design updated from square to round. Stop Spacers not required with current, round-style Stops.''
|-
| colspan="6" |''†† Deformed Thread Lock Nut replaces Acorn Nut and Split Lock Washer used previously.''
|}

=== <big>'''Push/Pull Arm Mounting ''(Helical Actuator)'''''</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Push Pull Arm Mounting (Helical Actuator).png|alt=BE-SL & BE-DS Push Pull Arm Mounting (Helical Actuator)|frameless|581x581px]]
{| class="wikitable"
! rowspan="2" |ITEM
! rowspan="2" |BHS PART NUMBER
! rowspan="2" |DESCRIPTION
! rowspan="2" |REF. KIT NO.
! rowspan="2" |NOTES
! colspan="3" |NO. REQ
|-
!BE-24
!BE-36
!BE-42
|-
| rowspan="2" |1
|41655008
|EXTENSION-ARM
|
|''† BE-36 units only''
|<nowiki>-</nowiki>
|1
|<nowiki>-</nowiki>
|-
|43455001
|EXTENSION-ARM
|
|''† BE-42 units only''
|<nowiki>-</nowiki>
|<nowiki>-</nowiki>
|1
|-
|2
|HW0504
|BOLT-HHCS-1/2-13 X 2"
|
|
|6
| colspan="2" |12
|-
|3
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|12
| colspan="2" |24
|-
|4
|HW0110
|WASHER-LOCK-1/2"
|
|
|6
| colspan="2" |12
|-
|5
|HW0007
|NUT-HEX-1/2-13
|
|
|6
| colspan="2" |12
|-
! colspan="8" |NOTES
|-
| colspan="8" |''† BE-24 units do not utilize an arm extension.''
|}

=== <big>Vacuum Extractor Arm ''(Helical Actuator)''</big> ===

==== ''<big>Non-Pivoting Vacuum Cup Arm (Helical Actuator)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Non-Pivoting Vaccum Cup Arm (Helical Actuator).png|alt=BE-SL & BE-DS Non-Pivoting Vacuum Cup Arm (Helical Actuator)|frameless|567x567px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HW0428
|STUD-VACUUM-3/8-16 X 5"
|HW-KIT-2
|
|8
|-
|2
|HW0108
|WASHER-FLAT-3/8"-SAE
|HW-KIT-2
|
|40
|-
|3
|HW1001
|SPRING-3/8"
|HW-KIT-2
|
|24
|-
|4
|HW0424
|NUT-JAM-3/8-16
|HW-KIT-2
|
|8
|-
|5
|HW0006
|NUT-NILN-3/8-16
|HW-KIT-2
|
|8
|-
|6
|P0402
|HOSE BARB-1/4" X #4 MNPT-BRASS
|
|
|2
|-
|REF
|43052014
|ADJUSTABLE PUSH-PULL ARM
|
|''Includes Items 7 through 11''
|A/R
|-
|7
|43055018
|ARM BASE
|
|
|1
|-
|8
|43055019
|VACUUM CUP MOUNT
|
|
|2
|-
|9
|HW0523
|BOLT-HHCS-1/2-13 X 4"
|
|
|2
|-
|10
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|4
|-
|11
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|}

==== ''<big>Pivoting Vacuum Cup Arm (Helical Actuator)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Pivoting Vacuum Cup Arm (Helical Actuator).png|alt=BE-SL & BE-DS Pivoting Vacuum Extractor Cup Arm (Helical Actuator)|frameless|551x551px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43052014
|ADJUSTABLE PUSH-PULL ARM
|
|''Includes Items 1 through 5''
|A/R
|-
|1
|43055018
|ARM BASE
|
|
|1
|-
|2
|43055019
|VACUUM CUP MOUNT
|
|
|2
|-
|3
|HW0523
|BOLT-HHCS-1/2-13 X 4"
|
|
|2
|-
|4
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|4
|-
|5
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|-
|6
|43055020
|MOUNT-PIVOT-VACUUM CUP
|
|
|2
|-
|7
|PT0470
|BEARING-PIVOT
|
|
|2
|-
|8
|HW0525
|BOLT-CARRIAGE-1/2-13 X 1 1/2"
|
|
|12
|-
|9
|HW0524
|BOLT-CARRIAGE-1/2-13 X 2"
|
|
|4
|-
|10
|HW0110
|WASHER-LOCK-1/2"
|
|
|16
|-
|11
|HW0008
|NUT-HEX-1/2-13
|
|
|16
|-
|12
|43058009
|PLATE-ROTATION STOP
|
|
|2
|-
|13
|43058003
|SLEEVE-STOP
|
|
|2
|-
|14
|43058010
|SUPPORT-CABLE
|
|
|2
|-
|15
|E0622
|RESTRAINT-1/2"
|
|''Grip size .450" to .560"''
|4
|-
|16
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|4
|-
|17
|HW0523
|BOLT-HHCS-1/2-13 X 4"
|
|
|2
|-
|18
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|-
|19
|43037002-2
|SUPPORT-CABLE RESTRAINT
|
|
|2
|-
|20
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|4
|-
|21
|P0506
|ELBOW-STR-90 DEG-#4 NPT-BRASS
|
|
|2
|-
|22
|P0402
|HOSE BARB-1/4" X #4 MNPT-BRASS
|
|
|2
|-
|23
|43057056-2
|BRACKET-HOSE SUPPORT
|
|
|2
|-
|24
|PL0507
|GROMMET-5/8" I.D.
|
|
|2
|-
|25
|P0302
|HOSE-VACUUM-1/4" I.D.
|
|''2 Pieces at 48" each''
|96"
|-
|26
|HW0443
|BOLT-HHCS-3/8-16 X 3-1/2"
|HW-KIT-3
|
|8
|-
|27
|HW1001
|SPRING-3/8"
|HW-KIT-3
|
|16
|-
|28
|HW0108
|WASHER-FLAT-3/8"-SAE
|HW-KIT-3
|
|32
|-
|29
|HW0424
|NUT-JAM-3/8-16
|HW-KIT-3
|
|4
|}

==== ''<big>Single Compartment Vacuum Cup Rotation Stop</big>'' ''<big>(Helical Actuator)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Single Compartment Rotation Stop (Helical Actuator).png|alt=BE-SL & BE-DS Vacuum Cup Rotation Stop (Helical Actuator)|frameless|568x568px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|445558001
|PLATE-ROTATION STOP
|
|''Single compartment units only''
|2
|-
|2
|HW0525
|BOLT-CARRIAGE-1/2-13 X 1 1/2"
|
|
|2
|-
|3
|HW0524
|BOLT-CARRIAGE-1/2-13 X 2"
|
|
|6
|-
|4
|HW0110
|WASHER-LOCK-1/2"
|
|
|8
|-
|5
|HW0008
|NUT-HEX-1/2-13
|
|
|8
|}

==== <big>''Vacuum Components (Helical Actuator)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Vacuum Pump Components (Helical Actuator).png|alt=BE-SL & BE-DS Vacuum Pump Components (Helical Actuator)|frameless|537x537px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43058021
|STIFFENER PLATE-HELICAL SWING ARM
|
|
|2
|-
|2
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|12
|-
|3
|HW0108
|WASHER-FLAT-3/8"
|
|
|24
|-
|4
|HW0107
|WASHER-LOCK-3/8"
|
|
|12
|-
|5
|HW0005
|NUT-HEX-3/8-16
|
|
|12
|-
|6
|P0005
|PUMP-VACUUM
|
|
|1
|-
|7
|P0207
|VALVE-VACUUM RELEASE
|
|
|2
|-
|8
|P0208
|FILTER-HI FLOW
|
|
|3
|-
|9
|H0011
|NIPPLE-#4 X 2"-BRASS
|
|
|1
|-
|10
|P0502
|TEE-#4 FNPT-BRASS
|
|
|1
|-
|11
|P0506
|ELBOW-STR-90 DEG-#4 NPT-BRASS
|
|
|4
|-
|12
|P0503
|NIPPLE-#4 NPT-BRASS
|
|
|2
|-
|13
|P0402
|HOSE BARB-1/4" X #4 MNPT-BRASS
|
|
|6
|-
|14
|P0111
|FILTER-VACUUM-IN-LINE
|
|
|2
|-
|15
|HW0206
|SCREW-RHMS-#10-32 X 3/4"
|
|
|4
|-
|16
|43037014-2
|BRACKET-CABLE RESTRAINT
|
|
|1
|-
|17
|E0622
|RESTRAINT-1/2"
|
|''Grip size .450" to .560"''
|2
|-
|18
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|2
|-
|19
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
|20
|E0611
|JUNCTION BOX-4" X 2" X 2"
|
|
|1
|-
|21
|E0612
|COVER-JUNCTION BOX
|
|
|1
|-
|22
|E0624
|CONNECTOR-1/2"
|
|''Includes Lock Nut''
|1
|-
|23
|HW0212
|SCREW-RHMS-#10-24 X 1/2"
|
|
|2
|}

=== <big>Magnet Extractor Arm ''(Helical Actuator)''</big> ===

==== <big>''Magnet Arm (Helical Actuator)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Magnet Arm (Helical Actuator).png|alt=BE-SL & BE-DS Magnet Arm (Helical Actuator)|frameless|555x555px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43052014
|ADJUSTABLE PUSH-PULL ARM
|
|''Includes Items 1 through 5''
|A/R
|-
|1
|43055018
|ARM BASE
|
|
|1
|-
|2
|43055019
|VACUUM CUP MOUNT
|
|
|2
|-
|3
|HW0523
|BOLT-HHCS-1/2-13 X 4"
|
|
|2
|-
|4
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|4
|-
|5
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|-
|6
|43055016
|MOUNT-PIVOT-MAGNET
|
|
|2
|-
|7
|PT0470
|BEARING-PIVOT
|
|
|2
|-
|8
|HW0525
|BOLT-CARRIAGE-1/2-13 X 1 1/2"
|
|
|12
|-
|9
|HW0524
|BOLT-CARRIAGE-1/2-13 X 2"
|
|
|4
|-
|10
|HW0110
|WASHER-LOCK-1/2"
|
|
|16
|-
|11
|HW0008
|NUT-HEX-1/2-13
|
|
|16
|-
|12
|43058009
|PLATE-ROTATION STOP
|
|
|2
|-
|13
|43058003
|SLEEVE-STOP
|
|
|2
|-
|14
|43058010
|SUPPORT-CABLE
|
|
|2
|-
|15
|HW0523
|BOLT-HHCS-1/2-13 X 4"
|
|
|2
|-
|16
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|-
|17
|E0622
|RESTRAINT-1/2"
|
|''Grip Size .450" to .560"''
|2
|-
|18
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|2
|-
|19
|43037002-2
|SUPPORT-CABLE RESTRAINT
|
|
|2
|-
|20
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|4
|-
|21
|E0334-6'
|CORD-5 PIN FEMALE
|
|''With 72" Lead''
|2
|-
|22
|E1041
|WIRE LOOM-SPIRAL-3/8"
|
|''2 Pieces at 24" each''
|48"
|-
|23
|PL0501
|GROMMET-1/2" I.D.
|
|
|2
|-
|24
|43057037
|INSULATOR-BOTTOM
|
|
|2
|-
|25
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|8
|-
|26
|41657008
|SLIDE-MAGNET
|
|
|2
|-
|27
|HW0314
|BOLT-FHSCS-1/4-20 X 1/2"
|
|
|4
|}

==== <big>''Magnet Assembly (Helical Actuator)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Magnet Assembly (Helical Actuator).png|alt=BE-SL & BE-DS Magnet Assembly (Helical Actuator)|frameless|550x550px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43032009
|MAGNET ASSEMBLY
|
|''Includes items 1 through 12''
|A/R
|-
|1
|N/A
|ELECTROMAGNET-95VDC
|
|
|2
|-
|2
|E0314
|SENSOR-PROXIMITY-30MM
|
|
|2
|-
|3
|41657002
|COVER-PROXIMITY SENSOR HOUSING
|
|''Rear''
|2
|-
|4
|HW1065
|SCREW-SHCS-#6-32 X 3/8"
|
|
|8
|-
|5
|HW1066
|WASHER-LOCK-#6
|
|
|8
|-
|6
|E0335
|RECEPTACLE-5 PIN MALE
|
|''With 12" Lead''
|2
|-
|7
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|2
|-
|8
|E0376
|INDICATOR LIGHT
|
|''† See notes''
|2
|-
|9
|41657003
|COVER-PROXIMITY SENSOR HOUSING
|80252015
|''Front''
|2
|-
|10
|HW0138
|SCREW-FHSCS-#8-32 X 3/8"
|80252015
|
|8
|-
|11
|HW0514
|BOLT-HHCS-1/2-13 X 2 1/2"
|80252014
|
|4
|-
|12
|HW1002
|SPRING-1/2"
|80252014
|
|4
|-
|13
|HW0112
|WASHER-FLAT-1/2"-SAE
|80252014
|
|8
|-
|14
|HW0007
|NUT-HEX-1/2-13
|80252014
|
|4
|-
|15
|E0336
|METAL OXIDE VARISTOR
|
|''Not shown''
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Extractors built or Replacement Magnets shipped prior to October 2021 used Multi-piece Indicator Lights with Replaceable Bulb and Lens and are no longer available.''

''Current Indicator Light is a 1-Piece LED assembly. Replacement of any Multi-Piece Component requires replacing entire assembly with current, 1-Piece Indicator Light''
|}

==== <big>''Magnet Components (Helical Actuator)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Magnet Components (Helical Actuator).png|alt=BE-SL & BE-DS Magnet Components (Helical Actuator)|frameless|545x545px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43058021
|STIFFENER PLATE-HELICAL SWING ARM
|
|
|1
|-
|2
|43057051-2
|STIFFENER-MAGNET-HELICAL SWING ARM
|
|
|1
|-
|3
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|12
|-
|4
|HW0108
|WASHER-FLAT-3/8"
|
|
|24
|-
|5
|HW0107
|WASHER-LOCK-3/8"
|
|
|12
|-
|6
|HW0005
|NUT-HEX-3/8-16
|
|
|12
|-
|7
|PL0307
|INSULATOR-MALE STUD
|
|
|4
|-
|8
|HW0106
|WASHER-FLAT-5/16"-SAE
|
|
|8
|-
|9
|HW0105
|WASHER-LOCK-5/16"
|
|
|8
|-
|10
|HW0004
|NUT-HEX-5/16-18
|
|
|8
|-
|11
|E0622
|RESTRAINT-1/2"
|
|''Grip Size .450" to .560"''
|1
|-
|12
|E0608-1
|RESTRAINT-1/2"-90 DEG
|
|''Grip Size .450" to .560"''
|2
|-
|13
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|3
|-
|14
|E1016
|FUSE HOLDER
|
|
|1
|-
|15
|E0325
|FUSE-7 AMP-250VAC
|
|''FLM-7 or FNM-7''
|1
|-
|16
|HW0130
|SCREW-RHMS-#8-32 X 1/2"
|
|
|1
|-
|17
|HW0133
|WASHER-FLAT-#8-SAE
|
|
|1
|-
|18
|HW0132
|NUT-NILN-#8-32
|
|
|1
|}

==== <big>''Magnet Electrical Panel (Helical Actuator)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Magnet Electrical Panel (Helical Actuator).png|alt=BE-SL & BE-DS Magnet Electrical Panel (Helical Actuator)|frameless|536x536px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41637001
|PANEL-COMPONENT MOUNTING
|
|
|1
|-
|2
|41637002
|WIRE WAY-SHORT
|
|
|2
|-
|3
|41637003
|WIRE WAY-LONG
|
|
|1
|-
|4
|41637004
|TRACK-MOUNTING-SHORT
|
|
|1
|-
|5
|41637005
|TRACK-MOUNTING-LONG
|
|
|1
|-
|6
|HW0130
|SCREW-RHMS-#8-32 X 1/2"
|
| rowspan="3" |''Mounting Track Hardware not shown''
|10
|-
|7
|HW0132
|WASHER-FLAT-#8-SAE
|
|10
|-
|8
|HW0133
|NUT-NILN-#8-32
|
|16
|-
|9
|E1020
|TERMINAL BLOCK
|
|
|12
|-
|10
|E1040
|END BARRIER
|
|
|2
|-
|11
|E1330
|END ANCHOR
|
|
|4
|-
|12
|E1009
|RECTIFIER-FULL WAVE BRIDGE
|
|
|2
|-
|13
|HW0135
|SCREW-RHMS-#8-32 X 3/4"
|
|
|2
|-
|14
|E1313
|SOCKET-RELAY-8 PIN
|
|
|2
|-
|15
|E0331
|RELAY-DPDT-110VAC
|
|''With Indicator Light''
|2
|-
|16
|HW0139
|SCREW-RHMS-#8-32 X 1 1/4"
|
|
|4
|}

=== <big>Extended Reach Hydraulics ''(Helical Actuator)''</big> ===

==== ''<big>[Discontinued] Helical Actuator (Prior to July 2023)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Extended Reach Discontinued Helical Actuator.png|alt=BE-SL & BE-DS Discontinued Helical Actuator|frameless|589x589px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43042009
|3/8" TUBE X #6 JIC HARD-PIPE
|
|
|2
|-
|2
|H1579
|ADAPTER-90 DEG-#6 JICM X #4 MNPT
|
|
|2
|-
|3
|H0010
|FITTING-BULKHEAD-3/4-16 X #4 FNPT
|
|
|2
|-
|4
|43055017
|ELBOW-BULKHEAD
|
|
|2
|-
|5
|HW0302
|BOLT-HHCS-1/4-20 X 3/4"
|
|
|4
|-
|6
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
| rowspan="3" |7
|4-48-0402-0402
|HYD HOSE-1/4" X 48" (BE-24 UNITS)
|
| rowspan="3" |''Cylinder Rod-End Hose''
| rowspan="3" |1
|-
|4-54-0402-0402
|HYD HOSE-1/4" X 54" (BE-36 UNITS)
|
|-
|4-56-0402-0402
|HYD HOSE-1/4" X 56" (BE-42 UNITS)
|
|-
| rowspan="3" |8
|4-38-0402-0402
|HYD HOSE-1/4" X 38" (BE-24 UNITS)
|
| rowspan="3" |''Cylinder Base-End Hose''
| rowspan="3" |1
|-
|4-44-0402-0402
|HYD HOSE-1/4" X 44" (BE-36 UNITS)
|
|-
|4-46-0402-0402
|HYD HOSE-1/4" X 46" (BE-42 UNITS)
|
|-
|9
|41257035
|STANDOFF-HOSE
|
|
|2
|-
|10
|HW1093
|CLAMP-CABLE-3/4"
|
|
|2
|-
|11
|HW0311
|BOLT-FHSCS-1/4-20 X 3/4"
|
|
|2
|-
|12
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|}

==== ''<big>[Current] Helical Actuator (July 2023 to Present)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Extended Reach Current Helical Actuator.png|alt=BE-SL & BE-DS Current Extended Reach Helical Actuator|frameless|572x572px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43042013
|3/8" TUBE X #6 JIC HARD-PIPE
|
|
|2
|-
|2
|H1579
|ADAPTER-90 DEG-#6 JICM X #4 MNPT
|
|
|2
|-
|3
|H0010
|FITTING-BULKHEAD-3/4-16 X #4 FNPT
|
|
|2
|-
|4
|43055021
|ELBOW-BULKHEAD
|
|
|2
|-
|5
|HW0302
|BOLT-HHCS-1/4-20 X 3/4"
|
|
|4
|-
|6
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
| rowspan="3" |7
|4-48-0402-0402
|HYD HOSE-1/4" X 48" (BE-24 UNITS)
|
| rowspan="3" |''Cylinder Rod-End Hose''
| rowspan="3" |1
|-
|4-54-0402-0402
|HYD HOSE-1/4" X 54" (BE-36 UNITS)
|
|-
|4-56-0402-0402
|HYD HOSE-1/4" X 56" (BE-42 UNITS)
|
|-
| rowspan="3" |8
|4-38-0402-0402
|HYD HOSE-1/4" X 38" (BE-24 UNITS)
|
| rowspan="3" |''Cylinder Base-End Hose''
| rowspan="3" |1
|-
|4-44-0402-0402
|HYD HOSE-1/4" X 44" (BE-36 UNITS)
|
|-
|4-46-0402-0402
|HYD HOSE-1/4" X 46" (BE-42 UNITS)
|
|-
|9
|41257035
|STANDOFF-HOSE
|
|
|2
|-
|10
|HW1093
|CLAMP-CABLE-3/4"
|
|
|2
|-
|11
|HW0311
|BOLT-FHSCS-1/4-20 X 3/4"
|
|
|2
|-
|12
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|}

==== ''<big>Vacuum Extended Reach (Helical Actuator)</big>'' ====

===== '''''Non-Pivoting Cup Extended Reach Vacuum Arm (Helical Actuator) [Prior to October 2022]''''' =====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Non Pivoting Cup Extended Reach Vacuum Arm (Helical Actuator).png|alt=BE-SL & BE-DS Non-Pivoting Cup Extended Reach Vacuum Arm (Helical Actuator)|frameless|541x541px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41255005
|ARM-EXTENSION
|
|
|1
|-
|2
|41255004
|HOUSING-EXTENDED REACH
|
|
|1
|-
|3
|HC0416
|CYLINDER-2 1/2" X 12"
|
|
|1
|-
|4
|43057042
|PIN-CYLINDER-REAR
|
|
|1
|-
|5
|43057043
|PIN-CYLINDER-ROD
|
|
|1
|-
|6
|HW1132
|RETAINING RING-3/4" I.D.
|
|
|4
|-
|7
|H1578
|ADAPTER-90 DEG-#6 JIC X # 6 NPT
|
|
|2
|-
|8
|50057008
|PLATE-END
|
|
|1
|-
|9
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|10
|HW0104
|WASHER-FLAT-1/4"
|
|
|8
|-
|11
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|13
|HW0812
|SCREW-SHSS-1/4-20 X 5/8"-HALF DOG
|
|
|28
|-
|14
|HW0002
|NUT-HEX-1/4-20
|
|
|28
|-
|15
|41258002
|PLATE-BEARING
|80258001
|''Side''
|2
|-
|16
|41258005
|PLATE-SHIM
|80258001
|''Side''
|2
|-
|17
|41258003
|PLATE-BEARING
|80258001
|''Upper/Lower''
|2
|-
|18
|41258004
|PLATE-SHIM
|80258001
|''Upper/Lower''
|2
|}

===== '''''[Current] Pivoting Cup Extended Reach Vacuum Arm''''' '''''(Helical Actuator) [October 2022 to Present]''''' =====
[[File:IOP-400 BE-SL&DS (10-23) Pivoting Cup Extended Reach Vaccum Arm (Helical Actuator).png|alt=BE-SL & BE-DS Pivoting Cup Extended Reach Vacuum Arm (Helical Actuator)|frameless|571x571px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43055011
|ARM-EXTENSION
|
|''Pivoting cup only''
|1
|-
|2
|43055012
|HOUSING-EXTENDED REACH
|
|''Pivoting cup only''
|1
|-
|3
|HC0415
|CYLINDER-2 1/2" X 8"
|
|
|1
|-
|4
|43057042
|PIN-CYLINDER-REAR
|
|
|1
|-
|5
|43057043
|PIN-CYLINDER-ROD
|
|
|1
|-
|6
|HW1132
|RETAINING RING-3/4" I.D.
|
|
|4
|-
|7
|H1578
|ADAPTER-90 DEG-#6 JIC X # 6 NPT
|
|
|2
|-
|8
|50057008
|PLATE-END
|
|
|1
|-
|9
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|10
|HW0104
|WASHER-FLAT-1/4"
|
|
|8
|-
|11
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|13
|HW0812
|SCREW-SHSS-1/4-20 X 5/8"-HALF DOG
|
|
|24
|-
|14
|HW0002
|NUT-HEX-1/4-20
|
|
|24
|-
|15
|43058013
|PLATE-BEARING
|
|''Side''
|2
|-
|16
|43058016
|PLATE-SHIM
|
|''Side''
|2
|-
|17
|43058014
|PLATE-BEARING
|
|''Upper/ Lower''
|2
|-
|18
|43058015
|PLATE-SHIM
|
|''Upper/ Lower''
|2
|-
|19
|HW1043
|CLAMP-CYLINDER
|
|
|2
|-
|20
|43058019
|SUPPORT-CABLE-BAND CLAMP
|
|
|2
|-
|21
|E0622
|RESTRAINT-1/2"
|
|''Grip size .450" to .560"''
|2
|-
|22
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|2
|-
|23
|HW0104
|WASHER-FLAT-1/4"
|
|
|4
|-
|24
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|}

==== ''<big>'''Magnet Extended Reach (Helical Actuator)'''</big>'' ====

===== '''''[Discontinued] Extended Reach Magnet Arm (Helical Actuator) [Prior to October 2022]''''' =====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Extended Reach Magnet Arm (Helical Actuator).png|alt=BE-SL & BE-DS Discontinued Extended Reach Magnet Arm (Helical Actuator)|frameless|531x531px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43055011
|ARM-EXTENSION
|
|
|1
|-
|2
|43055012
|HOUSING-EXTENDED REACH
|
|
|1
|-
|3
|HC0415
|CYLINDER-2 1/2" X 8"
|
|
|1
|-
|4
|43057042
|PIN-CYLINDER-REAR
|
|
|1
|-
|5
|43057043
|PIN-CYLINDER-ROD
|
|
|1
|-
|6
|HW1132
|RETAINING RING-3/4" I.D.
|
|
|4
|-
|7
|H1578
|ADAPTER-90 DEG-#6 JIC X # 6 NPT
|
|
|2
|-
|8
|50057008
|PLATE-END
|
|
|1
|-
|9
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|10
|HW0104
|WASHER-FLAT-1/4"
|
|
|8
|-
|11
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|13
|HW0812
|SCREW-SHSS-1/4-20 X 5/8"-HALF DOG
|
|
|24
|-
|14
|HW0002
|NUT-HEX-1/4-20
|
|
|24
|-
|15
|43058013
|PLATE-BEARING
|
|''Side''
|2
|-
|16
|43058016
|PLATE-SHIM
|
|''Side''
|2
|-
|17
|43058014
|PLATE-BEARING
|
|''Upper / Lower''
|2
|-
|18
|43058015
|PLATE-SHIM
|
|''Upper / Lower''
|2
|-
|19
|HW1043
|CLAMP-CYLINDER
|
|
|2
|-
|20
|43058019
|SUPPORT-CABLE-BAND CLAMP
|
|
|2
|-
|21
|PL0501
|GROMMET-1/2" I.D.
|
|
|4
|-
|22
|HW0104
|WASHER-FLAT-1/4"
|
|
|4
|-
|23
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|24
|43057004-2
|SUPPORT-CABLE-MAGNET
|
|
|2
|}

===== ''[Current] Extended Reach Magnet Arm (Helical Actuator) [October 2022 to Present]'' =====
[[File:IOP-400 BE-SL&DS (10-23) Current Extended Reach Magnet Arm (Helical Actuator).png|alt=BE-SL & BE-DS Current Extended Reach Magnet Arm (Helical Actuator)|frameless|532x532px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|50055004
|ARM-EXTENSION
|
|
|1
|-
|2
|50055005
|HOUSING-EXTENDED REACH
|
|
|1
|-
|3
|HC0415
|CYLINDER-2 1/2" X 8"
|
|
|1
|-
|4
|43057042
|PIN-CYLINDER-REAR
|
|
|1
|-
|5
|43057043
|PIN-CYLINDER-ROD
|
|
|1
|-
|6
|HW1132
|RETAINING RING-3/4" I.D.
|
|
|4
|-
|7
|H1578
|ADAPTER-90 DEG-#6 JIC X # 6 NPT
|
|
|2
|-
|8
|50057008
|PLATE-END
|
|
|1
|-
|9
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|10
|HW0104
|WASHER-FLAT-1/4"
|
|
|8
|-
|11
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|13
|HW0812
|SCREW-SHSS-1/4-20 X 5/8"-HALF DOG
|
|
|20
|-
|14
|HW0002
|NUT-HEX-1/4-20
|
|
|20
|-
|15
|50058009
|PLATE-BEARING
|
|''Side''
|2
|-
|16
|50058012
|PLATE-SHIM
|
|''Side''
|2
|-
|17
|50058010
|PLATE-BEARING
|
|''Upper/ Lower''
|2
|-
|18
|50058011
|PLATE-SHIM
|
|''Upper/ Lower''
|2
|-
|19
|HW1043
|CLAMP-CYLINDER
|
|
|2
|-
|20
|43058019
|SUPPORT-CABLE-BAND CLAMP
|
|
|2
|-
|21
|PL0501
|GROMMET-1/2" I.D.
|
|
|4
|-
|22
|HW0104
|WASHER-FLAT-1/4"
|
|
|4
|-
|23
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|24
|43057004-2
|SUPPORT-CABLE-MAGNET
|
|
|2
|}

== <big>Floor Drive & Casters</big> ==

=== <big>Drive Wheel Assembly</big> ===

==== ''<big>Discontinued Drive Wheel Assembly (Prior to November 2012)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Drive Wheel Assembly.png|alt=BE-SL & BE-DS Discontinued Drive Wheel Assembly (Prior to November 2012)|frameless|540x540px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43715012
|FRAME-FLOOR DRIVE
|
|
|2
|-
| rowspan="2" |2
|HW0515
|BOLT-HHCS-1/2-13 X 2"-FULL THREAD
|
|
|6
|-
|HW0517
|BOLT-HHCS-1/2-13 X 2 1/2"-FULL THREAD
|
|''Cylinder support bracket bolt''
|2
|-
|3
|HW0110
|WASHER-LOCK-1/2"
|
|
|8
|-
|4
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|8
|-
|5
|C0050-2
|WHEEL-8" X 3"-POLY
|80222001
|
|2
|-
|6
|PT0406
|FLANGE BEARING-4 BOLT-1 3/16"
|80222001
|''Alloy casting''
|4
|-
|7
|HW0504
|BOLT-HHCS-1/2-13 X 2"
|
|
|8
|-
|8
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|8
|-
|9
|HW0110
|WASHER-LOCK-1/2"
|
|
|24
|-
|10
|HW0007
|NUT-HEX-1/2-13
|
|
|24
|-
|11
|43797001
|ROD-THREADED-1/2-13 X 7"
|
|
|8
|-
|12
|43727007
|SPACER-DRIVE WHEEL
|
|
|8
|-
|13
|43727006
|PLATE-MOTOR MOUNTING
|
|
|2
|-
|14
|N/A
|SHAFT-WHEEL
|
|''† See notes''
|2
|-
|15
|43097005
|KEY-1/4" X 3"
|80222001
|
|2
|-
|16
|00197028
|KEY-1/4" X 1 1/4"
|
|
|2
|-
|17
|N/A
|BUSHING-TAPER LOCK-1 3/16"
|
|''†'' ''Shaft side''
|2
|-
|18
|N/A
|COUPLING BODY-TAPER BORE-#50
|
|''†'' ''See notes''
|4
|-
|19
|HW0323
|BOLT-HHCS-5/16-18 X 1"
|80222001
|
|16
|-
|20
|PT0321
|CHAIN-COUPLING-#50
|
|''Includes Connecting Pin''
|2
|-
|21
|N/A
|BUSHING-TAPER LOCK-1"
|
|''†'' ''Motor side''
|2
|-
|22
|N/A
|MOTOR-HYDRAULIC-160CC
|
|''†'' ''See notes''
|2
|-
|23
|HW1071
|KEY-WOODRUFF-#808 STD
|
|
|2
|-
|24
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|8
|-
|25
|HW0107
|WASHER-LOCK-3/8"
|
|
|8
|-
|26
|H1547
|ADAPTER-#8 JICM X #10 SAEM
|
|
|4
|-
|27
|43017051
|SHIM-CASTER-1/2"
|
|''Used on Frame #'s 620 and up''
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Parts obsolete and no longer available. Spline Drive Conversion Kit PT# 80222003 required. Reuse of Bushing after disassembly NOT recommended.''
|}

==== ''<big>Discontinued Drive Wheel Assembly (November 2012 to November 2013)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Drive Wheel Assembly Used Nov 2012 to Nov 2013.png|alt=BE-SL & BE-DS Discontinued Drive Wheel Assembly (November 2012 to November 2013))|frameless|580x580px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43715012
|FRAME-FLOOR DRIVE
|
|
|2
|-
|2
|C0050-2
|WHEEL-8" X 3"-POLY
|80222001
|
|2
|-
|3
|PT0406
|FLANGE BEARING-4 BOLT-1 3/16"
|80222001
|''Alloy casting''
|4
|-
|4
|HW0504
|BOLT-HHCS-1/2-13 X 2"
|
|
|8
|-
|5
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|8
|-
|6
|HW0110
|WASHER-LOCK-1/2"
|
|
|24
|-
|7
|HW0007
|NUT-HEX-1/2-13
|
|
|24
|-
|8
|43797001
|ROD-THREADED-1/2-13 X 7"
|
|
|8
|-
|9
|43727007
|SPACER-DRIVE WHEEL
|
|''Must be ordered as a set of 4''
|8
|-
|10
|43727006
|PLATE-MOTOR MOUNTING
|
|
|2
|-
|11
|80222002
|SHAFT-WHEEL
|
|''†† Includes Coupling Body''
|2
|-
|12
|43097005
|KEY-1/4" X 3"
|80222001
|
|2
|-
|13
|N/A
|COUPLING BODY-TAPER BORE-#50
|
|''†'' ''See notes''
|2
|-
|14
|HW0323
|BOLT-HHCS-5/16-18 X 1"
|
|
|8
|-
|15
|PT0321
|CHAIN-COUPLING-#50
|
|''Includes Connecting Pin''
|2
|-
|16
|N/A
|BUSHING-TAPER LOCK-1"
|
|''†'' ''See notes''
|2
|-
|17
|N/A
|MOTOR-HYDRAULIC-160CC
|
|''†'' ''See notes''
|2
|-
|18
|HW1071
|KEY-WOODRUFF-#808 STD
|
|
|2
|-
|19
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|8
|-
|20
|HW0107
|WASHER-LOCK-3/8"
|
|
|8
|-
|21
|H1547
|ADAPTER-#8 JICM X #10 SAEM
|
|
|4
|-
|22
|HW1111
|RETAINING RING-1 3/16"
|
|''††'' ''Available in multiple kits''
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''†'' ''Parts obsolete and no longer available. Spline Drive Conversion Kit PT# 80222003 required. Reuse of Bushing after disassembly NOT recommended.''
|-
| colspan="6" |''†† Parts included in multiple kits''
|}

==== ''<big>Current Drive Wheel Assembly for BE-24 & BE-36 units (November 2013 to Present) & Discontinued Drive Wheel Assembly for BE-42 units (November 2013 to August 2021)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Current Drive Wheel Assembly BE-24 and BE-36 and Discontinued for BE-42 (used Nov 2013 to August 2021).png|alt=BE-SL & BE-DS Current Drive Wheel Assembly BE-24 and BE-36 and Discontinued for BE-42 (used Nov 2013 to August 2021)|frameless|579x579px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43722002-6B-1
|FLOOR DRIVE ASSEMBLY
|
|''Includes Items 1 through 19''
|2
|-
|1
|43715012
|FRAME-FLOOR DRIVE
|
|
|2
|-
|2
|C0050-2
|WHEEL-8" X 3"-POLY
|80222001
|
|2
|-
|3
|PT0406
|FLANGE BEARING-4 BOLT-1 3/16"
|80222001
|''Alloy casting''
|4
|-
|4
|HW0504
|BOLT-HHCS-1/2-13 X 2"
|
|
|8
|-
|5
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|8
|-
|6
|HW0110
|WASHER-LOCK-1/2"
|
|
|24
|-
|7
|HW0007
|NUT-HEX-1/2-13
|
|
|24
|-
|8
|43797001
|ROD-THREADED-1/2-13 X 7"
|
|
|8
|-
|9
|43727007
|SPACER-DRIVE WHEEL
|
|''Must be ordered as a set of 4''
|8
|-
|10
|43727006
|PLATE-MOTOR MOUNTING
|
|
|2
|-
|11
|80222002
|SHAFT-WHEEL
|†
|''Includes Coupling Body''
|2
|-
|12
|43097005
|KEY-1/4" X 3"
|80222001
|
|2
|-
|13
|PT0330
|COUPLING BODY-#50-SPLINE BORE
|80222003
|
|2
|-
|14
|PT0321
|CHAIN-COUPLING-#50
|
|''Includes Connecting Pin''
|2
|-
|15
|HC0120-6B-1
|MOTOR-HYDRAULIC-160CC
|80222003
|''Spline Shaft''
|2
|-
|16
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|8
|-
|17
|HW0107
|WASHER-LOCK-3/8"
|
|
|8
|-
|18
|HW1111
|RETAINING RING-1 3/16"
|†
|
|2
|-
|19
|H1547
|ADAPTER-#8 JICM X #10 SAEM
|
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Parts included in multiple kits.''
|}

==== ''<big>Current Radial Piston Drive Wheel Assembly for BE-42 units (August 2021 to Present)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Current Radial Piston Assembly for all BE-42 (shipped August 2021 to Present).png|alt=Current Radial Piston Assembly for all BE-42 (shipped August 2021 to Present)|frameless|548x548px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43822005
|RADIAL PISTON DRIVE WHEEL ASSEMBLY
|
|''Includes Items 1 through 6''
|2
|-
|1
|43825003
|RADIAL PISTON DRIVE WHEEL MOUNT
|
|
|1
|-
|2
|HC0160-1
|400CC RADIAL PISTON MOTOR
|
|''Includes Nuts & Studs''
|1
|-
|REF
|HC0160-STUD
|STUD-M14-1.5 X 46MM
|
|''Replacement Motor Stud''
|A/R
|-
|REF
|HC0160-NUT
|NUT-FLANGED HEX-M14-1.5
|
|''Replacement Motor Nut''
|A/R
|-
|3
|C0511
|WHEEL-POLY-10 X 5"-FLANGE MOUNT
|
|
|1
|-
|4
|HW0514
|BOLT-HHCS-1/2-13 X 2 1/2"
|
|
|6
|-
|5
|HW0110
|WASHER-LOCK-1/2"
|
|
|6
|-
|6
|HW0007
|NUT-HEX-1/2-13
|
|
|6
|-
|7
|H1612
|ADAPTER-H-90 DEG-#10 SAEM X #8 JICM
|
|
|2
|-
|8
|H1539
|ADAPTER-#8 JIC X #6 SAE
|
|
|1
|-
|9
|H1586
|ADAPTER-90 DEG-#8 JICSW X #6 NPT
|
|
|1
|-
|10
|H0801
|TEE-H-#6 NPT
|
|
|1
|-
|11
|H1501
|ADAPTER-#8 JIC X #6 NPT
|
|
|1
|-
|12
|H0200
|REDUCER-#6 NPT X #4 NPT
|
|
|1
|-
|13
|H0206
|PLUG-#4 NPT
|
|''† Left (LH) Drive Wheel only''
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Plug used on Left Drive Wheel Assembly only. Hose from Left Drive Wheel Assembly is connected to Tee on Right Drive Wheel Assembly.''
|}

=== <big>Idler Casters</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Idler Casters.png|alt=BE-SL & BE-DS Idler Casters|frameless|554x554px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|C0220-1
|CASTER-8" X 3"-POLY
|
|
|2
|-
|2
|43017022
|SHIM-CASTER-1/4"
|
|
|2
|-
|3
|43017051
|SHIM-CASTER-1/2"
|
|''Used on Frame #'s 620 and Up''
|2
|-
|4
|HW0517
|BOLT-HHCS-1/2-13 X 2 1/2"-FULL THREAD
|
|
|6
|-
|5
|HW0518
|BOLT-HHCS-1/2-13 X 3"-FULL THREAD
|
|''Cylinder Support Bracket Bolt''
|2
|-
|6
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|16
|-
|7
|HW0110
|WASHER-LOCK-1/2"
|
|
|8
|-
|8
|HW0007
|NUT-HEX-1/2-13
|
|
|8
|}

== <big>Electrical</big> ==

=== <big>AC Power Stanchion</big> ===

==== ''<big>BE-SL Aero-Motive Energy Rail</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL Aero-Motive Energy Rail.png|alt=BE-SL Aero-Motive Energy Rail|frameless|540x540px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43635001
|STANCHION-POWER
|
|''114" O.A.L.''
|1
|-
|2
|HW1030
|U-BOLT-3/8-16 X 2" X 5"
|
|''Square bend''
|3
|-
|3
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|6
|-
|4
|HW0107
|WASHER-LOCK-3/8"
|
|
|6
|-
|5
|HW0005
|NUT-HEX-3/8-16
|
|
|6
|-
|6
|46837014-2
|TOW ARM-COLLECTOR TROLLEY
|
|
|1
|-
|7
|46838015
|SPACER BLOCK-TOW ARM
|
|
|1
|-
|8
|E0632
|RESTRAINT-3/4"
|
|''Grip size .625" to .750"''
|1
|-
|9
|E0618
|LOCKNUT-CONDUIT-3/4"
|
|
|1
|-
|10
|E0612
|COVER-JUNCTION BOX
|
|''Included with Item 1''
|1
|-
|11
|HW1051
|EYE BOLT-3/16-16 X 5 1/2"
|
|
|2
|-
|12
|HW0126
|WASHER-FLAT-3/8"-FENDER
|
|
|4
|-
|13
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|14
|HW0005
|NUT-HEX-3/8-16
|
|
|4
|-
|15
|E1105
|JUNCTION BOX-4" X 2" X 2"
|
|''Weatherproof''
|1
|-
|16
|E1106
|COVER-JUNCTION BOX
|
|''Weatherproof with Gasket''
|1
|-
|17
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
|18
|E0608-1
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .450" to .560"''
|1
|-
|19
|E0622
|RESTRAINT-1/2"
|
|''Grip size.450" to .560"''
|1
|-
|20
|BD0010
|TROLLEY-ENERGY RAIL
|
| rowspan="2" |''Aero-Motive Rail only''

''(Orange housing color)''
|1
|-
|21
|BD0100
|BRUSH-TROLLEY
|
|4
|}

==== ''<big>BE-DS Aero-Motive Energy Rail</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-DS Aero-Motive Energy Rail.png|alt=BE-DS Aero-Motive Energy Rail|frameless|553x553px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43735001
|STANCHION-POWER
|
|
|1
|-
|2
|HW1030
|U-BOLT-3/8-16 X 2" X 5"
|
|''Square bend''
|3
|-
|3
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|6
|-
|4
|HW0107
|WASHER-LOCK-3/8"
|
|
|6
|-
|5
|HW0005
|NUT-HEX-3/8-16
|
|
|6
|-
|6
|46837014-2
|TOW ARM-COLLECTOR TROLLEY
|
|
|1
|-
|7
|46838015
|SPACER BLOCK-TOW ARM
|
|
|1
|-
|8
|E0632
|RESTRAINT-3/4"
|
|''Grip size .625" to .750"''
|1
|-
|9
|E0618
|LOCKNUT-CONDUIT-3/4"
|
|
|1
|-
|10
|E0612
|COVER-JUNCTION BOX
|
|''Included with Item 1''
|1
|-
|11
|HW1051
|EYE BOLT-3/16-16 X 5 1/2"
|
|
|2
|-
|12
|HW0126
|WASHER-FLAT-3/8"-FENDER
|
|
|4
|-
|13
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|14
|HW0005
|NUT-HEX-3/8-16
|
|
|4
|-
|15
|E1105
|JUNCTION BOX-4" X 2" X 2"
|
|''Weatherproof''
|1
|-
|16
|E1106
|COVER-JUNCTION BOX
|
|''Weatherproof with Gasket''
|1
|-
|17
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
|18
|E0608-1
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .450" to .560"''
|1
|-
|19
|E0622
|RESTRAINT-1/2"
|
|''Grip size.450" to .560"''
|1
|-
|20
|BD0010
|TROLLEY-ENERGY RAIL
|
| rowspan="2" |''Aero-Motive Rail only''

''(Orange housing color)''
|1
|-
|21
|BD0100
|BRUSH-TROLLEY
|
|4
|}

==== ''<big>Vahle Energy Rail</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Vahle Energy Rail.png|alt=BE-SL & BE-DS Vahle Energy Rail|frameless|555x555px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1A
|BD0031
|TROLLEY-ENERGY RAIL, KSL
|
| rowspan="3" |''† Vahle KSL Rail only''

''(Green housing color)''
|1
|-
|2A
|BD0040
|BRUSH-PHASE, KSL
|
|3
|-
|3A
|BD0041
|BRUSH-GROUND, KSL
|
|1
|-
|1B
|BD0231
|TROLLEY-ENERGY RAIL, KBH
|
| rowspan="3" |''† Vahle KBH Rail only''

''(Gray housing color)''

''(Not shown)''
|1
|-
|2B
|BD0240
|BRUSH-PHASE, KBH
|
|3
|-
|3B
|BD0241
|BRUSH-GROUND, KBH
|
|1
|-
| rowspan="2" |4
|BD0030
|TOW ARM-COLLECTOR TROLLEY, KSL
|
|''†'' ''Vahle KSL Rail only''

''(Green housing color)''
|1
|-
|BD0230
|TOW ARM-COLLECTOR TROLLEY, KBH
|
|''†'' ''Vahle KBH Rail only''

''(Gray housing color)''
|1
|-
|5
|46838015
|SPACER-BLOCK-TOW ARM
|
|''†† See notes''
|1
|-
|6
|41237083-2
|BRACKET-TOW ARM
|
|''††'' ''See notes''
|1
|-
|7
|HW1054
|U-BOLT-5/16-18 X 2" X 5"-SQUARE BEND
|
|
|1
|-
|8
|HW0323
|BOLT-HHCS-5/16-18 X 1"
|
|
|2
|-
|9
|HW0106
|WASHER-FLAT-5/16"-SAE
|
|
|4
|-
|10
|HW0150
|WASHER-FLAT-5/16"-FENDER
|
|
|2
|-
|11
|HW0105
|WASHER-LOCK-5/16"
|
|
|4
|-
|12
|HW0004
|NUT-HEX-5/16-18
|
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Verify Energy Rail Type (KSL or KBH) by the color of the Energy Rail Housing.''
|-
| colspan="6" |''†† Not all units equipped with Tow Arm Bracket. Location of Spacer Block and/or Tow Arm Bracket may vary from configuration shown.''
|}

=== <big>Transformer & Magnet Starter</big> ===

==== <big>''Magnet Starter''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Magnet Starter.png|alt=BE-SL & BE-DS Magnet Starter|frameless|555x555px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0103
|MAGNETIC STARTER
|
|''NEMA 1''
|1
|-
|2
|E0608-1
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .450" to .560"''
|1
|-
|3
|E0623
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .250" to .375"''
|4
|-
|4
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|1
|-
|5
|E0622
|RESTRAINT-1/2"
|
|''Grip size .450" to .560"''
|1
|-
|6
|E0613
|RESTRAINT-3/4"
|
|''Grip size .500" to .625"''
|1
|-
|7
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|7
|-
|8
|E0618
|LOCKNUT-CONDUIT-3/4"
|
|
|1
|-
|9
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|3
|-
|10
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|7
|-
|11
|HW0103
|WASHER-LOCK-1/4'
|
|
|3
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|}

==== ''<big>Transformer</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Transformer.png|alt=BE-SL & BE-DS Transformer|frameless|537x537px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="2" |1
|80232002
|TRANSFORMER-480V:120V-1.5 KVA
|
|''†'' ''See notes''
|1
|-
|E0220
|TRANSFORMER-480V:120V-3.0 KVA
|
|''††'' ''See notes''
|1
|-
|2
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|2
|-
|3
|E0617
|LOCKNUT-CONDUIT-1/2
|
|''(Not shown)''
|2
|-
|4
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|5
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|8
|-
|6
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|7
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|8
|00196401
|LABEL-DANGER-480V
|
|''(Not shown)''
|1
|-
|9
|00196408
|LABEL-DANGER-DISCONNECT POWER
|
|''(Not shown)''
|1
|-
! colspan="6" |NOTE
|-
| colspan="6" |''† 1.5 Kva Transformer used on units shipped prior to February 2020.''
|-
| colspan="6" |''†† 3.0 Kva Transformer used on units shipped 2020 to Present.''
|-
| colspan="6" |''Verify Transformer rating prior to ordering replacement.''
|}

=== <big>Operator Console</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Operator Console Parts.png|alt=BE-SL & BE-DS Operator Console Parts Diagram|frameless|544x544px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0327
|KEYED ACTUATOR ASSEMBLY
|
|''Includes 2 Keys & Contact Block''
|1
|-
|2
|E0351
|KEY-REPLACEMENT
|
|''Set of 2 Keys''
|A/R
|-
|3
|E0309-1
|HOUR METER
|
|''† Includes Mounting Hardware''
|1
|-
|4
|N/A
|SWITCH-SELECTOR-3 POSITION
|
|''ON-OFF-ON, †† See notes''
|1
|-
| rowspan="2" |5
|N/A
|LEGEND PLATE-VACUUM
|
|''†††'' ''See notes''
|1
|-
|N/A
|LEGEND PLATE-MAGNET
|
|''†††'' ''See notes''
|1
|-
|6
|N/A
|CONTACT BLOCK-N/O
|
|''††'' ''See notes''
|2
|-
|7
|N/A
|CONTACT BLOCK-N/C
|
|''††'' ''See notes''
|2
|-
|8
|E1083
|SWITCH-SELECTOR-3 POSITION
|80232001
|''OFF-ON-OFF''
|1
|-
|9
|E1080
|CONTACT BLOCK-N/O & N/C
|80232001
|
|2
|-
|10
|YE0311
|SWITCH-EMERGENCY STOP
|
|
|1
|-
|11
|YE0407
|LEGEND PLATE-EMERGENCY STOP
|
|
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Current hour meter is 3-Bolt version. Replacement of 4-Bolt version will require new mounting holes to be drilled in Dashboard.''
|-
| colspan="6" |''†† Parts no longer available. Must order new Selector Switch Kit 80232001.''
|-
| colspan="6" |''††† Parts no longer available. See [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#BE-SL_Labels BE-SL Labels] and [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#BE-DS_Labels BE-DS Labels] sections for current Placards.''
|}

=== <big>Switches</big> ===

==== ''<big>Foot Switch</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Foot Switch.png|alt=BE-SL & BE-DS Foot Switches|frameless|726x726px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0301-1
|SWITCH-FOOT OPERATED
|
|''†'' ''See notes''
|1
|-
|2
|E0613
|RESTRAINT-3/4"
|
|''Grip size .500" to .625"''
|1
|-
|3
|E0515
|CORD-14-3-SO/SOW
|
|
|9'
|-
|4
|HC0303
|BOLT-HHCS-1/4-20 X 1"
|
|''If equipped''
|2
|-
|5
|HC0103
|WASHER-1/4"-LOCK
|
|''If equipped''
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Open-Style Switch is a direct replacement for discontinued, Covered-Style Switch.''
|}

==== ''<big>Gate Switch</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Gate Switch.png|alt=BE-SL & BE-DS Gate Switches|frameless|549x549px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0312
|SWITCH-PUSH BUTTON
|
|
|1
|-
|2
|43017041
|MOUNT-GATE SWITCH
|
|
|1
|-
|3
|HW1077
|SCREW-RHMS-#10-24 X 5/8"
|
|
|2
|-
|4
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|2
|-
|5
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|6
|HW0307
|BOLT-SHCS-1/4-20 X 1"
|
|
|2
|-
|7
|PL0502
|GROMMET-3/8" I.D.
|
|
|1
|-
|8
|YE0305
|SWITCH-ROLLER
|
|
|1
|-
|9
|SS0303
|WASHER-FLAT-#8
|
|
|2
|-
|10
|SS0111
|SCREW-SHCS-#8-32 X 1 1/2"
|
|
|2
|-
|11
|SS0203
|NUT-NILN-#8-32
|
|''Used on BE-DS only''
|2
|-
|12
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|1
|}

==== ''<big>Proximity Switch</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Proximity Switch.png|alt=BE-SL & BE-DS Proximity Switch|frameless|533x533px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0314
|SENSOR-PROXIMITY-30MM
|
|
|1
|-
|2
|43017027-2
|BRACKET-PROXIMITY SENSOR
|
|
|1
|-
|3
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|2
|-
|4
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|5
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|-
| rowspan="2" |6
|43017037-2
|ANGLE-PROXIMITY SENSOR TARGET
|
|''Rotary Actuator units''
|1
|-
|43017084-2
|ANGLE-PROXIMITY SENSOR TARGET
|
|''Helical Actuator units''
|1
|-
|7
|HW0311
|BOLT-FHSCS-1/4-20 X 3/4"
|
|
|2
|}

=== <big>Junction Boxes</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Junction Box Diagram.png|alt=BE-SL & BE-DS Junction Box |frameless|554x554px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0611
|JUNCTION BOX-4" X 2" X 2"
|
|
|2
|-
|2
|E0612
|COVER-JUNCTION BOX
|
|
|2
|-
|3
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|4
|-
|4
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|6
|-
|5
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|6
|}

=== <big>Fusing</big> ===

==== <big>''Primary Fusing (June 2007 to Present)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Primary Fusing.png|alt=BE-SL & BE-DS Primary Fusing (Effective June 2207 to Present)|frameless|550x550px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43036001
|JUNCTION BOX-4" X 4" X 2"
|
|''Includes Cover''
|1
|-
|2
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|2
|-
|3
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|2
|-
|4
|HW0301
|BOLT-HHCS-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
|5
|E1131
|FUSE HOLDER
|
|
|2
|-
|6
|HW0135
|SCREW-RHMS-#8-32 X 3/4"
|
|
|4
|-
|7
|HW0132
|NUT-NILN-#8-32
|
|
|4
|-
|8
|X350057
|FUSE-4 AMP
|
|
|2
|}

==== <big>''Secondary Fusing''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Secondary Fusing.png|alt=BE-SL & BE-DS Secondary Fusing|frameless|571x571px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0323
|FUSE HOLDER
|
|
|1
|-
|2
|E0914
|FUSE-10 AMP
|
|
|1
|-
|3
|HW0130
|SCREW-RHMS-#8-32 X 1/2"
|
|
|2
|-
|4
|E0132
|NUT-NILN-#8-32
|
|''(Not shown)''
|2
|-
|5
|43096008
|LEGEND PLATE "...10 AMP FUSE..."
|
|''(Not shown)''
|1
|}

=== <big>120V Receptacle</big> ===
[[File:IOP-400 BE-SL&DS (10-23) 120V Receptacle.png|alt=BE-SL & BE-DS 120V Receptacle|frameless|539x539px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0611
|JUNCTION BOX-4" X 2" X 2"
|
|
|1
|-
|2
|E0622
|RESTRAINT-1/2"
|
|''Grip size .450" to .560"''
|1
|-
|3
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|1
|-
|4
|E0650
|RECEPTACLE-DUPLEX
|
|''†20A''
|1
|-
|5
|E0651
|COVER-RECEPTACLE-DUPLEX
|
|
|1
|-
|6
|E0655
|RECEPTACLE-GFCI
|
|''20A''
|1
|-
|7
|E0656
|COVER-RECEPTACLE-GFCI
|
|
|1
|-
|8
|E0654
|JUNCTION BOX-4" X 4" X 2"
|
|
|1
|-
|9
|E0657
|COVER-RECEPTACLE-DUPLEX/GFCI
|
|
|1
|-
|10
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|''Mounting Hardware (Not shown)''
|A/R
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† If Duplex Receptacle has Split Feed (1 set of black and white wires for each plug), the Break-Off Fin must be removed prior to installation.''
|}

=== <big>Wiring Diagrams & Schematics</big> ===

==== '''<big>''BE-SL & BE-DS Electrical Schematic''</big>''' ====
[[File:IOP-400 BE-SL&DS (10-23) Wiring Diagram 1.png|alt=BE-SL & BE-DS Electrical Schematic|frameless|900x900px]]

==== '''<big>''[Discontinued] BE-SL & BE-DS with Water Cart Wiring Diagram (Prior to October 10, 2012)''</big>''' ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued BE-SL and BE-DS with Water Cart Wiring Diagram.png|alt=Discontinued BE-SL and BE-DS with Water Cart Wiring Diagram|frameless|900x900px]]

==== '''<big>''[Current] BE-SL & BE-DS with Auxiliary Receptacle Wiring Diagram (October 10, 2012 to Present)''</big>''' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL and BE-DS with Auxiliary Receptacle Wiring Diagram.png|alt=Current BE-SL and BE-DS with Auxiliary Receptacle Wiring Diagram|frameless|897x897px]]

'''<big>''BE-SL & BE-DS Magnet Extraction Wiring Diagram''</big>'''

[[File:IOP-400 BE-SL&DS (10-23) BE-SL & BE-DS with Magnet Wiring Diagram.png|alt=BE-SL and BE-DS with Magnet Wiring Diagram|frameless|897x897px]]

== <big>Hydraulics</big> ==

=== <big>Power Unit & Riser</big> ===

==== <big>''Power Unit''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL and BE-DS Power Unit.png|alt=BE-SL & BE-DS Power Unit|frameless|547x547px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0003
|MOTOR-ELECTRIC-5 HP
|
|
|1
|-
|2
|HC0305
|ADAPTER
|
|''Pump-to-Motor''
|1
|-
|3
|HC0319
|PUMP-VARIABLE DISPLACEMENT-7.5 GPM
|
|''Vane Type''
|1
|-
|4
|HC0313
|COUPLING BODY-1 1/8"
|
|''Motor end''
|1
|-
|5
|HC0312
|SPIDER-COUPLING INSERT
|
|
|1
|-
|6
|HC0311
|COUPLING BODY-3/4"
|
|''Pump end''
|1
|-
|7
|H1606
|ADAPTER-90 DEG-#8 JICM X #8 SAEM
|
|
|1
|-
|8
|H1603
|ADAPTER-90 DEG-#16 JICM X #16 SAEM
|
|
|1
|-
|9
|H1650
|BUSHING-RED-#12 SAEM X #8 SAEF
|
|
|1
|-
|10
|H1538
|UNION-#8 SAE
|
|
|1
|-
|11
|HC0261
|VALVE-MAIN SYSTEM PRESSURE
|
|
|1
|-
|11a
|43646004
|REPLACEMENT CARTRIDGE
|
|''† For Item 11 (Not shown)''
|A/R
|-
|12
|HC0318
|GAUGE-PRESSURE
|
|''0-3000 LBS''
|1
|-
|13
|H0206
|PLUG-#4 NPT
|
|
|1
|-
|14
|H1551
|ADAPTER-#12 JICM X #8 SAEM
|
|
|1
|-
|15
|H1540
|ADAPTER-#8 JICM X #8 SAEM
|
|
|1
|-
|16
|E0613
|RESTRAINT-3/4"
|
|''Grip size .500" to .625"''
|1
|-
|17
|E0618
|LOCKNUT-CONDUIT-3/4"
|
|''(Not shown)''
|1
|-
|18
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
| rowspan="4" |''Mounting Hardware (Not shown)''

''Used on all BE-SL''

''See [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Power_Unit_Riser Power Unit Riser] section for BE-DS Mounting Hardware''
|4
|-
|19
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|8
|-
|20
|HW0107
|WASHER-LOCK-3/8"
|
|4
|-
|21
|HW0005
|NUT-HEX-3/8-16
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Cartridges are for replacement only.''
|}

==== <big>''Power Unit Riser''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-DS Motor Riser.png|alt=BE-DS Motor Riser used on Frame #'s 368 to Present|frameless|617x617px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43717061-2
|RISER-MOTOR
|
|''Frames #'s 368 to Present''
|1
|-
|2
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
| rowspan="4" |''Mounting Hardware for BE-DS Frames #'s 367 and Earlier''
|4
|-
|3
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|8
|-
|4
|HW0107
|WASHER-LOCK-3/8"
|
|4
|-
|5
|HW0005
|NUT-HEX-3/8-16
|
|4
|-
|6
|HW0302
|BOLT-HHCS-1/4-20 X 3/4"
|
| rowspan="4" |''Mounting Hardware for BE-DS Frames #'s 368 to Present (Not shown)''
|4
|-
|7
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|8
|-
|8
|HW0103
|WASHER-LOCK-1/4"
|
|4
|-
|9
|HW0002
|NUT-HEX-1/4-20
|
|4
|}

=== <big>Reservoir</big> ===

==== <big>''BE-SL 18 Gallon Reservoir''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL 18 Gallon Reservoir.png|alt=BE-SL 18 Gallon Reservoir|frameless|543x543px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43642002
|RESERVOIR ASSEMBLY
|
|''† Includes Items 1 through 9''
|1
|-
|1
|HC0542
|GASKET-CHANNEL
|
|''Sold by length''
|8'
|-
|2
|HC0340
|GAUGE-SIGHT
|
|''With Thermometer''
|1
|-
|3
|HC0306
|STRAINER-SUCTION
|
|
|1
|-
|4
|HC0308
|FILLER/BREATHER ASSEMBLY
|
|''Includes Gaskets''
|1
|-
|5
|HW0209
|SCREW-RHMS-10-32 X 1/2"
|
|
|6
|-
|6
|BI0110
|ELBOW-STR-90 DEG-#16 NPT
|
|
|1
|-
|7
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|10
|-
|8
|BI0107
|ELBOW-STR-90 DEG-#12 NPT
|
|''† See notes''
|2
|-
|9
|H0208
|PLUG-#12 NPT
|
|
|1
|-
|10
|H1590
|ADAPTER-90 DEG-#16 JICM X #16 FNPT
|
|
|1
|-
|11
|BI0405
|CAP-#12 NPT
|
|
|1
|-
|12
|PB0311-1
|NIPPLE-#12 NPT X 2"-BRASS
|
|
|1
|-
|13
|HC0307
|RETURN LINE FILTER ASSEMBLY
|
|''Housing and Filter''
|1
|-
|14
|HC0317
|FILTER-RETURN LINE
|
|''Replacement Filter''
|1
|-
|15
|PB0310-1
|NIPPLE-CLOSE-#12 NPT-BRASS
|
|
|2
|-
|16
|BI0301
|TEE-#12 FNPT
|
|
|3
|-
|17
|H1502
|ADAPTER-#8 JICM X #12 NPTM
|
|
|3
|-
|18
|H1580
|ADAPTER-90 DEG-#8 JICM X #12 NPTM
|
|
|1
|-
|19
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
| rowspan="4" |''Mounting Hardware (Not shown)''
|4
|-
|20
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|8
|-
|21
|HW0107
|WASHER-LOCK-3/8"
|
|4
|-
|22
|HW0005
|NUT-HEX-3/8-16
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† One Elbow included with Reservoir Assembly.''
|}

==== <big>''[Current] BE-DS 18 Gallon Reservoir (February 2004 to Present)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Current BE-DS 18 Gallon Reservoir (February 2004 to Present).png|alt=Current BE-DS 18 Gallon Reservoir (February 2004 to Present)|frameless|540x540px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43642002
|RESERVOIR ASSEMBLY
|
|''†'' ''Includes Items 1 through 9''
|1
|-
|1
|HC0542
|GASKET-CHANNEL
|
|''Sold by length''
|8'
|-
|2
|HC0340
|GAUGE-SIGHT
|
|''With Thermometer''
|1
|-
|3
|HC0306
|STRAINER-SUCTION
|
|
|1
|-
|4
|HC0308
|FILLER/BREATHER ASSEMBLY
|
|''Includes Gaskets''
|1
|-
|5
|HW0209
|SCREW-RHMS-10-32 X 1/2"
|
|
|6
|-
|6
|BI0110
|ELBOW-STR-90 DEG-#16 NPT
|
|
|1
|-
|7
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|10
|-
|8
|BI0107
|ELBOW-STR-90 DEG-#12 NPT
|
|''†'' ''See notes''
|2
|-
|9
|H0208
|PLUG-#12 NPT
|
|
|1
|-
|10
|H1590
|ADAPTER-90 DEG-#16 JICM X #16 FNPT
|
|
|1
|-
|11
|BI0102
|ELBOW-90 DEG-#12 NPT
|
|
|3
|-
|12
|PB0311-1
|NIPPLE-#12 NPT X 2"-BRASS
|
|
|1
|-
|13
|HC0307
|RETURN LINE FILTER ASSEMBLY
|
|''Housing and Filter''
|1
|-
|14
|HC0317
|FILTER-RETURN LINE
|
|''Replacement Filter''
|1
|-
|15
|PB0310-1
|NIPPLE-CLOSE-#12 NPT-BRASS
|
|
|3
|-
|16
|BI0301
|TEE-#12 FNPT
|
|
|2
|-
|17
|H1502
|ADAPTER-#8 JICM X #12 NPTM
|
|
|4
|-
|18
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
| rowspan="4" |''Mounting Hardware (Not shown)''
|4
|-
|19
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|8
|-
|20
|HW0107
|WASHER-LOCK-3/8"
|
|4
|-
|21
|HW0005
|NUT-HEX-3/8-16
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''†'' ''One Elbow included with Reservoir Assembly.''
|}

==== <big>''[Discontinued] BE-DS 10 Gallon Reservoir (Prior to February 2004)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued BE-DS 10 Gallon Reservoir (Prior to February 2004).png|alt=Discontinued BE-DS 10 Gallon Reservoir (Prior to February 2004)|frameless|563x563px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43742001
|RESERVOIR ASSEMBLY
|
|''Includes Items 1 through 8''
|1
|-
|1
|HC0542
|GASKET-CHANNEL
|
|''Sold by length''
|7'
|-
|2
|HC0340
|GAUGE-SIGHT
|
|''With Thermometer''
|1
|-
|3
|HC0306
|STRAINER-SUCTION
|
|
|1
|-
|4
|HC0308
|FILLER/BREATHER ASSEMBLY
|
|''Includes Gaskets''
|1
|-
|5
|HW0209
|SCREW-RHMS-10-32 X 1/2"
|
|
|6
|-
|6
|BI0110
|ELBOW-STR-90 DEG-#16 NPT
|
|
|1
|-
|7
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|10
|-
|8
|H0208
|PLUG-#12 NPT
|
|
|1
|-
|9
|H1590
|ADAPTER-90 DEG-#16 JICM X #16 FNPT
|
|
|1
|-
|10
|BI0102
|ELBOW-90 DEG-#12 NPT
|
|
|2
|-
|11
|BI0020
|NIPPLE-#12 NPT X 3"
|
|
|1
|-
|12
|HC0307
|RETURN LINE FILTER ASSEMBLY
|
|''Housing and Filter''
|1
|-
|13
|HC0317
|FILTER-RETURN LINE
|
|''Replacement Filter''
|1
|-
|14
|PB0310-1
|NIPPLE-CLOSE-#12 NPT-BRASS
|
|
|2
|-
|15
|BI0301
|TEE-#12 FNPT
|
|
|3
|-
|16
|H1509
|ADAPTER-#10 JICM X #12 NPTM
|
|
|2
|-
|17
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
| rowspan="4" |''Mounting Hardware (Not shown)''
|4
|-
|18
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|8
|-
|19
|HW0107
|WASHER-LOCK-3/8"
|
|4
|-
|20
|HW0005
|NUT-HEX-3/8-16
|
|4
|}

==== <big>''[Discontinued] BE-DS Heat Exchanger (Frame #'s 367 and Earlier)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued BE-DS Heat Exchanger (Frame - 367 and Earlier).png|alt=Discontinued BE-DS Heat Exchanger (Frame # 367 and Earlier)|frameless|566x566px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0503
|HEAT EXCHANGER
|
|
|1
|-
|2
|BI0107
|ELBOW-STR-90 DEG-#12 NPT
|
|
|2
|-
|3
|H1509
|ADAPTER-#10 JICM X #12 NPTM
|
|
|1
|-
|4
|BI0002
|NIPPLE-CLOSE-#12 NPT
|
|
|1
|-
|5
|BI0105
|ELBOW-RED-90 DEG-#12 FNPT X #8 FNPT
|
|
|1
|-
|6
|BI0001
|NIPPLE-CLOSE-#8 NPT
|
|
|1
|-
|7
|BI0101
|ELBOW-90 DEG-#8 FNPT
|
|
|1
|-
|8
|BI0004
|NIPPLE-#8 NPT X 3"
|
|
|1
|-
|9
|BI0302
|TEE-#8 FNPT
|
|
|1
|-
|10
|H1507
|ADAPTER-#8 JICM X # 8 NPTM
|
|
|2
|-
|11
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|4
|-
|12
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|8
|-
|13
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|14
|HW0005
|NUT-HEX-3/8-16
|
|
|4
|}

=== <big>Control Valve Assemblies</big> ===

==== <big>''Lift / Floor Drive / Arm Rotation Valve & Manifold Detail''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Lift + Floor Drive + Arm Rotation Valve & Manifold Detail.png|alt=BE-SL & BE-DS Lift / Floor Drive / Arm Rotation Valve & Manifold Detail|frameless|551x551px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0233
|VALVE-LEVER
|
|
|3
|-
|2
|HC0250
|MANIFOLD
|
|''3-Bank''
|1
|-
|3
|H1545
|ADAPTER-#10 JICM X #10 SAEM
|
|
|3
|-
|4
|H1641
|PLUG-#10 SAE
|
|
|1
|-
|5
|H1640
|PLUG-#6 SAE
|
|
|1
|-
|6
|H1606
|ADAPTER-90 DEG-#8 JICM X #8 SAEM
|
|
|2
|-
|7
|H1602
|ADAPTER-90 DEG-#8 JICM X #8 SAEM-LL
|
|
|2
|-
|8
|H1600
|ADAPTER-90 DEG-#6 JICM X #8 SAEM
|
|
|2
|-
|9
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|4
|-
|10
|H1587
|ADAPTER-#6 JICSW X #4 NPTM
|
|
|2
|-
|11
|HC0211
|VALVE-ADJUSTABLE FLOW CONTROL
|
|
|2
|-
|12
|H1504
|ADAPTER-#6 JICM X #4 NPTM
|
|
|2
|}

==== <big>''Rollers / Arm Traverse Valve & Manifold Detail''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Rollers + Arm Traverse Valve & Manifold Detaill.png|alt=BE-SL & BE-DS Rollers / Arm Traverse Valve & Manifold Detail|frameless|542x542px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0233
|VALVE-LEVER
|
|
|3
|-
|2
|HC0250
|MANIFOLD
|
|''3-Bank''
|1
|-
|3
|H1641
|PLUG-#10 SAE
|
|
|1
|-
|4
|H1610
|ADAPTER-90 DEG-#10 JICM X #10 SAEM
|
|
|2
|-
|5
|H1640
|PLUG-#6 SAE
|
|
|1
|-
|6
|H1000
|ADAPTER-#8 SAEM X #4 FNPT
|
|
|6
|-
|7
|H0001
|NIPPLE-#4 NPT
|
|
|4
|-
|8
|HC0247
|FIXED FLOW REGULATOR-2.25 GPM
|
|''†'' ''See notes''
|4
|-
|9
|H1504
|ADAPTER-#6 JICM X #4 NPTM
|
|
|6
|-
|10
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|4
|-
|11
|HC0233-SK
|SEAL KIT
|
|''For Item 1 (Not shown)''
|A/R
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Units built prior to January 2017 equipped with Adjustable Flow Controls. Fixed Flow Regulators are direct replacement for Adjustable Flow Controls.''
|}

=== <big>Lift Circuit</big> ===

==== <big>''Lift Cylinders''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL & BE-DS Lift Cylinders.png|alt=BE-SL & BE-DS Lift Cylinders|frameless|565x565px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="3" |1
|HC0403
|CYLINDER-LIFT, 2-1/2" X 20"
|
|''BE-SL only''
|4
|-
|HC0404
|CYLINDER-LIFT. 2-1/2" X 30"
|
|''BE-DS only. † See notes''
|4
|-
|HC0404-1
|CYLINDER-LIFT. 2-1/2" X 30"
|
|''BE-DS only. †† See notes''
|4
|-
|2
|H1578
|ADAPTER-#6 JICM X #6 NPTM
|
|
|4
|-
|3
|HC0426-1
|VELOCITY FUSE
|
|
|4
|-
|4
|H0302
|ELBOW-STR-90 DEG-#6 NPT
|
|
|4
|-
|5
|43722005
|CLEVIS ASSEMBLY
|
| rowspan="4" |''BE-DS only''
|4
|-
|6
|HW0407
|BOLT-HHCS-3/8-16 X 2 3/4"
|
|4
|-
|7
|HW0107
|WASHER-LOCK-3/8"
|
|4
|-
|8
|HW0005
|NUT-HEX-3/8-16
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† HC0404 valid for units shipped prior to December 2022.''
|-
| colspan="6" |''†† HC0404-1 valid for units shipped December 2022 to Present''
|}

==== <big>''[Current] Lift Circuit Configuration (Non-Interflow Manifold) [July 2003 to Present]''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Current Lift Circuit Configuration (Non-Interflow Manifold) (July 2003 to Present).png|alt=BE-SL & BE-DS Current Lift Circuit Configuration (Non-Interflow Manifold) [July 2003 to Present]|frameless|547x547px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0215
|VALVE-CHECK-CARTRIDGE
|
|
|8
|-
|2
|H1560
|ADAPTER-45 DEG-#8 JICM X #8 SAEM
|
|
|4
|-
|3
|H1670
|ADAPTER-45 DEG-#12 JICM X #10 SAEM
|
|
|1
|-
|4
|H1647
|ADAPTER-90 DEG-#10 SAEM X #8 FNPT
|
|
|1
|-
|5
|H0005
|NIPPLE-RED-#8 NPT X #6 NPT
|
|
|1
|-
|6
|HC0268
|VALVE-ADJUSTABLE FLOW CONTROL
|
|''Pressure compensated''
|1
|-
|7
|H1685
|ADAPTER-#10 JICM X #6 NPTM
|
|
|1
|-
|8
|H1690
|ADAPTER-#10 JICSW X #10 SAEM
|
|
|1
|-
|9
|H1612
|ADAPTER-90 DEG-#8 JICM X #10 SAEM
|
|
|1
|-
|10
|HC0282
|VALVE-COUNTER BALANCE
|
|
|1
|-
|10a
|43646005
|REPLACEMENT CARTRIDGE
|
|''† For Item 10 (Not shown)''
|A/R
|-
|11
|H1615
|ADAPTER-90 DEG-#6 JICM X #6 SAEM
|
|
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Cartridges are for replacement only.''
|}

==== <big>''[Current] Lift Circuit Configuration (Pilot-Down Manifold) [July 2003 to Present]''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Current Lift Circuit Configuration (Pilot-Down Manifold) (July 2003 to Present).png|alt=BE-SL & BE-DS Current Lift Circuit Configuration (Pilot-Down Manifold) [July 2003 to Present] |frameless|551x551px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43047002
|MANIFOLD-PILOT DOWN
|
|
|1
|-
|2
|H1501
|ADAPTER-#8 JICM X #6 NPTM
|
|
|2
|-
|3
|H1504
|ADAPTER-#6 JICM X #4 NPTM
|
|
|1
|-
|4
|H1579
|ADAPTER-90 DEG-#6 JICM X #4 NPTM
|
|
|2
|}

==== <big>''[Discontinued] Lift Circuit Configuration (Prior to July 2003)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Lift Circuit Configuration (Prior to July 2003).png|alt=BE-SL & BE-DS Discontinued Lift Circuit Configuration (Prior to July 2003)|frameless|521x521px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|H1501
|ADAPTER-#8 JICM X #6 NPTM
|
|
|1
|-
|2
|H1521
|ADAPTER-# 8 JICSW X #8 SAEM
|
|
|1
|-
|3
|HC0264
|VALVE-CHECK-PILOT TO OPEN
|
|
|1
|-
|4
|H1606
|ADAPTER-90 DEG-#8 JICM X #8 SAEM
|
|
|1
|-
|5
|H1621
|ADAPTER-#4 SAEM X #2 NPTM
|
|
|1
|-
|6
|HC0269
|VALVE-ADJUSTABLE FLOW CONTROL
|
|
|1
|-
|7
|H1591
|ADAPTER-90 DEG-#6 JICM X #2 NPTM
|
|
|1
|-
|8
|H1587
|ADAPTER-#6 JICSW X #4 NPTM
|
|
|1
|}

==== <big>''Lift Circuit Mounting''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL & BE-DS Lift Circuit Mounting.png|alt=BE-SL & BE-DS Lift Circuit Mounting|frameless|550x550px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43017014-2
|SUPPORT-MANIFOLD-PILOT DOWN
|
|
|1
|-
|2
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|2
|-
|3
|43718008
|STANDOFF
|
|
|1
|-
|4
|HW0315
|BOLT-HHCS-1/4-20 X 4 1/2"
|
|
|1
|-
|5
|HW0308
|BOLT-HHCS-1/4-20 X 2 1/2"
|
|
|2
|-
|6
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|10
|-
|7
|HW0103
|WASHER-LOCK-1/4"
|
|
|5
|-
|8
|HW0002
|NUT-HEX-1/4-20
|
|
|5
|}

=== <big>Floor Drive Circuit</big> ===

==== <big>''Cross Port Relief''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL & BE-DS Cross Port Relief.png|alt=BE-SL & BE-DS Cross Port Relief|frameless|554x554px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0262
|VALVE-CROSS PORT RELIEF
|
|
|1
|-
|1a
|43046002
|REPLACEMENT CARTRIDGE
|
|''† For Item 1 (Not shown)''
|A/R
|-
|2
|H1540
|ADAPTER-#8 JICM X #8 SAEM
|
|
|2
|-
|3
|H1646
|ADAPTER-90 DEG-#8 SAEM X #6 FNPT
|
|
|2
|-
|4
|H0805
|TEE-#6 NPTM
|
|
|2
|-
|5
|HC0272
|REGULATOR-FIXED FLOW
|
|''4.0 GPM''
|4
|-
|6
|H1566
|ADAPTER-45 DEG-#8 JICM X #6 NPTM
|
|
|2
|-
|7
|H1501
|ADAPTER-#8 JICM X #6 NPTM
|
|
|2
|-
|8
|HW0308
|BOLT-HHCS-1/4-20 X 2 1/2"
|
|
|2
|-
|9
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|10
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|11
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Cartridges are for replacement only.''
|}

==== <big>''Floor Drive Cutout''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL & BE-DS Floor Drive Cutout.png|alt=BE-SL & BE-DS Floor Drive Cutout|frameless|574x574px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|N/A
|SOLENOID-FLOOR DRIVE CUTOUT
|
|''†'' ''See notes''
|1
|-
|2
|H1540
|ADAPTER-#8 JICM X #8 SAEM
|
|
|1
|-
|3
|H1606
|ADAPTER-90 DEG-#8 JICM X #8 SAEM
|
|
|1
|-
|4
|BI0001
|NIPPLE-CLOSE-#8 NPT
|
|
|1
|-
|5
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|3
|-
|6
|E0611
|JUNCTION BOX-4" X 2" X 2"
|
|
|1
|-
|7
|E0612
|COVER-JUNCTION BOX
|
|
|1
|-
|8
|E0623
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .250" to .375"''
|A/R
|-
|9
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|A/R
|-
|10
|N/A
|SOLENOID-DRIVE CUTOUT
|
|''†'' ''See notes''
|1
|-
|11
|YE0501
|CONNECTOR-SOLENOID
|
|''DIN 43650''
|1
|-
|12
|43058004
|PLATE-SPACER
|
|
|1
|-
|13
|HC0278-SL/DS
|SOLENOID-DRIVE CUTOUT
|
|
|1
|-
|14
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|''For Item 6 (Not shown)''
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Part obsolete. Must be replaced with Retro Kit PT# 80242007.''
|}

==== <big>''Floor Drive Cutout Mounting''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL & BE-DS Floor Drive Cutout Mounting.png|alt=BE-SL & BE-DS Floor Drive Cutout Mounting|frameless|547x547px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HW0305
|BOLT-HHCS-1/4-20 X 2"
|
|
|2
|-
|2
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|3
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|4
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|-
|5
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
|6
|43058004
|PLATE-SPACER
|
|
|1
|}

=== <big>Counter Balance Valve</big> ===

==== <big>''[Discontinued] BE-SL Counter Balance Valve Configuration (Prior to January 2004)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued BE-SL Counter Balance Valve Configuration (Prior to January 2004).png|alt=Discontinued BE-SL Counter Balance Valve Configuration (Prior to January 2004)|frameless|531x531px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0263
|VALVE-COUNTER BALANCE
|
|
|1
|-
|1a
|43046004
|REPLACEMENT CARTRIDGE
|
|''For Item 1 (Not shown)''
|A/R
|-
|2
|H1552
|ADAPTER-#6 JICM X #6 SAEM
|
|
|2
|-
|3
|H1520
|ADAPTER-#6 JICSW X #6 SAEM
|
|
|2
|-
|4
|H1579
|ADAPTER-#6 JICM X #4 NPTM
|
|
|2
|-
|5
|HC0211
|VALVE-ADJUSTABLE FLOW CONTROL
|
|
|2
|-
|6
|H1565
|ADAPTER-45 DEG-#6 JICM X #4 NPTM
|
|
|2
|-
|7
|HW0305
|BOLT-HHCS-1/4-20 X 2"
|
|
|1
|-
|8
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|2
|-
|9
|HW0103
|WASHER-LOCK-1/4"
|
|
|1
|-
|10
|HW0002
|NUT-HEX-1/4-20
|
|
|1
|}

==== <big>''[Current] BE-SL Counter Balance Valve Configuration (January 2004 to Present)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Current BE-SL Counter Balance Valve Configuration (January 2004 to Present).png|alt= Current BE-SL Counter Balance Valve Configuration (January 2004 to Present)|frameless|543x543px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0263
|VALVE-COUNTER BALANCE
|
|
|1
|-
|1a
|43046004
|REPLACEMENT CARTRIDGE
|
|''For Item 1 (Not shown)''
|A/R
|-
|2
|H1552
|ADAPTER-#6 JICM X #6 SAEM
|
|
|2
|-
|3
|H1615
|ADAPTER-90 DEG-#6 JICM X #6 SAEM
|
|
|2
|-
|4
|HW0305
|BOLT-HHCS-1/4-20 X 2"
|
|
|2
|-
|5
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|6
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|7
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|}

==== <big>''[Discontinued] BE-DS Counter Balance Valve Configuration (Prior to January 2004)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued BE-DS Counter Balance Valve Configuration (Prior to January 2004).png|alt= Discontinued BE-DS Counter Balance Valve Configuration (Prior to January 2004)|frameless|575x575px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0263
|VALVE-COUNTER BALANCE
|
|
|1
|-
|1a
|43046004
|REPLACEMENT CARTRIDGE
|
|''† For Item 1 (Not shown)''
|A/R
|-
|2
|H1552
|ADAPTER-#6 JICM X #6 SAEM
|
|
|2
|-
|3
|H1520
|ADAPTER-#6 JICSW X #6 SAEM
|
|
|2
|-
|4
|H1579
|ADAPTER-#6 JICM X #4 NPTM
|
|
|2
|-
|5
|HC0211
|VALVE-ADJUSTABLE FLOW CONTROL
|
|
|2
|-
|6
|H1504
|ADAPTER-#6 JICM X #4 NPTM
|
|
|2
|-
|7
|HW0305
|BOLT-HHCS-1/4-20 X 2"
|
|
|2
|-
|8
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|9
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|10
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Cartridges are for replacement only.''
|}

==== <big>''[Current] BE-DS Counter Balance Valve Configuration (January 2004 to Present)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Current BE-DS Counter Balance Valve Configuration (January 2004 to Present).png|alt=Current BE-DS Counter Balance Valve Configuration (January 2004 to Present)|frameless|569x569px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0263
|VALVE-COUNTER BALANCE
|
|
|1
|-
|1a
|43046004
|REPLACEMENT CARTRIDGE
|
|''† For Item 1 (Not shown)''
|A/R
|-
|2
|H1552
|ADAPTER-#6 JICM X #6 SAEM
|
|
|2
|-
|3
|H1615
|ADAPTER-90 DEG-#6 JICM X #6 SAEM
|
|
|2
|-
|4
|HW0305
|BOLT-HHCS-1/4-20 X 2"
|
|
|2
|-
|5
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|6
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|7
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Cartridges are for replacement only.''
|}
=== <big>Miscellaneous Components</big> ===

==== ''<big>Transition Manifold</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23)Transition Manifolds.png|alt=BE-SL & BE-DS Transition Manifolds|frameless|543x543px]]
{| class="wikitable"
! colspan="6" |CURRENT CONFIGURATION (FRAME #'S 412 TO PRESENT)
|-
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43747002-2
|PLATE-TRANSITION
|
|
|1
|-
|2
|H0023
|NUT-BULKHEAD-#8 JIC
|
|
|4
|-
|3
|H0024
|UNION-BULKHEAD-#8 JICM
|
|
|4
|-
|4
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|2
|-
|5
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|6
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|7
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|}
{| class="wikitable"
! colspan="6" |DISCONTINUED CONFIGURATION (FRAME #'S 411 AND EARLIER)
|-
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43847003
|MANIFOLD-TRAVELING HOSE
|
|
|1
|-
|2
|43717054
|PLATE-MOUNTING
|
|
|1
|-
|3
|H1501
|ADAPTER-#8 JICM X #6 NPTM
|
|
|8
|-
|4
|HW0317
|BOLT-HHCS-1/4-20 X 3 1/2"
|
|
|2
|-
|5
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|6
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|7
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|}

=== <big>Equalization Chain Hose Guard</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Equalization Chain Hose Guard.png|alt=BE-SL & BE-DS Equalization Chain Hose Guard|frameless|622x622px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43017074-2
|GUARD-HOSE-EQ CHAIN
|
|''†'' ''See notes''
|1
|-
|2
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Used on units manufactured after May 2015.''
|}

=== <big>Hydraulic Schematics</big> ===

==== '''<big>''BE-SL& BE-DS Hydraulic Schematic''</big>''' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL & BE-DS Hydraulics Schematic.png|alt=BE-SL & BE-DS Hydraulics Schematic|frameless|900x900px]]

==== '''<big>''BE-DS with Heat Exchanger Hydraulic Schematic''</big>''' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-DS with Heat Exchanger Hydraulic Schematic.png|alt=BE-DS with Heat Exchanger Hydraulics Schematic|frameless|900x900px]]

==== '''<big>''BE-SL& BE-DS Extended Reach Hydraulic Schematic''</big>''' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL & BE-DS Extended Reach Hydraulic Schematic.png|alt= BE-SL & BE-DS Extended Reach Hydraulic Schematic|frameless|875x875px]]

== <big>Standard Available Options</big> ==

=== <big>Powered Roller Cutout (PRC)</big> ===

==== ''<big>Powered Roller Cutout Photo Eye Locations (Prior to August 2022)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Powered Roller Cutout Photo Eye Locations (Prior to August 2022).png|alt=BE-SL & BE-DS Powered Roller Cutout Photo Eye Locations (Prior to August 2022)|frameless|549x549px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E1321
|PHOTO EYE
|
|
|1
|-
|2
|41235057
|MOUNT-PHOTO EYE
|
|
|1
|-
|3
|HW0216
|SCREW-HHSC-#10-24 X 2"
|
|
|2
|-
|4
|HW0102
|WASHER-FLAT-#10-SAE
|
|
|2
|-
|5
|HW0032
|NUT-NILN-#10-24
|
|
|2
|-
|6
|HW0405
|BOLT-HHCS-3/8-16 X 2 "
|
|
|2
|-
|7
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|4
|-
|8
|HW0107
|WASHER-LOCK-3/8"
|
|
|2
|-
|9
|HW0005
|NUT-HEX-3/8-16
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''Quantities provided are for single-sided (PRC-1) Powered Roller Cutout option. For units with Double Sided (PRC-2) option, quantities are double.''
|-
| colspan="6" |''Configuration shown valid for units sold from November 2004 to Present. Consult the factory for units sold prior to November 1, 2004.''
|}

==== ''<big>Powered Roller Cutout Reflector Locations (Prior to August 2022)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Powered Roller Cutout Reflector Locations (Prior to August 2022).png|alt=BE-SL & BE-DS Powered Roller Cutout Reflector Locations (Prior to August 2022)|frameless|548x548px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E1321R
|REFLECTOR
|
|
|1
|-
|2
|41237013
|MOUNT-REFLECTOR
|
|
|1
|-
|3
|SS0803
|SCREW-RHMS-#6-32 X 5/8"
|
|
|2
|-
|4
|HW0405
|BOLT-HHCS-3/8-16 X 2 "
|
|
|2
|-
|5
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|4
|-
|6
|HW0107
|WASHER-LOCK-3/8"
|
|
|2
|-
|7
|HW0005
|NUT-HEX-3/8-16
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''Quantities provided are for single-sided (PRC-1) Powered Roller Cutout option. For units with Double Sided (PRC-2) option, quantities are double.''
|-
| colspan="6" |''Configuration shown valid for units sold from November 2004 to Present. Consult the factory for units sold prior to November 1, 2004.''
|}

==== ''<big>Powered Roller Cutout Photo Eye & Reflector Locations (August 2022 to Present)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Powered Roller Cutout Photo Eye & Reflector Locations (August 2022 to Present).png|alt=BE-SL & BE-DS Powered Roller Cutout Photo Eye & Reflector Locations (August 2022 to Present)|frameless|554x554px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E1321A
|PHOTO EYE
|
|''†'' ''Polarized''
|1
|-
|2
|41217170-2
|MOUNT-PHOTO EYE
|
|
|1
|-
|3
|HW0216
|SCREW-#10-24 X 2"
|
|''††'' ''See notes''
|2
|-
|4
|HW0032
|NUT-NILN-#10-24
|
|
|2
|-
|5
|E1321-R
|REFLECTOR
|
|
|1
|-
|6
|41217171
|MOUNT-REFLECTOR
|
|
|1
|-
|7
|SS0803
|SCREW-RHMS-#6-32 X 5/8"
|
|''††'' ''See notes''
|2
|-
|8
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|4
|-
|9
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|10
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|11
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''Quantities provided are for single-sided (PRC-1) Powered Roller Cutout option. For units with Double Sided (PRC-2) option, quantities are double.''
|-
| colspan="6" |''† Polarized Photo Eye recommneded to prevent potential operational issues with very smooth or shiny battery cases.''
|-
| colspan="6" |''†† Photo Eye & Reflector Mounting Screws are trimmed to length.''
|}

==== ''<big>Powered Roller Cutout Details</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Powered Roller Cutout Details.png|alt=BE-SL & BE-DS Powered Roller Cutout Details|frameless|528x528px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0281
|SOLENOID-POWER ROLLER CUTOUT
|
|
|2
|-
|2
|E0611
|JUNCTION BOX-4" X 2" X 2"
|
|
|1
|-
|3
|E0612
|COVER-JUNCTION BOX
|
|
|1
|-
|4
|BI0001
|NIPPLE-CLOSE-#8 NPT
|
|
|2
|-
|5
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|3
|-
|6
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|1
|-
|7
|H1600
|ADAPTER-90 DEG-#6 JICM X #8 SAEM
|
|
|3
|-
|8
|H1546
|ADAPTER-#6 JICM X #8 SAEM
|
|
|1
|-
|9
|41217089
|PLATE-MOUNTING-SOLENOID
|
|
|1
|-
|10
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|2
|-
|11
|HW0308
|BOLT-HHCS-1/4-20 X 2 1/2"
|
|
|2
|-
|12
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|13
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|14
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|15
|HW0143
|WASHER-FLAT-1/4"-FENDER
|
|''Used as Shims (Not shown)''
|A/R
|-
! colspan="6" |NOTES
|-
| colspan="6" |''Option configuration shown valid for units sold from November 2004 to Present. Consult the factory for units sold prior to November 1, 2004.''
|}

==== ''<big>Powered Roller Cutout Override Button</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Powered Roller Cutout Override Button.png|alt=BE-SL & BE-DS Powered Roller Cutout Override Button|frameless|579x579px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|N/A
|ACTUATOR-PUSH BUTTON (DISCONTINUED)
|
|''†'' ''See notes''
|1
|-
|2
|N/A
|CONTACT BLOCK-N/C (DISCONTINUED)
|
|''†'' ''See notes''
|1
|-
|3
|E0384
|ACTUATOR-PUSH BUTTON
|80932002
|
|1
|-
|4
|E0386
|CONTACT BLOCK-N/C
|80932002
|
|1
|-
|5
|E0387
|DUMMY BLOCK
|80932002
|
|1
|-
|6
|E0388
|PUSH BUTTON-GREEN
|80932002
|
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''Button location on dash may vary from position shown.''
|-
| colspan="6" |''† Parts no longer available. Must order new Push-Button Switch Kit 80932002.''
|}

==== ''<big>Powered Roller Cutout Junction Box</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Powered Roller Cutout Junction Box.png|alt=BE-SL & BE-DS Powered Roller Cutout Junction Box|frameless|527x527px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0611
|JUNCTION BOX-4" X 2" X 2"
|
|
|1
|-
|2
|E0612
|COVER-JUNCTION BOX
|
|
|1
|-
|3
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|3
|-
|4
|E0623
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .250" to .375"''
|1
|-
|5
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|4
|-
|6
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''Option configuration shown valid for units sold from November 2004 to Present. Consult the factory for units sold prior to November 1, 2004.''
|}

==== ''<big>Powered Roller Cutout Electrical Schematic</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Powered Roller Cutout Electrical Schematic.png|alt=BE-SL & BE-DS Powered Roller Cutout Electrical Schematic|frameless|900x900px]]

=== <big>Strobe Light & Audible Alarm</big> ===

==== <big>''Discontinued Strobe Light & Stanchion Configuration''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Strobe Light & Stanchion Configuration.png|alt=BE-SL & BE-DS Discontinued Strobe Light and Stanchion Configuration|frameless|770x770px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0317
|LIGHT-STROBE
|
|''110VAC''
|1
|-
|2
|41215014
|STANCHION-STROBE LIGHT
|
|
|1
|-
|3
|HW0402
|BOLT-HHCS-3/8-16 X 1
|
|
|3
|-
|4
|HW0107
|WASHER-LOCK-3/8
|
|
|3
|-
|5
|HW0108
|WASHER-FLAT-3/8-SAE
|
|
|3
|-
|6
|E1010
|CONNECTOR
|
|''Female (Not shown)''
|1
|-
|7
|E1011
|PLUG
|
|''Male (Not shown)''
|1
|}

==== <big>''Discontinued Audible Alarm Configuration''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Audible Alarm Configuration.png|alt=BE-SL & BE-DS Discontinued Audible Alarm Configuration|frameless|541x541px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0317-A
|ALARM-AUDIBLE
|
|
|1
|-
|2
|E0654
|JUNCTION BOX-4" X 4" X 2"
|
|
|1
|-
|3
|00117101-2
|MOUNT-AUDIBLE ALARM
|
|
|1
|-
|4
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|1
|-
|5
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|1
|-
|6
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|4
|}

==== <big>''Current Stack Light Strobe & Alarm Configuration''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Current Stack Light & Alarm Configuration.png|alt=BE-SL & BE-DS Current Stack Light & Alarm Configuration|frameless|860x860px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0362
|MOUNTING BASE
|
|''Includes restraints''
|1
|-
|2
|E0365
|TERMINAL BASE
|
|
|1
|-
|3
|E0363
|STROBE LIGHT-AMBER-120VAC
|
|''† See notes''
|1
|-
|4
|E0364
|AUDIBLE ALARM
|
|''††'' ''See notes''
|1
|-
|5
|SS0118
|SCREW-SHCS-#8-32 X 1"
|
|
|2
|-
|6
|SS0303
|WASHER-FLAT-#8
|
|
|2
|-
|7
|SS0203
|NUT-NILN-#8-32
|
|
|2
|-
|8
|E1010
|RECEPTACLE-TWIST LOCK
|
|''(Not shown)''
|1
|-
|9
|E1011
|PLUG-TWIST LOCK
|
|''(Not shown)''
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† For units equipped with the Audible Alarm option, a cap (Not shown) mounts on top of the Strobe Light in place of the Audible Alarm. Cap included with base.''

''†† For units equipped with the Strobe Light option, the Audible Alarm mounts directly to the terminal base in place of the Strobe Light.''
|}

==== <big>''Stack Light Strobe & Alarm Stanchion Mounting''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Stack Light Strobe & Alarm Stanchion Mounting.png|alt=BE-SL & BE-DS Stack Light Strobe & Alarm Stanchion Mounting|frameless|517x517px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41235060
|STACK LIGHT STANCHION
|
|''Discontinued''
|A/R
|-
|2
|HW0401
|BOLT-HHCS-3/8-16 X 1"
|
|
|3
|-
|3
|HW0107
|WASHER-LOCK-3/8"
|
|
|3
|-
|4
|HW0108
|WASHER-FLAT-3/8"
|
|
|3
|-
|REF
|43032006
|STANCHION ASSEMBLY
|
|''Includes Items 5 through 8''
|A/R
|-
|5
|43035003
|STACK LIGHT STANCHION
|
|
|1
|-
|6
|43037007-2
|CLAMP BRACKET
|
|
|1
|-
|7
|HW0305
|BOLT-HHCS-1/4-20 X 2"
|
|
|4
|-
|8
|HW0050
|NUT-FLANGED-1/4-20
|
|
|4
|-
|9
|43037004-2
|MOUNTING BRACKET
|
|''Overhead Guard only''
|1
|-
|10
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|}

=== <big>'''Horn'''</big> ===

==== ''<big>BE-SL Horn</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL Horn.png|alt=BE-SL Horn|frameless|543x543px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|YE0308
|BUTTON-HORN
|
|
|1
|-
|2
|E0317-A
|AUDIBLE ALARM
|
|
|1
|-
|3
|E0654
|JUNCTION BOX-4" X 4" X 2"
|
|
|1
|-
|4
|HW0302
|BOLT-HHCS-1/4-20 X 3/4"
|
|
|2
|-
|5
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|2
|-
|6
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|7
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|-
|8
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|1
|-
|9
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|1
|}

==== ''<big>BE-DS Horn</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-DS Horn.png|alt=BE-DS Horn|frameless|561x561px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|YE0308
|BUTTON-HORN
|
|
|1
|-
|2
|E0317-A
|AUDIBLE ALARM
|
|
|1
|-
|3
|E0654
|JUNCTION BOX-4" X 4" X 2"
|
|
|1
|-
|4
|HW0302
|BOLT-HHCS-1/4-20 X 3/4"
|
|
|2
|-
|5
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|2
|-
|6
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|7
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|-
|8
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|1
|-
|9
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|1
|}

=== <big>'''Overhead Guard'''</big> ===
[[File:IOP-400 BE-SL&DS (10-23) BE-DS Overhead Guard.png|alt=BE-SL & BE-DS Overhead Guard|frameless|570x570px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43715017
|OVERHEAD GUARD
|
|
|1
|-
|2
|HW0406
|BOLT-HHCS-3/8-16 X 2 1/2"
|
|
|4
|-
|3
|HW0108
|WASHER-FLAT-3/8"
|
|
|8
|-
|4
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|5
|HW0005
|NUT-HEX-3/8-16
|
|
|4
|}

=== <big>'''Operator Shield'''</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Operator Shield.png|alt=BE-SL & BE-DS Operator Shield|frameless|561x561px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43717116
|SHIELD-OPERATOR
|
|''†'' ''See notes''
|1
|-
|2
|43015010
|FRAME-OPERATOR SHIELD WELDMENT
|
|
|1
|-
|3
|43017066-2
|SUPPORT-SIDE
|
|
|2
|-
|4
|43017065-2
|SUPPORT-LOWER
|
|
|1
|-
|5
|43017067-2
|SUPPORT-UPPER
|
|
|1
|-
|6
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|16
|-
|7
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|32
|-
|8
|HW0103
|WASHER-LOCK-1/4"
|
|
|16
|-
|9
|HW0002
|NUT-HEX-1/4-20
|
|
|16
|-
|10
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|6
|-
! colspan="6" |
|-
| colspan="6" |''† Consult factory for units with Plexiglass bolted directly to frame.''
|}

=== <big>'''High Performance Options'''</big> ===

==== ''<big>Discontinued Outer Frame Guarding (Prior to December 2005)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Outer Frame Guarding.png|alt= BE-SL & BE-DS Discontinued Outer Frame Guarding|frameless|557x557px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41217010-2
|GUARD-FAR END-UPPER
|
|
|1
|-
|2
|41217036-2
|GUARD-FAR END-LOWER
|
|
|1
|-
|3
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|22
|}

==== ''<big>Discontinued Inner Frame Guarding (Prior to December 2005)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Inner Frame Guarding.png|alt=BE-SL & BE-DS Discontinued Inner Frame Guarding |frameless|564x564px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41217014-2
|GUARD-FRONT-OPERATOR CONSOLE
|
|
|1
|-
|2
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|4
|}

==== ''<big>Discontinued Cylinder Clamp Configuration (Prior to December 2005)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Cylinder Clamp Configuration.png|alt=BE-SL & BE-DS Discontinued Cylinder Clamp Configuration|frameless|530x530px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|00158001-22
|CHAIN-ROLLER-#80
|
|
|4
|-
|2
|3033T16
|CLAMP-CYLINDER
|
|
|4
|-
|3
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|4
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|5
|HW0143
|WASHER-FLAT-1/4"-FENDER
|
|
|12
|-
|6
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|7
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† See BE-DS Lift Cylinder Connections section for connecting links and mounting studs.''
|}

==== ''<big>Discontinued Lift Cylinder Configuration (Prior to December 2005)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Lift Cylinder Configuration.png|alt=BE-SL & BE-DS Discontinued Lift Cylinder Configuration|frameless|572x572px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43822006
|CLEVIS ASSEMBLY
|
|''Sold as Assembly only''
|4
|-
|2
|HW0813
|SCREW-SHSS-3/8-16 X 1/2"
|
|''Nylon tipped''
|8
|-
|3
|HC0427
|CYLINDER-LIFT
|
|
|4
|-
|4
|H1615
|ADAPTER-90 DEG-#6 JICM X #6 SAEM
|
|
|4
|-
|5
|HC0426-1
|VELOCITY FUSE
|
|
|4
|-
|6
|H0302
|ELBOW-STR-90 DEG-#6 NPT
|
|
|4
|}

==== ''<big>Current Lift Cylinder Configuration (December 2005 to Present)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Current Lift Cylinder Configuration.png|alt=BE-SL & BE-DS Current Lift Cylinder Configuration|frameless|734x734px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43722001
|CLEVIS ASSEMBLY
|
|''Sold as Assembly only''
|4
|-
|2
|HW0407
|BOLT-HHCS-3/8-16 X 2 3/4"
|
|
|4
|-
|3
|HC0404
|CYLINDER-LIFT
|
|''BS-DS-HP units only''
|4
|-
|4
|H1578
|ADAPTER-90 DEG-#6 JICM X #6 NPTM
|
|
|4
|-
|5
|HC0425
|VELOCITY FUSE
|
|
|4
|-
|6
|H0307
|ADAPTER-90 DEG-#6 NPTM X #8 FNPT
|
|
|4
|-
|7
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|8
|HW0005
|NUT-HEX-3/8-16
|
|
|4
|}

==== ''<big>Discontinued Floor Drive Assembly (Prior to December 2005)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Floor Drive Assembly.png|alt=BE-SL & BE-DS Discontinued Floor Drive Assembly|frameless|551x551px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43722003
|H.P. DRIVE WHEEL ASSEMBLY
|
|
|2
|-
|1
|HC0130
|MOTOR-HYDRAULIC-125CC
|
|
|2
|-
|2
|HW1071
|KEY-WOODRUFF-#808 STANDARD
|
|''Included with Item 1''
|A/R
|}

==== ''<big>Discontinued Pump & Motor Configuration (Prior to December 2005)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued High Performance Pump and Motor Configuration.png|alt=BE-SL & BE-DS Discontinued High Performance Pump and Motor Configuration|frameless|549x549px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0012
|MOTOR-ELECTRIC-7 1/2 HP
|
|
|1
|-
|2
|HC0332
|ADAPTER
|
|''Pump-to-Motor''
|1
|-
|3
|HC0327
|COUPLING-BODY-1 3/8"
|
|''Motor end''
|1
|-
|4
|HC0329
|SPIDER-COUPLING INSERT
|
|
|1
|-
|5
|HC0333
|COUPLING BODY-3/4"
|
|''Pump end''
|1
|-
|6
|HC0277
|SNUBBER-PRESSURE
|
|
|1
|-
|7
|E0613
|RESTRAINT-3/4"
|
|''Grip size .500" to .625"''
|1
|-
|8
|E0618
|LOCKNUT-CONDUIT-3/4"
|
|''(Not shown)''
|1
|}

==== ''<big>Current Pump & Motor Configuration (December 2005 to Present)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Current High Performance Pump and Motor Configuration.png|alt=BE-SL & BE-DS Current High Performance Pump and Motor Configuration|frameless|556x556px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0012
|MOTOR-ELECTRIC-7 1/2 HP
|
|
|1
|-
|2
|HC0326
|ADAPTER
|
|''Pump-to-Motor''
|1
|-
|3
|HC0355
|PUMP-VARIABLE DISPLACEMENT-12 GPM
|
|''Vane type''
|1
|-
|4
|HC0327
|COUPLING BODY-1 3/8"
|
|''Motor end''
|1
|-
|5
|HC0329
|SPIDER-COUPLING INSERT
|
|
|1
|-
|6
|HC0328
|COUPLING BODY-7/8"
|
|''Pump end''
|1
|-
|7
|HW0502
|BOLT-HHCS-1/2-13 X 1 1/4"
|
|
|2
|-
|8
|HW0110
|WASHER-LOCK-1/2"
|
|
|2
|-
|9
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|2
|-
|10
|H1606
|ADAPTER-90 DEG-#8 JICM X #8 SAEM
|
|
|1
|-
|11
|H1549
|ADAPTER-#20 JICM X #24 SAEM
|
|
|1
|-
|12
|H1595
|ADAPTER-90 DEG-#20 JICM X 20 JICSW
|
|
|1
|-
|13
|H1609
|ADAPTER-90 DEG-#12 JICM X #16 SAEM
|
|
|1
|-
|14
|E0613
|RESTRAINT-3/4"
|
|''Grip size .500" to .625"''
|1
|-
|15
|E0618
|LOCKNUT-CONDUIT-3/4"
|
|''(Not shown)''
|1
|}

==== ''<big>Current Relief Valve Configuration (December 2005 to Present)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Current Relief Valve Configuration.png|alt=BE-SL & BE-DS Current Relief Valve Configuration|frameless|543x543px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0260
|VALVE-MAIN SYSTEM RELIEF
|
|
|1
|-
|2
|HC0318
|GAUGE-PRESSURE
|
|''0-3000 LBS''
|1
|-
|3
|H1542
|ADAPTER-#12 JICM X #12 SAEM
|
|
|2
|-
|4
|H1650
|ADAPTER-#12 SAEM X #8 SAEF
|
|
|1
|-
|5
|H1606
|ADAPTER-90 DEG-#8 JICM X #8 SAEM
|
|
|1
|-
|6
|H0206
|PLUG-#4 NPT
|
|
|1
|-
|7
|43747003-2
|BRACKET-MOUNTING-RELIEF VALVE
|
|
|1
|-
|8
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|2
|-
|9
|HW0302
|BOLT-HHCS-1/4-20 X 3/4"
|
|
|2
|-
|10
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|6
|-
|11
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|}

==== ''<big>Discontinued Oil Cooler Configuration (Prior to December 2005)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Oil Cooler Configuration.png|alt=BE-SL & BE-DS Discontinued Oil Cooler Configuration|frameless|547x547px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|2
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|8
|-
|3
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|4
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|5
|E0611
|JUNCTION BOX-4" X 2" X 2"
|
|
|1
|-
|6
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
|7
|E0623
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .250" to .375"''
|1
|-
|8
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|2
|-
|9
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|3
|-
|10
|E0612
|COVER-JUNCTION BOX
|
|
|1
|}
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Oil Cooler Configuration 2.png|alt=BE-SL & BE-DS Discontinued Oil Cooler Configuration 2|frameless|550x550px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|4F363
|OIL COOLER
|
|''Includes mounting hardware''
|1
|-
|2
|41215017
|MOUNT-OIL COOLER
|
|
|1
|-
|3
|BI0107
|ELBOW-STR-90 DEG-#12 NPT
|
|
|4
|-
|4
|H1509
|ADAPTER-#10 JICM X #12 NPTM
|
|
|2
|-
|5
|4WT44
|FAN
|
|
|2
|-
|6
|4YD82
|GRILL-FAN
|
|
|2
|-
|7
|SS0112
|SCREW-SHCS-#8-32 X 5/8"
|
|
|16
|-
|8
|SS0303
|WASHER-FLAT-#8
|
|
|8
|-
|9
|SS0203
|NUT-NILN-#8-32
|
|
|16
|-
|10
|4YD79
|CORD-FAN
|
|''(Not shown)''
|2
|}

==== ''<big>Return Line Manifold</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Return Line Manifold.png|alt=BE-SL & BE-DS Return Line Manifold|frameless|555x555px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41247001
|MANIFOLD-RETURN LINE
|
|
|1
|-
|2
|HW0308
|BOLT-HHCS-1/4-20 X 2 1/2"
|
|
|2
|-
|3
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|6
|-
|4
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|5
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|6
|43017009-2
|BRACKET-MOUNTING-MANIFOLD
|
|
|1
|-
|7
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|2
|-
|8
|H1509
|ADAPTER-#10 JICM X #12 NPTM
|
|
|1
|-
|9
|H1501
|ADAPTER-#8 JICM X #6 NPTM
|
|
|2
|-
|10
|H1507
|ADAPTER-#8 JICM X #8 NPTM
|
|
|1
|-
|11
|H0208
|PLUG-#12 NPT
|
|
|1
|}

==== ''<big>Discontinued Pressure Reducing Valve Configuration (Prior to December 2005)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued High Performance Pressure Releasing Valve.png|alt=BE-SL & BE-DS Discontinued High Performance Pressure Releasing Valve|frameless|541x541px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0276
|VALVE-PRESSURE REDUCING
|
|
|1
|-
|2
|H1610
|ADAPTER-90 DEG-#10 JICM X #10 SAEM
|
|
|1
|-
|3
|H1545
|ADAPTER-#10 JICM X #10 SAEM
|
|
|1
|-
|4
|H1615
|ADAPTER-90 DEG-#6 JICM X #6 SAEM
|
|
|1
|-
|5
|HW0308
|BOLT-HHCS-1/4-20 X 2 1/2"
|
|
|2
|-
|6
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|7
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|8
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|}

==== ''<big>Current BE-DS-HP Lift Circuit Configuration (December 2005 to Present)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Current BE-DS-HP Circuit Configuration.png|alt= Current BE-DS-HP Circuit Configuration|frameless|549x549px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0215
|VALVE-CHECK-CARTRIDGE
|
|
|8
|-
|2
|H1560
|ADAPTER-45 DEG-#8 JICM X #8 SAEM
|
|
|4
|-
|3
|H1108
|ADAPTER-#12 JICM X #10 SAEM
|
|
|1
|-
|4
|H1647
|ADAPTER-90 DEG-#10 SAEM X #8 FNPT
|
|
|1
|-
|5
|H0007
|NIPPLE-# 8 NPT
|
|
|1
|-
|6
|HC0270
|VALVE-ADJUSTABLE FLOW CONTROL
|
|''Pressure compensated''
|1
|-
|7
|H1680
|ADAPTER-#10 JICM X #8 NPTM
|
|
|1
|-
|8
|H1690
|ADAPTER-#10 JICSW X #10 SAEM
|
|
|1
|-
|9
|H1612
|ADAPTER-90 DEG-#8 JICM X #10 SAEM
|
|
|1
|-
|10
|HC0283
|VALVE-COUNTER BALANCE
|
|
|1
|-
|11
|H1552
|ADAPTER-#6 JICM X #6 SAEM
|
|
|1
|-
|12
|H1504
|ADAPTER-#6 JICM X #4 NPTM
|
|
|1
|-
|13
|H1501
|ADAPTER-#8 JICM X #6 NPTM
|
|
|2
|-
|14
|43047002
|MANIFOLD-PILOT DOWN
|
|
|1
|-
|15
|H1579
|ADAPTER-90 DEG-#6 JICM X 4 NPTM
|
|
|2
|-
|16
|N/A
|HOSE-HYDRAULIC-1/4" X 24"
|
|''(Not shown)''
|1
|}

==== ''<big>Magnetic Starter Assembly</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) High Performance Magnetic Starter Assembly.png|alt=BE-SL & BE-DS High Performance Magnetic Starter Assembly|frameless|555x555px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0103-1
|MAGNETIC STARTER
|
|''NEMA 1''
|1
|-
|2
|E0608-1
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .450" to .560"''
|1
|-
|3
|E0623
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .250" to .375"''
|4
|-
|4
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|1
|-
|5
|E0622
|RESTRAINT-1/2"
|
|''Grip size .450" to .560"''
|1
|-
|6
|E0613
|RESTRAINT-3/4"
|
|''Grip size .500" to .625"''
|1
|-
|7
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|7
|-
|8
|E0618
|LOCKNUT-CONDUIT-3/4"
|
|
|1
|-
|9
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|3
|-
|10
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|7
|-
|11
|HW0103
|WASHER-LOCK-1/4"
|
|
|3
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|}

=== <big>Water Cart</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Water Cart 1.png|alt=BE-SL & BE-DS Water Cart 1|frameless|546x546px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|PB0033
|OVERFILL INDICATOR
|
|
|1
|-
|2
|PB0034
|LOCKNUT-CONDUIT-2"-NYLON
|
|
|1
|-
|3
|HC0308
|FILLER/BREATHER ASSEMBLY
|
|''Includes gaskets''
|1
|-
|4
|HW0209
|SCREW-RHMS-10-32 X 1/2"
|
|
|6
|-
|5
|550-057
|HOSE-FILL-3/4" X 15'
|
|
|1
|-
|6
|550-027
|ON/OFF VALVE
|
|''(Not shown)''
|1
|-
|7
|PB0902
|HOSE-3/4"
|
|
|30"
|-
|8
|HW1018
|HOSE CLAMP-3/4"
|
|
|1
|-
|9
|PB0603
|ADAPTER-3/4" NPT X 3/4" BARB
|
|
|1
|-
|10
|PB0456
|ELBOW-STR-90 DEG-3/4" NPT
|
|
|1
|-
|11
|PB0451
|ADAPTER-3/4" NPT X 3/4 GHT
|
|
|1
|-
|12
|PB0302
|PLUG-3/4" NPT
|
|
|
|-
|13
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|2
|-
|14
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|2
|-
|15
|SS0106
|SHCS-#10-24 X 1/2"-SST
|
|
|6
|-
|16
|SS0114
|BHSCS-#10-24 X 1/2" SST
|
|
|4
|-
|17
|SS0301
|WASHER-FLAT-#10-SAE-SST
|
|
|10
|-
|18
|00196701
|DECAL-BHS-12"
|
|
|1
|-
|19
|00196404
|LABEL-DANGER-"120 VOLTS"
|
|
|1
|-
|20
|00166648
|LABEL, NON-POTABLE
|
|
|1
|-
|21
|HW0418
|BOLT-HHCS-3/8-16 X 2-1/4"
|
| rowspan="3" |''Mounting Hardware''

''(Not shown)''
|2
|-
|22
|HW0031
|NUT-HEX-3/8-16 CENTERLOCK
|
|4
|-
|23
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|2
|}
[[File:IOP-400 BE-SL&DS (10-23) Water Cart 2.png|alt=BE-SL & BE-DS Water Cart 2|frameless|549x549px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|PB0150
|PUMP-SUBMERSIBLE
|
|''† See notes''
|1
|-
|2
|HW1018
|HOSE CLAMP-3/4"
|
|
|1
|-
|3
|46932005
|LEVEL SWITCH CONDUIT ASSEMBLY
|
|''Includes (2) Item #4 and Wiring''
|1
|-
|4
|E1381
|SWITCH-LIQUID LEVEL
|
|
|2
|-
|5
|SS0760
|HOSE CLAMP-4" TO 7"
|
|
|1
|-
|6
|HW1019
|HOSE CLAMP-1"
|
|
|2
|-
|7
|SS06010
|HANDLE
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Hose Barb Fitting modified at factory during assembly to remove threaded portion from Hose Barb end. Modification of Fitting required prior to installing Replacement Pump.''
|}
[[File:IOP-400 BE-SL&DS (10-23) Water Cart 3.png|alt=BE-SL & BE-DS Water Cart 3|frameless|553x553px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E1511
|SWITCH-ROCKER
|
|''Submersible rated''
|1
|-
|2
|E0378
|INDICATOR LIGHT-120VAC-GREEN
|
|''† See notes''
|1
|-
|3
|E0376
|INDICATOR LIGHT-120VAC-AMBER
|
|''† See notes''
|1
|-
|4
|E0377
|INDICATOR LIGHT-120VAC-RED
|
|''† See notes''
|1
|-
|5
|46917015
|PLACARD-INDICATOR LIGHT
|
|
|1
|-
|6
|E0505
|16-3 SO CORD
|
|
|72"
|-
|7
|E0653
|PLUG-120V/15A
|
|
|1
|-
|8
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|1
|-
|9
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|1
|-
|10
|PL0501
|GROMMET-1/2"
|
|
|2
|-
|11
|E1313
|SOCKET-RELAY-8 PIN
|
|
|1
|-
|12
|E0331
|RELAY-DPDT-110VAC
|
|
|1
|-
|13
|E0440
|TERMINAL BLOCK-8 POLE
|
|
|1
|-
|14
|E1070
|GROUND BAR-4 POSITION
|
|
|1
|-
|15
|HW0139
|SCREW-RHMS-#8-32 X 1 1/4"
|
|
|2
|-
|16
|HW0135
|SCREW-RHMS-#8-32 X 3/4"
|
|
|2
|-
|17
|HW1061
|SCREW-RHMS-#8-32 X 1"
|
|
|1
|-
|18
|HW0132
|NUT-NILN-#8-32
|
|
|5
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Water carts built prior to October 2021 used Multi-Piece Indicator Lights with replaceable bulb and lens are no longer available. Current Indicator Lights are 1-Piece LED Assembly. Replacement of any Multi-Piece Component requires replacing entire assembly with current, 1 -Piece Indicator Light.''
|}

=== <big>Level Assist (LAI)</big> ===

==== <big>''BE-SL Level Assist''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL Level Assist.png|alt=BE-SL Level Assist|frameless|564x564px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E1321A
|PHOTO EYE
|
|
|1
|-
|2
|HW0216
|SCREW-#10-24 X 2"
|
|''†'' ''See notes''
|2
|-
|3
|HW0032
|NUT-NILN-#10-24
|
|
|2
|-
|4
|43617046
|TARGET-PHOTO EYE
|
|
|1
|-
|5
|HW0302
|BOLT-HHCS-1/4-20 X 3/4"
|
|
|1
|-
|6
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|1
|-
|7
|HW0103
|WASHER-LOCK-1/4"
|
|
|1
|-
|8
|HW0002
|NUT-HEX-1/4-20
|
|
|1
|-
|9
|E0376
|INDICATOR LIGHT
|
|''††'' ''See notes''
|1
|-
|10
|HW0152
|WASHER-5/8" I.D.
|
|''†††'' ''For Item 9 (Not shown)''
|2
|-
|11
|E1321-RT
|REFLECTIVE TAPE
|
|''(Not shown)''
|A/R
|-
! colspan="6" |NOTES
|-
| colspan="6" |''Location of Indicator Light on the dash may vary from location shown.''
|-
| colspan="6" |''†'' ''Photo Eye & Reflector Mounting screws are trimmed to length.''
|-
| colspan="6" |''††'' ''Extractors built prior to October 2021 used Multi-Piece Indicator Lights with Replaceable Bulb and Lens are no longer available. Current Indicator Light is a 1-Piece LED Assembly. Replacement of any Multi-Piece Component requires replacing entire assembly with current, 1-Piece Indicator Light.''
|-
| colspan="6" |''†††'' ''Washers required for units that did not ship with Level Assist option from the factory.''
|}

==== <big>''BE-DS Level Assist''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-DS Level Assist.png|alt=BE-DS Level Assist|frameless|558x558px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E1321A
|PHOTO EYE
|
|
|1
|-
|2
|13537001-2
|MOUNT-PHOTO EYE
|
|
|1
|-
|3
|PL0502
|GROMMET
|
|
|1
|-
|4
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
|5
|E0376
|INDICATOR LIGHT-120VAC-AMBER
|
|''†'' ''See notes''
|1
|-
|6
|HW0152
|WASHER-5/8" I.D.
|
|''††'' ''For Item 5 (Not shown)''
|2
|-
|7
|E1321-RT
|REFLECTIVE TAPE
|
|''(Not shown)''
|A/R
|-
! colspan="6" |NOTES
|-
| colspan="6" |''Location of Indicator Light on the dash may vary from location shown.''
|-
| colspan="6" |''††'' ''Extractors built prior to October 2021 used Multi-Piece Indicator Lights with Replaceable Bulb and Lens are no longer available. Current Indicator Light is a 1-Piece LED Assembly. Replacement of any Multi-Piece Component requires replacing entire assembly with current, 1-Piece Indicator Light.''
|-
| colspan="6" |''†††'' ''Washers required for units that did not ship with Level Assist option from the factory.''
|}

==== <big>''Level Assist Junction Box Mounting''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-DS Level Assist Junction Box.png|alt= BE-DS Level Assist Junction Box|frameless|569x569px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0611
|JUNCTION BOX-4" X 2" X 2"
|
|
|1
|-
|2
|E0612
|COVER-JUNCTION BOX
|
|
|1
|-
|3
|E0623
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .250" to .375"''
|2
|-
|4
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|1
|-
|5
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|3
|-
|6
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|''Mounting Bolts (Not shown)''
|2
|}

=== <big>Blue Light (BE-BLU-LT)</big> ===

==== ''<big>BE-SL Blue Light</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL Blue Light.png|alt=BE-SL Blue Light|frameless|548x548px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43735004
|STANCHION-MOUNTING
|
|''Includes Junction Box''
|1
|-
|2
|EW2002B
|BLUE PROJECTION SPOTLIGHT
|
|
|2
|-
|3
|E0612
|COVER-JUNCTION BOX
|
|
|1
|-
|4
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|2
|-
|5
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|2
|-
|6
|HW0321
|BOLT-HHCS-5/16-18 X 1 1/4"
|
|
|2
|-
|7
|HW0106
|WASHER-FLAT-5/16"-SAE
|
|
|4
|-
|8
|HW0105
|WASHER-LOCK-5/16"
|
|
|2
|-
|9
|HW0004
|NUT-HEX-5/16-18
|
|
|2
|-
|REF
|43032006
|STANCHION ASSEMBLY
|
|''Includes Items 10 through 13''
|A/R
|-
|10
|43035003
|STACK LIGHT STANCHION
|
|
|1
|-
|11
|43037007-2
|CLAMP BRACKET
|
|
|1
|-
|12
|HW0305
|BOLT-HHCS-1/4-20 X 2"
|
|
|4
|-
|13
|HW0050
|NUT-FLANGED-1/4-20
|
|
|4
|-
|14
|E1010
|RECEPTACLE-TWIST LOCK
|
|''(Not shown)''
|2
|-
|15
|E1011
|PLUG-TWIST LOCK
|
|''(Not shown)''
|2
|}

==== ''<big>BE-DS Blue Light</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-DS Blue Light.png|alt=BE-DS Blue Light|frameless|500x500px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43735004
|STANCHION-MOUNTING
|
|''Includes Junction Box''
|2
|-
|2
|EW2002B
|BLUE PROJECTION SPOTLIGHT
|
|
|2
|-
|3
|E0612
|COVER-JUNCTION BOX
|
|
|2
|-
|4
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|4
|-
|5
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|4
|-
|6
|HW0321
|BOLT-HHCS-5/16-18 X 1 1/4"
|
|
|4
|-
|7
|HW0106
|WASHER-FLAT-5/16"-SAE
|
|
|8
|-
|8
|HW0105
|WASHER-LOCK-5/16"
|
|
|4
|-
|9
|HW0004
|NUT-HEX-5/16-18
|
|
|4
|-
|10
|E1010
|RECEPTACLE-TWIST LOCK
|
|''(Not shown)''
|2
|-
|11
|E1011
|PLUG-TWIST LOCK
|
|''(Not shown)''
|2
|}

==== ''<big>Blue Light Power Supply for Units Without IIoT (Prior to February 2020)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Blue Light Power Supply.png|alt=BE-SL & BE-DS Blue Light Power Supply|frameless|584x584px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|N/A
|ENCLOSURE-8" X 8" X 4"
|
|''Consult factory''
|1
|-
|2
|E0135
|PANEL-COMPONENT MOUNTING
|
|''Blank panel without holes''
|1
|-
|3
|PS5R-SC12
|POWER SUPPLY
|
|
|1
|-
|4
|E0908
|MOUNTING RAIL
|
|''Sold by length''
|A/R
|-
|5
|YE0402
|TERMINAL BLOCK
|
|
|4
|-
|6
|YE0405
|END BARRIER
|
|
|1
|-
|7
|YE0406
|END ANCHOR
|
|
|2
|-
|8
|E0341
|GROUND LUG
|
|
|1
|-
|9
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|3
|-
|10
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|3
|-
|11
|HW0130
|SCREW-RHMS-#8-32 X 1/2"
|
|''2 per Mounting Rail''
|5
|-
|12
|HW0132
|NUT-NILN-#8-32
|
|''2 per Mounting Rail''
|5
|-
|13
|HW0133
|WASHER-FLAT-#8-SAE
|
|''2 per Mounting Rail''
|5
|-
|14
|00196404
|LABEL-DANGER-"120 VOLTS"
|
|
|1
|}

= <big>Service & Maintenance</big> =

== <big>Daily Inspection List</big> ==
The points listed below should be visually inspected daily prior to initial start up of the Battery Extractor to ensure safe and proper operation of the unit and to help avoid unnecessary down time.

# Walk around unit and inspect for any physical damage to machine not previously noted.
# Verify all guards are in place.
# Inspect the AC power feed for any damage.
# Vacuum equipped units: Inspect vacuum cups for damage to cup sealing surface, backup casting, and vacuum hoses. Magnet equipped units: Inspect magnets for damage to attachment face, proximity sensor cover, cables and connections.
# Inspect travel path and area around unit for any hydraulic oil that could be a potential repair/maintenance issue and/or safety hazard.
# Check oil level in hydraulic reservoir at fill level gauge.
# Check that operator safety gate and all safety switches are in proper working order.
# Verify extractor path is free of obstructions.
# Check roller beds for any debris and clean as required.
# Board unit, engage system and verify all functions are operating properly and that no abnormal or unusual noises are present.

<nowiki>*</nowiki>USE FORM IF-5008 WHEN PREFORMING DAILY INSPECTIONS.

== <big>Operator's Daily Checklist</big> ==
[[File:IOP-400 BE-SL&DS (10-23) Operator's Daily Checklist.png|alt=BE-SL & BE-DS Operator's Daily Checklist|frameless|1230x1230px]]

== <big>Recommended Battery Extractor Lubrication Intervals</big> ==
{| class="wikitable"
!Lubrication Task
!'''# of Places'''
!Intervals
|-
|'''1. Lubricate grease fittings using #2 lithium based grease'''
|
|
|-
|A. Extractor arm drive nut and carrier bearings
|5 places
|50 hrs / Weekly
|-
|B. Idler casters
|2 places
|200 hrs / Weekly
|-
|'''2. Wipe off and lubricate chains using light machine oil'''
|
|
|-
|A. #80 Lift chains (Not applicable to BE-SL units)
|4 places
|200 hrs / Monthly
|-
|B. #60 Equalization chains
|4 places
|200 hrs / Monthly
|-
|C. #35 Powered roller chains
|8 places
|200 hrs / Monthly
|-
|'''3. Change return line hydraulic fluid filter'''
''(Oil filtration of at least 20 microns is recommended)''
|1 place
|300 hrs / Twice Quarterly
|-
|'''4. Change hydraulic fluid'''
| -
|600 hrs / Quarterly *
|-
|'''5. Complete preventative maintenance (PM)'''
Use form IF-5029 for Vacuum equipped units.

Use form IF-5028 for Magnet equipped units.
| -
|600 hrs / Quarterly
|-
! colspan="3" |NOTES
|-
| colspan="3" |''These recommendations are based on average use in a typical warehouse environment and may be adjusted based on specific circumstances. Dusty and/or extreme hot/cold environments may require more frequent lubrication.''
|-
| colspan="3" |''* BHS recommends implementing an oil sampling and analysis program to monitor hydraulic fluid condition and determine when hydraulic fluid changes are required. The fluid analysis program should be a continuous process and all results should be evaluated. Changes in the condition of the hydraulic system may indicate component wear, fluid deterioration and/or contamination.''
|}
{|
|[[File:NOTICE-warn.png|alt=NOTICE|frameless|120x120px]]
|
* '''The mounted bearings used on the power rollers, equalization shafts, drive wheels, and drive screw are sealed and shielded bearings. Lubrication may breach the seals of these bearings, therefore these bearings should not be lubricated unless the machine has been cleaned with a high pressure wash on a regular basis (not recommended).'''
* '''Hydraulic fluid should not exceed 140°F (60°C) for extended periods.'''
|}

=== <big>'''Reservoir Capacities ''(APPROX.)'''''</big> ===
{|
|BE-SL
|18 gal (68 L)
|-
|BE-DS
|18 gal (68 L)
|-
| rowspan="2" |BE-TS
|30 gal (114 L) ''(Units built Pre-2014)''
|-
|45 gal (170 L) ''(Units built 2014 to Present)''
|-
|BE-QS
|60 gal (227 L)
|}
The reservoir should be filled so fluid level is within a half inch (1/2") of the top of sight glass. Use Chevron AW 68 or equivalent ISO 68 grade hydraulic oil with anti-wear additives and foam suppressant.

'''''NOTE'':''' Some units shipped from the factory with AW 32 oil for cold environment operation. Units using AW 32 from the factory may experience poor performance if AW 68 is used instead of AW 32 due to the increased viscosity of the oil.

== <big>Preventative Maintenance Reports</big> ==

=== <big>Vacuum Extraction</big> ===
[[File:Battery Extractor Series - Vacuum Extraction Planned Maintenance Inspection Report Page 1.png|alt=Battery Extractor Series - Vacuum Extraction Planned Maintenance Inspection Report Page1|frameless|1238x1238px]]

[[File:Battery Extractor Series - Vacuum Extraction Planned Maintenance Inspection Report page2.png|alt=Battery Extractor Series - Vacuum Extraction Planned Maintenance Inspection Report Page 2|frameless|1230x1230px]]

=== <big>Magnet Extraction</big> ===
[[File:Battery Extractor Series - Magnet Extraction Planned Maintenance Inspection Report Page 1.png|alt= Battery Extractor Series - Magnet Extraction Planned Maintenance Inspection Report Page 1|frameless|1224x1224px]]

[[File:Battery Extractor Series - Magnet Extraction Planned Maintenance Inspection Report Page 2.png|alt= Battery Extractor Series - Magnet Extraction Planned Maintenance Inspection Report Page 2|frameless|1233x1233px]]

== <big>80292002-i – Equalization Chain Installation / Resetting Procedure</big> ==

=== <big>Required Tools</big> ===

* Large standard screwdriver
* 1/8", 5/32", 3/16" Allen wrench
* (2) 1-1/8" Open-end wrenches
* Needle nose pliers
* 6" Steel scale (ruler)
* Brake cleaner (non-chlorinated)
* Loctite #242 (blue)
* 80292002 - E.Q. Adjustment stop kit (SL, DS, TS) or 80492001 - BE-QS E.Q. Adjustment stop kit
* Ladder or work platform ''(see notes)''

=== <big>''Optional Tools''</big> ===

* Wire brush for removing Loctite from components prior to reassembly

=== <big>Notes</big> ===

* ''A ladder, man lift or other device is required to access the upper E.Q. studs on BE-TS and BE-QS units.''
* ''The following procedures must be performed with the extractor unloaded and in a level area of the travel path.''
* ''Installation of the E.Q. stop kit requires (4) persons plus a trained battery extractor operator to raise and lower the inner carriage.''
* ''It is recommended to have new E.Q. chain connecting links on hand prior to performing the following procedures.''
* ''The upper E.Q. stud lock washers cannot be reused and must be replaced prior to reassembly.''

[[File:IOP-400 BE-SL&DS (10-23) Page 369 Image 0001.png|alt=BE-TS with EQ Adjustment Stops Installed|none|thumb|300x300px|BE-TS with EQ Adjustment Stops Installed]]

=== <big>IMPORTANT</big> ===

* '''Read and understand the Safety and De-energization Procedure TP-606 before starting this procedure.'''
* '''Read and understand these instructions completely before starting this procedure.'''

=== <big>Procedure</big> ===
1. Remove the inner and outer frame guards to access the lower equalization studs.

2. Raise the inner frame approximately 30" (762 mm) for SL, DS and TS units or 50" (1270 mm) for QS units from the fully lowered position. Install (1) adjustment stop at each corner of the roller bed. See Figure 1.
[[File:IOP-400 BE-SL&DS (10-23) EQ Chain Instructions-Figure1.png|alt=|none|thumb|375x375px|FIGURE 1]]
3. Slowly lower the inner carriage until the roller bed is firmly and securely seated against all four stops. See Figure 2.
[[File:IOP-400 BE-SL&DS (10-23) Page 370 Image 0002.png|alt=Roller bed firmly seated against all four stops|none|thumb|398x398px|FIGURE 2]]
4. Lockout/tagout the B.E. per your corporate policy.

5. De-energize the B.E. per BHS Safety and De-energization procedure TP-606.

6. Loosen and remove the upper hex nuts and remove the upper chain studs. Remove the lock washers from the upper chain studs. Save the hex nuts for reassembly later. Discard the lock washers and obtain new, 3/4" split-ring lock washers for reassembly.

7. If replacing the chain, remove the upper stud and remove the chain from the lower stud. Discard the connecting links.

* ''If the E.Q. chains are being reset due to a connecting link failure, it is recommended to also replace the stud where the connecting link failed.''
* ''It is recommended to replace the connecting links when replacing or resetting the E.Q. chains.''

8. If replacing a lower stud, remove the connecting link and disconnect the chain. Loosen the hex nut and remove the stud. Remove the hex nut from the old stud and reinstall it on the new stud. Reinstall the new stud so that it is flush with the bottom of the frame and the hole is aligned front-to-back with the extractor.

9. Attach the chains to the lower studs using the connecting links. Attach the upper studs to the chains using the connecting links, making sure the nut is threaded down near the connecting link and lay the chains in the frame. See Figure 3.

* ''Do not fully assemble the lower connecting links by bending the cotter pins as the connecting link may need to be removed later for stud adjustment.''[[File:IOP-400 BE-SL&DS (10-23) EQ Chain Attached to Upper Stud.png|alt=BE-SL & BE-DS EQ Chain Attached to Upper Stud|none|thumb|300x300px|FIGURE 3]]

10. If new E.Q. sprockets are to be installed, remove the clamp collars and old sprockets. Install the new sprockets and reinstall the clamp collars. DO NOT tighten the set screws at this point as adjustment/alignment may be required.

* ''Sprockets MUST be keyed in-line.''

11. Align the E.Q. shafts so that the keyways are in the 2 o'clock position (approximately 60 degrees from vertical). This will bring the sprocket set screws to the top of the sprocket when the inner carriage is lowered. See Figure 4.
[[File:IOP-400 BE-SL&DS (10-23) EQ Shafts aligned 60 Degrees from Vertical.png|alt=BE-SL & BE-DS EQ Shafts aligned 60 Degrees from Vertical|none|thumb|300x300px|FIGURE 4]]
12. Starting with the inside chain, route the chain over the sprocket directly above the lower stud and under the inside sprocket on the opposite shaft. Attach the upper stud to the top cross bar, making sure a new 3/4" split -ring lock washer is installed between the cross bar and lower hex nut. Hand tighten the upper stud adjusting nut to remove slack from the chain. See Figure 5.

13. Route the outer chain over the sprocket, above the stud and under the sprocket on the opposite shaft. Attach the upper stud to the top cross bar, making sure a new, 3/4" split-ring lock washer is installed between the cross bar and lower hex nut. Hand tighten the upper stud adjusting nut to remove slack from the chain. See Figure 5.

* ''It is recommended to begin at the operator end where room is limited allowing easier access at the opposite end to route the chain under the final sprocket.''

[[File:IOP-400 BE-SL&DS (10-23) Inside and Outside EQ Chains.png|alt=BE-SL&DS Inside and Outside EQ Chains|none|thumb|499x499px|FIGURE 5]]
14. Repeat steps 11 through 13 for the opposite side of the extractor. It is likely that a large, standard screwdriver will be necessary to position the final chain over the sprocket. See Figure 6.
[[File:IOP-400 BE-SL&DS (10-23) Page 371 Image 0002.png|alt=It is likely that a large, standard screwdriver will be necessary to position the final chain over the sprocket.|none|thumb|300x300px|FIGURE 6]]
15. Adjust the lower studs up or down as necessary to take the slack out of the chain between the lower studs and the sprockets by removing the connecting link from the stud and turning the stud. Tighten the hex nuts against the frame once the studs have been adjusted. Reattach the chain.

* DO NOT allow the stud to twist when tightening the hex nuts.

16. Tighten the upper hex nut on the upper studs until there is approximately 1/4" (7 mm) of total deflection in the middle of the upper, vertical chain sections. Tighten the lower hex nuts on the upper studs to lock the studs in place.

* ''Each section of chain between the sprockets should have approximately the same tension as the other on the same side. See Figure 5.''

17. Raise the inner frame and remove the adjustment stops from the four corners and lower the inside frame.

18. Verify equalization sprocket and stud alignment by using a 6" scale. Measure the distance from the inside roller bed frame to the center of the equalization stud. Compare this distance with the measurements from the inside roller bed frame to the center-lines of the sprockets. Adjust the position of the sprocket as necessary to make the distances equal. This will ensure the chain and sprockets are in line with the stud. Repeat this process for the three remaining chains. See Figures 7 & 8.

19. Raise and lower the inner frame several times and listen for any chain popping noises to confirm the sprockets are in line with the lower studs. If there is no popping noise, lower the inner frame all the way down.
[[File:IOP-400 BE-SL&DS (10-23) EQ Chain Verify equalization sprocket and stud alignment by using a 6in scale-Fig7.png|alt=BE-SL&DS EQ Chain Procedure FIgure 7 - Verify equalization sprocket and stud alignment by using a 6" scale|none|thumb|300x300px|FIGURE 7]]
[[File:IOP-400 BE-SL&DS (10-23) EQ Chain Verify equalization sprocket and stud alignment by using a 6in scale-Fig8.png|alt=BE-SL & BE-DS EQ Chain Verify equalization sprocket and stud alignment by using a 6in scale - Fig 8|none|thumb|300x300px|FIGURE 8]]
20. Clean any existing, hardened Loctite from the sprockets, sprocket sets screws, clamp collars and clamp collar bolts.

21. Apply Loctite to and tighten the set screws on the sprockets. Slide the clamp collars against the outside sprocket, loctite and tighten the clamp collars.

== <big>80292001-i – Battery Extractor Service Stand Installation Instructions</big> ==

=== <big>Required Tools</big> ===
None

=== <big>Notes</big> ===

* ''Refer to kit part # 80292001 or 80392001 for the complete bill of materials supplied.''
* ''Remove ALL batteries from extractor prior to installation / service.''
* ''Installation of service stands requires (2) persons plus a trained battery extractor operator to raise and lower the inner carriage. DO NOT attempt installation with less than (3) persons.''

[[File:IOP-400 BE-SL&DS (10-23) Single Level Service Stand Properly Installed.png|alt= Single Level Service Stand Properly Installed|none|thumb|368x368px|Single Level Service Stand Properly Installed]]

=== <big>IMPORTANT</big> ===

* '''Read and understand the Safety and De-energization Procedure TP-606 before starting this procedure.'''
* '''Read and understand these instructions completely before starting this procedure.'''

=== <big>Procedure</big> ===
1. Have a qualified operator raise the inner carriage of the extractor to the required height for installation. For single level applications, the required height will be approximately 25" (64 cm) from the fully lowered position. For double, triple, and quad stack machines, the required height will be approximately 55" (140 cm) from the fully lowered position.

* On double, triple, and quad stack battery extractors, the operator either must remain on the operator platform during service or be provided an OSHA approved method of egress. This is not applicable to single level battery extractors as the operator platform height is fixed.

2. Install the stands by engaging the top of the stand into the inner carriage cutouts. Place the bottom channel of the stand over the tube of the outer frame. The top flanges of each stand are tapered to aid in proper alignment of the stand with the inner frame.

See Figures 1 & 2.
[[File:IOP-400 BE-SL&DS (10-23) engaging the top of the stand into the inner carriage cutout.png|alt=Properly seated in cutout|none|thumb|300x300px|FIGURE 1]]
[[File:IOP-400 BE-SL&DS (10-23) Page 374 Image 0005.png|none|thumb|300x300px|FIGURE 2]]
3. Once BOTH stands have been properly placed, SLOWLY lower the inner carriage while the stands are held in place.

4. Once the inner carriage is firmly seated on the service stands, verify the stands are securely installed. See Figure 3.
[[File:IOP-400 BE-SL&DS (10-23) Page 374 Image 0006.png|none|thumb|450x450px|FIGURE 3]]

== <big>Trouble Shooting Guide</big> ==
{| class="wikitable"
!Problem Symptom
!Probable Cause
!Solution
|-
|Hydraulic power Unit does not operate.
No electric to power unit motor.
|1. No AC power to Unit.
2. Reset on magnetic motor starter tripped.

3. Gate switch not actuated.

4. Foot Pedal switch not engaged.

5. Emergency Stop switch is depressed.
|1. Check fuses or breaker.
2. Check reset button.

3. Make sure safety gate is engaging switch.

4. Check foot pedal for obstruction.

5. Reset button using machine key.
|-
|Power unit runs but no pressure reading at gauge,
also no functions move.
|1. AC input is in reverse phase. Motor is running backwards.
2. Main system relief valve stuck open or defective.

3. Coupling between motor and pump loose.
|1. Reverse any two of the three hot lines to unit.
2. Check relief valve cartridge for trash or debris.

Replace as required.

3. Inspect coupling assy.
|-
|Magnetic starter contact chatters-at startup.
Contact chatters while traveling.
|1. 1 leg of 3 phase input power out.
2. Safety gate and/or gate switch out of adjustment.
|1. Check fuse or circuit breaker at service panel.
2. Check and adjust gate or switch as required to

ensure full engagement of plunger on gate

switch and that the safety gate is not bouncing

due to vibration.
|-
|No floor travel empty or loaded-all other functions work properly.
|1. Extractor arm off center-left to right.
2. Proximity switch or sensing bracket out of target range.

3. Proximity switch defective or broken.

4. Bad solenoid coil on floor cutout valve.

5. Spool on floor cutout valve stuck open.
|1. Center arm.
2. Adjust as needed to achieve 1/4” clearance.

3. Check switch and replace.

4. Check solenoid and replace if needed.

5. Remove and clean spool cartridge or replace.
|-
|Floor travel moves but is sluggish
and stalls with a load at certain points.
|1. Uneven floor conditions. High/low spots.
2. Excessive tire wear.

3. Wheel shaft-to-motor shaft coupling on drive wheel assembly loose or broken.

4. Debris lodged under battery extractor.
|1. Check flatness of floor. Check guidance track for scraping of guide arm on top of angle.
2. Measure under clearance of battery extractor. Should be no less than 5/8” replace poly wheels as needed.

3. Inspect drive assembly while under load to see if shafts and couplings are moving in unison. Repair as needed.

4. Inspect under unit and remove debris.
|-
|Inner carriage bounces while lifting under load,
but not when empty.
|1. Down speed adjustment valve open too far.
|1. Adjust as needed to eliminate carriage bounce.
|-
|Inner carriage does not lift evenly.
Four corners do not land evenly against outer frame tube.
|1. Equalization chains are out of adjustment.
2. Excessive chain or sprocket wear.

3. Equalization chains are out of synchronization. Possibly may have jumped a sprocket tooth.

4. Broken bearing housing on mounted shaft.

5. Lift cylinder roping chains out of adjustment.
|1. Readjust with the top stud until equal tension is achieved.
2. Replace as needed.

3. Evaluate and resynchronize as required.

4. Inspect and replace.

5. Readjust as needed to equal tension on all four cylinders in full down position.
|}

= <big>Aftermarket Support</big> =
[https://na.bhs1.com/blog/post/tt-922-technical-support Click here] for details on BHS' Aftermarket Support.

= <big>Statement of Warranty</big> =
[https://store.bhs1.com/warranty Click here] for details on BHS' Statement of Warranty.

(BE-SL & -DS) Single Level & Double Stack Operator Aboard Battery Extractors – Parts & Service Manual (IOP-400)

2026-01-09T15:28:14Z

Mbowen: /* [Current] Helical Actuator (July 2023 to Present) */

'''Looking for a specific replacement part?''' Ctrl-F (or Command-F for Mac users) brings up your browsers search panel and can search any text on the entire web page. Find parts by searching a part # or part description.

'''Register your equipment with [https://na.bhs1.com/media-library/bhs-optima/ BHS Optima], BHS's free app.'''

'''California Residents''': WARNING: This product contains chemicals known to the State of California to cause cancer and/or reproductive harm, and birth defects or other reproductive harm. [https://na.bhs1.com/about-bhs/compliance-statement-for-california-proposition-65/ Learn more here.]

= <big>Preface</big> =
This manual is to be used to service '''SINGLE LEVEL (BE-SL)''' as well as '''DOUBLE STACK (BE-DS)''' Battery Extractors.

Any views not specifically stated otherwise are of the Single Level Extractor. The parts listed are common for Single Level (BE-SL) and Double Stack (BE-DS) unless otherwise noted in the notes column of the Parts Lists. ''See Example Below''.
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="2" |1
|00158001-10
|CHAIN-ROLLER-#60
|
|''BE-SL Only''
|4
|-
|00158001-12
|CHAIN-ROLLER-#60
|
|''BE-DS Only''
|4
|}
For Items or Assemblies that are unique to only the SL or DS, it will be designated as such on the diagram and have a separate, corresponding parts list for that diagram.

When servicing '''HIGH PERFORMANCE (BE-DS-HP)''' models, refer to the [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#High_Performance_Options High Performance Option] section for all parts unique to High Performance Units. If a particular part is not found in the [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#High_Performance_Options High Performance Option] section, refer tot the Standard Parts Section(s) of this manual.

= <big>TP-606 – Safety & De-Energization Procedures</big> =

== <big>General Safety</big> ==
{|
| [[File:Read Before Operating Notice.png|alt=Read Before Operating|frameless|120x120px|link=https://tech.bhs1.com/index.php/File:Read_Before_Operating_Notice.png]]
|
*Read and understand all instructions and warnings before using or servicing this equipment.
*Keep these instructions for future reference.
|}

* Battery Extractor (BE) units shall only be operated by suitable persons of at least 18 years of age, who have been trained in the proper and safe operation of the BE and expressly certified/charged, in writing, by the user or their representative.
* Only one person is permitted to travel on the BE at any time.
* BE units shall only be used indoors in an industrial setting on a hard, nonslip, and level floor without defects including but not limited to holes, gouges, cracks, drains or obstacles comprised of concrete or other suitable industrial material meeting the minimum requirements specified by BHS as well as any local requirements.
* A licensed structural engineer should be consulted prior to installing a BE on any building level other than the ground floor.
* BE units are not designed to be shipped or transported after initial delivery.
* Failure to follow these instructions and warnings may result in property damage, personal injury or death.

=== <big>Work Area</big> ===

* Keep work area clean and well lit. Cluttered work areas and poor lighting can lead to accidents.
* Clean up/contain any fluid spills immediately to prevent slips or falls.
* Be aware of potential hazards when performing any service or maintenance to the unit.

===<big>Service & Maintenance</big>===
Service personnel shall wear Personal Protective Equipment (PPE) appropriate for the task being performed.
{|
|[[File:Electrical Hazard Warning.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Electrical_Hazard_Warning.png]]
[[File:Danger Warning.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Danger_Warning.png|alt=DANGER]]
|
===<big>Lockout/Tagout</big>===
'''Lockout/tagout the BE per your corporate policy, if damaged or not functioning properly. Lockout/tagout and de-energize all systems prior to performing any maintenance or service to unit.'''
|}
{|
|[[File:Warning-Battery-Explosion.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Warning-Battery-Explosion.png]]
[[File:Danger Warning.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Danger_Warning.png|alt=DANGER]]
|
===<big>Lead-Acid Battery Explosion Hazard</big>===
'''DO NOT allow open flames or sparks of any kind near a battery. Highly explosive gas is generated when charging a battery that can remain in battery cells for extended periods of time after charging is complete.'''
*Always wear appropriate PPE including rubber apron, gloves, boots and full face shield when performing service or maintenance to any lead-acid batteries.
*DO NOT place metal or other conductive objects on top of battery. Arcing may occur causing damage to the battery and/or serious personal injury or death.
*Use only chargers matching the voltage and amperage of the battery being charged. Overcharging a battery can cause damage to the battery, charger and/or serious personal injury or death.
*Turn off charger before disconnecting battery from charger. Arcing between battery and charger connectors can cause damage to the connectors and/or serious personal injury or death.
|}
{|
|[[File:Warning-Hydrualic-Hazard.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Warning-Hydrualic-Hazard.png]]
[[File:Warning.png|alt=WARNING|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Warning.png]]
|
===<big>Hydraulic Hazards</big>===
'''AVOID HIGH PRESSURE FLUIDS-Escaping fluid under pressure can penetrate the skin causing serious injury. Relieve pressure before disconnecting hydraulic lines. Tighten all connections before applying pressure. Keep hands and body away from pin holes which eject fluids under high pressure. Use a piece of cardboard or paper to search for leaks. DO NOT use your hand.'''

'''Any fluid injected into the skin under high pressure should be considered a serious medical emergency despite an initial normal appearance of the skin. There will be a delayed onset of pain, and serious tissue damage may occur. Medical attention should be sought immediately.'''
|}
{|
![[File:No Pacemakers Notice.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:No_Pacemakers_Notice.png]][[File:Strong Magnet Field Hazard Warning.png|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Strong_Magnet_Field_Hazard_Warning.png]]
[[File:Warning.png|alt=WARNING|frameless|100x100px|link=https://tech.bhs1.com/index.php/File:Warning.png]]
|
===<big>Electromagnet Hazard</big>===
'''Units equipped with magnetic extraction generate strong magnetic fields. Persons with pacemakers SHOULD''' '''NOT''' '''operate or be in close proximity to equipment during operation.'''

'''Failure to comply with this direction''' '''could result in serious personal injury or death.'''
|}

=== <big>Operational Safety</big> ===

* Only personnel trained in the proper and safe operation of BE units may operate or service the BE.
* Operators shall wear appropriate PPE suitable for working with industrial lead-acid batteries while operating the BE ''(See [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Lead-Acid_Battery_Explosion_Hazard Lead-Acid Battery Explosion Hazard] section).''
* All data plates, warning labels, placards, etc. shall be in place and legible at all times. Contact BHS for re-placement data plates, warning labels, placards or instructions.
* All users and service personnel shall be familiar with the meaning and risks associated with all data plates, warning labels, etc.
* All operators and service personnel shall be aware of potential crush and shear points while operating or servicing the BE.
* Keep hands and arms inside the operator compartment while operating the BE.
* Remove BE from service if damaged, defective, or operating improperly (or becomes such while operating) until repairs can be made to correct any problem(s).
* All operators shall be aware of the location of the end stops in the travel path to prevent driving the BE into the end stops.

=== <big>Do's and Don'ts</big> ===

* '''DO NOT''' exceed the maximum capacity of the BE.
* '''DO NOT''' modify or fit the BE with attachments without prior, written approval from BHS.
* '''DO NOT''' perform any maintenance or service to the BE with a battery loaded on the BE.
* '''DO NOT''' allow anyone to ride in or on the BE.
* '''DO NOT''' operate the BE with any guard or cover removed unless required for maintenance or repair.
* Disconnect the BE from all power sources before attempting to perform service or maintenance to the unit.
* '''DO NOT''' drive the BE into the end stops.
* '''DO NOT''' operate the BE if disengaged from the guidance track.
* '''DO NOT''' allow a battery to exit the BE when a lift truck or battery stand is not present to accept the battery.
* '''DO NOT''' rotate the arm onto a battery such that any part of the extractor arm, vacuum cup or magnet contacts the top of the battery.
* '''DO NOT''' allow anyone to enter the area under the carriage without the service stands properly installed.
* '''DO NOT''' use the BE in a manner for which it is not intended. Some examples of prohibited use are but not limited to:
** To transport people
** As a vehicle jack
** To lift loads greater than its rated load capacity
** Where unintentional movement may exist
** Having direct contact with foodstuffs
** In a potentially explosive atmosphere

== <big>De-Energization</big> ==
1. Fully lower the BE roller bed or position the roller bed on service stands if service requires the bed be raised. See Figures 1 & 2.
{|
|[[File:WARNING-warn.png|alt=WARNING|frameless|100x100px]]
!Failure to properly support the roller bed when performing service under the BE could result in injury from the roller bed lowering unexpectedly.
|}
[[File:IOP-400 BE-SL&DS (10-23) Fully Lower BE Roller Bed.png|alt=Fully lowered BE roller bed|none|thumb|FIGURE 1]]
[[File:IOP-400 BE-SL&DS (10-23) BE Roller Bed on Service Stands .png|alt=Raised BE roller bed positioned on service stands|none|thumb|FIGURE 2]]
2. Turn key on dashboard to the “OFF” position. See Figure 3.
[[File:IOP-400 BE-SL&DS (10-23) De-Energization Figure 3.png|alt=Key on BE-SL & BE-DS dashboard turned to the “OFF” position.|none|thumb|FIGURE 3]]
3. Disconnect power to the extractor or shut off the electrical branch circuit breaker.
{|
|[[File:Danger Warning.png|alt=DANGER|frameless|100x100px]]
|'''Failure to disconnect electrical power to the BE could result in electrical shock. Serious personal injury or death will occur.'''
|}
4. Actuate all hydraulic levers in both directions to re-lease any stored hydraulic pressure. See Figure 4.
{|
|[[File:WARNING-warn.png|alt=WARNING|frameless|100x100px]]
|'''Failure to release any stored hydraulic pres-sure could result in injury from:'''
* '''Escaping hydraulic fluid under high pressure (see ''[https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Operational_Safety HYDRAULIC HAZARDS]'' in the ''[https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#General_Safety GENERAL SAFETY]'' section).'''
* '''Unexpected movement of hydraulic components.'''
|}
[[File:IOP-400 BE-SL&DS (10-23) Actuate all Hydraulic Levers in Both Directions.png|alt=Actuate all hydraulic levers in both directions to release any stored hydraulic pressure.|none|thumb|FIGURE 4]]

== <big>Labels & Placards</big> ==
'''Operators should be familiar with the meaning of the following labels and placards found on the BE to ensure proper and safe operation.'''
{| class="wikitable"
|-
![[File:Read Before Operating Notice.png|alt=Read Before Operating|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:Read_Before_Operating_Notice.png]]
|'''Read and understand instruction manual prior to use.'''
|-
![[File:Lockout-Before-Servicing-Notice.png|alt=Lockout Before Servicing Unit|frameless|150x150px]]
|'''Lockout before servicing.'''
|-
![[File:IOP-400 BE-SL&DS (10-23) Extractor Arm Positioning Arrows.png|alt=BE-SL & BE-DS Extractor Arm Positioning Arrows|frameless|150x150px]]
|'''Extractor arm positioning arrows'''
|-
![[File:Do Not Operate Without Guards or Covers Notice.png|alt=DO NOT Operate Without Guards or Covers Notice|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:Do_Not_Operate_Without_Guards_or_Covers_Notice.png]]
|'''DO NOT operate with guards or covers removed'''
|-
![[File:IOP-400 BE-SL&DS (10-23) No Riders Allowed.png|alt= No riders allowed|frameless|150x150px]]
|'''NO riders allowed.'''
|-
![[File:No Pacemakers Notice.png|alt=DO NOT operate by or in close proximity to people with pacemakers.|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:No_Pacemakers_Notice.png]]
|'''DO NOT operate by or in close proximity to people with pacemakers.'''
|-
![[File:Strong Magnet Field Hazard Warning.png|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:Strong_Magnet_Field_Hazard_Warning.png]]
[[File:Warning.png|alt=WARNING|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:Warning.png]]
|'''Strong Magnet Field Hazard'''
* Attraction between magnet and metallic objects can crush.
* Keep unsecured metallic objects away from magnet.
* De-energize and lockout/tagout before servicing.
|-
![[File:Chain Entanglement Hazard Warning.png|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:Chain_Entanglement_Hazard_Warning.png]]
[[File:Warning.png|alt=WARNING|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:Warning.png]]
|'''Chain Entanglement Hazard'''
* Moving chains and sprockets can crush and cut.
* Keep hands and fingers clear. Do not operate with guards removed.
* De-energize and lockout/tagout before servicing.
|-
![[File:Electrical Hazard Warning.png|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:Electrical_Hazard_Warning.png]]
[[File:Danger Warning.png|alt=DANGER|frameless|150x150px|link=https://tech.bhs1.com/index.php/File:Danger_Warning.png]]
|'''Electrical Hazard'''
* Energized components can cause electrical shock.
* De-energize and lockout/tagout before servicing.
|-
![[File:BE-SL and BE-DS Power Off-On.png|alt=BE-SL and BE-DS Power Off-On|frameless|180x180px]]
|'''Power Off/On'''
|-
![[File:IOP-400 BE-SL&DS (10-23) Horn Control.png|alt=BE-SL and BE-DS Horn Control |frameless|180x180px]]
|'''Horn (If equipped)'''
|-
![[File:IOP-400 BE-SL&DS (10-23) Vacuum Control.png|alt=BE-SL and BE-DS Vacuum Control |frameless|180x180px]]
|'''Vacuum Off/On (If equipped)'''
|-
![[File:IOP-400 BE-SL&DS (10-23) Magnet Extraction.png|alt=BE-SL and BE-DS Magnet Off/On|frameless|180x180px]]
|'''Magnet Off/On (If equipped)'''
|-
![[File:IOP-400 BE-SL&DS (10-23) Powered Roller Cut Off Override.png|alt=BE-SL and BE-DS Powered Roller Cut Off Override|frameless|180x180px]]
|'''Powered Roller Cutout Override (If equipped)'''
|-
![[File:IOP-400 BE-SL&DS (10-23) Rack-Level-Assist.png|alt=BE-SL and BE-DS Rack Level Assist |frameless|180x180px]]
|'''Rack Level Assist Indicator (If equipped)'''
|}
{| class="wikitable"
! rowspan="3" |[[File:IOP-400_BE-SL&DS_(10-23)_Power_Rollers_and_Arm_Travel.png.png|alt=BE-SL & DS Powered Roller and Arm Travel Controls|frameless|504x504px]]
|'''Far Power Rollers'''
|-
|'''Arm Travel'''
|-
|'''Near Power Rollers'''
|}
{| class="wikitable"
|+''BE-SL & DS UNITS ONLY''
! colspan="3" |[[File:IOP-400 BE-SL&DS (10-23) BE-SL&DS Units Platform Controls.png|alt=BE-SL & DS Specific Controls|frameless|460x460px]]
|-
|Drive Forward/Reverse
|Platform Raise/Lower
|Arm Rotation Near/Far
|}
{| class="wikitable"
|+''BE-TS & QS UNITS ONLY''
![[File:IOP-400 BE-SL&DS (10-23) BE-TS & BE-QS Platform Raise and Lower Controls.png|alt=BE-TS & BE-QS Platform Raise and Lower Controls|frameless|240x240px]]
! colspan="2" |[[File:IOP-400 BE-SL&DS (10-23)BE-TS & BE-QS Specific Controls.png|alt=BE-TS & BE-QS Specific-Controls|frameless]]
|-
|Platform Raise/Lower
|Drive Foward/Reverse
|Arm Rotation Near/Far
|}

= <big>General Information</big> =
== <big>Specification Data</big> ==
[[File:IOP-400 BE-SL&DS (10-23) Specification Data.png|alt=IOP-400 BE-SL&DS (10-23) Specification Data|frameless|778x778px]]
{| class="wikitable"
! colspan="2" |NOTE: SINGLE LEVEL MACHINE SHOWN
!BE-24-2
!BE-36-2
!BE-42-2
|-
!A
|Overall Length
|130"
|154"
|166"
|-
!B
|Overall Width
|72"
|72"
|74"
|-
!C
|Overall Height (Single Level / Double Stack)
|65" / 90"
|65" / 90"
|65" / 90"
|-
!D
|Wheel Base
|95.75"
|119.75"
|131.75"
|-
!E
|Drive Wheel Center line
|53"
|53"
|53"
|-
!F
|Battery Compartment Width
|24"
|36"
|42"
|-
!G
|Ground Clearance
|.625"
|.625"
|.625"
|-
!H
|Minimum Roller Height
|6.5"
|6.5"
|6.5"
|-
!I
|Maximum Roller Height (Single Level / Double Stack)
|26.5" / 56"
|26.5" / 56"
|26.5" / 56"
|-
!J
|Aisle Requirement
|78"
|78
|80"
|}

=== <big>Single Level</big> ===
{| class="wikitable"
!SPECIFICATIONS (IMPERIAL / METRIC)
!BE-24-2-SL
!BE-36-2-SL
!BE-42-2-SL
|-
|TRAVEL SPEED
|0 to 190 ft/min / 0 to 0.97 m/s
|0 to 190 ft/min / 0 to 0.97 m/s
|0 to 190 ft/min / 0 to 0.97 m/s
|-
|RAISE - LOWER SPEED
|0 to 10 ft/min / 0 to 0.05 m/s
|0 to 10 ft/min / 0 to 0.05 m/s
|0 to 10 ft/min / 0 to 0.05 m/s
|-
|POWERED ROLLER SPEED
|0 to 37 ft/min / 0 to 0.19 m/s
|0 to 37 ft/min / 0 to 0.19 m/s
|0 to 37 ft/min / 0 to 0.19 m/s
|-
|ARM TRAVERSE SPEED
|0 to 20 ft/min / 0 to 0.10 m/s
|0 to 20 ft/min / 0 to 0.10 m/s
|0 to 20 ft/min / 0 to 0.10 m/s
|-
|ARM ROTATION TIME
|6 s to 8 s
|6 s to 8 s
|6 s to 8 s
|-
|DRAW BAR PULL / VACUUM

(12” / 305 MM ROUND CUP)
|1,000 lb / 454 kg
|1,000 lb / 454 kg
|1,000 lb / 454 kg
|-
|DRAW BAR PULL MAGNET*
|800 lb to 1,200 lb / 363 kg to 544 kg
|800 lb to 1,200 lb / 363 kg to 544 kg
|800 lb to 1,200 lb / 363 kg to 544 kg
|-
|VACUUM ATTACH TIME
|< 1 s
|< 1 s
|< 1 s
|-
|VACUUM RELEASE TIME
|< 1 s
|< 1 s
|< 1 s
|-
|INPUT VOLTAGE
|240/480 V / 3 ph / 60Hz
|240/480 V / 3 ph / 60Hz
|240/480 V / 3 ph / 60Hz
|-
|AC CURRENT DRAW
|20.2 / 10.1 A
|20.2 / 10.1 A
|20.2 / 10.1 A
|-
|AC CURRENT DRAW W/ ELECTRIC

DRIVE OPTION
|31.8 / 15.9 A
|31.8 / 15.9 A
|31.8 / 15.9 A
|-
|CONTROL CIRCUIT VOLTAGE
|120 V ac
|120 V ac
|120 V ac
|-
|HYDRAULIC POWER UNIT
|5 hp / 3.73 kW
|5 hp / 3.73 kW
|5 hp / 3.73 kW
|-
|HYDRAULIC POWER UNIT W/ ELECTRIC DRIVE OPTION
|8 hp / 5.97 kW
|8 hp / 5.97 kW
|8 hp / 5.97 kW
|-
|HYDRAULIC PUMP
|8 gal/min / 30 L/min
|8 gal/min / 30 L/min
|8 gal/min / 30 L/min
|-
|POWER UNIT
|Hydraulic, Variable Displacement
|Hydraulic, Variable Displacement
|Hydraulic, Variable Displacement
|-
|OPERATING PRESSURE
|1,500 psi / 103 bar
|1,500 psi / 103 bar
|1,500 psi / 103 bar
|-
|VACUUM PUMP
|1/3 hp / 0.25 kW
|1/3 hp / 0.25 kW
|1/3 hp / 0.25 kW
|-
|VACUUM
|21” Hg / 711 mbar
|21” Hg / 711 mbar
|21” Hg / 711 mbar
|-
|FULL LOAD CAPACITY
|10,000 lb / 4535 kg
|10,000 lb / 4535 kg
|10,000 lb / 4535 kg
|-
|WEIGHT (EMPTY)
|5,800 lb / 2631 kg
|6,200 lb / 2812 kg
|7500 lb / 3402 kg
|-
|TOTAL COMPARTMENT

ROLLERS / POWERED
|11/5
|11/5
|11/5
|-
|GUIDE TRACK
|2” x 2.5” Angle / 51 mm x 64 mm
|2” x 2.5” Angle / 51 mm x 64 mm
|2” x 2.5” Angle / 51 mm x 64 mm
|-
|OVERALL DIMENSIONS (L X W X H)
|130” x 72” x 70” /

3302 mm x 1829 mm x 1778 mm
|154” x 72” x 70” /

3912 mm x 1829 mm x 1778 mm
|171” x 74” x 70” /

4343 mm x 1880 mm x 1778 mm
|-
|VACUUM ARM REACH
|4.5” to 14” / 114 mm to 356 mm
|4.5” to 14” / 114 mm to 356 mm
|4.5” to 14” / 114 mm to 356 mm
|-
|VACUUM ARM REACH (HYDRAULIC EXTENSION) TRUCK SIDE
|9” to 23” / 229 mm to 584 mm
|9” to 23” / 229 mm to 584 mm
|9” to 23” / 229 mm to 584 mm
|-
|MAGNET ARM REACH (HYDRAULIC EXTENSION) TRUCK SIDE
|14” to 22” / 355 mm to 559 mm
|14” to 22” / 355 mm to 559 mm
|14” to 22” / 355 mm to 559 mm
|-
|WHEEL BASE
|95.75” / 2432 mm
|119.75” / 3042 mm
|134.5” / 3416 mm
|-
|DRIVE WHEEL CENTERLINE
|53” / 1346 mm
|53” / 1346 mm
|53” / 1346 mm
|-
|BATTERY COMPARTMENT WIDTH
|24” / 610 mm
|36” / 914 mm
|42” / 1067 mm
|-
|MAXIMUM BATTERY DIMENSIONS

(L X W X H)
|48” x 23” x 36” /

1219 mm x 584 mm x 914 mm
|48” x 35” x 36” /

1219 mm x 889 mm x 914 mm
|48” x 41” x 36” /

1219 mm x 1041 mm x 914 mm
|-
|MINIMUM BATTERY WIDTH

(WITH VACUUM / MAGNET)
|12” / 305 mm

6” / 152 mm
|12” / 305 mm

6” / 155 mm
|12” / 305 mm

6” / 155 mm
|-
|MINIMUM BATTERY LENGTH
|16.5” / 419 mm
|16.5” / 419 mm
|16.5” / 419 mm
|-
|MINIMUM BATTERY HEIGHT
|17.75” / 451 mm
|17.75” / 451 mm
|17.75” / 451 mm
|-
|GROUND CLEARANCE
|0.63” / 16 mm
|0.63” / 16 mm
|0.63” / 16 mm
|-
|ROLLER HEIGHT
|6.5” Min / 26.5" Max

165 mm Min / 673 mm Max
|6.5” Min / 26.5" Max

165 mm Min / 673 mm Max
|6.5” Min / 26.5" Max

165 mm Min / 673 mm Max
|}

=== <big>Double-Stack</big> ===
{| class="wikitable"
!SPECIFICATIONS (IMPERIAL / METRIC)
!BE-24-2-DS
!BE-36-2-DS
!BE-42-2-DS
|-
|TRAVEL SPEED
|0 to 190 ft/min / 0.97 m/s
|0 to 190 ft/min / 0.97 m/s
|0 to 190 ft/min / 0.97 m/s
|-
|RAISE - LOWER SPEED
|0 to 16 ft/min / 0 to 0.08 m/s
|0 to 16 ft/min / 0 to 0.08 m/s
|0 to 16 ft/min / 0 to 0.08 m/s
|-
|POWERED ROLLER SPEED
|0 to 37 ft/min / 0 to 0.19 m/s
|0 to 37 ft/min / 0 to 0.19 m/s
|0 to 37 ft/min / 0 to 0.19 m/s
|-
|ARM TRAVERSE SPEED
|0 to 20 ft/min / 0 to 0.10 m/s
|0 to 20 ft/min / 0 to 0.10 m/s
|0 to 20 ft/min / 0 to 0.10 m/s
|-
|ARM ROTATION TIME
|6 s to 8 s
|6 s to 8 s
|6 s to 8 s
|-
|DRAW BAR PULL / VACUUM

(12” / 305 MM ROUND CUP)
|1,000 lb / 454 kg
|1,000 lb / 454 kg
|1,000 lb / 454 kg
|-
|DRAW BAR PULL MAGNET*
|800 lb to 1,200 lb / 363 kg to 544 kg
|800 lb to 1,200 lb / 363 kg to 544 kg
|800 lb to 1,200 lb / 363 kg to 544 kg
|-
|VACUUM ATTACH TIME
|< 1 s
|< 1 s
|< 1 s
|-
|VACUUM RELEASE TIME
|< 1 s
|< 1 s
|< 1 s
|-
|INPUT VOLTAGE
|240/480 V / 3 ph / 60Hz
|240/480 V / 3 ph / 60Hz
|240/480 V / 3 ph / 60Hz
|-
|AC CURRENT DRAW
|20.2 / 10.1 A
|20.2 / 10.1 A
|20.2 / 10.1 A
|-
|AC CURRENT DRAW W/ ELECTRIC

DRIVE OPTION
|31.8 / 15.9 A
|31.8 / 15.9 A
|31.8 / 15.9 A
|-
|CONTROL CIRCUIT VOLTAGE
|120 V ac
|120 V ac
|120 V ac
|-
|HYDRAULIC POWER UNIT
|5 hp / 3.73 kW
|5 hp / 3.73 kW
|5 hp / 3.73 kW
|-
|HYDRAULIC POWER UNIT W/ ELECTRIC DRIVE OPTION
|8 hp / 5.97 kW
|8 hp / 5.97 kW
|8 hp / 5.97 kW
|-
|HYDRAULIC PUMP
|8 gal/min / 30 L/min
|8 gal/min / 30 L/min
|8 gal/min / 30 L/min
|-
|POWER UNIT
|Hydraulic, Variable Displacement
|Hydraulic, Variable Displacement
|Hydraulic, Variable Displacement
|-
|OPERATING PRESSURE
|1,500 PSI / 103 bar
|1,500 PSI / 103 bar
|1,500 PSI / 103 bar
|-
|VACUUM PUMP
|1/3 hp / 0.25 kW
|1/3 hp / 0.25 kW
|1/3 hp / 0.25 kW
|-
|VACUUM
|21” Hg / 711 mbar
|21” Hg / 711 mbar
|21” Hg / 711 mbar
|-
|FULL LOAD CAPACITY
|10,000 lb / 4535 kg
|10,000 lb / 4535 kg
|10,000 lb / 4535 kg
|-
|WEIGHT (EMPTY)
|6,000 lb / 2722 kg
|6,600 lb / 2994 kg
|7,800 lb / 3538 kg
|-
|TOTAL COMPARTMENT

ROLLERS / POWERED
|11/5
|11/5
|11/5
|-
|GUIDE TRACK
|2” x 2.5” Angle

51 mm x 64 mm
|2” x 2.5” Angle

51 mm x 64 mm
|2” x 2.5” Angle

51 mm x 64 mm
|-
|OVERALL DIMENSIONS (L X W X H)
|130” x 72” x 92”

3302 mm x 1829 mm x 2337 mm
|154” x 72” x 92”

3912 mm x 1829 mm x 2337 mm
|171” x 74” x 92”

4343 mm x 1880 mm x 2337 mm
|-
|VACUUM ARM REACH
|4.5” to 14” / 114 to 356 mm
|4.5” to 14” / 114 to 356 mm
|4.5” to 14” / 114 to 356 mm
|-
|VACUUM ARM REACH (HYDRAULIC EXTENSION)
|9” to 23” / 229 mm to 584 mm
|9” to 23” / 229 mm to 584 mm
|9” to 23” / 229 mm to 584 mm
|-
|MAGNET ARM REACH (HYDRAULIC EXTENSION) TRUCK SIDE
|14” to 22” / 355 mm to 559 mm
|14” to 22” / 355 mm to 559 mm
|14” to 22” / 355 mm to 559 mm
|-
|WHEEL BASE
|95.75” / 2432 mm
|119.75” / 3042 mm
|134.5” / 3417 mm
|-
|DRIVE WHEEL CENTERLINE
|53” / 1346 mm
|53” / 1346 mm
|53” / 1346 mm
|-
|BATTERY COMPARTMENT WIDTH
|24” / 610 mm
|36” / 915 mm
|42” / 1067 mm
|-
|MAXIMUM BATTERY DIMENSIONS

(L X W X H)
|48” x 23” x 34”

1219 mm x 584 mm x 864 mm
|48” x 35” x 34”

1219 mm x 889 mm x 864 mm
|48” x 41” x 34”

1219 mm x 1041 mm x 864 mm
|-
|MINIMUM BATTERY WIDTH

(WITH VACUUM / MAGNET)
|12” / 305 mm

6” / 152 mm
|12” / 305 mm

6” / 152 mm
|12” / 305 mm

6” / 152 mm
|-
|MINIMUM BATTERY HEIGHT
|17.75” / 451 mm
|17.75” / 451 mm
|17.75” / 451 mm
|-
|GROUND CLEARANCE
|0.63” / 16 mm
|0.63” / 16 mm
|0.63” / 16 mm
|-
|ROLLER HEIGHT
|6.5” Min / 56” Max

165 mm Min / 1422 mm Max
|6.5” Min / 56” Max

165 mm Min / 1422 mm Max
|6.5” Min / 56” Max

165 mm Min / 1422 mm Max
|}

== <big>Pre-Installation Check</big> ==

=== <big>Floor Conditions</big> ===
The floor is the single most critical area of the battery room. A bad floor can cause significant issues with the installation as well as downtime and maintenance problems with the extractor. The floor should be verified as to its minimum thickness and strength with user. As noted on the drawing, the specific requirement of flatness for your particular type of system is listed. Below is a chart stating floor requirements. If possible, especially on double stack and higher systems, a digital level should be used to shoot the grade for compliance with the specification. The floor should also be inspected for severe cracks or excessively wide expansion joints in the travel path of the machine. If floor drains are present, they must not have a grade to the opening that encroaches into the travel path.

F-min is a rating method used to evaluate the flatness and levelness of a floor designated as "defined travel path". For example, an F-min rating of 60 means that there is no more than .129" of variation in the transverse axis (wheels left to right) and .287" variation in the longitudinal axis (front to back) on the equipment.

To avoid potential damage to drive wheel assemblies, guide track, structural components, guide rollers and issues with the inner frame equalization the "defined travel path" of the Battery Extractor should meet or exceed the recommended F-min specification. See chart below for the model specifications
{| class="wikitable"
!Model
!F-Min
!+/- Longitudinal
!+/- Transverse
!Slope Defect
|-
|SL, DS
|40
|.287"
|.192"
|.096"
|-
|TS
|60
|.186"
|.129"
|.066"
|-
|QS
|85
|.131"
|.091"
|.047"
|}
[[File:IOP-400 BE-SL&DS (10-23) Floor Conditions Pre-Installation Check.png|alt=IOP-400 BE-SL&DS (10-23) Floor Conditions Pre-Installation Check|frameless|500x500px]]

== <big>Operating Controls & Instructions</big> ==

=== <big>Operating Controls</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Operator Console.png|alt=BE-SL Operator Console|frameless|1080x1080px]]

'''''NOTE''''': Safety devices for the machine and the machine operating area SHALL NOT be rendered inoperable or misused.

Typical BE-SL operator console shown above. Position of BE-DS and/or optional controls may vary from that shown depending on age of unit and/or combination of optional controls present.

HMI display standard on units shipped after February, 2020 for Industrial Internet of Things (IIoT) package.

==== <big>Safety Features</big> ====
Key Switch – Located on the dash (see [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Operating_Controls Operating Controls]above). Primary on/off switch to prevent unauthorized personnel from operating the BE.

Emergency Stop – Located on the dash (see [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Operating_Controls Operating Controls] above). Will stop all functions immediately, locking all hydraulics in place. To

use, press down on the red button. The machine key must be used to reset the emergency stop.

Foot Switch – Must be depressed to operate the BE. Stepping off the foot switch will stop all functions immediately, locking all hydraulics in place. To resume use, depress the foot switch.

Gate Switch – The gate must be fully closed for the BE to operate.

Extractor Arm Switch – Does not permit the machine to move forward or backward unless the extractor arm is located in the center of the carriage between the indicating arrows located on the arm guard.

Powered Roller Cutout (PRC-1 or PRC-2) (I''f equipped'') – Disengages the powered roller function when the photo eye positioned on the edge of the BE battery compartment is disrupted by a battery, requiring additional input from the operator. Pressing the "Power Roller Cutout" override button (see [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Operating_Controls Operating Controls]above) on the dash will resume powered roller operation when loading or unloading batteries from the BE carriage.

Horn (''If equipped'') – Button located on the dash (see [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Operating_Controls Operating Controls]above). Used to alert personnel before moving the BE.

Strobe Light (''If equipped'') – Located on a vertical stanchion mounted to the right rear of the operator compartment. For units equipped with optional overhead guard (OHG), the beacon is located above of the operator compartment. Beacon automatically flashes when the BE is switched on to visually notify the BE is in use.

Audible Alarm (''If equipped'') – Mounted in the same location as the Strobe Light. Automatically sounds when the BE is switched on to notify personnel that the BE is in use.

Blue Light (''If equipped'') - Mounted at an elevated position on either end of the extractor which project a bright, highly concentrated blue beam pattern on the ground visually alerting personnel to the direction the extractor is moving.

=== <big>Operation Overview</big> ===

* All operators should be familiar with the operator console of the extractor before performing any battery changes. The controls of the console are simple and well marked. It consists of six, manually operated, hydraulic control valves and a three position selector switch which controls the left and right vacuum cups (or optional magnets).
* The operator shall make certain there are no persons or obstacles in the extractor path prior to traveling forward or reverse.
* All manual valves are moved in the direction of the function travel which it controls with exception of the lift/lower valve, which is pulled toward the operator for "up" and pushed away for "down."
* In the event of any failure or malfunction, step off the dead-man switch or press the E-stop button and all functions will stop immediately, locking all hydraulics in place.
* The extractor arm must be in the center of the carriage or the unit will not travel forward or reverse.
* To ensure smooth operation, all valve movements should be made in a slow, deliberate motion.
* Only one key should be provided to operate the extractor.
* When leaving the machine, the operator shall turn off the key switch, remove the key and logout out of the IIoT (if equipped) to prevent unauthorized use
* Ensure all the batteries and cables are properly stored in the battery stands prior to moving the BE.
* The BE is designed to carry only one battery in each compartment on the carriage.
* When loading the BE, position the batteries in the center of the compartments on the powered rollers to prevent any battery movement when transporting.
* Ensure there are no projections outside of the carriage before moving the BE.

=== <big>Operating Instructions</big> ===

==== <big>Pre-Change Out Preparation</big> ====
1. Position lift truck for change out in designated area.

2. Remove all battery restraints and disconnect battery cables following manufacturers guidelines. (Be sure to position battery cables so as not to be damaged by the battery during change out.)

3. Board battery extractor and close safety gate. (Gate must be fully closed or unit will not operate.)

4. Turn key switch to "ON" position.

5. Log in on the HMI display (if equipped with BE-IIoT package).

6. Depress foot pedal.

==== <big>Discharged Battery Removal</big> ====
1. Move extractor forward or reverse to position center of empty compartment with center of lift truck battery compartment. (Lead roller of extractor is equipped with a centering groove. Users may find it beneficial to mark center of lift truck compartment to aid in alignment.)

2. Align extractor's roller compartment height with lift truck's battery compartment.

3. Rotate extractor arm into battery compartment aligned in Step 2.

4. Move extractor arm toward battery until vacuum cup/magnet contacts battery

[[File:NOTICE-warn.png|alt=NOTICE|frameless|120x120px]] '''DO NOT force cup/magnet into battery after initial contact with battery is made.'''

5. Energize vacuum/magnet by turning selector switch to proper direction, left or right.

6. Move extractor arm away from lift truck toward center of extractor roller bed, removing discharged battery. (Battery should be pulled past first three idler rollers onto first or second powered roller.)

7. Turn off vacuum/magnet and move extractor arm away from battery 1" to 2".

8. Rotate extractor arm out of battery compartment into opposite compartment (if empty) and center arm in carriage.

9. Move battery into center of compartment using powered rollers.

==== <big>Charged Battery Retrieval</big> ====
1. Locate charged battery for appropriate type of lift truck being changed.

2. Raise battery extractor roller compartment to proper level to gain access as needed to disconnect desired battery from its charger and disengage battery safety stop.

[[File:WARNING-warn.png|alt=WARNING|frameless|120x120px]] '''ALWAYS be sure charging has been completed and charger is not still charging battery. Dangerous sparking/arcing can occur if battery is unplugged from charger while charging.'''

3. Move extractor to appropriate rack position and align empty roller compartment with the center of the battery storage rack compartment. ''(The battery safety stop of each compartment is the center of that compartment and should be used for alignment with the groove in the lead roller of the battery extractor compartment.)''

4. Rotate arm into empty compartment (if not already positioned there.)

5. Move extractor arm toward battery until vacuum cup/magnet contacts battery.

6. Energize vacuum cup/magnet by turning selector switch to proper direction, left or right.

[[File:NOTICE-warn.png|alt=NOTICE|frameless|120x120px]] '''DO NOT force cup/magnet into battery after initial contact with battery is made.'''

7. Move extractor arm away from battery rack toward center of extractor roller bed, removing charged battery. (Battery should be pulled past first three idler rollers onto first or second powered roller.)

8. Turn off vacuum/magnet and move extractor arm away from battery 1" to 2".

9. Rotate extractor arm out of battery compartment into fully vertical position.

10. Move battery into center of compartment using powered rollers.

==== <big>Discharged Battery Return</big> ====
1. If required, adjust extractor compartment height to battery rack level with open battery compartment. Drive extractor to align roller compartment containing discharged battery with open battery compartment.

2. Return discharged battery to battery rack using powered rollers.

'''''NOTE:''' In most instances, batteries can be deposited into battery racks in one motion using only powered rollers. When this does not work, the battery may need slight assistance from extractor arm. To do this, rotate arm into compartment such as one would if removing battery from rack. If extractor is vacuum equipped, position top edge of cup slightly higher than edge of battery (or over lifting eye if so equipped) to prevent cup from adhering to battery - No vacuum/magnet is necessary for pushing. DO NOT activate vacuum/magnet switch. Slowly push battery into rack until fully into compartment.''

3. Engage battery safety stop and connect battery to charger as required.

==== <big>Charged Battery Installation</big> ====
1. Lower extractor to fully lowered position.

2. Drive extractor back to lift truck and align roller compartment containing charged battery as performed in steps 1 and 2 of [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)?venotify=created#Discharged_Battery_Removal ''Discharged Battery Removal''].

3. Move charged battery toward lift truck compartment by using powered rollers, verifying precise battery alignment.

[[File:NOTICE-warn.png|alt=NOTICE|frameless|120x120px]] '''Many batteries are a tight fit into lift truck battery compartments. Care MUST be taken to ensure alignment is precise to avoid damage to battery, lift truck, and/or battery extractor.'''

4. Adjust extractor vertically as well as horizontally, if needed.

5. Insert battery into lift truck as far as possible using only the powered rollers.

6. Rotate extractor arm into compartment and SLOWLY push battery into lift truck. (Be sure to watch battery cables for interference.)

7. Return extractor arm to center of roller bed and lower extractor to fully lowered position. Drive extractor out of immediate area.

8. Turn off key switch, remove key from switch, log out on the HMI display (if equipped with BE-IIoT package) and carefully exit extractor.

9. Secure newly installed battery in lift truck and reconnect battery cables.

10. Return lift truck to service.
{|
![[File:Caution-Warning.png|alt=CAUTION|frameless|120x120px]]

|'''DO NOT drive the BE into the travel path end stops. The end stops are designed to prevent the BE from accidentally traveling beyond its designated travel path. Driving the BE into the end stops will cause the BE to stop suddenly, possibly causing damage to the end stop, the BE and/or personal injury.'''
|}

==== <big>Optional Powered Roller Cutout Operation</big> ====
Units equipped with optional Powered Roller Cutout, the powered roller override button must be depressed in addition to actuating the hydraulic valve when a battery disrupts the photo eye(s) at the edge of the battery compartments while using the powered rollers to transfer batteries on and off of the battery extractor.

==== <big>IIoT Equipped Units</big> ====
Units shipped after February, 2020 are equipped with BEIIoT (Industrial Internet of Things) package.

Operators must log in to the BE-IIoT system using the HMI (Human Machine Interface) display located on the dashboard to operate the extractor.

When finished operating the extractor, the operator should log out of the BE-IIoT to prevent unauthorized access and/ or operation of the extractor.

== <big>Manual Unloading</big> ==
'''Lockout/tagout and de-energize all equipment prior to manually unloading any battery.'''

In the event of power loss or an operational malfunction of the BE not allowing a battery to be unloaded using normal operating procedures, it is recommended a battery be removed from the BE using certified and approved vertical extraction methods and devices.
{|
|[[File:DANGER-warn.png|alt=DANGER|frameless|120x120px]]
|'''Read, understand and observe all safety warnings and procedures related to the vertical extraction device(s) being used.'''
|}
Should the status of the BE not allow for safe vertical extraction (due to position in the battery aisle or level of the inner carriage), only repairs required to safely maneuver the BE to a position allowing for safe vertical extraction should be made. Once any batteries are safely unloaded, any remaining repairs can be made.
{|
|[[File:DANGER-warn.png|alt=DANGER|frameless|120x120px]]
|'''Extreme care should be taken when working under or around equipment supporting elevated loads. Unexpected movement of the equipment could cause the load and/or equipment to fall. ALWAYS be sure devices of adequate size and strength are in place to prevent any personnel working under the elevated load from being crushed. Serious personal injury or death will occur.'''
|}
== <big>Spare Parts List</big> ==
Refer to the appropriate Spare Parts Kit (vacuum equipped units - Pt# BE-SPKV-SLDS, magnet equipped units - Pt# BESPKM- SLDS) for the list of items recommended by BHS to have on hand for BE-SL or BE-DS models to minimize any downtime due to minor breakdowns that may occur under normal operating conditions.

Use only BHS approved replacement parts.

BHS offers many replacement parts kits containing relevant or related parts when replacing certain individual parts or replacing any obsolete / upgraded parts.

BHS also offers a supplement hose kit (Pt# 80242005) which contains an assortment of hoses allowing any hose on the extractor to be replaced immediately with a temporary hose of equal length or longer. After the extractor is back up and running, the failed hose can be taken to have an exact replacement made. Once the new hose is made and installed, the temporary hose can be returned to the kit for future use.

Go to [http://www.bhs1.com/ www.bhs1.com] and click "[https://na.bhs1.com/parts.html Parts]" for all the latest parts kits and corresponding installation instructions (if applicable).

BHS recommends that a full maintenance inspection report similar to the one provided be done at least once a month. Any parts found to be excessively worn or damaged should promptly be replaced unless said parts pose a safety risk to the operator and/or extractor, in which case the unit should be removed from service until the problem(s) are remedied (See Operator's Daily Checklist.)

'''''NOTE:''''' ''Spare parts kits contain parts for the most current machine design/configuration. Due to continuous design and manufacturing updates and improvements, not all the parts in the spare parts kits may be compatible with older units. Consult factory when ordering spare or replacement parts for existing units in the field to ensure part compatibility.''

= <big>Parts Sections</big> =

== <big>Chassis</big> ==

=== <big>Equalization Components</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Chassis Equalization.png|alt= BE-SL & BE-DS Chassis Equalization|frameless|564x564px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="2" |1
|00158001-10
|CHAIN-ROLLER-#60
|
|''BE-SL Only''
|4
|-
|00158001-12
|CHAIN-ROLLER-#60
|
|''BE-DS Only''
|4
|-
|2
|43097001
|STUD-ANCHOR-5"
|
|''Upper''
|4
|-
|3
|PT0222-1
|LINK-CONNECTING-#60
|
|
|8
|-
|4
|HW0115
|WASHER-LOCK-3/4"
|
|
|4
|-
|5
|HW0017
|NUT-HEX-3/4-10
|
|
|8
|-
|6
|43097002
|STUD-ANCHOR-2"
|
|
|4
|-
|7
|HW0020
|NUT-JAM-3/4-10
|
|
|4
|}
[[File:IOP-400 BE-SL&DS (10-23) Chassis Equalization 2.png|alt= BE-SL & BE-DS Chassis Equalization Detail A|frameless|597x597px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="4" |1
|43127001
|SHAFT-EQUALIZATION
|
|''BE-24-2''
|2
|-
|43327001
|SHAFT-EQUALIZATION
|
|''BE-36-2''
|2
|-
|44327001
|SHAFT-EQUALIZATION
|
|''BE-42-2''
|2
|-
|44527001
|SHAFT-EQUALIZATION
|
|''BE-42-1''
|2
|-
|2
|PT0405
|BEARING-FLANGE-2 BOLT-1 1/2"
|
|
|4
|-
|3
|HW0502
|BOLT-HHCS-1/2-13 X 1 1/4"
|
|
|8
|-
|4
|HW0110
|WASHER-LOCK-1/2"
|
|
|8
|-
|5
|PT0224
|SPROCKET-60B12 X 1 1/2"
|
|''Keyed Inline''
|8
|-
|6
|43097006
|KEY-3/8" X 2 3/4"
|
|
|4
|-
|7
|PT0416
|COLLAR-SHAFT-1 1/2"
|
|
|4
|-
| rowspan="2" |8
|PT0503
|BEARING-FLANGED LOAD-2 1/4"
|
|''Used on units after 12/03''
|8
|-
|43026001
|BEARING-FLANGED LOAD-2 1/4" (MACHINED)
|
|''Used on units prior to 12/03''
|8
|-
|9
|HW0025
|NUT-JAM-7/8-14
|
|
|8
|-
|10
|HW0117
|WASHER-LOCK-7/8" (NOT SHOWN)
|
|''Used on units prior to 08/02''
|8
|}

=== <big>Crossbar Detail</big> ===

==== <big>''BE-SL Crossbar Mounting''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL Crossbar Mounting.png|alt=BE-SL Crossbar Mounting|frameless|607x607px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HW0515
|BOLT-HHCS-1/2-13 X 2"
|
|''Fully Threaded''
|8
|-
|2
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|8
|-
|3
|HW0110
|WASHER-LOCK-1/2"
|
|
|8
|-
|4
|HW0007
|NUT-HEX-1/2-13
|
|
|8
|}

==== <big>'''''BE-DS Crossbar Mounting'''''</big> ====
[[File:BE-DS Crossbar Mounting.png|alt=BE-DS Crossbar Mounting|frameless|534x534px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HW0515
|BOLT-HHCS-1/2-13 X 2"
|
|''Fully Threaded''
|8
|-
|2
|HW0504
|BOLT-HHCS-1/2-13 X 2"
|
|
|8
|-
|3
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|8
|-
|4
|HW0110
|WASHER-LOCK-1/2"
|
|
|16
|-
|5
|HW0007
|NUT-HEX-1/2-13
|
|
|16
|-
|6
|43717040
|STOP-CARRIAGE
|
|
|4
|}

=== <big>Lift Cylinder Mounting and Connections</big> ===

==== '''<big>''BE-SL Lift Cylinder Connections''</big>''' ====
[[File:BE-SL Lift Cylinder Connections.png|alt=BE-SL Lift Cylinder Connections|frameless|582x582px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43617016
|CLEVIS
|
|
|4
|-
|2
|HW0403
|BOLT-HHCS-3/8-16 X 1 1/4"
|
|
|8
|-
|3
|HW0107
|WASHER-LOCK-3/8"
|
|
|8
|-
|4
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|8
|-
|5
|00197036
|PIN-CLEVIS
|
|
|4
|-
|6
|00197035
|PIN-CYLINDER
|
|
|4
|-
|7
|HW1058
|PIN-HITCH
|
|
|16
|}

==== <big>''BE-DS Lift Cylinder Connections''</big> ====
[[File:BE-DS Lift Cylinder Connections.png|alt=BE-DS Lift Cylinder Connections|frameless|569x569px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|00158001-11
|CHAIN-ROLLER-#80
|
|
|4
|-
|2
|HW0014
|NUT-HEX-1-8
|
|
|8
|-
|3
|43897002
|STUD-LIFT-INNER FRAME
|
|
|4
|-
|4
|PT0204-1
|LINK-CONNECTING-#80
|
|
|8
|-
|5
|43897001
|STUD-LIFT-OUTER FRAME
|
|
|4
|-
|6
|43715006
|BRACKET-CYLINDER SUPPORT
|
|
|4
|-
|7
|HW1043
|CLAMP-CYLINDER
|
|
|4
|-
|8
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|9
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|10
|HW0143
|WASHER-FLAT-1/4"-FENDER
|
|
|12
|-
|11
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|13
|00197035
|PIN-CYLINDER
|
|
|4
|-
|14
|HW1058
|PIN-HITCH
|
|
|8
|}

=== <big>Track Guidance Arms</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Guide Arm.png|alt=BE-SL & BE-DS Guide Arm|frameless|548x548px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
! colspan="2" |NO. REQ
|-
|1
|43015011
|GUIDE ARM WELDMENT, 2 ROLLER
|
|
|2
|<nowiki>-</nowiki>
|-
|2
|41215204
|GUIDE ARM WELDMENT, 4 ROLLER
|
|
|<nowiki>-</nowiki>
|2
|-
|3
|43012007
|CAM ROLLER-1 3/4"
|
|
|4
|8
|-
|4
|HW0115
|WASHER-LOCK-3/4"
|
|
|4
|8
|-
|5
|HW0011
|NUT-HEX-3/4-16
|
|
|4
|8
|-
|6
|HW0505
|BOLT-HHCS-1/2-13 X 3-1/2"
|
|
|4
|6
|-
|7
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|4
|6
|-
|8
|HW0110
|WASHER-LOCK-1/2"
|
|
|4
|6
|-
|9
|HW0007
|NUT-HEX-1/2-13
|
|
|4
|6
|-
|10
|41215234
|GUIDE ARM WELDMENT (POLY)
|
|
|2
|<nowiki>-</nowiki>
|-
|11
|41217317
|POLY SLIDE MOUNTING BLOCK
|
|
|4
|<nowiki>-</nowiki>
|-
|12
|41217318
|POLY SLIDE
|
|
|4
|<nowiki>-</nowiki>
|-
|13
|HW0501
|BOLT-HHCS-1/2-13 X 1"
|
|
|12
|<nowiki>-</nowiki>
|-
|14
|HW0110
|WASHER-LOCK-1/2"
|
|
|12
|<nowiki>-</nowiki>
|-
|15
|91253A546
|BOLT FHSCS-1/4-20 X 1-1/2"
|
|
|8
|<nowiki>-</nowiki>
|-
|16
|HW0003
|NUT-NILN-1/4-20
|
|
|8
|<nowiki>-</nowiki>
|-
! colspan="7" |NOTES
|-
| colspan="7" |''† Multiple styles of Guide Arms have been utilized on extractors. Refer to the parts diagrams for correct replacement parts.''
|}

=== '''<big>Roller Bed Components</big>''' ===

==== <big>''Idler Roller Bed Components''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Idler Rollers.png|alt=BE-SL & BE-DS Idler Rollers|frameless|600x600px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="3" |1
|43182001
|LEAD ROLLER ASSEMBLY-24"
|
|with Alignment Groove
|4
|-
|43382001
|LEAD ROLLER ASSEMBLY-36"
|
|with Alignment Groove
|4
|-
|43482001
|LEAD ROLLER ASSEMBLY-42"
|
|with Alignment Groove
|4
|-
| rowspan="3" |2
|43182002
|IDLER ROLLER ASSEMBLY-24"
|
|
|8
|-
|43382002
|IDLER ROLLER ASSEMBLY-36"
|
|
|8
|-
|43482002
|IDLER ROLLER ASSEMBLY-42"
|
|
|8
|-
| rowspan="3" |3
|43187002
|SHAFT-HEX-.75" X 25.75"
|
|
|8
|-
|43387002
|SHAFT-HEX-.75" X 37.75"
|
|
|8
|-
|43487002
|SHAFT-HEX-.75" X 43.75"
|
|
|8
|-
| rowspan="3" |4
|43187003
|SHAFT-HEX-.75" X 27.5"
|
|
|4
|-
|43387003
|SHAFT-HEX-.75" X 39.5"
|
|
|4
|-
|43487003
|SHAFT-HEX-.75" X 45.5"
|
|
|4
|-
|5
|HW1058
|PIN-HITCH
|
|
|24
|}

==== <big>'''''Powered Roller Bed Components'''''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Powered Rollers 1.png|alt=Powered Rollers|frameless|554x554px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="3" |1
|43182003
|POWERED ROLLER-24"
|
|
|10
|-
|43382003
|POWERED ROLLER-36"
|
|
|10
|-
|43485003
|POWERED ROLLER-42"
|
|
|10
|-
|2
|43087001
|JOURNAL-POWERED ROLLER
|
|
|10
|-
|3
|PT0404
|FLANGE BEARING-3-BOLT-1"
|
|
|20
|-
|4
|HW0321
|BOLT-HHCS-5/16-18 X 1 1/4"
|
|
|60
|-
|5
|HW0105
|WASHER-LOCK-5/16"
|
|
|60
|-
|6
|HW0004
|NUT-HEX-5/16-18
|
|
|60
|-
|7
|PT0033
|SPROCKET-35B18 X 1"
|
|
|16
|-
|8
|00197028
|KEY-1/4" X 1 1/4"
|
|
|8
|-
|9
|00158001-16
|CHAIN-ROLLER-#35
|
|
|8
|-
|10
|PT0031
|LINK-CONNECTING-#35
|
|
|8
|-
|11
|PT0418
|COLLAR-SHAFT-1"
|
|
|10
|}
[[File:IOP-400 BE-SL&DS (10-23) Powered Rollers 2.png|alt=Powered Rollers|frameless|524x524px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0120
|MOTOR-HYDRAULIC-160CC
|
|
|2
|-
|2
|HW1071
|KEY-WOODRUFF-#808 STD
|
|Supplied with Item 1
|A/R
|-
|3
|H1544
|ADAPTER-#6 JICM X #10 SAEM
|
|
|4
|-
|4
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|18
|-
|5
|HW0107
|WASHER-LOCK-3/8"
|
|
|18
|-
|6
|43017004
|PLATE-MOTOR MOUNTING
|
|
|2
|-
|7
|PT0302-1
|COUPLING BODY-#40 X 1"
|
|
|4
|-
|8
|PT0301
|CHAIN-COUPLING-#40
|
|Includes Connecting Pin
|2
|-
|9
|00197026
|KEY-1/4" X 1"
|
|
|2
|-
|10
|43097003
|KEY-1/4" X 5/8"
|
|
|2
|}

=== <big>Operator Gate</big> ===

==== <big>''[Discontinued] Drop Bar Operator Gate''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Drop Bar Barrier Gate.png|alt=Discontinued Drop Bar Operator Gate|frameless|565x565px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43015004
|GATE-OPERATOR-DROP BAR
|
|
|1
|-
|2
|HW0407
|BOLT-HHCS-3/8-16 X 2 3/4"
|
|
|1
|-
|3
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|2
|-
|4
|HW0006
|NUT-NILN-3/8-16
|
|
|1
|}

==== <big>'''''[Current] Swing-Style Operator Gate'''''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Operator Gates.png|alt=Operator Gate Styles|frameless|500x500px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43017064-2
|LATCH-SWING GATE
|
|
|1
|-
|2
|HW0418
|BOLT-HHCS-3/8-16 X 2 1/4"
|
|
|1
|-
|3
|HW0031
|NUT-LOCK-3/8-16, DEFORMED THREAD
|
|
|1
|-
|4
|N/A
|HINGE-SPRING
|
|''† See notes''
|1
|-
|5
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|3
|-
|6
|HW1037
|STOP-GATE
|
|
|1
|-
|7
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|1
|-
|8
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|1
|-
|9
|HW0003
|NUT-NILN-1/4-20
|
|
|1
|-
|10
|N/A
|SPRING-TORSION
|
|''† See notes''
|1
|-
|11
|HW0816
|SCREW-HHCS-SELF DRILLING-#10 X 3/4"
|
|
|4
|-
|12
|HW9002
|GAS SPRING
|80292015
|
|1
|-
|13
|43017086-2
|BRACKET-MOUNTING-SPRING
|80292015
|
|2
|-
|14
|HW0815
|SCREW-SELF DRILLING-#12-24 X 1" T-4
|80292015
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Part discontinued. Spring Hinge was replaced by Torsion Spring. Spring Hinge and/or Torsion Spring must be replaced with Gas Spring Kit.''
|}

=== <big>Operator Step</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Operator Step Styles.png|alt=BE-SL & BE-DS Operator Step Styles|frameless|525x525px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="2" |1
|43615012
|STEP
|
|''† BE-SL''
|1
|-
|43015007
|STEP
|
|''† BE-DS''
|1
|-
|2
|HW0406
|BOLT-HHCS-3/8-16 X 2 1/2"
|
|
|2
|-
|3
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|4
|-
|4
|HW0107
|WASHER-LOCK-3/8"
|
|
|2
|-
|5
|HW0005
|NUT-HEX-3/8-16
|
|
|2
|-
| rowspan="2" |6
|43606001
|ANTI-FATIGUE MAT
|
|''†† BE-SL''
|1
|-
|43706001
|ANTI-FATIGUE MAT
|
|''†† BE-DS''
|1
|-
|7
|43017058-2
|THRESHOLD
|
|
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Tread-Style Step is a direct replacement for Discontinued, Ladder Rung-Style Step.''
|-
| colspan="6" |''†† Anti-fatigue mat must be cut for units with foot switch bolted in place to floor panel.''
|}

=== <big>Hydraulic Hose Reel</big> ===

==== ''<big>[Discontinued] Hydraulic Hose Reel</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Hydraulic Hose Reel.png|alt=BE-SL & BE-DS Discontinued Hydraulic Hose Reel|frameless|556x556px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|PT0622-1
|HOSE REEL
|
|
|1
|-
|2
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|1
|-
|3
|HW0107
|WASHER-LOCK-3/8"
|
|
|1
|-
|4
|HW0005
|NUT-HEX-3/8-16
|
|
|1
|-
|5
|43717053-2
|BRACKET-HOSE REEL
|
|
|1
|}

==== ''<big>[Current] Hydraulic Hose Reel</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Current Hydraulic Hose Reel.png|alt= BE-SL & BE-DS Current Hydraulic Hose Reel|frameless|688x688px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|CCR-12HD
|HOSE REEL
|
|
|1
|-
|2
|43717122
|PLATE-MOUNTING
|
|
|1
|-
|3
|HW0413
|BOLT-FHSMS-3/8-16 X 1 1/4"
|
|
|2
|-
|4
|HW0517
|BOLT-HHCS-1/2-13 X 2 1/2"-FULL THREAD
|
|
|2
|-
|5
|HW0110
|WASHER-LOCK-1/2"
|
|
|2
|-
|6
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|2
|}

=== <big>Guarding</big> ===

==== <big>'''''BE-SL Guarding'''''</big> ====

===== ''BE-SL Outer Carriage Guards'' =====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL Outside Carriage Guard.png|alt= BE-SL Outside Carriage Guards|frameless|548x548px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43617006-2
|GUARD-FAR
|
|
|1
|-
|2
|43614009
|GUARD-NEAR
|
|
|2
|-
|3
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|30
|}

===== ''BE-SL Inner Carriage Guards (Rotary Actuator)'' =====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL Rotary Actuator Units Inner Guard.png|alt=BE-SL Rotary Actuator Units Inner Guards|frameless|530x530px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43617007-2
|GUARD-INNER CARRIAGE
|
|
|2
|-
|2
|43014006-2
|GUARD-LINEAR DRIVE SCREW
|
|
|1
|-
| rowspan="2" |3
|43017010-2
|GUARD-SIDE-ARM CARRIER SHAFT
|
|
|2
|-
|44517002-2
|GUARD-SIDE-ARM CARRIER SHAFT
|
|''† Single Compartment Units Only''
|1
|-
|4
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|32
|-
|5
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|4
|-
|6
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|7
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|8
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|9
|PL0602
|VINYL EDGING
|
|''6ft each for Item 3 (Not shown)''
|12'
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Single Compartment Guard Replaces standard, Far Side Arm Carrier Shaft Guard.''
|}

===== ''BE-SL Inner Carriage Guards (Helical Actuator)'' =====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL Helical Actuator Equipped Units Inner Guard.png|alt=BE-SL Helical Actuator Equipped Units Inner Guards|frameless|526x526px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43617007-2
|GUARD-INNER CARRIAGE
|
|
|2
|-
| rowspan="2" |2
|43017081-2
|GUARD-SIDE-ARM CARRIER SHAFT
|
|
|2
|-
|44517003-2
|GUARD-SIDE-ARM CARRIER SHAFT
|
|''† Single Compartment Units Only''
|1
|-
|3
|43017080-2
|BRACKET-SIDE GUARD MOUNTING
|
|
|2
|-
|4
|43017082-3
|MOUNT-CHAIN GUARD-LEAD SCREW
|
|
|1
|-
|5
|43017082-4
|MOUNT-CHAIN GUARD-LEAD SCREW
|
|
|1
|-
|6
|43017083-2
|GUARD-CHAIN-LEAD SCREW
|
|
|1
|-
|7
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|8
|HW0103
|WASHER-LOCK-1/4"
|
|
|8
|-
|9
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|8
|-
|10
|HW0347
|BOLT-BHSCS-1/4-20 X 3/8"
|
|
|4
|-
|11
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|26
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Single Compartment Guard replaces standard, Far Side Arm Carrier Shaft Guard.''
|}

==== <big>''BE-SL Dashboard Guards''</big> ====

===== ''[Discontinued] BE-SL Dashboard'' =====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued BE-SL Dashboard.png|alt=Discontinued BE-SL Dashboard|frameless|528x528px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43617038
|DASHBOARD
|
|''Used prior to October 2012''
|1
|-
|2
|43617039
|COVER PLATE
|
|
|2
|-
|3
|SS0104
|BOLT-SHCS-1/4-20 X 5/8"
|
|''Used prior to October 2012''
|18
|-
|4
|SS0300
|WASHER-FLAT-1/4"-SAE
|
|''Used prior to October 2012''
|18
|-
|5
|43614006-2
|KICK PLATE-OPERATOR CONSOLE
|
|
|1
|-
|6
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|14
|-
|7
|PL0602
|VINYL EDGING
|
|''Two 1ft pieces (Not shown)''
|2'
|}

===== ''[Current] BE-SL Dashboard'' =====
[[File:IOP-400 BE-SL&DS (10-23) Current BE-SL Dashboard.png|alt=Current BE-SL Dashboard|frameless|526x526px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43618017
|PLATE-DASHBOARD
|
|
|1
|-
|2
|HW0060
|NUT-CLIP-#10-24
|
|
|10
|-
|3
|SS0114
|BHSCS-#10-24 X 1/2" SST
|
|
|10
|-
|4
|43617039
|COVER PLATE
|
|
|2
|-
|5
|SS0126
|BHSCS-1/4-20 X 1/2"-SST
|
|
|8
|-
|6
|43614006-2
|KICK PLATE-OPERATOR CONSOLE
|
|
|1
|-
|7
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|10
|-
|8
|PL0602
|VINYL EDGING
|
|''Two 1ft pieces (Not shown)''
|2'
|}

==== ''<big>BE-SL Operator Platform Guards</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL Operator Platform Guards.png|alt=BE-SL Operator Platform Guards|frameless|591x591px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43617045
|PANEL-OPERATOR PLATFORM
|
|
|1
|-
|2
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|8
|-
|3
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|8
|-
|4
|HW0103
|WASHER-LOCK-1/4"
|
|
|8
|-
|5
|HW0002
|NUT-HEX-1/4-20
|
|
|8
|-
|6
|43606001
|MAT-ANTI FATIGUE
|
|''Not shown''
|1
|}

=== <big>'''BE-DS Guarding'''</big> ===

==== <big>'''''BE-DS Outer Carriage Guards'''''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-DS Outside Carriage Guards.png|alt=BE-DS Outside Carriage Guards|frameless|523x523px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43717017-2
|GUARD-FAR END-UPPER
|
|
|1
|-
|2
|43717019-2
|GUARD-FAR END-LOWER
|
|
|1
|-
|3
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|22
|}

==== ''BE-DS Inner Carriage Guards (Rotary Actuator)'' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-DS Rotary Actuator Equipped Units Inner Guards.png|alt=BE-DS Rotary Actuator Equipped Units Inner Guards|frameless|530x530px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43714001-2
|DASHBOARD
|
|''† See Notes''
|1
|-
| rowspan="2" |2
|43714016-2
|GUARD-FRONT-OPERATOR CONSOLE
|
|''†† Without Cylinder Notch''
|1
|-
|41217014-2
|GUARD-FRONT-OPERATOR CONSOLE
|
|''†† With Cylinder Notch''
|1
|-
|3
|43717016-2
|GUARD-INNER FRAME
|
|
|2
|-
|4
|43014006-2
|GUARD-LINEAR DRIVE SCREW
|
|
|1
|-
|5
|43017010-2
|GUARD-SIDE-ARM CARRIER SHAFT
|
|
|2
|-
|5a
|PL0602
|VINYL EDGING
|
|''6' each for Item 5 (Not shown)''
|12'
|-
| rowspan="2" |6
|43714015-2
|KICK PLATE-OPERATOR CONSOLE
|
|''35.5" tall''
|1
|-
|43717115-2
|KICK PLATE-OPERATOR CONSOLE
|
|''29" tall''
|1
|-
|6a
|PL0602
|VINYL EDGING
|
|''Two 1' pieces for Item 6 (Not shown)''
|2'
|-
|7
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|56
|-
|8
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|4
|-
|9
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|10
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|11
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|12
|PL0602
|VINYL EDGING
|
|''8' each for Item 3 (Not shown)''
|16'
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Used on units shipped prior to October, 2012. See Current BE-DS Dashboard in the Guarding Section for units shipped after October 2012.''
|-
| colspan="6" |''†† 43714016-2 valid for units shipped prior to December 2022.''
''41217014-2 valid for units shipped December 2022 to present.''
|}

==== <big>''[Current] BE-DS Dashboard Guarding''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-DS Current Dashboard.png|alt=BE-DS Current Dashboard|frameless|530x530px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43717123-2
|FRAME-DASHBOARD
|
|
|1
|-
|2
|43718017
|PLATE-DASHBOARD
|
|
|1
|-
|3
|HW0060
|NUT-CLIP-#10-24
|
|
|10
|-
|4
|SS0114
|BHSCS-#10-24 X 1/2" SST
|
|
|10
|-
|5
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|''Not shown''
|10
|}

==== ''BE-DS Inner Carriage Guards (Helical Actuator)'' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-DS-Helical Actuator Equipped Units Inner Guards.png|alt=BE-DS-Helical Actuator Units Inner Guards|frameless|526x526px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="2" |1
|43714016-2
|GUARD-FRONT-OPERATOR CONSOLE
|
|''† Without Cylinder Notch''
|1
|-
|41217014-2
|GUARD-FRONT-OPERATOR CONSOLE
|
|''† With Cylinder Notch''
|1
|-
|2
|43717016-2
|GUARD-INNER-FRAME
|
|
|2
|-
| rowspan="2" |3
|43017081-2
|GUARD-SIDE-ARM CARRIER SHAFT
|
|
|2
|-
|44517003-2
|GUARD-SIDE-ARM CARRIER SHAFT
|
|''†† Single Compartment Units Only''
|1
|-
|4
|43017080-2
|BRACKET-SIDE GUARD MOUNTING
|
|
|2
|-
|5
|43017082-3
|MOUNT-CHAIN GUARD-LEAD SCREW
|
|
|1
|-
|6
|43017082-4
|MOUNT-CHAIN GUARD-LEAD SCREW
|
|
|1
|-
|7
|43017083-2
|GUARD-CHAIN-LEAD SCREW
|
|
|1
|-
|8
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
| rowspan="2" |9
|43714015-2
|KICK PLATE-OPERATOR CONSOLE
|
|''35.5" tall''
|1
|-
|43717115-2
|KICK PLATE-OPERATOR CONSOLE
|
|''29" tall''
|1
|-
|10
|HW0103
|WASHER-LOCK-1/4"
|
|
|8
|-
|11
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|8
|-
|12
|HW0347
|BOLT-BHSCS-1/4-20 X 3/8"
|
|
|4
|-
|13
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|28
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† 43714016-2 valid for units shipped prior to December 2022.''
''41217014-2 43714016-2 valid for units shipped December 2022 to present.''
|-
| colspan="6" |''†† Single Compartment Guard replaces standard, Far Side Arm Carrier Shaft Guard.''
|}

==== <big>''BE-DS Operator Platform Guarding''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-DS Operator Platform.png|alt=BE-DS Operator Platform|frameless|587x587px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43715018
|PANEL-FLOOR
|
|''With reservoir access panel''
|1
|-
|2
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|8
|-
|3
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|8
|-
|4
|HW0103
|WASHER-LOCK-1/4"
|
|
|8
|-
|5
|HW0002
|NUT-HEX-1/4-20
|
|
|8
|-
|6
|43717022
|GRILL-HYDRAULIC COMPONENT
|
|
|1
|-
|7
|HW0403
|BOLT-HHCS-3/8-16 X 1 1/4"
|
|
|2
|-
|8
|HW0107
|WASHER-LOCK-3/8"
|
|
|2
|-
|9
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|2
|-
|10
|43706001
|MAT-ANTI FATIGUE
|
|''Not shown''
|1
|-
|11
|PL0602
|VINYL EDGING
|
|''For Item 6 (Not shown)''
|13'
|}

=== <big>Labels & Placards</big> ===

==== '''<big>''BE-SL Labels''</big>''' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL Labels.png|alt=BE-SL Labels|frameless|585x585px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|00196616
|LABEL-"NO RIDERS ALLOWED"
|
|
|1
|-
|2
|00196210
|LABEL-WARNING-"OPERATION BY AUTHORIZED PERSONNEL ONLY"
|
|
|1
|-
|3
|43696001
|PLACARD-OFF / ON
|
|
|1
|-
|4
|43096018
|PLACARD-RACK LEVEL ASSIST
|
|''† If Equipped''
|1
|-
|5
|43096014
|PLACARD-DRIVE / RAISE-LOWER / ARM ROTATION
|
|
|1
|-
|6
|43096010
|PLACARD-HORN
|
|''†'' ''If Equipped''
|1
|-
| rowspan="2" |7
|43096012
|PLACARD-VACUUM OFF / ON
|
|''Vacuum Units Only''
|1
|-
|43096011
|PLACARD-MAGNET OFF / ON
|
|''Magnet Units Only (Not shown)''
|1
|-
|8
|43096017
|PLACARD-POWERED ROLLER CUTOUT OVERRIDE
|
|''†'' ''If Equipped''
|1
|-
|9
|43096013
|PLACARD-POWERED ROLLERS / ARM TRAVERSE
|
|
|1
|-
|10
|00196004
|LABEL-CAUTION-"WATCH FOR BATTERY AND CHARGER CABLES IN TRAVEL PATH"
|
|
|1
|-
|11
|00196622
|LABEL-LIFT POINT
|
|''(2) Each end''
|4
|-
|12
|00196700
|DECAL-BHS-24"
|
|''Far End (Not shown)''
|2
|-
| rowspan="2" |13
|00196630
|LABEL-NOTICE-HYD. OIL SPEC. (AW 68)
|
|''†† See Notes''
|1
|-
|00196645
|LABEL-NOTICE-HYD. OIL SPEC. (AW 32)
|
|''††'' ''See Notes''
|1
|-
|14
|43096008
|PLACARD-"REPLACE WITH 10 AMP FUSE ONLY"
|
|''On transformer''
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Rack Level Assist (LAI), Horn and Powered Roller Cutout (PRC) are optional features. Not all units are equipped with these options.''
|-
| colspan="6" |''†† Most units shipped prior to December 2014 require AW 68 Hydraulic Oil. Some units shipped prior to December 2014 shipped with AW 32 for low temperature applications.''
|}

==== '''<big>''BE-DS Labels''</big>''' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-DS Labels.png|alt=BE-DS Labels|frameless|728x728px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|00196616
|LABEL-"NO RIDERS ALLOWED"
|
|
|1
|-
|2
|00196210
|LABEL-WARNING-"OPERATION BY AUTHORIZED PERSONNEL ONLY"
|
|
|1
|-
|3
|43696001
|PLACARD-OFF / ON
|
|
|1
|-
|4
|43096018
|PLACARD-RACK LEVEL ASSIST
|
|''†'' ''If Equipped''
|1
|-
|5
|43096014
|PLACARD-DRIVE / RAISE-LOWER / ARM ROTATION
|
|
|1
|-
|6
|43096010
|PLACARD-HORN
|
|''†'' ''If Equipped''
|1
|-
| rowspan="2" |7
|43096012
|PLACARD-VACUUM OFF / ON
|
|''Vacuum Units Only''
|1
|-
|43096011
|PLACARD-MAGNET OFF / ON
|
|''Magnet Units Only (Not shown)''
|1
|-
|8
|43096017
|PLACARD-POWERED ROLLER CUTOUT OVERRIDE
|
|''†'' ''If Equipped''
|1
|-
|9
|43096013
|PLACARD-POWERED ROLLERS / ARM TRAVERSE
|
|
|1
|-
|10
|00196004
|LABEL-CAUTION-"WATCH FOR BATTERY AND CHARGER CABLES IN TRAVEL PATH"
|
|
|1
|-
|11
|00196622
|LABEL-LIFT POINT
|
|''(2) Each end''
|4
|-
|12
|00196700
|DECAL-BHS-24"
|
|''Far End (Not shown)''
|2
|-
| rowspan="2" |13
|00196630
|LABEL-NOTICE-HYD. OIL SPEC. (AW 68)
|
|''†† See Notes''
|1
|-
|00196645
|LABEL-NOTICE-HYD. OIL SPEC. (AW 32)
|
|''†† See Notes''
|1
|-
|14
|43096008
|PLACARD-"REPLACE WITH 10 AMP FUSE ONLY"
|
|''On transformer''
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Rack Level Assist (LAI), Horn and Powered Roller Cutout (PRC) are optional features. Not all units are equipped with these options.''
|-
| colspan="6" |''†† Most units shipped prior to December 2014 require AW 68 Hydraulic Oil. Some units shipped prior to December 2014 shipped with AW 32 for low temperature applications.''
|}

==== '''<big>''Extractor Arm Labels''</big>''' ====
[[File:IOP-400 BE-SL&DS (10-23) Labels and Placards Parts.png|alt=Labels and Placards Parts|frameless|700x700px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|00196633
|LABEL-NOTICE-"IN LINE VACUUM FILTER..."
|
|''(1) per side (Vacuum Units Only)''
|2
|-
|2
|SM-1197
|LABEL-ARM POSITION ARROW
|
|
|2
|-
|3
|00196609
|LABEL-NOTICE-"ARM MUST BE POSITIONED BETWEEN ARROWS..."
|
|
|1
|-
|4
|00196602
|LABEL-NOTICE-"LUBRICATION POINTS ON UNDERSIDE"
|
|
|2
|-
|5
|00196218
|LABEL-WARNING-"ELECTRICAL VOLTAGE HAZARD"
|
|''Magnet Units Only''
|1
|-
|6
|00196238
|LABEL-WARNING-"STRONG MAGNETIC

FIELD/DO NOT USE WITH PACEMAKER"
|
|''† Magnet Units Only''
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Pacemaker Warning Label takes place of discontinued, Triangular Magnetic Field Label.''
|}

== <big>Extractor Arm</big> ==
{| class="wikitable"
!SYMBOL
!DESCRIPTION / NOTICE
!ACTUATOR DIAGRAM
|-
|[[File:IOP-400 BE-SL&DS (10-23) Rotary Actuator Symbol.png|alt=Rotary Actuator Symbol|frameless]]
|
=== '''<big>Rotary Actuator Symbol</big>''' ===
Battery Extractors shipped prior to May 2020 are equipped with Rotary Actuator Extractor Arms.
Parts Diagrams Specific to the Rotary Actuator design are indicated with the symbol.
|[[File:IOP-400 BE-SL&DS (10-23) Rotary Actuator Extractor Arm.png|alt=BE-SL & BE-DS Rotary Actuator |frameless]]
|-
|[[File:IOP-400 BE-SL&DS (10-23) Helical Actuator Symbol.png|alt=Helical Actuator Symbol|frameless]]
|
=== <big>'''Helical Actuator Symbol'''</big> ===
Battery Extractors shipped from May 2020 to Present are equipped with Helical Actuator Extractor Arms.
Parts Diagrams Specific to the Rotary Actuator design are indicated with the Helical Actuator Symbol.
|[[File:IOP-400 BE-SL&DS (10-23) Helical Actuator Extractor Arm.png|alt=BE-SL & BE-DS Helical Actuator |frameless]]
|}

=== <big>Vacuum Components & Swing Arms</big> ===

==== ''<big>Vacuum Arms (Rotary Actuator)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Vacuum Arm.png|alt=Vacuum Arm|frameless|648x648px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="2" |1
|N/A
|ARM-PUSH/PULL-30"
|
|''† Discontinued''
|1
|-
|N/A
|ARM-PUSH/PULL-36"
|
|''† Discontinued''
|1
|-
|2
|HW0509
|BOLT-HHCS-1/2-13 X 4 1/2"
|
|
|3
|-
|3
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|6
|-
|4
|HW0110
|WASHER-LOCK-1/2"
|
|
|3
|-
|5
|HW0007
|NUT-HEX-1/2-13
|
|
|3
|-
|6
|P0505
|BUSHING-RED-#6 NPT X #4 FNPT-BRASS
|
|
|2
|-
|7
|P0402
|HOSE BARB-1/4 X #4 MNPT-BRASS
|
|
|2
|-
|8
|HW0428
|STUD-VACUUM-3/8-16 X 5"
|HW-KIT-2
|
|8
|-
|9
|HW0108
|WASHER-FLAT-3/8"-SAE
|HW-KIT-2
|
|40
|-
|10
|HW1001
|SPRING-3/8"
|HW-KIT-2
|
|24
|-
|11
|HW0006
|NUT-NILN-3/8-16
|HW-KIT-2
|
|8
|-
|12
|HW0424
|NUT-JAM-3/8-16
|HW-KIT-2
|
|8
|-
|REF
|43052006
|ADJUSTABLE PUSH/PULL ARM
|
|''Includes Items 13 through 17''
|1
|-
|13
|43057034
|ARM BASE
|
|
|1
|-
|14
|43055008
|VACUUM CUP MOUNT
|
|
|2
|-
|15
|HW0523
|BOLT-HHCS-1/2-13 X 4"
|
|
|2
|-
|16
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|4
|-
|17
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† One-piece Arms no longer available. Must replace with Adjustable Arm.''
|}

==== <big>''Vacuum Cups''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Vacuum Cups.png|alt=Vacuum Cups|frameless|619x619px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="4" |A/R
|00162004
|VACUUM CUP-10" 3-PC (STANDARD)
|
|''† Includes Items 1 through 4''
| rowspan="4" |A/R
|-
|00162003
|VACUUM CUP-12" 3-PC (STANDARD)
|
|''† Includes Items 4 through 7''
|-
|00162007
|VACUUM CUP-10" 3-PC, REINFORCED
|
|''Includes Items 1,3,4 & 8''
|-
|00162005
|VACUUM CUP-12" 3-PC, REINFORCED
|
|''Includes Items 4,5,7 & 9''
|-
|1
|00164006
|CASTING-10" VACUUM CUP
|
| rowspan="3" |''10" cup only''
|1
|-
|2
|00164004
|SEAL-RUBBER-10"
|
|1
|-
|3
|00165002
|PLATE-FRONT-10"
|
|1
|-
|4
|HW0311
|BOLT-FHSCS-1/4-20 X 3/4"
|
|
|8
|-
|5
|00166001
|CASTING-12" VACUUM CUP
|
| rowspan="3" |''12" cup only''
|1
|-
|6
|00164001
|SEAL-RUBBER-12"
|
|1
|-
|7
|00165001
|PLATE-FRONT-12"
|
|1
|-
|8
|00164007
|SEAL-RUBBER-10"-REINFORCED
|
|
|A/R
|-
|9
|00167003
|SEAL-RUBBER-12"-REINFORCED
|
|
|A/R
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† 10" and 12" 1-Piece Cups no longer available. Must replace with 3-Piece Cup. Verify required cup size prior to ordering.''
|}

==== <big>''Swing Arms (Rotary Actuator)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Swing Arm Rotary Actuator.png|alt=Swing Arms (Rotary Actuator)|frameless|525x525px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="3" |1
|45055001
|TIE PLATE-SWING ARM
|
|''BE-24-2''
|1
|-
|45255001
|TIE PLATE-SWING ARM
|
|''BE-36-2 (Not shown)''
|1
|-
|45355001
|TIE PLATE-SWING ARM
|
|''BE-42-2 (Not shown)''
|1
|-
|2
|43055004
|SWING ARM-RHS
|†
|''Not sold individually''
|1
|-
|3
|43055002
|SWING ARM-LHS
|†
|''Not sold individually''
|1
|-
|4
|HW0603
|BOLT-FHSCS-5/8-11 X 2"
|
|
|4
|-
|5
|HW0113
|WASHER-LOCK-5/8"
|
|
|4
|-
|6
|HW0010
|NUT-JAM-5/8-11
|
|
|4
|-
|7
|PT0413
|COLLAR-SHAFT-3"
|80252001
|
|2
|-
|8
|43027001
|SHAFT-ROTARY ACTUATOR
|80252001
|
|1
|-
|9
|HW1013
|KEY-3/8" X 12"
|80252001
|
|1
|-
|10
|PT0419
|BEARING-SAE 841-2" I.D., 3" OD, 1/8" THICK
|80252001
|
|3
|-
|11
|43052005
|CAP-BEARING
|
|''Includes bearing''
|2
|-
|12
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|6
|-
|13
|HW0103
|WASHER-LOCK-1/4"
|
|
|6
|-
|14
|43057014
|STANDOFF-WIRE
|
|
|1
|-
|15
|HW0312
|SCREW-SHSS-1/4-20 X 1"-CUP POINT
|
|
|1
|-
|16
|43057003
|CUSHION-SWING ARM
|
|
|2
|-
|17
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|4
|-
| rowspan="2" |18
|43055001
|STOP-SWING ARM
|
|
|2
|-
|44555001
|STOP-SWING ARM
|
|''BE-42-1 only''
|1
|-
|19
|HW0403
|BOLT-HHCS-3/8-16 X 1 1/4"
|
|
|4
|-
|20
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|21
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|4
|-
|22
|H1565
|ADAPTER-45 DEG-#6 JICM X #4 NPTM
|
|
|2
|-
|23
|H1600
|ADAPTER-90 DEG-#6 JICM X #8 SAEM
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |† ''Included in multiple kits.''
|}
[[File:IOP-400 BE-SL&DS (10-23) Swing Arm Stop Rotary.png|alt= BE-SL&DS Swing Arm Stop Rotary (Rotary Actuator)|frameless|534x534px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|44555001
|STOP-SWING ARM
|
|
|1
|-
|2
|43057003
|CUSHION-SWING ARM
|
|
|1
|-
|3
|43057008
|SPACER-SWING ARM STOP
|
|
|1
|-
|4
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|2
|-
|5
|HW0403
|BOLT-HHCS-3/8-16 X 1 1/4"
|
|
|4
|-
|6
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|}

==== ''<big>Vacuum Pump (Rotary Actuator)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Vacuum Pump (Rotary Actuator).png|alt=BE-SL&DS Vacuum Pump (Rotary Actuator)|frameless|532x532px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|P0005
|PUMP-VACUUM
|
|
|1
|-
|2
|P0208
|FILTER-HI FLOW
|
|
|3
|-
|3
|P0503
|NIPPLE-#4 NPT-BRASS
|
|
|3
|-
|4
|P0502
|TEE-#4 FNPT-BRASS
|
|
|1
|-
|5
|P0506
|ELBOW-STR-90 DEG-#4 NPT-BRASS
|
|
|4
|-
|6
|P0402
|HOSE BARB-1/4 X #4 NPTM-BRASS
|
|
|6
|-
|7
|P0207
|VALVE-VACUUM RELEASE
|
|
|2
|-
|8
|P0302
|HOSE-VACUUM-1/4" I.D.
|
|''Two 6" pieces''
|1'
|-
|9
|P0302
|HOSE-VACUUM-1/4" I.D.
|
|''Short Arm side''
|1'
|-
|10
|P0302
|HOSE-VACUUM-1/4" I.D.
|
|''Long Arm side''
|2'
|-
|11
|E0611
|JUNCTION BOX-4" X 2" X 2"
|
|
|1
|-
|12
|E0612
|COVER-JUNCTION BOX
|
|
|1
|-
|13
|HW0212
|SCREW-RHMS-#10-24 X 1/2"
|
|
|2
|-
|14
|E0624
|CONNECTOR-1/2"
|
|
|1
|-
|15
|E0608-1
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .450" to .560"''
|1
|-
|15a
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|''Not shown''
|2
|-
| rowspan="2" |16
|E0501
|CORD-14-4 SW/SOW
|
|''Withtout Ground Connection in Arm''
| rowspan="2" |15'
|-
|E0514
|CORD-16-5 SW/SOW
|
|
|-
|17
|43057014
|STANDOFF-CABLE
|
|
|1
|-
|18
|HW0206
|SCREW-RHMS-#10-32 X 3/4"
|
|
|4
|-
|19
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|1
|-
|20
|43057021
|PLATE-STIFFENER
|†
|
|2
|-
|21
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|†
|
|12
|-
|22
|HW0107
|WASHER-LOCK-3/8"
|†
|
|12
|-
|23
|HW0005
|NUT-HEX-3/8-16
|†
|
|12
|-
|24
|HW0108
|WASHER-FLAT-3/8"-SAE
|†
|''Not shown''
|24
|-
|25
|P0111
|FILTER-VACUUM-INLINE
|
|''Not shown''
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |† ''Included in multiple kits.''
|}

=== <big>Rotary Actuator</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Rotary-Actuator.png|alt=BE-SL & BE-DS Rotary Actuator|frameless|523x523px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43046001
|ROTARY ACTUATOR
|
|
|1
|-
|2
|80000002
|ROTARY ACTUATOR BASE ASSEMBLY
|
|''Without Actuator''
|1
|-
|2A
|N/A
|VERTICAL CARRIER PLATE-OUTER
|
|''Included with 80000002''
|2
|-
|2B
|N/A
|VERTICAL CARRIER PLATE-INNER
|
|''Included with 80000002''
|1
|-
|2C
|N/A
|CARRIER BASE PLATE
|
|''Included with 80000002''
|1
|-
|3
|HW1070
|PIN-PULL DOWEL-5/8" X 1 1/2"
|
|
|2
|-
|4
|HW0508
|BOLT-SHCS-1/2-13 X 3/4"
|
|
|3
|-
|5
|HW1045
|PIN-PULL DOWEL-3/8" X 1 1/2"
|
|''Included with 80000002''
|6
|-
|6
|HW0412
|BOLT-SHCS-3/8-16 X 1 1/4"
|
|''Included with 80000002''
|12
|-
|7
|H0010
|FITTING-BULKHEAD-3/4-16 X #4 FNPT
|
|
|4
|-
|8
|H1579
|ADAPTER-90 DEG-#6 JICM X #4 NPTM
|
|
|2
|}

=== <big>Carrier Shafts & Bearings ''(Rotary Actuator)''</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Carrier Shafts Rotary Actuator.png|alt=BE-SL&DS Carrier Shafts (Rotary Actuator)|frameless|522x522px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43057045
|CARRIER SHAFT-EXTRACTOR ARM
|
|''† See notes''
|2
|-
|2
|43054007
|BEARING-EXTRACTOR ARM CARRIER
|80252002
|''†† See notes''
|4
|-
|3
|HW0412
|BOLT-SHCS-3/8-16 X 1 1/4"
|80252002
|
|16
|-
|4
|PT0413
|COLLAR-SHAFT-3"
|
|
|4
|-
|5
|PT0624
|FITTING-ZERK
|80252002
|''Not shown''
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† See Extended Reach End Plate section (2.6.8) for Extended Reach equipped units.''
|-
| colspan="6" |''†† See [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Carrier_Shafts_&_Bearings_(Helical_Actuator) Carrier Shafts & Bearings (Helical Actuator)] section for Helical Actuator equipped units''
|}

=== <big>Drive Screw Components ''(Rotary Actuator)''</big> ===

==== ''<big>Drive Nut Assembly (Rotary Actuator)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Drive Nut Assembly Rotary Actuator.png|alt= BE-SL&DS Drive Nut Assembly Rotary Actuator|frameless|537x537px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43054006
|DRIVE NUT ASSEMBLY
|80252003
|''†'' ''See notes''
|1
|-
|2
|HW0426
|BOLT-SHCS-3/8-16 X 5 1/2"
|80252003
|''††'' ''See notes''
|4
|-
|3
|HW0108
|WASHER-FLAT-3/8"-SAE
|80252003
|''††'' ''See notes''
|4
|-
|4
|HW0006
|NUT-NILN-3/8-16
|80252003
|''††'' ''See notes''
|4
|-
|5
|PT0624
|FITTING-ZERK
|80252003
|
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† See [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Drive_Screw_Components_(Helical_Actuator) Drive Screw Components (Helical Actuator)] section for Helical Actuator equipped units.''
|-
| colspan="6" |''†† It is recommended to replace mounting hardware when replacing Drive Nut Assembly.''
|}

==== ''<big>Drive Screw</big>'' ====

===== ''[Current] Drive Screw Assembly (Frame #'s 374 to Present)'' =====
[[File:IOP-400 BE-SL&DS (10-23) Drive Screw Rotary Current.png|alt=Current BE-SL & BE-DS Drive Screw (Rotary Actuator)|frameless|531x531px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43024001
|SCREW-LINEAR DRIVE
|
|
|1
|-
|2
|PT0119
|SPROCKET-50B15 X 1 3/16"
|
|
|1
|-
|3
|43097004
|KEY-1/4 X 7/8"
|
|
|1
|-
|4
|00158001-15
|CHAIN-ROLLER-#50
|
|
|1
|-
|5
|PT0102
|LINK-CONNECTING-#50
|
|
|1
|-
|6
|PT0406
|FLANGE BEARING-4 BOLT-1 3/16"
|
|''Alloy casting''
|2
|-
|7
|HW0503
|BOLT-HHCS-1/2-13 X 1 1/2"
|
|
|8
|-
|8
|HW0110
|WASHER-LOCK-1/2"
|
|
|8
|-
|9
|PT0107
|SPROCKET-50B15 X 1"
|
|
|1
|-
|10
|HC0121
|MOTOR-HYDRAULIC-100CC
|
|''SAE 2-Bolt mount''
|1
|-
|11
|H1605
|ADAPTER-90 DEG-#6 JICM X #10 SAEM
|
|
|2
|-
|12
|HW1071
|KEY-WOODRUFF-#808 STD
|
|''Supplied with Item 10''
|A/R
|-
|13
|HW0403
|BOLT-HHCS-3/8-16 X 1 1/4"
|
|
|6
|-
|14
|HW0107
|WASHER-LOCK-3/8"
|
|
|6
|-
|15
|43017007
|PLATE-MOUNTING-SCREW DRIVE MOTOR
|
|
|1
|-
|16
|43057019
|PLATE-COVER
|
|
|2
|-
|17
|HW0415
|BOLT-SHCS-3/8-16 X 3/4"
|
|
|8
|}
{| class="wikitable"
! colspan="6" |ITEMS BELOW ARE REQUIRED FOR REPLACING THE LINEAR DRIVE

SCREW ON UNITS WITH FRAME #'S OF 373 AND EARLIER
|-
! colspan="6" |LINEAR DRIVE SCREW UPDATE KIT
|-
|REF
|80252011
|UPGRADE KIT
|
|
|1
|-
|1
|43024001
|SCREW-LINEAR DRIVE
|
|
|1
|-
|2
|PT0119
|SPROCKET-50B15 X 1 3/16"
|
|
|1
|-
|3
|43097004
|KEY-1/4 X 7/8"
|
|
|1
|-
|6
|PT0406
|FLANGE BEARING-4 BOLT-1 3/16"
|
|''Alloy casting''
|2
|-
|7
|HW0503
|BOLT-HHCS-1/2-13 X 1 1/2"
|
|
|8
|-
|8
|HW0110
|WASHER-LOCK-1/2"
|
|
|8
|-
|16
|43057019
|PLATE-COVER
|
|
|2
|-
|18
|43057022
|SHIM-18GA
|
|''May not be required (Not shown)''
|2
|-
|19
|43057018
|TEMPLATE-BEARING MOUNT PATTERN
|
|''Not shown''
|1
|-
|20
|80000015
|INSTRUCTION DETAIL
|
|''Not shown''
|REF
|-
|21
|43057020
|SPACER PLATE
|
|''Not shown''
|2
|}

===== ''[Discontinued] Drive Screw Assembly (Frame #'s 373 and Earlier)'' =====
[[File:IOP-400 BE-SL&DS (10-23) Drive Screw (Rotary Actuator) Discontinued.png|alt=Discontinued BE-SL & BE-DS Drive Screw (Rotary Actuator)|frameless|532x532px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|N/A
|SCREW-LINEAR DRIVE (DISCONTINUED)
|
|''See 80252011 Upgrade Kit''
|1
|-
|2
|PT0118
|SPROCKET-50B12 X 1 3/16"
|
|
|1
|-
|3
|43097004
|KEY-1/4" X 7/8"
|
|
|1
|-
|4
|00158001-15
|CHAIN-ROLLER-#50
|
|
|1
|-
|5
|PT0102
|LINK-CONNECTING-#50
|
|
|1
|-
|6
|43057016
|BLOCK-BEARING RETAINER
|
|
|2
|-
|6a
|PT0414
|RACE-TAPERED ROLLER BEARING
|
|''Included with 43057016''
|2
|-
|7
|PT0623
|SEAL-GREASE
|
|
|2
|-
|8
|HW0416
|BOLT-SHCS-3/8-16 X 1"
|
|
|8
|-
|9
|PT0415
|BEARING-TAPERED ROLLER
|
|
|2
|-
|10
|HW1050
|NUT-LOCK
|
|
|4
|-
|11
|43057017
|PLATE-COVER
|
|
|2
|-
|12
|HW0415
|BOLT-SHCS-3/8-16 X 3/4"
|
|
|8
|-
|13
|PT0624
|FITTING-ZERK
|
|
|2
|}

=== <big>Hose Carrier Plate</big> ===
d[[File:IOP-400 BE-SL&DS (10-23) Hose Carrier.png|alt=BE-SL&DS Hose Carrier|frameless|557x557px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43017013
|PLATE-HOSE CARRIER
|
|
|1
|-
|2
|PT0618
|BRACKET-FIXED END
|
|
|1
|-
|3
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
|4
|PT0617
|HOSE CARRIER
|
|''20 links required''
|3'
|-
|5
|PT0619
|BRACKET-MOVING END
|
|
|1
|-
|6
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|2
|-
|7
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|8
|HW0403
|BOLT-HHCS-3/8-16 X 1 1/4"
|
|
|4
|-
|9
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|8
|-
|10
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|11
|HW0005
|NUT-HEX-3/8-16
|
|
|4
|}

=== <big>Magnet Components ''(Rotary Actuator)''</big> ===

==== ''<big>[Discontinued] Magnet Arm Configuration (Rotary Actuator)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Magnet Extraction Prior to Nov 2014 (Rotary Actuator).png|alt= BE-SL & BE-DS Magnet Extraction Prior to Nov 2014 (Rotary Actuator)|frameless|563x563px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41257014
|TIE PLATE-SWING ARM
|
|''All units''
|1
|-
|<nowiki>-</nowiki>
|41655008
|EXTENSION-ARM
|
|''BE-36-2 only (Not shown)''
|1
|-
|<nowiki>-</nowiki>
|43455001
|EXTENSION-ARM
|
|''BE-42-2 only (Not shown)''
|1
|-
|2
|HW0603
|BOLT-FHSCS-5/8-11 X 2"
|
|
|4
|-
|3
|HW0113
|WASHER-LOCK-5/8"
|
|
|4
|-
|4
|HW0010
|NUT-JAM-5/8-11
|
|
|4
|-
|5
|41655001
|CARRIER TUBE-MAGNET SWING SHAFT
|
|
|1
|-
|6
|HW0504
|BOLT-HHCS-1/2-13 X 2"
|
|
|6
|-
|7
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|6
|-
|8
|HW0110
|WASHER-LOCK-1/2"
|
|
|6
|-
|9
|HW0007
|NUT-HEX-1/2-13
|
|
|6
|-
|10
|41657006
|SHAFT-MAGNET SWING
|
|
|1
|-
|11
|41698001
|KEY-3/8" X 7/16"
|
|
|2
|-
|12
|N/A
|STOP-MAGNET SWING
|
|''† Discontinued''
|1
|-
|13
|PT0430
|FLANGE BEARING-4 BOLT-1 1/2"
|
|
|2
|-
|14
|HW0513
|BOLT-HHCS-1/2-13 X 2 1/4"
|
|
|8
|-
|15
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|16
|-
|16
|HW0110
|WASHER-LOCK-1/2"
|
|
|8
|-
|17
|HW0007
|NUT-HEX-1/2-13
|
|
|8
|-
|18
|41655002
|PLATE-MAGNET MOUNTING
|
|
|2
|-
|19
|41257015
|BLOCK-TIGHTENER
|
|''2-Piece Item''
|1
|-
|20
|41257016
|BLOCK-FIXED
|
|''2-Piece Item''
|1
|-
|21
|HW0423
|BOLT-SHCS-3/8-16 X 3 1/2"
|
|
|4
|-
|22
|HW0006
|NUT-NILN-3/8-16
|
|
|4
|-
|23
|HW0806
|SET SCREW-3/8-16 X 2"
|
|''Replaces Swivel Head''
|4
|-
|24
|HW0424
|NUT-JAM-3/8-16
|
|
|4
|-
|25
|41657017
|INSULATOR-MAGNET MOUNT
|
|
|2
|-
|26
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|8
|-
|27
|41657008
|PAD-MAGNET SLIDE
|
|
|2
|-
|28
|HW0314
|BOLT-FHSCS-1/4-20 X 1/2"
|
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Refer to [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Magnet_Pivot_Stop_(Rotary_Actuator) Magnet Pivot Stop (Rotary Actuator)] section for replacement/upgrade parts.''
|}

==== <big>''Magnet Pivot Stop (Rotary Actuator)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Magnet Pivot Stop (Rotary Actuator).png|alt=BE-SL & BE-DS Magnet Pivot Stop (Rotary Actuator)|frameless|551x551px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|80252012
|MAGNET SWING STOP KIT
|
|''Includes Items 1 through 6''
|A/R
|-
|1
|43057029
|PLATE-STOP
|
|
|1
|-
|2
|43058003
|SLEEVE-STOP
|
|
|2
|-
|3
|43057030
|SUPPORT-CABLE
|
|
|2
|-
|4
|PL0501
|GROMMET-1/2"
|
|
|2
|-
|5
|HW0509
|BOLT-HHCS-1/2-13 X 4 1/2"
|
|
|2
|-
|6
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|-
|7
|44557003
|PLATE-STOP
|
|''† Single compartment units only''
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† For units equipped with Pivot Shaft. See [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Current_Magnet_Arm_Configuration_(Rotary_Actuator) Current Magnet Arm Configuration (Rotary Actuator)] section for units with independent Magnet Pivot Bearings.''
|}

==== ''<big>[Current] Magnet Arm Configuration (Rotary Actuator — November 2014 to Present)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Current Magnet Arm Configuration (Rotary Actuator).png|alt=BE-SL & BE-DS Current Magnet Arm Configuration (Rotary Actuator)|frameless|547x547px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|N/A
|MAGNET PUSH/PULL ARM
|
|''†'' ''See notes''
|1
|-
|2
|43055010
|MAGNET MOUNT
|
|
|2
|-
|3
|PT0470
|BEARING-MAGNET PIVOT
|
|
|2
|-
|4
|HW0525
|BOLT-CARRIAGE-1/2-13 X 1 1/2"
|
|
|12
|-
|5
|HW0524
|BOLT-CARRIAGE-1/2-13 X 2"
|
|''††'' ''Stop Plate location''
|4
|-
|6
|HW0110
|WASHER-LOCK-1/2"
|
|
|16
|-
|7
|HW0007
|NUT-HEX-1/2-13
|
|
|16
|-
|8
|43058009
|PLATE-ROTATION STOP
|
|
|2
|-
|9
|43058003
|SLEEVE-STOP
|
|
|2
|-
|10
|43058010
|SUPPORT-CABLE
|
|
|2
|-
|11
|PL0501
|GROMMET-1/2"
|
|
|2
|-
|12
|HW0523
|BOLT-HHCS-1/2-13 X 4"
|
|
|2
|-
|13
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|-
|14
|43057037
|INSULATOR-BOTTOM
|
|
|2
|-
|15
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|8
|-
|16
|41657008
|SLIDE-MAGNET
|
|
|2
|-
|17
|HW0314
|BOLT-FHSCS-1/4-20 X 1/2"
|
|
|4
|-
|18
|44558001
|PLATE-ROTATION STOP
|
|''†† Single compartment units only''
|2
|-
|REF
|43052014
|ADJUSTABLE PUSH-PULL ARM
|
|''Includes Items 19 through 23''
|A/R
|-
|19
|43055018
|ARM BASE
|
|
|1
|-
|20
|43055019
|MAGNET MOUNT
|
|
|2
|-
|21
|HW0523
|BOLT-HHCS-1/2-13 X 4"
|
|
|2
|-
|22
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|4
|-
|23
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† 1-Piece Arm no longer available. Must be replaced with Adjustable Arm.''

''†† Single Compartment Stop Plates require (1) additional 2" Long Carriage Bolt each.''
|}

==== <big>''Magnet Mounting Hardware (Rotary Actuator)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Magnet Mounting Hardware (Rotary Actuator).png|alt=BE-SL & BE-DS Magnet Mounting Hardware (Rotary Actuator)|frameless|570x570px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43032009
|MAGNET ASSEMBLY
|
|''Includes Items 1 through 12''
|A/R
|-
|1
|N/A
|ELECTROMAGNET-95VDC
|
|
|2
|-
|2
|E0314
|SENSOR-PROXIMITY-30MM
|
|
|2
|-
|3
|N/A
|GASKET-REAR
|
|''Discontinued (Not Used)''
|2
|-
|4
|41657002
|COVER-PROXIMITY SENSOR HOUSING
|
|''Rear''
|2
|-
|5
|HW1065
|SCREW-SHCS-#6-32 X 3/8"
|
|
|8
|-
|6
|HW1066
|WASHER-LOCK-#6
|
|
|8
|-
|7
|E0376
|INDICATOR LIGHT
|
|''†'' ''See notes''
|2
|-
|8
|E0335
|RECEPTACLE-5 PIN MALE
|
|''With 12" lead''
|2
|-
|9
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|2
|-
|10
|N/A
|GASKET-FRONT
|
|''Discontinued (Not Used)''
|2
|-
|11
|41657003
|COVER-PROXIMITY SENSOR HOUSING
|80252015
|''Front''
|2
|-
|12
|HW0138
|SCREW-FHSCS-#8-32 X 3/8"
|80252015
|
|8
|-
|13
|HW0433
|STUD-1/2-13 X 5"
|80252006
| rowspan="5" |''For units with Magnet Pivot Shaft only.''

''See [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Discontinued_Magnet_Arm_Configuration_(Rotary_Actuator) Discontinued Magnet Arm Configuration (Rotary Actuator)] section''

''(Units built prior to 11/01/14)''
|8
|-
|14
|HW0007
|NUT-HEX-1/2-13
|80252006
|8
|-
|15
|HW0112
|WASHER-FLAT-1/2"-SAE
|80252006
|40
|-
|16
|HW1002
|SPRING-1/2"
|80252006
|24
|-
|17
|HW0008
|NUT-NILN-1/2-13
|80252006
|8
|-
|18
|HW0514
|BOLT-HHCS-1/2-13 X 2 1/2"
|80252014
| rowspan="4" |''For units with Independent Pivot Bearing only.''

''See [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Current_Magnet_Arm_Configuration_(Rotary_Actuator) Current Magnet Arm Configuration (Rotary Actuator)] section''

''(Units built 11/01/14 to Present)''
|4
|-
|19
|HW1002
|SPRING-1/2"
|80252014
|4
|-
|20
|HW0112
|WASHER-FLAT-1/2"-SAE
|80252014
|8
|-
|21
|HW0007
|NUT-HEX-1/2-13
|80252014
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Extractors built or Replacement Magnets shipped prior to October 2021 used Multi-piece Indicator Lights with Replaceable Bulb and Lens and are no longer available.''

''Current Indicator Light is a 1-Piece LED assembly. Replacement of any Multi-Piece Component requires replacing entire assembly with current, 1-Piece Indicator Light.''
|}

==== ''<big>Magnet Cords (Rotary Actuator)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Magnet Cords (Rotary Actuator).png|alt=BE-SL & BE-DS Magnet Cords (Rotary Actuator)|frameless|568x568px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E1105
|JUNCTION BOX-4" X 2" X 2"
|
|''Weather Proof Box''
|1
|-
|2
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
|3
|E1106
|COVER-JUNCTION BOX
|
|''Weather Proof with Gasket''
|1
|-
|4
|E0333
|RECEPTACLE-9 PIN MALE
|
|''With 12" Lead''
|1
|-
|5
|E0608-1
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .450" to .560"''
|2
|-
|6
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|3
|-
|7
|E0334
|CORD-5 PIN FEMALE
|
|''With 36" Lead''
|2
|-
|8
|E0332
|CORD-9 PIN FEMALE-90 DEG
|
|''With 36" Lead''
|1
|-
|9
|PL0501
|GROMMET-1/2"
|
|
|1
|-
|10
|41657013-2
|PLATE-PANEL MOUNTING
|
|''With Single Cable Hole''
|1
|-
|11
|E0334-6
|CORD-5 PIN FEMALE
|
|''With 72" Lead''
|2
|-
|12
|43057038-2
|PLATE-PANEL MOUNTING
|
|''With Dual Cable Holes''
|1
|}

==== ''<big>Panel Mounting (Rotary Actuator)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Panel Mounting (Rotary Actuator).png|alt=BE-SL & BE-DS Panel Mounting (Rotary Actuator)|frameless|550x550px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43057021
|PLATE-STIFFENER
|
|
|1
|-
|2
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|12
|-
|3
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|''(Not shown)''
|24
|-
|4
|HW0107
|WASHER-LOCK-3/8"
|
|
|12
|-
|5
|HW0005
|NUT-HEX-3/8-16
|
|
|12
|-
|6
|41637001
|PANEL-COMPONENT MOUNTING
|
|
|1
|-
|7
|HW0325
|BOLT-5/16-18 X 1 3/4"-PAN HEAD
|
|
|4
|-
|8
|N/A
|INSULATOR-THREADED FEMALE
|
|''Discontinued''
|4
|-
|9
|HW0106
|WASHER-FLAT-5/16"-SAE
|
|
|8
|-
|10
|HW0326
|NUT-NILN-5/16-18
|
|
|8
|-
|11
|E1016
|FUSE HOLDER
|
|
|1
|-
|12
|HW0130
|SCREW-RHMS-#8-32 X 1/2"
|
|
|1
|-
|13
|HW0133
|WASHER-FLAT-#8-SAE
|
|
|1
|-
|14
|HW0132
|NUT-NILN-#8-32
|
|
|1
|-
|15
|E0325
|FUSE-7AMP-250VAC
|
|''FLM-7 or FNM-7''
|1
|-
|16
|PL0307
|INSULATOR-MALE STUD
|
|
|4
|}

==== ''<big>Magnet Extractor Electrical Panel (Rotary Actuator)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Electrical Panel (Rotary Actuator).png|alt=BE-SL & BE-DS Electrical Panel (Rotary Actuator)|frameless|565x565px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41637001
|PANEL-COMPONENT MOUNTING
|
|
|1
|-
|2
|41637002
|WIRE WAY
|
|
|2
|-
|3
|41637003
|WIRE WAY
|
|
|1
|-
|4
|41637004
|TRACK-TERMINAL BLOCK MOUNTING
|
|
|1
|-
|5
|41637005
|TRACK-TERMINAL BLOCK MOUNTING
|
|
|1
|-
|6
|HW0130
|SCREW-RHMS-#8-32 X 1/2"
|
|
|10
|-
|7
|HW0133
|WASHER-FLAT-#8-SAE
|
|
|10
|-
|8
|HW0132
|NUT-NILN-#8-32
|
|''(Not shown)''
|16
|-
|9
|E1020
|TERMINAL BLOCK
|
|
|12
|-
|10
|E1040
|END BARRIER
|
|
|2
|-
|11
|E1330
|END ANCHOR
|
|
|4
|-
|12
|E1009
|RECTIFIER-FULL WAVE BRIDGE
|
|
|2
|-
|13
|HW0135
|SCREW-RHMS-#8-32 X 3/4"
|
|
|2
|-
|14
|E1313
|SOCKET-RELAY-8 PIN
|
|
|2
|-
|15
|HW0139
|SCREW-RHMS-#8-32 X 1 1/4"
|
|
|4
|-
|16
|E0331
|RELAY-DPDT-110VAC
|
|''With Indicator Light''
|2
|}

==== <big>''Swing Arm Stop (Rotary Actuator)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Magnet Mount Stop Swing Arm (Rotary Actuator).png|alt=BE-SL & BE-DS Magnet Mount Stop Swing Arm (Rotary Actuator)|frameless|562x562px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43055007
|MOUNT-STOP-SWING ARM
|
|
|2
|-
| rowspan="2" |2
|43057024
|STOP-SWING ARM
|
|''BE-24''
|4
|-
|43057023
|STOP-SWING ARM
|
|''BE-36 & BE-42''
|4
|-
|3
|HW0304
|BOLT-HHCS-1/4-20 X 1 1/2"
|
|
|4
|-
|4
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|8
|-
|5
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|6
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|7
|HW0403
|BOLT-HHCS-3/8-16 X 1 1/4"
|
|
|4
|-
|8
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|9
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|4
|}

=== <big>Extended Reach Hydraulics ''(Rotary Actuator)''</big> ===

==== <big>''Vacuum Extended Reach (Rotary Actuator)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Vacuum Extended Reach (Rotary Actuator).png|alt= BE-SL&DS Vacuum Extended Reach (Rotary Actuator)|frameless|531x531px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41257014
|TIE PLATE-SWING ARM
|
|''All units''
|1
|-
|<nowiki>-</nowiki>
|41655008
|EXTENSION-ARM
|
|''BE-36-2 only (Not shown)''
|1
|-
|<nowiki>-</nowiki>
|43455001
|EXTENSION-ARM
|
|''BE-42-2 only (Not shown)''
|1
|-
|2
|HW0504
|BOLT-HHCS-1/2-13 X 2"
|
|
|6
|-
|3
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|6
|-
|4
|HW0110
|WASHER-LOCK-1/2"
|
|
|6
|-
|5
|HW0007
|NUT-HEX-1/2-13
|
|
|6
|-
|6
|P0301-1
|HOSE-COIL-VACUUM
|
|
|1
|-
|7
|41257035
|STANDOFF
|
|
|2
|-
|8
|HW1072
|RESTRAINT-HOSE
|
|
|2
|-
|9
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|2
|-
|10
|HW0103
|WASHER-LOCK-1/4'
|
|
|2
|-
|11
|HW0318
|BOLT-SHCS-1/4-20 X 1 1/2"
|
|
|2
|-
|12
|HW0302
|BOLT-HHCS-1/4-20 X 3/4"
|
|
|1
|-
|13
|HW0312
|SCREW-SHSS-1/4-20 X 1"-CUP POINT
|
|
|1
|}
[[File:IOP-400 BE-SL&DS (10-23) Vacuum Extended Reach 2 (Rotary Actuator).png|alt= BE-SL&DS Vacuum Extended Reach (Rotary Actuator)|frameless|537x537px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41255005
|ARM-EXTENSION
|
|
|1
|-
|2
|HC0416
|CYLINDER-EXTENDED REACH
|
|
|1
|-
|3
|H1578
|ADAPTER-90 DEG-#6 JICM X #6 NPTM
|
|
|2
|-
|4
|41257031
|PIN-CLEVIS END
|
|
|1
|-
|5
|00197036
|PIN-ROD END
|
|
|1
|-
|6
|HW1058
|PIN-HITCH
|
|
|4
|}
[[File:IOP-400 BE-SL&DS (10-23) Vacuum Extended Reach 3 (Rotary Actuator).png|alt= BE-SL&DS Vacuum Extended Reach (Rotary Actuator)|frameless|537x537px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41255004
|HOUSING-EXTENDED REACH
|
|
|1
|-
|2
|41257030
|PLATE-END
|
|
|1
|-
|3
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|4
|-
|4
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|8
|-
|5
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|6
|HW0005
|NUT-HEX-3/8-16
|
|
|4
|-
|7
|41258002
|PLATE-BEARING
|
|''Side''
|2
|-
|8
|41258005
|PLATE-SHIM
|
|''Side''
|2
|-
|9
|41258003
|PLATE-BEARING
|
|''Upper/ Lower''
|2
|-
|10
|41258004
|PLATE-SHIM
|
|''Upper/ Lower''
|2
|-
|11
|HW0812
|SCREW-SHSS-1/4-20 X 5/8"-HALF DOG
|
|
|28
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|28
|}

==== <big>''Extended Reach Rotary Actuator''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Extended Reach (Rotary Actuator).png|alt=BE-SL & DS Extended Reach (Rotary Actuator)|frameless|538x538px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43046001
|ROTARY ACTUATOR
|
|
|1
|-
|2
|80000002
|ROTARY ACTUATOR BASE ASSEMBLY
|
|''Without Actuator''
|1
|-
|2A
|N/A
|VERTICAL CARRIER PLATE-OUTER
|
|''Included with 80000002''
|2
|-
|2B
|N/A
|VERTICAL CARRIER PLATE-INNER
|
|''Included with 80000002''
|1
|-
|2C
|N/A
|CARRIER BASE PLATE
|
|''Included with 80000002''
|1
|-
|3
|HW1070
|PIN-PULL DOWEL-5/8" X 1 1/2"
|
|
|2
|-
|4
|HW0508
|BOLT-SHCS-1/2-13 X 3/4"
|
|
|3
|-
|5
|HW1045
|PIN-PULL DOWEL-3/8" X 1 1/2"
|
|''Included with 80000002''
|6
|-
|6
|HW0412
|BOLT-SHCS-3/8-16 X 1 1/4"
|
|''Included with 80000002''
|12
|-
|7
|H0010
|FITTING-BULKHEAD-3/4-16 X #4 FNPT
|
|
|4
|-
|8
|H1579
|ADAPTER-90 DEG-#6 JICM X #4 NPTM
|
|
|4
|}
[[File:IOP-400 BE-SL&DS (10-23) Extended Reach 2 (Rotary Actuator).png|alt=BE-SL & DS Extended Reach |frameless|538x538px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|PT0634
|BRACKET-MALE END
|
|''Sold as set''
|1
|-
|2
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|4
|-
|3
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|10
|-
|4
|HW0103
|WASHER-LOCK-1/4"
|
|
|6
|-
|5
|HW0002
|NUT-HEX-1/4-20
|
|
|6
|-
|6
|PT0627
|HOSE CARRIER
|
|''14 Links required''
|39"
|-
|7
|PT0634
|BRACKET-FEMALE END
|
|''Sold as set''
|1
|-
|8
|HC0261
|VALVE-CROSS PORT RELIEF
|
|
|1
|-
|8a
|43046003
|REPLACEMENT CARTRIDGE
|
|''† For Item 8 (Not shown)''
|2
|-
|9
|HW0308
|BOLT-HHCS-1/4-20 X 2 1/2"
|
|
|2
|-
|10
|H1546
|ADAPTER-#6 JICM X #8 SAEM
|
|
|2
|-
|11
|H1617
|ADAPTER-45 DEG-#6 JICM X #8 SAEM
|
|
|2
|-
|12
|HC0237
|VALVE-SEQUENCING
|
|
|1
|-
|12a
|43046005
|REPLACEMENT CARTRIDGE
|
|''† For Item 12 (Not shown)''
|A/R
|-
|13
|HW0317
|BOLT-HHCS-1/4-20 X 3 1/2"
|
|
|2
|-
|14
|H1560
|ADAPTER-45 DEG-#8 JICM X #8 SAEM
|
|
|4
|-
|15
|H1600
|ADAPTER-90 DEG-#6 JICM X #8 SAEM
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Cartridges are for replacement only''
|}

==== <big>''Magnet Extended Reach (Rotary Actuator)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Magnet Extended Reach (Rotary Actuator).png|alt=BE-SL&DS Magnet Extended Reach (Rotary Actuator)|frameless|549x549px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43055011
|ARM-EXTENSION-MAGNET
|
|
|1
|-
|2
|HC0415
|CYLINDER-EXTENDED REACH-MAGNET
|
|''2 1/2" X 8" Cylinder''
|1
|-
|3
|H1578
|ADAPTER-90 DEG-#6 JICM X #6 MNPT
|
|
|2
|-
|4
|43057042
|PIN-CLEVIS END
|
|
|1
|-
|5
|43057043
|PIN-ROD END
|
|
|1
|-
|6
|HW1132
|RETAINING RING-EXTERNAL-3/4"I.D.
|
|
|4
|-
|7
|HW1043
|CLAMP-CYLINDER
|
|
|2
|-
|8
|43057044-2
|SUPPORT-CABLE
|
|
|2
|-
|9
|PL0501
|GROMMET-1/2" I.D.
|
|
|4
|-
|10
|43058019
|SUPPORT-CABLE-BAND CLAMP
|
|
|2
|-
|11
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|12
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|}
[[File:IOP-400 BE-SL&DS (10-23) Magnet Extended Reach Bearing and Shim (Rotary Actuator).png|alt=BE-SL&DS Magnet Extended Reach Bearing and Shim (Rotary Actuator)|frameless|556x556px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43055012
|HOUSING-EXTENDED REACH-MAGNET
|
|
|1
|-
|2
|50057008
|PLATE-END
|
|
|1
|-
|3
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|4
|-
|4
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|8
|-
|5
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|6
|HW0005
|NUT-HEX-3/8-16
|
|
|4
|-
|7
|43058013
|PLATE-BEARING-SIDE
|
|
|2
|-
|8
|43058016
|PLATE-SHIM-SIDE
|
|
|2
|-
|9
|43058014
|PLATE-BEARING-UPPER/LOWER
|
|
|2
|-
|10
|43058015
|PLATE-SHIM-UPPER/LOWER
|
|
|2
|-
|11
|HW0812
|SCREW-SHSS-1/4-20 X 5/8"-HALF DOG
|
|
|24
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|24
|}

==== <big>''Extended Reach End Plates''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Magnet Extended Reach End Plates (Rotary Actuator).png|alt=BE-SL&DS Magnet Extended Reach End Plates (Rotary Actuator)|frameless|574x574px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|N/A
|CARRIER SHAFT-EXTRACTOR ARM
|
|''† 3-Hole version''
|A/R
|-
|2
|PT0413
|COLLAR-SHAFT-3"
|
|
|4
|-
|3
|50057009
|PLATE-END-3 HOLE
|
|''Replacement part only''
|4
|-
|4
|50057010
|SHIM-END PLATE
|
|''†† See notes''
|A/R
|-
|5
|HW1076
|BOLT-FHSCS-3/8-16 X 1"
|
|
|12
|-
|6
|43057045
|CARRIER SHAFT-EXTRACTOR ARM
|
|''1-Hole version''
|2
|-
|7
|43017076
|PLATE-END-1 HOLE
|
|
|4
|-
|8
|HW0603
|BOLT-FHSCS-5/8-11 X 2"
|
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† 3-Hole Carrier Shaft no longer available. Must replace 3-Hole Shaft with current, 1-Hole version along with new End Plates and hardware.''
|-
| colspan="6" |''†† Shim quantity varies due to manufacturing tolerences.''
|}

=== <big>Carrier Shafts & Bearings ''(Helical Actuator)''</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Carrier Shaft BearingsEnd Plates (Helical Actuator).png|alt=BE-SL & BE-DS Carrier Shaft Bearings (Helical Actuator)|frameless|567x567px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43057045
|CARRIER SHAFT-EXTRACTOR ARM
|
|''† See notes''
|2
|-
|2
|43054007
|BEARING-EXTRACTOR ARM CARRIER
|80252002
|
|4
|-
|3
|HW0412
|BOLT-SHCS-3/8-16 X 1 1/4"
|80252002
|
|16
|-
|4
|PT0413
|COLLAR-SHAFT-3"
|
|
|4
|-
|5
|50057010
|SHIM-END PLATE
|
|
|A/R
|-
|6
|43017076
|PLATE-END-1 HOLE
|
|
|4
|-
|7
|HW0603
|BOLT-FHSCS-5/8-11 X 2"
|
|
|4
|-
|8
|PT0624
|FITTING-ZERK
|80252002
|''(Not shown)''
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† See [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Extended_Reach_End_Plates Extended Reach End Plates] section for Extended Reach equipped units.''
|}

=== <big>Drive Screw Components ''(Helical Actuator)''</big> ===

==== <big>''Drive Nut Assembly (Helical Actuator)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Drive Nut Assembly (Helical Actuator).png|alt=BE-SL&DS Drive Nut Assembly (Helical Actuator)|frameless|601x601px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43054006
|DRIVE NUT ASSEMBLY
|80252003
|
|1
|-
|2
|HW0426
|BOLT-SHCS-3/8-16 X 5 1/2"
|80252003
|''†'' ''See notes''
|4
|-
|3
|HW0108
|WASHER-FLAT-3/8"-SAE
|80252003
|''†'' ''See notes''
|4
|-
|4
|HW0006
|NUT-NILN-3/8-16
|80252003
|''†'' ''See notes''
|4
|-
|5
|PT0624
|FITTING-ZERK
|80252003
|
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† It is recommended to replace Mounting Hardware when replacing Drive Nut Assembly.''
|}

=== <big>Swing Arms & Actuator ''(Helical Actuator)''</big> ===

==== ''<big>[Discontinued] Helical Actuator (Prior to July 2023)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Helical Actuator.png|alt= BE-SL&DS Discontinued Helical Actuator used prior to July 2023|frameless|551x551px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|N/A
|HELICAL ACTUATOR
|
|''†'' ''See notes''
|1
|-
|2
|43057046
|ACTUATOR BASE PLATE
|
|
|1
|-
|3
|43058022
|SPACER-ACTUATOR
|
|
|4
|-
|4
|HW0725
|BOLT-HHCS-3/4-16 X 4-3/4"-GR8
|
|
|4
|-
|5
|HW0066
|NUT-JAM-3/4-16-GR8
|
|
|4
|-
|6
|43055013
|SWING ARM-LHS
|
| rowspan="6" |''††'' ''See notes''
|1
|-
|7
|HW0620
|BOLT-HHCS-5/8-11 X 1-1/4"
|
|6
|-
|8
|HW0013
|WASHER-LOCK-5/8"
|
|6
|-
|9
|43055014
|SWING ARM-RHS
|
|1
|-
|10
|HW0502
|BOLT-HHCS-1/2-13 X 1-1/4"
|
|6
|-
|11
|HW0110
|WASHER-LOCK-1/2"
|
|6
|-
|12
|43042008
|3/8" TUBE X #6 JIC HARD-PIPE
|
|
|1
|-
|13
|43042010
|3/8" TUBE X #6 JIC HARD-PIPE, LONG
|
|
|1
|-
|14
|H1619
|ADAPTER-90 DEG-#6 JICM X #4 SAEM
|
|
|2
|-
|15
|H0010
|FITTING-H-BULKHEAD-1/4" FNPT
|
|
|2
|-
|16
|H1504
|ADAPTER-#6 JICM X #4 NPTM
|
|
|2
|-
|17
|HW1082
|CLAMP-HOSE
|
|
|1
|-
|18
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Discontinued Helical Actuator no longer available. Must replace with current Helical Actuator Retro Kit 80252032. See [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Current_Helical_Actuator Current Helical Actuator] section.''

''†† Swing Arms manufactured prior to January 2022 use 10 Bolts & Washer per Swing Arm.''
|}

==== ''<big>[Current] Helical Actuator (July 2023 to Present)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Current Helical Actuator.png|alt= BE-SL&DS Current Helical Actuator used July 2023 to Present|frameless|571x571px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|N/A
|43052020
|HELICAL ACTUATOR ASSEMBLY
|
|''Includes Items 1 through 17''
|1
|-
|1
|HC0180
|HELICAL ACTUATOR
|80252032
|
|1
|-
|2
|43057046
|ACTUATOR BASE PLATE
|
|
|1
|-
|3
|43058022
|SPACER-ACTUATOR
|
|
|4
|-
|4
|HW0725
|BOLT-HHCS-3/4-16 X 4-3/4"-GR8
|
|
|4
|-
|5
|HW0066
|NUT-JAM-3/4-16-GR8
|
|
|4
|-
|6
|43055013
|SWING ARM-LHS
|
|
|1
|-
|7
|HW0620
|BOLT-HHCS-5/8-11 X 1-1/4"
|
|
|6
|-
|8
|HW0113
|WASHER-LOCK-5/8"
|
|
|6
|-
|9
|43055014
|SWING ARM-RHS
|
|
|1
|-
|10
|HW0502
|BOLT-HHCS-1/2-13 X 1-1/4"
|
|
|6
|-
|11
|HW0110
|WASHER-LOCK-1/2"
|
|
|6
|-
|12
|43042011
|3/8" TUBE X #6 JIC HARD-PIPE, 90 DEG
|80252032
|''†'' ''See notes''
|1
|-
|13
|43042012
|3/8" TUBE X #6 JIC HARD-PIPE, SHORT
|80252032
|''†'' ''See notes''
|1
|-
|14
|H1619
|ADAPTER-90 DEG-#6 JICM X #4 SAEM
|80252032
|
|2
|-
|15
|H0010
|FITTING-H-BULKHEAD-1/4" FNPT
|
|
|2
|-
|16
|H1504
|ADAPTER-#6 JICM X #4 NPTM
|80252032
|
|1
|-
|17
|H1691
|ADAPTER-45 DEG-#6 JICM X #4 NPTM
|80252032
|''†'' ''See notes''
|1
|-
|18
|HW1082
|CLAMP-HOSE
|
|
|1
|-
|19
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Hard-Pipes and 45-Degree Adapter required if replacing discontinued Actuator with current Actuator. Kit PT# 80252032 required for discontinued Actuator replacement.''
|}

=== <big>Swing Arm Stops & Tie Plate ''(Helical Actuator)''</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Swing Arm Stops and Tie Plate (Helical Actuator).png|alt=BE-SL&DS Swing Arm Stops and Tie Plate (Helical Actuator)|frameless|549x549px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43057050
|TIE PLATE-HELICAL SWING ARM
|
|
|1
|-
|2
|HW0603
|BOLT-FHSCS-5/8-11 X 2"
|
|
|4
|-
|3
|HW0113
|WASHER-LOCK-5/8"
|
|
|4
|-
|4
|HW0010
|NUT-JAM-5/8-11
|
|
|4
|-
|5
|43057052
|STOP-POLY-SWING ARM
|
|''†'' ''See notes''
|4
|-
|6
|HW0441
|BOLT-FHSCS-3/8-16 X 1-1/2"
|
|
|4
|-
|7
|HW0031
|NUT-LOCK-3/8-16, DEFORMED THREAD
|
|''††'' ''See notes''
|4
|-
|8
|44555002
|SWING ARM STOP
|
|''Single compartment units only''
|A/R
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Replacement Poly Stop design updated from square to round. Stop Spacers not required with current, round-style Stops.''
|-
| colspan="6" |''†† Deformed Thread Lock Nut replaces Acorn Nut and Split Lock Washer used previously.''
|}

=== <big>'''Push/Pull Arm Mounting ''(Helical Actuator)'''''</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Push Pull Arm Mounting (Helical Actuator).png|alt=BE-SL & BE-DS Push Pull Arm Mounting (Helical Actuator)|frameless|581x581px]]
{| class="wikitable"
! rowspan="2" |ITEM
! rowspan="2" |BHS PART NUMBER
! rowspan="2" |DESCRIPTION
! rowspan="2" |REF. KIT NO.
! rowspan="2" |NOTES
! colspan="3" |NO. REQ
|-
!BE-24
!BE-36
!BE-42
|-
| rowspan="2" |1
|41655008
|EXTENSION-ARM
|
|''† BE-36 units only''
|<nowiki>-</nowiki>
|1
|<nowiki>-</nowiki>
|-
|43455001
|EXTENSION-ARM
|
|''† BE-42 units only''
|<nowiki>-</nowiki>
|<nowiki>-</nowiki>
|1
|-
|2
|HW0504
|BOLT-HHCS-1/2-13 X 2"
|
|
|6
| colspan="2" |12
|-
|3
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|12
| colspan="2" |24
|-
|4
|HW0110
|WASHER-LOCK-1/2"
|
|
|6
| colspan="2" |12
|-
|5
|HW0007
|NUT-HEX-1/2-13
|
|
|6
| colspan="2" |12
|-
! colspan="8" |NOTES
|-
| colspan="8" |''† BE-24 units do not utilize an arm extension.''
|}

=== <big>Vacuum Extractor Arm ''(Helical Actuator)''</big> ===

==== ''<big>Non-Pivoting Vacuum Cup Arm (Helical Actuator)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Non-Pivoting Vaccum Cup Arm (Helical Actuator).png|alt=BE-SL & BE-DS Non-Pivoting Vacuum Cup Arm (Helical Actuator)|frameless|567x567px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HW0428
|STUD-VACUUM-3/8-16 X 5"
|HW-KIT-2
|
|8
|-
|2
|HW0108
|WASHER-FLAT-3/8"-SAE
|HW-KIT-2
|
|40
|-
|3
|HW1001
|SPRING-3/8"
|HW-KIT-2
|
|24
|-
|4
|HW0424
|NUT-JAM-3/8-16
|HW-KIT-2
|
|8
|-
|5
|HW0006
|NUT-NILN-3/8-16
|HW-KIT-2
|
|8
|-
|6
|P0402
|HOSE BARB-1/4" X #4 MNPT-BRASS
|
|
|2
|-
|REF
|43052014
|ADJUSTABLE PUSH-PULL ARM
|
|''Includes Items 7 through 11''
|A/R
|-
|7
|43055018
|ARM BASE
|
|
|1
|-
|8
|43055019
|VACUUM CUP MOUNT
|
|
|2
|-
|9
|HW0523
|BOLT-HHCS-1/2-13 X 4"
|
|
|2
|-
|10
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|4
|-
|11
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|}

==== ''<big>Pivoting Vacuum Cup Arm (Helical Actuator)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Pivoting Vacuum Cup Arm (Helical Actuator).png|alt=BE-SL & BE-DS Pivoting Vacuum Extractor Cup Arm (Helical Actuator)|frameless|551x551px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43052014
|ADJUSTABLE PUSH-PULL ARM
|
|''Includes Items 1 through 5''
|A/R
|-
|1
|43055018
|ARM BASE
|
|
|1
|-
|2
|43055019
|VACUUM CUP MOUNT
|
|
|2
|-
|3
|HW0523
|BOLT-HHCS-1/2-13 X 4"
|
|
|2
|-
|4
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|4
|-
|5
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|-
|6
|43055020
|MOUNT-PIVOT-VACUUM CUP
|
|
|2
|-
|7
|PT0470
|BEARING-PIVOT
|
|
|2
|-
|8
|HW0525
|BOLT-CARRIAGE-1/2-13 X 1 1/2"
|
|
|12
|-
|9
|HW0524
|BOLT-CARRIAGE-1/2-13 X 2"
|
|
|4
|-
|10
|HW0110
|WASHER-LOCK-1/2"
|
|
|16
|-
|11
|HW0008
|NUT-HEX-1/2-13
|
|
|16
|-
|12
|43058009
|PLATE-ROTATION STOP
|
|
|2
|-
|13
|43058003
|SLEEVE-STOP
|
|
|2
|-
|14
|43058010
|SUPPORT-CABLE
|
|
|2
|-
|15
|E0622
|RESTRAINT-1/2"
|
|''Grip size .450" to .560"''
|4
|-
|16
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|4
|-
|17
|HW0523
|BOLT-HHCS-1/2-13 X 4"
|
|
|2
|-
|18
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|-
|19
|43037002-2
|SUPPORT-CABLE RESTRAINT
|
|
|2
|-
|20
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|4
|-
|21
|P0506
|ELBOW-STR-90 DEG-#4 NPT-BRASS
|
|
|2
|-
|22
|P0402
|HOSE BARB-1/4" X #4 MNPT-BRASS
|
|
|2
|-
|23
|43057056-2
|BRACKET-HOSE SUPPORT
|
|
|2
|-
|24
|PL0507
|GROMMET-5/8" I.D.
|
|
|2
|-
|25
|P0302
|HOSE-VACUUM-1/4" I.D.
|
|''2 Pieces at 48" each''
|96"
|-
|26
|HW0443
|BOLT-HHCS-3/8-16 X 3-1/2"
|HW-KIT-3
|
|8
|-
|27
|HW1001
|SPRING-3/8"
|HW-KIT-3
|
|16
|-
|28
|HW0108
|WASHER-FLAT-3/8"-SAE
|HW-KIT-3
|
|32
|-
|29
|HW0424
|NUT-JAM-3/8-16
|HW-KIT-3
|
|4
|}

==== ''<big>Single Compartment Vacuum Cup Rotation Stop</big>'' ''<big>(Helical Actuator)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Single Compartment Rotation Stop (Helical Actuator).png|alt=BE-SL & BE-DS Vacuum Cup Rotation Stop (Helical Actuator)|frameless|568x568px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|445558001
|PLATE-ROTATION STOP
|
|''Single compartment units only''
|2
|-
|2
|HW0525
|BOLT-CARRIAGE-1/2-13 X 1 1/2"
|
|
|2
|-
|3
|HW0524
|BOLT-CARRIAGE-1/2-13 X 2"
|
|
|6
|-
|4
|HW0110
|WASHER-LOCK-1/2"
|
|
|8
|-
|5
|HW0008
|NUT-HEX-1/2-13
|
|
|8
|}

==== <big>''Vacuum Components (Helical Actuator)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Vacuum Pump Components (Helical Actuator).png|alt=BE-SL & BE-DS Vacuum Pump Components (Helical Actuator)|frameless|537x537px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43058021
|STIFFENER PLATE-HELICAL SWING ARM
|
|
|2
|-
|2
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|12
|-
|3
|HW0108
|WASHER-FLAT-3/8"
|
|
|24
|-
|4
|HW0107
|WASHER-LOCK-3/8"
|
|
|12
|-
|5
|HW0005
|NUT-HEX-3/8-16
|
|
|12
|-
|6
|P0005
|PUMP-VACUUM
|
|
|1
|-
|7
|P0207
|VALVE-VACUUM RELEASE
|
|
|2
|-
|8
|P0208
|FILTER-HI FLOW
|
|
|3
|-
|9
|H0011
|NIPPLE-#4 X 2"-BRASS
|
|
|1
|-
|10
|P0502
|TEE-#4 FNPT-BRASS
|
|
|1
|-
|11
|P0506
|ELBOW-STR-90 DEG-#4 NPT-BRASS
|
|
|4
|-
|12
|P0503
|NIPPLE-#4 NPT-BRASS
|
|
|2
|-
|13
|P0402
|HOSE BARB-1/4" X #4 MNPT-BRASS
|
|
|6
|-
|14
|P0111
|FILTER-VACUUM-IN-LINE
|
|
|2
|-
|15
|HW0206
|SCREW-RHMS-#10-32 X 3/4"
|
|
|4
|-
|16
|43037014-2
|BRACKET-CABLE RESTRAINT
|
|
|1
|-
|17
|E0622
|RESTRAINT-1/2"
|
|''Grip size .450" to .560"''
|2
|-
|18
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|2
|-
|19
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
|20
|E0611
|JUNCTION BOX-4" X 2" X 2"
|
|
|1
|-
|21
|E0612
|COVER-JUNCTION BOX
|
|
|1
|-
|22
|E0624
|CONNECTOR-1/2"
|
|''Includes Lock Nut''
|1
|-
|23
|HW0212
|SCREW-RHMS-#10-24 X 1/2"
|
|
|2
|}

=== <big>Magnet Extractor Arm ''(Helical Actuator)''</big> ===

==== <big>''Magnet Arm (Helical Actuator)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Magnet Arm (Helical Actuator).png|alt=BE-SL & BE-DS Magnet Arm (Helical Actuator)|frameless|555x555px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43052014
|ADJUSTABLE PUSH-PULL ARM
|
|''Includes Items 1 through 5''
|A/R
|-
|1
|43055018
|ARM BASE
|
|
|1
|-
|2
|43055019
|VACUUM CUP MOUNT
|
|
|2
|-
|3
|HW0523
|BOLT-HHCS-1/2-13 X 4"
|
|
|2
|-
|4
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|4
|-
|5
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|-
|6
|43055016
|MOUNT-PIVOT-MAGNET
|
|
|2
|-
|7
|PT0470
|BEARING-PIVOT
|
|
|2
|-
|8
|HW0525
|BOLT-CARRIAGE-1/2-13 X 1 1/2"
|
|
|12
|-
|9
|HW0524
|BOLT-CARRIAGE-1/2-13 X 2"
|
|
|4
|-
|10
|HW0110
|WASHER-LOCK-1/2"
|
|
|16
|-
|11
|HW0008
|NUT-HEX-1/2-13
|
|
|16
|-
|12
|43058009
|PLATE-ROTATION STOP
|
|
|2
|-
|13
|43058003
|SLEEVE-STOP
|
|
|2
|-
|14
|43058010
|SUPPORT-CABLE
|
|
|2
|-
|15
|HW0523
|BOLT-HHCS-1/2-13 X 4"
|
|
|2
|-
|16
|HW0008
|NUT-NILN-1/2-13
|
|
|2
|-
|17
|E0622
|RESTRAINT-1/2"
|
|''Grip Size .450" to .560"''
|2
|-
|18
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|2
|-
|19
|43037002-2
|SUPPORT-CABLE RESTRAINT
|
|
|2
|-
|20
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|4
|-
|21
|E0334-6'
|CORD-5 PIN FEMALE
|
|''With 72" Lead''
|2
|-
|22
|E1041
|WIRE LOOM-SPIRAL-3/8"
|
|''2 Pieces at 24" each''
|48"
|-
|23
|PL0501
|GROMMET-1/2" I.D.
|
|
|2
|-
|24
|43057037
|INSULATOR-BOTTOM
|
|
|2
|-
|25
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|8
|-
|26
|41657008
|SLIDE-MAGNET
|
|
|2
|-
|27
|HW0314
|BOLT-FHSCS-1/4-20 X 1/2"
|
|
|4
|}

==== <big>''Magnet Assembly (Helical Actuator)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Magnet Assembly (Helical Actuator).png|alt=BE-SL & BE-DS Magnet Assembly (Helical Actuator)|frameless|550x550px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43032009
|MAGNET ASSEMBLY
|
|''Includes items 1 through 12''
|A/R
|-
|1
|N/A
|ELECTROMAGNET-95VDC
|
|
|2
|-
|2
|E0314
|SENSOR-PROXIMITY-30MM
|
|
|2
|-
|3
|41657002
|COVER-PROXIMITY SENSOR HOUSING
|
|''Rear''
|2
|-
|4
|HW1065
|SCREW-SHCS-#6-32 X 3/8"
|
|
|8
|-
|5
|HW1066
|WASHER-LOCK-#6
|
|
|8
|-
|6
|E0335
|RECEPTACLE-5 PIN MALE
|
|''With 12" Lead''
|2
|-
|7
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|2
|-
|8
|E0376
|INDICATOR LIGHT
|
|''† See notes''
|2
|-
|9
|41657003
|COVER-PROXIMITY SENSOR HOUSING
|80252015
|''Front''
|2
|-
|10
|HW0138
|SCREW-FHSCS-#8-32 X 3/8"
|80252015
|
|8
|-
|11
|HW0514
|BOLT-HHCS-1/2-13 X 2 1/2"
|80252014
|
|4
|-
|12
|HW1002
|SPRING-1/2"
|80252014
|
|4
|-
|13
|HW0112
|WASHER-FLAT-1/2"-SAE
|80252014
|
|8
|-
|14
|HW0007
|NUT-HEX-1/2-13
|80252014
|
|4
|-
|15
|E0336
|METAL OXIDE VARISTOR
|
|''Not shown''
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Extractors built or Replacement Magnets shipped prior to October 2021 used Multi-piece Indicator Lights with Replaceable Bulb and Lens and are no longer available.''

''Current Indicator Light is a 1-Piece LED assembly. Replacement of any Multi-Piece Component requires replacing entire assembly with current, 1-Piece Indicator Light''
|}

==== <big>''Magnet Components (Helical Actuator)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Magnet Components (Helical Actuator).png|alt=BE-SL & BE-DS Magnet Components (Helical Actuator)|frameless|545x545px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43058021
|STIFFENER PLATE-HELICAL SWING ARM
|
|
|1
|-
|2
|43057051-2
|STIFFENER-MAGNET-HELICAL SWING ARM
|
|
|1
|-
|3
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|12
|-
|4
|HW0108
|WASHER-FLAT-3/8"
|
|
|24
|-
|5
|HW0107
|WASHER-LOCK-3/8"
|
|
|12
|-
|6
|HW0005
|NUT-HEX-3/8-16
|
|
|12
|-
|7
|PL0307
|INSULATOR-MALE STUD
|
|
|4
|-
|8
|HW0106
|WASHER-FLAT-5/16"-SAE
|
|
|8
|-
|9
|HW0105
|WASHER-LOCK-5/16"
|
|
|8
|-
|10
|HW0004
|NUT-HEX-5/16-18
|
|
|8
|-
|11
|E0622
|RESTRAINT-1/2"
|
|''Grip Size .450" to .560"''
|1
|-
|12
|E0608-1
|RESTRAINT-1/2"-90 DEG
|
|''Grip Size .450" to .560"''
|2
|-
|13
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|3
|-
|14
|E1016
|FUSE HOLDER
|
|
|1
|-
|15
|E0325
|FUSE-7 AMP-250VAC
|
|''FLM-7 or FNM-7''
|1
|-
|16
|HW0130
|SCREW-RHMS-#8-32 X 1/2"
|
|
|1
|-
|17
|HW0133
|WASHER-FLAT-#8-SAE
|
|
|1
|-
|18
|HW0132
|NUT-NILN-#8-32
|
|
|1
|}

==== <big>''Magnet Electrical Panel (Helical Actuator)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Magnet Electrical Panel (Helical Actuator).png|alt=BE-SL & BE-DS Magnet Electrical Panel (Helical Actuator)|frameless|536x536px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41637001
|PANEL-COMPONENT MOUNTING
|
|
|1
|-
|2
|41637002
|WIRE WAY-SHORT
|
|
|2
|-
|3
|41637003
|WIRE WAY-LONG
|
|
|1
|-
|4
|41637004
|TRACK-MOUNTING-SHORT
|
|
|1
|-
|5
|41637005
|TRACK-MOUNTING-LONG
|
|
|1
|-
|6
|HW0130
|SCREW-RHMS-#8-32 X 1/2"
|
| rowspan="3" |''Mounting Track Hardware not shown''
|10
|-
|7
|HW0132
|WASHER-FLAT-#8-SAE
|
|10
|-
|8
|HW0133
|NUT-NILN-#8-32
|
|16
|-
|9
|E1020
|TERMINAL BLOCK
|
|
|12
|-
|10
|E1040
|END BARRIER
|
|
|2
|-
|11
|E1330
|END ANCHOR
|
|
|4
|-
|12
|E1009
|RECTIFIER-FULL WAVE BRIDGE
|
|
|2
|-
|13
|HW0135
|SCREW-RHMS-#8-32 X 3/4"
|
|
|2
|-
|14
|E1313
|SOCKET-RELAY-8 PIN
|
|
|2
|-
|15
|E0331
|RELAY-DPDT-110VAC
|
|''With Indicator Light''
|2
|-
|16
|HW0139
|SCREW-RHMS-#8-32 X 1 1/4"
|
|
|4
|}

=== <big>Extended Reach Hydraulics ''(Helical Actuator)''</big> ===

==== ''<big>[Discontinued] Helical Actuator (Prior to July 2023)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Extended Reach Discontinued Helical Actuator.png|alt=BE-SL & BE-DS Discontinued Helical Actuator|frameless|589x589px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43042009
|3/8" TUBE X #6 JIC HARD-PIPE
|
|
|2
|-
|2
|H1579
|ADAPTER-90 DEG-#6 JICM X #4 MNPT
|
|
|2
|-
|3
|H0010
|FITTING-BULKHEAD-3/4-16 X #4 FNPT
|
|
|2
|-
|4
|43055017
|ELBOW-BULKHEAD
|
|
|2
|-
|5
|HW0302
|BOLT-HHCS-1/4-20 X 3/4"
|
|
|4
|-
|6
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
| rowspan="3" |7
|4-48-0402-0402
|HYD HOSE-1/4" X 48" (BE-24 UNITS)
|
| rowspan="3" |''Cylinder Rod-End Hose''
| rowspan="3" |1
|-
|4-54-0402-0402
|HYD HOSE-1/4" X 54" (BE-36 UNITS)
|
|-
|4-56-0402-0402
|HYD HOSE-1/4" X 56" (BE-42 UNITS)
|
|-
| rowspan="3" |8
|4-38-0402-0402
|HYD HOSE-1/4" X 38" (BE-24 UNITS)
|
| rowspan="3" |''Cylinder Base-End Hose''
| rowspan="3" |1
|-
|4-44-0402-0402
|HYD HOSE-1/4" X 44" (BE-36 UNITS)
|
|-
|4-46-0402-0402
|HYD HOSE-1/4" X 46" (BE-42 UNITS)
|
|-
|9
|41257035
|STANDOFF-HOSE
|
|
|2
|-
|10
|HW1093
|CLAMP-CABLE-3/4"
|
|
|2
|-
|11
|HW0311
|BOLT-FHSCS-1/4-20 X 3/4"
|
|
|2
|-
|12
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|}

==== ''<big>[Current] Helical Actuator (July 2023 to Present)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Extended Reach Current Helical Actuator.png|alt=BE-SL & BE-DS Current Extended Reach Helical Actuator|frameless|572x572px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43042013
|3/8" TUBE X #6 JIC HARD-PIPE
|
|
|2
|-
|2
|H1579
|ADAPTER-90 DEG-#6 JICM X #4 MNPT
|
|
|2
|-
|3
|H0010
|FITTING-BULKHEAD-3/4-16 X #4 FNPT
|
|
|2
|-
|4
|43055021
|ELBOW-BULKHEAD
|
|
|2
|-
|5
|HW0302
|BOLT-HHCS-1/4-20 X 3/4"
|
|
|4
|-
|6
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
| rowspan="3" |7
|4-48-0402-0402
|HYD HOSE-1/4" X 48" (BE-24 UNITS)
|
| rowspan="3" |''Cylinder Rod-End Hose''
| rowspan="3" |1
|-
|4-54-0402-0402
|HYD HOSE-1/4" X 54" (BE-36 UNITS)
|
|-
|4-56-0402-0402
|HYD HOSE-1/4" X 56" (BE-42 UNITS)
|
|-
| rowspan="3" |8
|4-38-0402-0402
|HYD HOSE-1/4" X 38" (BE-24 UNITS)
|
| rowspan="3" |''Cylinder Base-End Hose''
| rowspan="3" |1
|-
|4-44-0402-0402
|HYD HOSE-1/4" X 44" (BE-36 UNITS)
|
|-
|4-46-0402-0402
|HYD HOSE-1/4" X 46" (BE-42 UNITS)
|
|-
|9
|41257035
|STANDOFF-HOSE
|
|
|2
|-
|10
|HW1093
|CLAMP-CABLE-3/4"
|
|
|2
|-
|11
|HW0311
|BOLT-FHSCS-1/4-20 X 3/4"
|
|
|2
|-
|12
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|}

==== ''<big>Vacuum Extended Reach (Helical Actuator)</big>'' ====

===== '''''Non-Pivoting Cup Extended Reach Vacuum Arm (Helical Actuator) [Prior to October 2022]''''' =====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Non Pivoting Cup Extended Reach Vacuum Arm (Helical Actuator).png|alt=BE-SL & BE-DS Non-Pivoting Cup Extended Reach Vacuum Arm (Helical Actuator)|frameless|541x541px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41255005
|ARM-EXTENSION
|
|
|1
|-
|2
|41255004
|HOUSING-EXTENDED REACH
|
|
|1
|-
|3
|HC0416
|CYLINDER-2 1/2" X 12"
|
|
|1
|-
|4
|43057042
|PIN-CYLINDER-REAR
|
|
|1
|-
|5
|43057043
|PIN-CYLINDER-ROD
|
|
|1
|-
|6
|HW1132
|RETAINING RING-3/4" I.D.
|
|
|4
|-
|7
|H1578
|ADAPTER-90 DEG-#6 JIC X # 6 NPT
|
|
|2
|-
|8
|50057008
|PLATE-END
|
|
|1
|-
|9
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|10
|HW0104
|WASHER-FLAT-1/4"
|
|
|8
|-
|11
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|13
|HW0812
|SCREW-SHSS-1/4-20 X 5/8"-HALF DOG
|
|
|28
|-
|14
|HW0002
|NUT-HEX-1/4-20
|
|
|28
|-
|15
|41258002
|PLATE-BEARING
|80258001
|''Side''
|2
|-
|16
|41258005
|PLATE-SHIM
|80258001
|''Side''
|2
|-
|17
|41258003
|PLATE-BEARING
|80258001
|''Upper/Lower''
|2
|-
|18
|41258004
|PLATE-SHIM
|80258001
|''Upper/Lower''
|2
|}

===== '''''[Current] Pivoting Cup Extended Reach Vacuum Arm''''' '''''(Helical Actuator) [October 2022 to Present]''''' =====
[[File:IOP-400 BE-SL&DS (10-23) Pivoting Cup Extended Reach Vaccum Arm (Helical Actuator).png|alt=BE-SL & BE-DS Pivoting Cup Extended Reach Vacuum Arm (Helical Actuator)|frameless|571x571px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43055011
|ARM-EXTENSION
|
|''Pivoting cup only''
|1
|-
|2
|43055012
|HOUSING-EXTENDED REACH
|
|''Pivoting cup only''
|1
|-
|3
|HC0415
|CYLINDER-2 1/2" X 8"
|
|
|1
|-
|4
|43057042
|PIN-CYLINDER-REAR
|
|
|1
|-
|5
|43057043
|PIN-CYLINDER-ROD
|
|
|1
|-
|6
|HW1132
|RETAINING RING-3/4" I.D.
|
|
|4
|-
|7
|H1578
|ADAPTER-90 DEG-#6 JIC X # 6 NPT
|
|
|2
|-
|8
|50057008
|PLATE-END
|
|
|1
|-
|9
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|10
|HW0104
|WASHER-FLAT-1/4"
|
|
|8
|-
|11
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|13
|HW0812
|SCREW-SHSS-1/4-20 X 5/8"-HALF DOG
|
|
|24
|-
|14
|HW0002
|NUT-HEX-1/4-20
|
|
|24
|-
|15
|43058013
|PLATE-BEARING
|
|''Side''
|2
|-
|16
|43058016
|PLATE-SHIM
|
|''Side''
|2
|-
|17
|43058014
|PLATE-BEARING
|
|''Upper/ Lower''
|2
|-
|18
|43058015
|PLATE-SHIM
|
|''Upper/ Lower''
|2
|-
|19
|HW1043
|CLAMP-CYLINDER
|
|
|2
|-
|20
|43058019
|SUPPORT-CABLE-BAND CLAMP
|
|
|2
|-
|21
|E0622
|RESTRAINT-1/2"
|
|''Grip size .450" to .560"''
|2
|-
|22
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|2
|-
|23
|HW0104
|WASHER-FLAT-1/4"
|
|
|4
|-
|24
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|}

==== ''<big>'''Magnet Extended Reach (Helical Actuator)'''</big>'' ====

===== '''''[Discontinued] Extended Reach Magnet Arm (Helical Actuator) [Prior to October 2022]''''' =====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Extended Reach Magnet Arm (Helical Actuator).png|alt=BE-SL & BE-DS Discontinued Extended Reach Magnet Arm (Helical Actuator)|frameless|531x531px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43055011
|ARM-EXTENSION
|
|
|1
|-
|2
|43055012
|HOUSING-EXTENDED REACH
|
|
|1
|-
|3
|HC0415
|CYLINDER-2 1/2" X 8"
|
|
|1
|-
|4
|43057042
|PIN-CYLINDER-REAR
|
|
|1
|-
|5
|43057043
|PIN-CYLINDER-ROD
|
|
|1
|-
|6
|HW1132
|RETAINING RING-3/4" I.D.
|
|
|4
|-
|7
|H1578
|ADAPTER-90 DEG-#6 JIC X # 6 NPT
|
|
|2
|-
|8
|50057008
|PLATE-END
|
|
|1
|-
|9
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|10
|HW0104
|WASHER-FLAT-1/4"
|
|
|8
|-
|11
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|13
|HW0812
|SCREW-SHSS-1/4-20 X 5/8"-HALF DOG
|
|
|24
|-
|14
|HW0002
|NUT-HEX-1/4-20
|
|
|24
|-
|15
|43058013
|PLATE-BEARING
|
|''Side''
|2
|-
|16
|43058016
|PLATE-SHIM
|
|''Side''
|2
|-
|17
|43058014
|PLATE-BEARING
|
|''Upper / Lower''
|2
|-
|18
|43058015
|PLATE-SHIM
|
|''Upper / Lower''
|2
|-
|19
|HW1043
|CLAMP-CYLINDER
|
|
|2
|-
|20
|43058019
|SUPPORT-CABLE-BAND CLAMP
|
|
|2
|-
|21
|PL0501
|GROMMET-1/2" I.D.
|
|
|4
|-
|22
|HW0104
|WASHER-FLAT-1/4"
|
|
|4
|-
|23
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|24
|43057004-2
|SUPPORT-CABLE-MAGNET
|
|
|2
|}

===== ''[Current] Extended Reach Magnet Arm (Helical Actuator) [October 2022 to Present]'' =====
[[File:IOP-400 BE-SL&DS (10-23) Current Extended Reach Magnet Arm (Helical Actuator).png|alt=BE-SL & BE-DS Current Extended Reach Magnet Arm (Helical Actuator)|frameless|532x532px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|50055004
|ARM-EXTENSION
|
|
|1
|-
|2
|50055005
|HOUSING-EXTENDED REACH
|
|
|1
|-
|3
|HC0415
|CYLINDER-2 1/2" X 8"
|
|
|1
|-
|4
|43057042
|PIN-CYLINDER-REAR
|
|
|1
|-
|5
|43057043
|PIN-CYLINDER-ROD
|
|
|1
|-
|6
|HW1132
|RETAINING RING-3/4" I.D.
|
|
|4
|-
|7
|H1578
|ADAPTER-90 DEG-#6 JIC X # 6 NPT
|
|
|2
|-
|8
|50057008
|PLATE-END
|
|
|1
|-
|9
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|10
|HW0104
|WASHER-FLAT-1/4"
|
|
|8
|-
|11
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|13
|HW0812
|SCREW-SHSS-1/4-20 X 5/8"-HALF DOG
|
|
|20
|-
|14
|HW0002
|NUT-HEX-1/4-20
|
|
|20
|-
|15
|50058009
|PLATE-BEARING
|
|''Side''
|2
|-
|16
|50058012
|PLATE-SHIM
|
|''Side''
|2
|-
|17
|50058010
|PLATE-BEARING
|
|''Upper/ Lower''
|2
|-
|18
|50058011
|PLATE-SHIM
|
|''Upper/ Lower''
|2
|-
|19
|HW1043
|CLAMP-CYLINDER
|
|
|2
|-
|20
|43058019
|SUPPORT-CABLE-BAND CLAMP
|
|
|2
|-
|21
|PL0501
|GROMMET-1/2" I.D.
|
|
|4
|-
|22
|HW0104
|WASHER-FLAT-1/4"
|
|
|4
|-
|23
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|24
|43057004-2
|SUPPORT-CABLE-MAGNET
|
|
|2
|}

== <big>Floor Drive & Casters</big> ==

=== <big>Drive Wheel Assembly</big> ===

==== ''<big>Discontinued Drive Wheel Assembly (Prior to November 2012)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Drive Wheel Assembly.png|alt=BE-SL & BE-DS Discontinued Drive Wheel Assembly (Prior to November 2012)|frameless|540x540px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43715012
|FRAME-FLOOR DRIVE
|
|
|2
|-
| rowspan="2" |2
|HW0515
|BOLT-HHCS-1/2-13 X 2"-FULL THREAD
|
|
|6
|-
|HW0517
|BOLT-HHCS-1/2-13 X 2 1/2"-FULL THREAD
|
|''Cylinder support bracket bolt''
|2
|-
|3
|HW0110
|WASHER-LOCK-1/2"
|
|
|8
|-
|4
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|8
|-
|5
|C0050-2
|WHEEL-8" X 3"-POLY
|80222001
|
|2
|-
|6
|PT0406
|FLANGE BEARING-4 BOLT-1 3/16"
|80222001
|''Alloy casting''
|4
|-
|7
|HW0504
|BOLT-HHCS-1/2-13 X 2"
|
|
|8
|-
|8
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|8
|-
|9
|HW0110
|WASHER-LOCK-1/2"
|
|
|24
|-
|10
|HW0007
|NUT-HEX-1/2-13
|
|
|24
|-
|11
|43797001
|ROD-THREADED-1/2-13 X 7"
|
|
|8
|-
|12
|43727007
|SPACER-DRIVE WHEEL
|
|
|8
|-
|13
|43727006
|PLATE-MOTOR MOUNTING
|
|
|2
|-
|14
|N/A
|SHAFT-WHEEL
|
|''† See notes''
|2
|-
|15
|43097005
|KEY-1/4" X 3"
|80222001
|
|2
|-
|16
|00197028
|KEY-1/4" X 1 1/4"
|
|
|2
|-
|17
|N/A
|BUSHING-TAPER LOCK-1 3/16"
|
|''†'' ''Shaft side''
|2
|-
|18
|N/A
|COUPLING BODY-TAPER BORE-#50
|
|''†'' ''See notes''
|4
|-
|19
|HW0323
|BOLT-HHCS-5/16-18 X 1"
|80222001
|
|16
|-
|20
|PT0321
|CHAIN-COUPLING-#50
|
|''Includes Connecting Pin''
|2
|-
|21
|N/A
|BUSHING-TAPER LOCK-1"
|
|''†'' ''Motor side''
|2
|-
|22
|N/A
|MOTOR-HYDRAULIC-160CC
|
|''†'' ''See notes''
|2
|-
|23
|HW1071
|KEY-WOODRUFF-#808 STD
|
|
|2
|-
|24
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|8
|-
|25
|HW0107
|WASHER-LOCK-3/8"
|
|
|8
|-
|26
|H1547
|ADAPTER-#8 JICM X #10 SAEM
|
|
|4
|-
|27
|43017051
|SHIM-CASTER-1/2"
|
|''Used on Frame #'s 620 and up''
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Parts obsolete and no longer available. Spline Drive Conversion Kit PT# 80222003 required. Reuse of Bushing after disassembly NOT recommended.''
|}

==== ''<big>Discontinued Drive Wheel Assembly (November 2012 to November 2013)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Drive Wheel Assembly Used Nov 2012 to Nov 2013.png|alt=BE-SL & BE-DS Discontinued Drive Wheel Assembly (November 2012 to November 2013))|frameless|580x580px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43715012
|FRAME-FLOOR DRIVE
|
|
|2
|-
|2
|C0050-2
|WHEEL-8" X 3"-POLY
|80222001
|
|2
|-
|3
|PT0406
|FLANGE BEARING-4 BOLT-1 3/16"
|80222001
|''Alloy casting''
|4
|-
|4
|HW0504
|BOLT-HHCS-1/2-13 X 2"
|
|
|8
|-
|5
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|8
|-
|6
|HW0110
|WASHER-LOCK-1/2"
|
|
|24
|-
|7
|HW0007
|NUT-HEX-1/2-13
|
|
|24
|-
|8
|43797001
|ROD-THREADED-1/2-13 X 7"
|
|
|8
|-
|9
|43727007
|SPACER-DRIVE WHEEL
|
|''Must be ordered as a set of 4''
|8
|-
|10
|43727006
|PLATE-MOTOR MOUNTING
|
|
|2
|-
|11
|80222002
|SHAFT-WHEEL
|
|''†† Includes Coupling Body''
|2
|-
|12
|43097005
|KEY-1/4" X 3"
|80222001
|
|2
|-
|13
|N/A
|COUPLING BODY-TAPER BORE-#50
|
|''†'' ''See notes''
|2
|-
|14
|HW0323
|BOLT-HHCS-5/16-18 X 1"
|
|
|8
|-
|15
|PT0321
|CHAIN-COUPLING-#50
|
|''Includes Connecting Pin''
|2
|-
|16
|N/A
|BUSHING-TAPER LOCK-1"
|
|''†'' ''See notes''
|2
|-
|17
|N/A
|MOTOR-HYDRAULIC-160CC
|
|''†'' ''See notes''
|2
|-
|18
|HW1071
|KEY-WOODRUFF-#808 STD
|
|
|2
|-
|19
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|8
|-
|20
|HW0107
|WASHER-LOCK-3/8"
|
|
|8
|-
|21
|H1547
|ADAPTER-#8 JICM X #10 SAEM
|
|
|4
|-
|22
|HW1111
|RETAINING RING-1 3/16"
|
|''††'' ''Available in multiple kits''
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''†'' ''Parts obsolete and no longer available. Spline Drive Conversion Kit PT# 80222003 required. Reuse of Bushing after disassembly NOT recommended.''
|-
| colspan="6" |''†† Parts included in multiple kits''
|}

==== ''<big>Current Drive Wheel Assembly for BE-24 & BE-36 units (November 2013 to Present) & Discontinued Drive Wheel Assembly for BE-42 units (November 2013 to August 2021)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Current Drive Wheel Assembly BE-24 and BE-36 and Discontinued for BE-42 (used Nov 2013 to August 2021).png|alt=BE-SL & BE-DS Current Drive Wheel Assembly BE-24 and BE-36 and Discontinued for BE-42 (used Nov 2013 to August 2021)|frameless|579x579px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43722002-6B-1
|FLOOR DRIVE ASSEMBLY
|
|''Includes Items 1 through 19''
|2
|-
|1
|43715012
|FRAME-FLOOR DRIVE
|
|
|2
|-
|2
|C0050-2
|WHEEL-8" X 3"-POLY
|80222001
|
|2
|-
|3
|PT0406
|FLANGE BEARING-4 BOLT-1 3/16"
|80222001
|''Alloy casting''
|4
|-
|4
|HW0504
|BOLT-HHCS-1/2-13 X 2"
|
|
|8
|-
|5
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|8
|-
|6
|HW0110
|WASHER-LOCK-1/2"
|
|
|24
|-
|7
|HW0007
|NUT-HEX-1/2-13
|
|
|24
|-
|8
|43797001
|ROD-THREADED-1/2-13 X 7"
|
|
|8
|-
|9
|43727007
|SPACER-DRIVE WHEEL
|
|''Must be ordered as a set of 4''
|8
|-
|10
|43727006
|PLATE-MOTOR MOUNTING
|
|
|2
|-
|11
|80222002
|SHAFT-WHEEL
|†
|''Includes Coupling Body''
|2
|-
|12
|43097005
|KEY-1/4" X 3"
|80222001
|
|2
|-
|13
|PT0330
|COUPLING BODY-#50-SPLINE BORE
|80222003
|
|2
|-
|14
|PT0321
|CHAIN-COUPLING-#50
|
|''Includes Connecting Pin''
|2
|-
|15
|HC0120-6B-1
|MOTOR-HYDRAULIC-160CC
|80222003
|''Spline Shaft''
|2
|-
|16
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|8
|-
|17
|HW0107
|WASHER-LOCK-3/8"
|
|
|8
|-
|18
|HW1111
|RETAINING RING-1 3/16"
|†
|
|2
|-
|19
|H1547
|ADAPTER-#8 JICM X #10 SAEM
|
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Parts included in multiple kits.''
|}

==== ''<big>Current Radial Piston Drive Wheel Assembly for BE-42 units (August 2021 to Present)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Current Radial Piston Assembly for all BE-42 (shipped August 2021 to Present).png|alt=Current Radial Piston Assembly for all BE-42 (shipped August 2021 to Present)|frameless|548x548px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43822005
|RADIAL PISTON DRIVE WHEEL ASSEMBLY
|
|''Includes Items 1 through 6''
|2
|-
|1
|43825003
|RADIAL PISTON DRIVE WHEEL MOUNT
|
|
|1
|-
|2
|HC0160-1
|400CC RADIAL PISTON MOTOR
|
|''Includes Nuts & Studs''
|1
|-
|REF
|HC0160-STUD
|STUD-M14-1.5 X 46MM
|
|''Replacement Motor Stud''
|A/R
|-
|REF
|HC0160-NUT
|NUT-FLANGED HEX-M14-1.5
|
|''Replacement Motor Nut''
|A/R
|-
|3
|C0511
|WHEEL-POLY-10 X 5"-FLANGE MOUNT
|
|
|1
|-
|4
|HW0514
|BOLT-HHCS-1/2-13 X 2 1/2"
|
|
|6
|-
|5
|HW0110
|WASHER-LOCK-1/2"
|
|
|6
|-
|6
|HW0007
|NUT-HEX-1/2-13
|
|
|6
|-
|7
|H1612
|ADAPTER-H-90 DEG-#10 SAEM X #8 JICM
|
|
|2
|-
|8
|H1539
|ADAPTER-#8 JIC X #6 SAE
|
|
|1
|-
|9
|H1586
|ADAPTER-90 DEG-#8 JICSW X #6 NPT
|
|
|1
|-
|10
|H0801
|TEE-H-#6 NPT
|
|
|1
|-
|11
|H1501
|ADAPTER-#8 JIC X #6 NPT
|
|
|1
|-
|12
|H0200
|REDUCER-#6 NPT X #4 NPT
|
|
|1
|-
|13
|H0206
|PLUG-#4 NPT
|
|''† Left (LH) Drive Wheel only''
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Plug used on Left Drive Wheel Assembly only. Hose from Left Drive Wheel Assembly is connected to Tee on Right Drive Wheel Assembly.''
|}

=== <big>Idler Casters</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Idler Casters.png|alt=BE-SL & BE-DS Idler Casters|frameless|554x554px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|C0220-1
|CASTER-8" X 3"-POLY
|
|
|2
|-
|2
|43017022
|SHIM-CASTER-1/4"
|
|
|2
|-
|3
|43017051
|SHIM-CASTER-1/2"
|
|''Used on Frame #'s 620 and Up''
|2
|-
|4
|HW0517
|BOLT-HHCS-1/2-13 X 2 1/2"-FULL THREAD
|
|
|6
|-
|5
|HW0518
|BOLT-HHCS-1/2-13 X 3"-FULL THREAD
|
|''Cylinder Support Bracket Bolt''
|2
|-
|6
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|16
|-
|7
|HW0110
|WASHER-LOCK-1/2"
|
|
|8
|-
|8
|HW0007
|NUT-HEX-1/2-13
|
|
|8
|}

== <big>Electrical</big> ==

=== <big>AC Power Stanchion</big> ===

==== ''<big>BE-SL Aero-Motive Energy Rail</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL Aero-Motive Energy Rail.png|alt=BE-SL Aero-Motive Energy Rail|frameless|540x540px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43635001
|STANCHION-POWER
|
|''114" O.A.L.''
|1
|-
|2
|HW1030
|U-BOLT-3/8-16 X 2" X 5"
|
|''Square bend''
|3
|-
|3
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|6
|-
|4
|HW0107
|WASHER-LOCK-3/8"
|
|
|6
|-
|5
|HW0005
|NUT-HEX-3/8-16
|
|
|6
|-
|6
|46837014-2
|TOW ARM-COLLECTOR TROLLEY
|
|
|1
|-
|7
|46838015
|SPACER BLOCK-TOW ARM
|
|
|1
|-
|8
|E0632
|RESTRAINT-3/4"
|
|''Grip size .625" to .750"''
|1
|-
|9
|E0618
|LOCKNUT-CONDUIT-3/4"
|
|
|1
|-
|10
|E0612
|COVER-JUNCTION BOX
|
|''Included with Item 1''
|1
|-
|11
|HW1051
|EYE BOLT-3/16-16 X 5 1/2"
|
|
|2
|-
|12
|HW0126
|WASHER-FLAT-3/8"-FENDER
|
|
|4
|-
|13
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|14
|HW0005
|NUT-HEX-3/8-16
|
|
|4
|-
|15
|E1105
|JUNCTION BOX-4" X 2" X 2"
|
|''Weatherproof''
|1
|-
|16
|E1106
|COVER-JUNCTION BOX
|
|''Weatherproof with Gasket''
|1
|-
|17
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
|18
|E0608-1
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .450" to .560"''
|1
|-
|19
|E0622
|RESTRAINT-1/2"
|
|''Grip size.450" to .560"''
|1
|-
|20
|BD0010
|TROLLEY-ENERGY RAIL
|
| rowspan="2" |''Aero-Motive Rail only''

''(Orange housing color)''
|1
|-
|21
|BD0100
|BRUSH-TROLLEY
|
|4
|}

==== ''<big>BE-DS Aero-Motive Energy Rail</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-DS Aero-Motive Energy Rail.png|alt=BE-DS Aero-Motive Energy Rail|frameless|553x553px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43735001
|STANCHION-POWER
|
|
|1
|-
|2
|HW1030
|U-BOLT-3/8-16 X 2" X 5"
|
|''Square bend''
|3
|-
|3
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|6
|-
|4
|HW0107
|WASHER-LOCK-3/8"
|
|
|6
|-
|5
|HW0005
|NUT-HEX-3/8-16
|
|
|6
|-
|6
|46837014-2
|TOW ARM-COLLECTOR TROLLEY
|
|
|1
|-
|7
|46838015
|SPACER BLOCK-TOW ARM
|
|
|1
|-
|8
|E0632
|RESTRAINT-3/4"
|
|''Grip size .625" to .750"''
|1
|-
|9
|E0618
|LOCKNUT-CONDUIT-3/4"
|
|
|1
|-
|10
|E0612
|COVER-JUNCTION BOX
|
|''Included with Item 1''
|1
|-
|11
|HW1051
|EYE BOLT-3/16-16 X 5 1/2"
|
|
|2
|-
|12
|HW0126
|WASHER-FLAT-3/8"-FENDER
|
|
|4
|-
|13
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|14
|HW0005
|NUT-HEX-3/8-16
|
|
|4
|-
|15
|E1105
|JUNCTION BOX-4" X 2" X 2"
|
|''Weatherproof''
|1
|-
|16
|E1106
|COVER-JUNCTION BOX
|
|''Weatherproof with Gasket''
|1
|-
|17
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
|18
|E0608-1
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .450" to .560"''
|1
|-
|19
|E0622
|RESTRAINT-1/2"
|
|''Grip size.450" to .560"''
|1
|-
|20
|BD0010
|TROLLEY-ENERGY RAIL
|
| rowspan="2" |''Aero-Motive Rail only''

''(Orange housing color)''
|1
|-
|21
|BD0100
|BRUSH-TROLLEY
|
|4
|}

==== ''<big>Vahle Energy Rail</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Vahle Energy Rail.png|alt=BE-SL & BE-DS Vahle Energy Rail|frameless|555x555px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1A
|BD0031
|TROLLEY-ENERGY RAIL, KSL
|
| rowspan="3" |''† Vahle KSL Rail only''

''(Green housing color)''
|1
|-
|2A
|BD0040
|BRUSH-PHASE, KSL
|
|3
|-
|3A
|BD0041
|BRUSH-GROUND, KSL
|
|1
|-
|1B
|BD0231
|TROLLEY-ENERGY RAIL, KBH
|
| rowspan="3" |''† Vahle KBH Rail only''

''(Gray housing color)''

''(Not shown)''
|1
|-
|2B
|BD0240
|BRUSH-PHASE, KBH
|
|3
|-
|3B
|BD0241
|BRUSH-GROUND, KBH
|
|1
|-
| rowspan="2" |4
|BD0030
|TOW ARM-COLLECTOR TROLLEY, KSL
|
|''†'' ''Vahle KSL Rail only''

''(Green housing color)''
|1
|-
|BD0230
|TOW ARM-COLLECTOR TROLLEY, KBH
|
|''†'' ''Vahle KBH Rail only''

''(Gray housing color)''
|1
|-
|5
|46838015
|SPACER-BLOCK-TOW ARM
|
|''†† See notes''
|1
|-
|6
|41237083-2
|BRACKET-TOW ARM
|
|''††'' ''See notes''
|1
|-
|7
|HW1054
|U-BOLT-5/16-18 X 2" X 5"-SQUARE BEND
|
|
|1
|-
|8
|HW0323
|BOLT-HHCS-5/16-18 X 1"
|
|
|2
|-
|9
|HW0106
|WASHER-FLAT-5/16"-SAE
|
|
|4
|-
|10
|HW0150
|WASHER-FLAT-5/16"-FENDER
|
|
|2
|-
|11
|HW0105
|WASHER-LOCK-5/16"
|
|
|4
|-
|12
|HW0004
|NUT-HEX-5/16-18
|
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Verify Energy Rail Type (KSL or KBH) by the color of the Energy Rail Housing.''
|-
| colspan="6" |''†† Not all units equipped with Tow Arm Bracket. Location of Spacer Block and/or Tow Arm Bracket may vary from configuration shown.''
|}

=== <big>Transformer & Magnet Starter</big> ===

==== <big>''Magnet Starter''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Magnet Starter.png|alt=BE-SL & BE-DS Magnet Starter|frameless|555x555px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0103
|MAGNETIC STARTER
|
|''NEMA 1''
|1
|-
|2
|E0608-1
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .450" to .560"''
|1
|-
|3
|E0623
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .250" to .375"''
|4
|-
|4
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|1
|-
|5
|E0622
|RESTRAINT-1/2"
|
|''Grip size .450" to .560"''
|1
|-
|6
|E0613
|RESTRAINT-3/4"
|
|''Grip size .500" to .625"''
|1
|-
|7
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|7
|-
|8
|E0618
|LOCKNUT-CONDUIT-3/4"
|
|
|1
|-
|9
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|3
|-
|10
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|7
|-
|11
|HW0103
|WASHER-LOCK-1/4'
|
|
|3
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|}

==== ''<big>Transformer</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Transformer.png|alt=BE-SL & BE-DS Transformer|frameless|537x537px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="2" |1
|80232002
|TRANSFORMER-480V:120V-1.5 KVA
|
|''†'' ''See notes''
|1
|-
|E0220
|TRANSFORMER-480V:120V-3.0 KVA
|
|''††'' ''See notes''
|1
|-
|2
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|2
|-
|3
|E0617
|LOCKNUT-CONDUIT-1/2
|
|''(Not shown)''
|2
|-
|4
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|5
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|8
|-
|6
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|7
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|8
|00196401
|LABEL-DANGER-480V
|
|''(Not shown)''
|1
|-
|9
|00196408
|LABEL-DANGER-DISCONNECT POWER
|
|''(Not shown)''
|1
|-
! colspan="6" |NOTE
|-
| colspan="6" |''† 1.5 Kva Transformer used on units shipped prior to February 2020.''
|-
| colspan="6" |''†† 3.0 Kva Transformer used on units shipped 2020 to Present.''
|-
| colspan="6" |''Verify Transformer rating prior to ordering replacement.''
|}

=== <big>Operator Console</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Operator Console Parts.png|alt=BE-SL & BE-DS Operator Console Parts Diagram|frameless|544x544px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0327
|KEYED ACTUATOR ASSEMBLY
|
|''Includes 2 Keys & Contact Block''
|1
|-
|2
|E0351
|KEY-REPLACEMENT
|
|''Set of 2 Keys''
|A/R
|-
|3
|E0309-1
|HOUR METER
|
|''† Includes Mounting Hardware''
|1
|-
|4
|N/A
|SWITCH-SELECTOR-3 POSITION
|
|''ON-OFF-ON, †† See notes''
|1
|-
| rowspan="2" |5
|N/A
|LEGEND PLATE-VACUUM
|
|''†††'' ''See notes''
|1
|-
|N/A
|LEGEND PLATE-MAGNET
|
|''†††'' ''See notes''
|1
|-
|6
|N/A
|CONTACT BLOCK-N/O
|
|''††'' ''See notes''
|2
|-
|7
|N/A
|CONTACT BLOCK-N/C
|
|''††'' ''See notes''
|2
|-
|8
|E1083
|SWITCH-SELECTOR-3 POSITION
|80232001
|''OFF-ON-OFF''
|1
|-
|9
|E1080
|CONTACT BLOCK-N/O & N/C
|80232001
|
|2
|-
|10
|YE0311
|SWITCH-EMERGENCY STOP
|
|
|1
|-
|11
|YE0407
|LEGEND PLATE-EMERGENCY STOP
|
|
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Current hour meter is 3-Bolt version. Replacement of 4-Bolt version will require new mounting holes to be drilled in Dashboard.''
|-
| colspan="6" |''†† Parts no longer available. Must order new Selector Switch Kit 80232001.''
|-
| colspan="6" |''††† Parts no longer available. See [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#BE-SL_Labels BE-SL Labels] and [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#BE-DS_Labels BE-DS Labels] sections for current Placards.''
|}

=== <big>Switches</big> ===

==== ''<big>Foot Switch</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Foot Switch.png|alt=BE-SL & BE-DS Foot Switches|frameless|726x726px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0301-1
|SWITCH-FOOT OPERATED
|
|''†'' ''See notes''
|1
|-
|2
|E0613
|RESTRAINT-3/4"
|
|''Grip size .500" to .625"''
|1
|-
|3
|E0515
|CORD-14-3-SO/SOW
|
|
|9'
|-
|4
|HC0303
|BOLT-HHCS-1/4-20 X 1"
|
|''If equipped''
|2
|-
|5
|HC0103
|WASHER-1/4"-LOCK
|
|''If equipped''
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Open-Style Switch is a direct replacement for discontinued, Covered-Style Switch.''
|}

==== ''<big>Gate Switch</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Gate Switch.png|alt=BE-SL & BE-DS Gate Switches|frameless|549x549px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0312
|SWITCH-PUSH BUTTON
|
|
|1
|-
|2
|43017041
|MOUNT-GATE SWITCH
|
|
|1
|-
|3
|HW1077
|SCREW-RHMS-#10-24 X 5/8"
|
|
|2
|-
|4
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|2
|-
|5
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|6
|HW0307
|BOLT-SHCS-1/4-20 X 1"
|
|
|2
|-
|7
|PL0502
|GROMMET-3/8" I.D.
|
|
|1
|-
|8
|YE0305
|SWITCH-ROLLER
|
|
|1
|-
|9
|SS0303
|WASHER-FLAT-#8
|
|
|2
|-
|10
|SS0111
|SCREW-SHCS-#8-32 X 1 1/2"
|
|
|2
|-
|11
|SS0203
|NUT-NILN-#8-32
|
|''Used on BE-DS only''
|2
|-
|12
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|1
|}

==== ''<big>Proximity Switch</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Proximity Switch.png|alt=BE-SL & BE-DS Proximity Switch|frameless|533x533px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0314
|SENSOR-PROXIMITY-30MM
|
|
|1
|-
|2
|43017027-2
|BRACKET-PROXIMITY SENSOR
|
|
|1
|-
|3
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|2
|-
|4
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|5
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|-
| rowspan="2" |6
|43017037-2
|ANGLE-PROXIMITY SENSOR TARGET
|
|''Rotary Actuator units''
|1
|-
|43017084-2
|ANGLE-PROXIMITY SENSOR TARGET
|
|''Helical Actuator units''
|1
|-
|7
|HW0311
|BOLT-FHSCS-1/4-20 X 3/4"
|
|
|2
|}

=== <big>Junction Boxes</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Junction Box Diagram.png|alt=BE-SL & BE-DS Junction Box |frameless|554x554px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0611
|JUNCTION BOX-4" X 2" X 2"
|
|
|2
|-
|2
|E0612
|COVER-JUNCTION BOX
|
|
|2
|-
|3
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|4
|-
|4
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|6
|-
|5
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|6
|}

=== <big>Fusing</big> ===

==== <big>''Primary Fusing (June 2007 to Present)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Primary Fusing.png|alt=BE-SL & BE-DS Primary Fusing (Effective June 2207 to Present)|frameless|550x550px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43036001
|JUNCTION BOX-4" X 4" X 2"
|
|''Includes Cover''
|1
|-
|2
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|2
|-
|3
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|2
|-
|4
|HW0301
|BOLT-HHCS-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
|5
|E1131
|FUSE HOLDER
|
|
|2
|-
|6
|HW0135
|SCREW-RHMS-#8-32 X 3/4"
|
|
|4
|-
|7
|HW0132
|NUT-NILN-#8-32
|
|
|4
|-
|8
|X350057
|FUSE-4 AMP
|
|
|2
|}

==== <big>''Secondary Fusing''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Secondary Fusing.png|alt=BE-SL & BE-DS Secondary Fusing|frameless|571x571px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0323
|FUSE HOLDER
|
|
|1
|-
|2
|E0914
|FUSE-10 AMP
|
|
|1
|-
|3
|HW0130
|SCREW-RHMS-#8-32 X 1/2"
|
|
|2
|-
|4
|E0132
|NUT-NILN-#8-32
|
|''(Not shown)''
|2
|-
|5
|43096008
|LEGEND PLATE "...10 AMP FUSE..."
|
|''(Not shown)''
|1
|}

=== <big>120V Receptacle</big> ===
[[File:IOP-400 BE-SL&DS (10-23) 120V Receptacle.png|alt=BE-SL & BE-DS 120V Receptacle|frameless|539x539px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0611
|JUNCTION BOX-4" X 2" X 2"
|
|
|1
|-
|2
|E0622
|RESTRAINT-1/2"
|
|''Grip size .450" to .560"''
|1
|-
|3
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|1
|-
|4
|E0650
|RECEPTACLE-DUPLEX
|
|''†20A''
|1
|-
|5
|E0651
|COVER-RECEPTACLE-DUPLEX
|
|
|1
|-
|6
|E0655
|RECEPTACLE-GFCI
|
|''20A''
|1
|-
|7
|E0656
|COVER-RECEPTACLE-GFCI
|
|
|1
|-
|8
|E0654
|JUNCTION BOX-4" X 4" X 2"
|
|
|1
|-
|9
|E0657
|COVER-RECEPTACLE-DUPLEX/GFCI
|
|
|1
|-
|10
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|''Mounting Hardware (Not shown)''
|A/R
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† If Duplex Receptacle has Split Feed (1 set of black and white wires for each plug), the Break-Off Fin must be removed prior to installation.''
|}

=== <big>Wiring Diagrams & Schematics</big> ===

==== '''<big>''BE-SL & BE-DS Electrical Schematic''</big>''' ====
[[File:IOP-400 BE-SL&DS (10-23) Wiring Diagram 1.png|alt=BE-SL & BE-DS Electrical Schematic|frameless|900x900px]]

==== '''<big>''[Discontinued] BE-SL & BE-DS with Water Cart Wiring Diagram (Prior to October 10, 2012)''</big>''' ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued BE-SL and BE-DS with Water Cart Wiring Diagram.png|alt=Discontinued BE-SL and BE-DS with Water Cart Wiring Diagram|frameless|900x900px]]

==== '''<big>''[Current] BE-SL & BE-DS with Auxiliary Receptacle Wiring Diagram (October 10, 2012 to Present)''</big>''' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL and BE-DS with Auxiliary Receptacle Wiring Diagram.png|alt=Current BE-SL and BE-DS with Auxiliary Receptacle Wiring Diagram|frameless|897x897px]]

'''<big>''BE-SL & BE-DS Magnet Extraction Wiring Diagram''</big>'''

[[File:IOP-400 BE-SL&DS (10-23) BE-SL & BE-DS with Magnet Wiring Diagram.png|alt=BE-SL and BE-DS with Magnet Wiring Diagram|frameless|897x897px]]

== <big>Hydraulics</big> ==

=== <big>Power Unit & Riser</big> ===

==== <big>''Power Unit''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL and BE-DS Power Unit.png|alt=BE-SL & BE-DS Power Unit|frameless|547x547px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0003
|MOTOR-ELECTRIC-5 HP
|
|
|1
|-
|2
|HC0305
|ADAPTER
|
|''Pump-to-Motor''
|1
|-
|3
|HC0319
|PUMP-VARIABLE DISPLACEMENT-7.5 GPM
|
|''Vane Type''
|1
|-
|4
|HC0313
|COUPLING BODY-1 1/8"
|
|''Motor end''
|1
|-
|5
|HC0312
|SPIDER-COUPLING INSERT
|
|
|1
|-
|6
|HC0311
|COUPLING BODY-3/4"
|
|''Pump end''
|1
|-
|7
|H1606
|ADAPTER-90 DEG-#8 JICM X #8 SAEM
|
|
|1
|-
|8
|H1603
|ADAPTER-90 DEG-#16 JICM X #16 SAEM
|
|
|1
|-
|9
|H1650
|BUSHING-RED-#12 SAEM X #8 SAEF
|
|
|1
|-
|10
|H1538
|UNION-#8 SAE
|
|
|1
|-
|11
|HC0261
|VALVE-MAIN SYSTEM PRESSURE
|
|
|1
|-
|11a
|43646004
|REPLACEMENT CARTRIDGE
|
|''† For Item 11 (Not shown)''
|A/R
|-
|12
|HC0318
|GAUGE-PRESSURE
|
|''0-3000 LBS''
|1
|-
|13
|H0206
|PLUG-#4 NPT
|
|
|1
|-
|14
|H1551
|ADAPTER-#12 JICM X #8 SAEM
|
|
|1
|-
|15
|H1540
|ADAPTER-#8 JICM X #8 SAEM
|
|
|1
|-
|16
|E0613
|RESTRAINT-3/4"
|
|''Grip size .500" to .625"''
|1
|-
|17
|E0618
|LOCKNUT-CONDUIT-3/4"
|
|''(Not shown)''
|1
|-
|18
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
| rowspan="4" |''Mounting Hardware (Not shown)''

''Used on all BE-SL''

''See [https://tech.bhs1.com/index.php/(BE-SL_%26_-DS)_Single_Level_%26_Double_Stack_Operator_Aboard_Battery_Extractors_%E2%80%93_Parts_%26_Service_Manual_(IOP-400)#Power_Unit_Riser Power Unit Riser] section for BE-DS Mounting Hardware''
|4
|-
|19
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|8
|-
|20
|HW0107
|WASHER-LOCK-3/8"
|
|4
|-
|21
|HW0005
|NUT-HEX-3/8-16
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Cartridges are for replacement only.''
|}

==== <big>''Power Unit Riser''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-DS Motor Riser.png|alt=BE-DS Motor Riser used on Frame #'s 368 to Present|frameless|617x617px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43717061-2
|RISER-MOTOR
|
|''Frames #'s 368 to Present''
|1
|-
|2
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
| rowspan="4" |''Mounting Hardware for BE-DS Frames #'s 367 and Earlier''
|4
|-
|3
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|8
|-
|4
|HW0107
|WASHER-LOCK-3/8"
|
|4
|-
|5
|HW0005
|NUT-HEX-3/8-16
|
|4
|-
|6
|HW0302
|BOLT-HHCS-1/4-20 X 3/4"
|
| rowspan="4" |''Mounting Hardware for BE-DS Frames #'s 368 to Present (Not shown)''
|4
|-
|7
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|8
|-
|8
|HW0103
|WASHER-LOCK-1/4"
|
|4
|-
|9
|HW0002
|NUT-HEX-1/4-20
|
|4
|}

=== <big>Reservoir</big> ===

==== <big>''BE-SL 18 Gallon Reservoir''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL 18 Gallon Reservoir.png|alt=BE-SL 18 Gallon Reservoir|frameless|543x543px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43642002
|RESERVOIR ASSEMBLY
|
|''† Includes Items 1 through 9''
|1
|-
|1
|HC0542
|GASKET-CHANNEL
|
|''Sold by length''
|8'
|-
|2
|HC0340
|GAUGE-SIGHT
|
|''With Thermometer''
|1
|-
|3
|HC0306
|STRAINER-SUCTION
|
|
|1
|-
|4
|HC0308
|FILLER/BREATHER ASSEMBLY
|
|''Includes Gaskets''
|1
|-
|5
|HW0209
|SCREW-RHMS-10-32 X 1/2"
|
|
|6
|-
|6
|BI0110
|ELBOW-STR-90 DEG-#16 NPT
|
|
|1
|-
|7
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|10
|-
|8
|BI0107
|ELBOW-STR-90 DEG-#12 NPT
|
|''† See notes''
|2
|-
|9
|H0208
|PLUG-#12 NPT
|
|
|1
|-
|10
|H1590
|ADAPTER-90 DEG-#16 JICM X #16 FNPT
|
|
|1
|-
|11
|BI0405
|CAP-#12 NPT
|
|
|1
|-
|12
|PB0311-1
|NIPPLE-#12 NPT X 2"-BRASS
|
|
|1
|-
|13
|HC0307
|RETURN LINE FILTER ASSEMBLY
|
|''Housing and Filter''
|1
|-
|14
|HC0317
|FILTER-RETURN LINE
|
|''Replacement Filter''
|1
|-
|15
|PB0310-1
|NIPPLE-CLOSE-#12 NPT-BRASS
|
|
|2
|-
|16
|BI0301
|TEE-#12 FNPT
|
|
|3
|-
|17
|H1502
|ADAPTER-#8 JICM X #12 NPTM
|
|
|3
|-
|18
|H1580
|ADAPTER-90 DEG-#8 JICM X #12 NPTM
|
|
|1
|-
|19
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
| rowspan="4" |''Mounting Hardware (Not shown)''
|4
|-
|20
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|8
|-
|21
|HW0107
|WASHER-LOCK-3/8"
|
|4
|-
|22
|HW0005
|NUT-HEX-3/8-16
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† One Elbow included with Reservoir Assembly.''
|}

==== <big>''[Current] BE-DS 18 Gallon Reservoir (February 2004 to Present)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Current BE-DS 18 Gallon Reservoir (February 2004 to Present).png|alt=Current BE-DS 18 Gallon Reservoir (February 2004 to Present)|frameless|540x540px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43642002
|RESERVOIR ASSEMBLY
|
|''†'' ''Includes Items 1 through 9''
|1
|-
|1
|HC0542
|GASKET-CHANNEL
|
|''Sold by length''
|8'
|-
|2
|HC0340
|GAUGE-SIGHT
|
|''With Thermometer''
|1
|-
|3
|HC0306
|STRAINER-SUCTION
|
|
|1
|-
|4
|HC0308
|FILLER/BREATHER ASSEMBLY
|
|''Includes Gaskets''
|1
|-
|5
|HW0209
|SCREW-RHMS-10-32 X 1/2"
|
|
|6
|-
|6
|BI0110
|ELBOW-STR-90 DEG-#16 NPT
|
|
|1
|-
|7
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|10
|-
|8
|BI0107
|ELBOW-STR-90 DEG-#12 NPT
|
|''†'' ''See notes''
|2
|-
|9
|H0208
|PLUG-#12 NPT
|
|
|1
|-
|10
|H1590
|ADAPTER-90 DEG-#16 JICM X #16 FNPT
|
|
|1
|-
|11
|BI0102
|ELBOW-90 DEG-#12 NPT
|
|
|3
|-
|12
|PB0311-1
|NIPPLE-#12 NPT X 2"-BRASS
|
|
|1
|-
|13
|HC0307
|RETURN LINE FILTER ASSEMBLY
|
|''Housing and Filter''
|1
|-
|14
|HC0317
|FILTER-RETURN LINE
|
|''Replacement Filter''
|1
|-
|15
|PB0310-1
|NIPPLE-CLOSE-#12 NPT-BRASS
|
|
|3
|-
|16
|BI0301
|TEE-#12 FNPT
|
|
|2
|-
|17
|H1502
|ADAPTER-#8 JICM X #12 NPTM
|
|
|4
|-
|18
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
| rowspan="4" |''Mounting Hardware (Not shown)''
|4
|-
|19
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|8
|-
|20
|HW0107
|WASHER-LOCK-3/8"
|
|4
|-
|21
|HW0005
|NUT-HEX-3/8-16
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''†'' ''One Elbow included with Reservoir Assembly.''
|}

==== <big>''[Discontinued] BE-DS 10 Gallon Reservoir (Prior to February 2004)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued BE-DS 10 Gallon Reservoir (Prior to February 2004).png|alt=Discontinued BE-DS 10 Gallon Reservoir (Prior to February 2004)|frameless|563x563px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43742001
|RESERVOIR ASSEMBLY
|
|''Includes Items 1 through 8''
|1
|-
|1
|HC0542
|GASKET-CHANNEL
|
|''Sold by length''
|7'
|-
|2
|HC0340
|GAUGE-SIGHT
|
|''With Thermometer''
|1
|-
|3
|HC0306
|STRAINER-SUCTION
|
|
|1
|-
|4
|HC0308
|FILLER/BREATHER ASSEMBLY
|
|''Includes Gaskets''
|1
|-
|5
|HW0209
|SCREW-RHMS-10-32 X 1/2"
|
|
|6
|-
|6
|BI0110
|ELBOW-STR-90 DEG-#16 NPT
|
|
|1
|-
|7
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|10
|-
|8
|H0208
|PLUG-#12 NPT
|
|
|1
|-
|9
|H1590
|ADAPTER-90 DEG-#16 JICM X #16 FNPT
|
|
|1
|-
|10
|BI0102
|ELBOW-90 DEG-#12 NPT
|
|
|2
|-
|11
|BI0020
|NIPPLE-#12 NPT X 3"
|
|
|1
|-
|12
|HC0307
|RETURN LINE FILTER ASSEMBLY
|
|''Housing and Filter''
|1
|-
|13
|HC0317
|FILTER-RETURN LINE
|
|''Replacement Filter''
|1
|-
|14
|PB0310-1
|NIPPLE-CLOSE-#12 NPT-BRASS
|
|
|2
|-
|15
|BI0301
|TEE-#12 FNPT
|
|
|3
|-
|16
|H1509
|ADAPTER-#10 JICM X #12 NPTM
|
|
|2
|-
|17
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
| rowspan="4" |''Mounting Hardware (Not shown)''
|4
|-
|18
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|8
|-
|19
|HW0107
|WASHER-LOCK-3/8"
|
|4
|-
|20
|HW0005
|NUT-HEX-3/8-16
|
|4
|}

==== <big>''[Discontinued] BE-DS Heat Exchanger (Frame #'s 367 and Earlier)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued BE-DS Heat Exchanger (Frame - 367 and Earlier).png|alt=Discontinued BE-DS Heat Exchanger (Frame # 367 and Earlier)|frameless|566x566px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0503
|HEAT EXCHANGER
|
|
|1
|-
|2
|BI0107
|ELBOW-STR-90 DEG-#12 NPT
|
|
|2
|-
|3
|H1509
|ADAPTER-#10 JICM X #12 NPTM
|
|
|1
|-
|4
|BI0002
|NIPPLE-CLOSE-#12 NPT
|
|
|1
|-
|5
|BI0105
|ELBOW-RED-90 DEG-#12 FNPT X #8 FNPT
|
|
|1
|-
|6
|BI0001
|NIPPLE-CLOSE-#8 NPT
|
|
|1
|-
|7
|BI0101
|ELBOW-90 DEG-#8 FNPT
|
|
|1
|-
|8
|BI0004
|NIPPLE-#8 NPT X 3"
|
|
|1
|-
|9
|BI0302
|TEE-#8 FNPT
|
|
|1
|-
|10
|H1507
|ADAPTER-#8 JICM X # 8 NPTM
|
|
|2
|-
|11
|HW0402
|BOLT-HHCS-3/8-16 X 1"
|
|
|4
|-
|12
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|8
|-
|13
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|14
|HW0005
|NUT-HEX-3/8-16
|
|
|4
|}

=== <big>Control Valve Assemblies</big> ===

==== <big>''Lift / Floor Drive / Arm Rotation Valve & Manifold Detail''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Lift + Floor Drive + Arm Rotation Valve & Manifold Detail.png|alt=BE-SL & BE-DS Lift / Floor Drive / Arm Rotation Valve & Manifold Detail|frameless|551x551px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0233
|VALVE-LEVER
|
|
|3
|-
|2
|HC0250
|MANIFOLD
|
|''3-Bank''
|1
|-
|3
|H1545
|ADAPTER-#10 JICM X #10 SAEM
|
|
|3
|-
|4
|H1641
|PLUG-#10 SAE
|
|
|1
|-
|5
|H1640
|PLUG-#6 SAE
|
|
|1
|-
|6
|H1606
|ADAPTER-90 DEG-#8 JICM X #8 SAEM
|
|
|2
|-
|7
|H1602
|ADAPTER-90 DEG-#8 JICM X #8 SAEM-LL
|
|
|2
|-
|8
|H1600
|ADAPTER-90 DEG-#6 JICM X #8 SAEM
|
|
|2
|-
|9
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|4
|-
|10
|H1587
|ADAPTER-#6 JICSW X #4 NPTM
|
|
|2
|-
|11
|HC0211
|VALVE-ADJUSTABLE FLOW CONTROL
|
|
|2
|-
|12
|H1504
|ADAPTER-#6 JICM X #4 NPTM
|
|
|2
|}

==== <big>''Rollers / Arm Traverse Valve & Manifold Detail''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Rollers + Arm Traverse Valve & Manifold Detaill.png|alt=BE-SL & BE-DS Rollers / Arm Traverse Valve & Manifold Detail|frameless|542x542px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0233
|VALVE-LEVER
|
|
|3
|-
|2
|HC0250
|MANIFOLD
|
|''3-Bank''
|1
|-
|3
|H1641
|PLUG-#10 SAE
|
|
|1
|-
|4
|H1610
|ADAPTER-90 DEG-#10 JICM X #10 SAEM
|
|
|2
|-
|5
|H1640
|PLUG-#6 SAE
|
|
|1
|-
|6
|H1000
|ADAPTER-#8 SAEM X #4 FNPT
|
|
|6
|-
|7
|H0001
|NIPPLE-#4 NPT
|
|
|4
|-
|8
|HC0247
|FIXED FLOW REGULATOR-2.25 GPM
|
|''†'' ''See notes''
|4
|-
|9
|H1504
|ADAPTER-#6 JICM X #4 NPTM
|
|
|6
|-
|10
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|4
|-
|11
|HC0233-SK
|SEAL KIT
|
|''For Item 1 (Not shown)''
|A/R
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Units built prior to January 2017 equipped with Adjustable Flow Controls. Fixed Flow Regulators are direct replacement for Adjustable Flow Controls.''
|}

=== <big>Lift Circuit</big> ===

==== <big>''Lift Cylinders''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL & BE-DS Lift Cylinders.png|alt=BE-SL & BE-DS Lift Cylinders|frameless|565x565px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
| rowspan="3" |1
|HC0403
|CYLINDER-LIFT, 2-1/2" X 20"
|
|''BE-SL only''
|4
|-
|HC0404
|CYLINDER-LIFT. 2-1/2" X 30"
|
|''BE-DS only. † See notes''
|4
|-
|HC0404-1
|CYLINDER-LIFT. 2-1/2" X 30"
|
|''BE-DS only. †† See notes''
|4
|-
|2
|H1578
|ADAPTER-#6 JICM X #6 NPTM
|
|
|4
|-
|3
|HC0426-1
|VELOCITY FUSE
|
|
|4
|-
|4
|H0302
|ELBOW-STR-90 DEG-#6 NPT
|
|
|4
|-
|5
|43722005
|CLEVIS ASSEMBLY
|
| rowspan="4" |''BE-DS only''
|4
|-
|6
|HW0407
|BOLT-HHCS-3/8-16 X 2 3/4"
|
|4
|-
|7
|HW0107
|WASHER-LOCK-3/8"
|
|4
|-
|8
|HW0005
|NUT-HEX-3/8-16
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† HC0404 valid for units shipped prior to December 2022.''
|-
| colspan="6" |''†† HC0404-1 valid for units shipped December 2022 to Present''
|}

==== <big>''[Current] Lift Circuit Configuration (Non-Interflow Manifold) [July 2003 to Present]''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Current Lift Circuit Configuration (Non-Interflow Manifold) (July 2003 to Present).png|alt=BE-SL & BE-DS Current Lift Circuit Configuration (Non-Interflow Manifold) [July 2003 to Present]|frameless|547x547px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0215
|VALVE-CHECK-CARTRIDGE
|
|
|8
|-
|2
|H1560
|ADAPTER-45 DEG-#8 JICM X #8 SAEM
|
|
|4
|-
|3
|H1670
|ADAPTER-45 DEG-#12 JICM X #10 SAEM
|
|
|1
|-
|4
|H1647
|ADAPTER-90 DEG-#10 SAEM X #8 FNPT
|
|
|1
|-
|5
|H0005
|NIPPLE-RED-#8 NPT X #6 NPT
|
|
|1
|-
|6
|HC0268
|VALVE-ADJUSTABLE FLOW CONTROL
|
|''Pressure compensated''
|1
|-
|7
|H1685
|ADAPTER-#10 JICM X #6 NPTM
|
|
|1
|-
|8
|H1690
|ADAPTER-#10 JICSW X #10 SAEM
|
|
|1
|-
|9
|H1612
|ADAPTER-90 DEG-#8 JICM X #10 SAEM
|
|
|1
|-
|10
|HC0282
|VALVE-COUNTER BALANCE
|
|
|1
|-
|10a
|43646005
|REPLACEMENT CARTRIDGE
|
|''† For Item 10 (Not shown)''
|A/R
|-
|11
|H1615
|ADAPTER-90 DEG-#6 JICM X #6 SAEM
|
|
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Cartridges are for replacement only.''
|}

==== <big>''[Current] Lift Circuit Configuration (Pilot-Down Manifold) [July 2003 to Present]''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Current Lift Circuit Configuration (Pilot-Down Manifold) (July 2003 to Present).png|alt=BE-SL & BE-DS Current Lift Circuit Configuration (Pilot-Down Manifold) [July 2003 to Present] |frameless|551x551px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43047002
|MANIFOLD-PILOT DOWN
|
|
|1
|-
|2
|H1501
|ADAPTER-#8 JICM X #6 NPTM
|
|
|2
|-
|3
|H1504
|ADAPTER-#6 JICM X #4 NPTM
|
|
|1
|-
|4
|H1579
|ADAPTER-90 DEG-#6 JICM X #4 NPTM
|
|
|2
|}

==== <big>''[Discontinued] Lift Circuit Configuration (Prior to July 2003)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Lift Circuit Configuration (Prior to July 2003).png|alt=BE-SL & BE-DS Discontinued Lift Circuit Configuration (Prior to July 2003)|frameless|521x521px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|H1501
|ADAPTER-#8 JICM X #6 NPTM
|
|
|1
|-
|2
|H1521
|ADAPTER-# 8 JICSW X #8 SAEM
|
|
|1
|-
|3
|HC0264
|VALVE-CHECK-PILOT TO OPEN
|
|
|1
|-
|4
|H1606
|ADAPTER-90 DEG-#8 JICM X #8 SAEM
|
|
|1
|-
|5
|H1621
|ADAPTER-#4 SAEM X #2 NPTM
|
|
|1
|-
|6
|HC0269
|VALVE-ADJUSTABLE FLOW CONTROL
|
|
|1
|-
|7
|H1591
|ADAPTER-90 DEG-#6 JICM X #2 NPTM
|
|
|1
|-
|8
|H1587
|ADAPTER-#6 JICSW X #4 NPTM
|
|
|1
|}

==== <big>''Lift Circuit Mounting''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL & BE-DS Lift Circuit Mounting.png|alt=BE-SL & BE-DS Lift Circuit Mounting|frameless|550x550px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43017014-2
|SUPPORT-MANIFOLD-PILOT DOWN
|
|
|1
|-
|2
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|2
|-
|3
|43718008
|STANDOFF
|
|
|1
|-
|4
|HW0315
|BOLT-HHCS-1/4-20 X 4 1/2"
|
|
|1
|-
|5
|HW0308
|BOLT-HHCS-1/4-20 X 2 1/2"
|
|
|2
|-
|6
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|10
|-
|7
|HW0103
|WASHER-LOCK-1/4"
|
|
|5
|-
|8
|HW0002
|NUT-HEX-1/4-20
|
|
|5
|}

=== <big>Floor Drive Circuit</big> ===

==== <big>''Cross Port Relief''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL & BE-DS Cross Port Relief.png|alt=BE-SL & BE-DS Cross Port Relief|frameless|554x554px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0262
|VALVE-CROSS PORT RELIEF
|
|
|1
|-
|1a
|43046002
|REPLACEMENT CARTRIDGE
|
|''† For Item 1 (Not shown)''
|A/R
|-
|2
|H1540
|ADAPTER-#8 JICM X #8 SAEM
|
|
|2
|-
|3
|H1646
|ADAPTER-90 DEG-#8 SAEM X #6 FNPT
|
|
|2
|-
|4
|H0805
|TEE-#6 NPTM
|
|
|2
|-
|5
|HC0272
|REGULATOR-FIXED FLOW
|
|''4.0 GPM''
|4
|-
|6
|H1566
|ADAPTER-45 DEG-#8 JICM X #6 NPTM
|
|
|2
|-
|7
|H1501
|ADAPTER-#8 JICM X #6 NPTM
|
|
|2
|-
|8
|HW0308
|BOLT-HHCS-1/4-20 X 2 1/2"
|
|
|2
|-
|9
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|10
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|11
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Cartridges are for replacement only.''
|}

==== <big>''Floor Drive Cutout''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL & BE-DS Floor Drive Cutout.png|alt=BE-SL & BE-DS Floor Drive Cutout|frameless|574x574px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|N/A
|SOLENOID-FLOOR DRIVE CUTOUT
|
|''†'' ''See notes''
|1
|-
|2
|H1540
|ADAPTER-#8 JICM X #8 SAEM
|
|
|1
|-
|3
|H1606
|ADAPTER-90 DEG-#8 JICM X #8 SAEM
|
|
|1
|-
|4
|BI0001
|NIPPLE-CLOSE-#8 NPT
|
|
|1
|-
|5
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|3
|-
|6
|E0611
|JUNCTION BOX-4" X 2" X 2"
|
|
|1
|-
|7
|E0612
|COVER-JUNCTION BOX
|
|
|1
|-
|8
|E0623
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .250" to .375"''
|A/R
|-
|9
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|A/R
|-
|10
|N/A
|SOLENOID-DRIVE CUTOUT
|
|''†'' ''See notes''
|1
|-
|11
|YE0501
|CONNECTOR-SOLENOID
|
|''DIN 43650''
|1
|-
|12
|43058004
|PLATE-SPACER
|
|
|1
|-
|13
|HC0278-SL/DS
|SOLENOID-DRIVE CUTOUT
|
|
|1
|-
|14
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|''For Item 6 (Not shown)''
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Part obsolete. Must be replaced with Retro Kit PT# 80242007.''
|}

==== <big>''Floor Drive Cutout Mounting''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL & BE-DS Floor Drive Cutout Mounting.png|alt=BE-SL & BE-DS Floor Drive Cutout Mounting|frameless|547x547px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HW0305
|BOLT-HHCS-1/4-20 X 2"
|
|
|2
|-
|2
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|3
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|4
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|-
|5
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
|6
|43058004
|PLATE-SPACER
|
|
|1
|}

=== <big>Counter Balance Valve</big> ===

==== <big>''[Discontinued] BE-SL Counter Balance Valve Configuration (Prior to January 2004)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued BE-SL Counter Balance Valve Configuration (Prior to January 2004).png|alt=Discontinued BE-SL Counter Balance Valve Configuration (Prior to January 2004)|frameless|531x531px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0263
|VALVE-COUNTER BALANCE
|
|
|1
|-
|1a
|43046004
|REPLACEMENT CARTRIDGE
|
|''For Item 1 (Not shown)''
|A/R
|-
|2
|H1552
|ADAPTER-#6 JICM X #6 SAEM
|
|
|2
|-
|3
|H1520
|ADAPTER-#6 JICSW X #6 SAEM
|
|
|2
|-
|4
|H1579
|ADAPTER-#6 JICM X #4 NPTM
|
|
|2
|-
|5
|HC0211
|VALVE-ADJUSTABLE FLOW CONTROL
|
|
|2
|-
|6
|H1565
|ADAPTER-45 DEG-#6 JICM X #4 NPTM
|
|
|2
|-
|7
|HW0305
|BOLT-HHCS-1/4-20 X 2"
|
|
|1
|-
|8
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|2
|-
|9
|HW0103
|WASHER-LOCK-1/4"
|
|
|1
|-
|10
|HW0002
|NUT-HEX-1/4-20
|
|
|1
|}

==== <big>''[Current] BE-SL Counter Balance Valve Configuration (January 2004 to Present)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Current BE-SL Counter Balance Valve Configuration (January 2004 to Present).png|alt= Current BE-SL Counter Balance Valve Configuration (January 2004 to Present)|frameless|543x543px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0263
|VALVE-COUNTER BALANCE
|
|
|1
|-
|1a
|43046004
|REPLACEMENT CARTRIDGE
|
|''For Item 1 (Not shown)''
|A/R
|-
|2
|H1552
|ADAPTER-#6 JICM X #6 SAEM
|
|
|2
|-
|3
|H1615
|ADAPTER-90 DEG-#6 JICM X #6 SAEM
|
|
|2
|-
|4
|HW0305
|BOLT-HHCS-1/4-20 X 2"
|
|
|2
|-
|5
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|6
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|7
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|}

==== <big>''[Discontinued] BE-DS Counter Balance Valve Configuration (Prior to January 2004)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued BE-DS Counter Balance Valve Configuration (Prior to January 2004).png|alt= Discontinued BE-DS Counter Balance Valve Configuration (Prior to January 2004)|frameless|575x575px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0263
|VALVE-COUNTER BALANCE
|
|
|1
|-
|1a
|43046004
|REPLACEMENT CARTRIDGE
|
|''† For Item 1 (Not shown)''
|A/R
|-
|2
|H1552
|ADAPTER-#6 JICM X #6 SAEM
|
|
|2
|-
|3
|H1520
|ADAPTER-#6 JICSW X #6 SAEM
|
|
|2
|-
|4
|H1579
|ADAPTER-#6 JICM X #4 NPTM
|
|
|2
|-
|5
|HC0211
|VALVE-ADJUSTABLE FLOW CONTROL
|
|
|2
|-
|6
|H1504
|ADAPTER-#6 JICM X #4 NPTM
|
|
|2
|-
|7
|HW0305
|BOLT-HHCS-1/4-20 X 2"
|
|
|2
|-
|8
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|9
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|10
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Cartridges are for replacement only.''
|}

==== <big>''[Current] BE-DS Counter Balance Valve Configuration (January 2004 to Present)''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Current BE-DS Counter Balance Valve Configuration (January 2004 to Present).png|alt=Current BE-DS Counter Balance Valve Configuration (January 2004 to Present)|frameless|569x569px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0263
|VALVE-COUNTER BALANCE
|
|
|1
|-
|1a
|43046004
|REPLACEMENT CARTRIDGE
|
|''† For Item 1 (Not shown)''
|A/R
|-
|2
|H1552
|ADAPTER-#6 JICM X #6 SAEM
|
|
|2
|-
|3
|H1615
|ADAPTER-90 DEG-#6 JICM X #6 SAEM
|
|
|2
|-
|4
|HW0305
|BOLT-HHCS-1/4-20 X 2"
|
|
|2
|-
|5
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|6
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|7
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Cartridges are for replacement only.''
|}
=== <big>Miscellaneous Components</big> ===

==== ''<big>Transition Manifold</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23)Transition Manifolds.png|alt=BE-SL & BE-DS Transition Manifolds|frameless|543x543px]]
{| class="wikitable"
! colspan="6" |CURRENT CONFIGURATION (FRAME #'S 412 TO PRESENT)
|-
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43747002-2
|PLATE-TRANSITION
|
|
|1
|-
|2
|H0023
|NUT-BULKHEAD-#8 JIC
|
|
|4
|-
|3
|H0024
|UNION-BULKHEAD-#8 JICM
|
|
|4
|-
|4
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|2
|-
|5
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|6
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|7
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|}
{| class="wikitable"
! colspan="6" |DISCONTINUED CONFIGURATION (FRAME #'S 411 AND EARLIER)
|-
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43847003
|MANIFOLD-TRAVELING HOSE
|
|
|1
|-
|2
|43717054
|PLATE-MOUNTING
|
|
|1
|-
|3
|H1501
|ADAPTER-#8 JICM X #6 NPTM
|
|
|8
|-
|4
|HW0317
|BOLT-HHCS-1/4-20 X 3 1/2"
|
|
|2
|-
|5
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|6
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|7
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|}

=== <big>Equalization Chain Hose Guard</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Equalization Chain Hose Guard.png|alt=BE-SL & BE-DS Equalization Chain Hose Guard|frameless|622x622px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43017074-2
|GUARD-HOSE-EQ CHAIN
|
|''†'' ''See notes''
|1
|-
|2
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Used on units manufactured after May 2015.''
|}

=== <big>Hydraulic Schematics</big> ===

==== '''<big>''BE-SL& BE-DS Hydraulic Schematic''</big>''' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL & BE-DS Hydraulics Schematic.png|alt=BE-SL & BE-DS Hydraulics Schematic|frameless|900x900px]]

==== '''<big>''BE-DS with Heat Exchanger Hydraulic Schematic''</big>''' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-DS with Heat Exchanger Hydraulic Schematic.png|alt=BE-DS with Heat Exchanger Hydraulics Schematic|frameless|900x900px]]

==== '''<big>''BE-SL& BE-DS Extended Reach Hydraulic Schematic''</big>''' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL & BE-DS Extended Reach Hydraulic Schematic.png|alt= BE-SL & BE-DS Extended Reach Hydraulic Schematic|frameless|875x875px]]

== <big>Standard Available Options</big> ==

=== <big>Powered Roller Cutout (PRC)</big> ===

==== ''<big>Powered Roller Cutout Photo Eye Locations (Prior to August 2022)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Powered Roller Cutout Photo Eye Locations (Prior to August 2022).png|alt=BE-SL & BE-DS Powered Roller Cutout Photo Eye Locations (Prior to August 2022)|frameless|549x549px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E1321
|PHOTO EYE
|
|
|1
|-
|2
|41235057
|MOUNT-PHOTO EYE
|
|
|1
|-
|3
|HW0216
|SCREW-HHSC-#10-24 X 2"
|
|
|2
|-
|4
|HW0102
|WASHER-FLAT-#10-SAE
|
|
|2
|-
|5
|HW0032
|NUT-NILN-#10-24
|
|
|2
|-
|6
|HW0405
|BOLT-HHCS-3/8-16 X 2 "
|
|
|2
|-
|7
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|4
|-
|8
|HW0107
|WASHER-LOCK-3/8"
|
|
|2
|-
|9
|HW0005
|NUT-HEX-3/8-16
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''Quantities provided are for single-sided (PRC-1) Powered Roller Cutout option. For units with Double Sided (PRC-2) option, quantities are double.''
|-
| colspan="6" |''Configuration shown valid for units sold from November 2004 to Present. Consult the factory for units sold prior to November 1, 2004.''
|}

==== ''<big>Powered Roller Cutout Reflector Locations (Prior to August 2022)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Powered Roller Cutout Reflector Locations (Prior to August 2022).png|alt=BE-SL & BE-DS Powered Roller Cutout Reflector Locations (Prior to August 2022)|frameless|548x548px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E1321R
|REFLECTOR
|
|
|1
|-
|2
|41237013
|MOUNT-REFLECTOR
|
|
|1
|-
|3
|SS0803
|SCREW-RHMS-#6-32 X 5/8"
|
|
|2
|-
|4
|HW0405
|BOLT-HHCS-3/8-16 X 2 "
|
|
|2
|-
|5
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|
|4
|-
|6
|HW0107
|WASHER-LOCK-3/8"
|
|
|2
|-
|7
|HW0005
|NUT-HEX-3/8-16
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''Quantities provided are for single-sided (PRC-1) Powered Roller Cutout option. For units with Double Sided (PRC-2) option, quantities are double.''
|-
| colspan="6" |''Configuration shown valid for units sold from November 2004 to Present. Consult the factory for units sold prior to November 1, 2004.''
|}

==== ''<big>Powered Roller Cutout Photo Eye & Reflector Locations (August 2022 to Present)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Powered Roller Cutout Photo Eye & Reflector Locations (August 2022 to Present).png|alt=BE-SL & BE-DS Powered Roller Cutout Photo Eye & Reflector Locations (August 2022 to Present)|frameless|554x554px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E1321A
|PHOTO EYE
|
|''†'' ''Polarized''
|1
|-
|2
|41217170-2
|MOUNT-PHOTO EYE
|
|
|1
|-
|3
|HW0216
|SCREW-#10-24 X 2"
|
|''††'' ''See notes''
|2
|-
|4
|HW0032
|NUT-NILN-#10-24
|
|
|2
|-
|5
|E1321-R
|REFLECTOR
|
|
|1
|-
|6
|41217171
|MOUNT-REFLECTOR
|
|
|1
|-
|7
|SS0803
|SCREW-RHMS-#6-32 X 5/8"
|
|''††'' ''See notes''
|2
|-
|8
|HW0306
|BOLT-FHSCS-1/4-20 X 1"
|
|
|4
|-
|9
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|10
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|11
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''Quantities provided are for single-sided (PRC-1) Powered Roller Cutout option. For units with Double Sided (PRC-2) option, quantities are double.''
|-
| colspan="6" |''† Polarized Photo Eye recommneded to prevent potential operational issues with very smooth or shiny battery cases.''
|-
| colspan="6" |''†† Photo Eye & Reflector Mounting Screws are trimmed to length.''
|}

==== ''<big>Powered Roller Cutout Details</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Powered Roller Cutout Details.png|alt=BE-SL & BE-DS Powered Roller Cutout Details|frameless|528x528px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0281
|SOLENOID-POWER ROLLER CUTOUT
|
|
|2
|-
|2
|E0611
|JUNCTION BOX-4" X 2" X 2"
|
|
|1
|-
|3
|E0612
|COVER-JUNCTION BOX
|
|
|1
|-
|4
|BI0001
|NIPPLE-CLOSE-#8 NPT
|
|
|2
|-
|5
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|3
|-
|6
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|1
|-
|7
|H1600
|ADAPTER-90 DEG-#6 JICM X #8 SAEM
|
|
|3
|-
|8
|H1546
|ADAPTER-#6 JICM X #8 SAEM
|
|
|1
|-
|9
|41217089
|PLATE-MOUNTING-SOLENOID
|
|
|1
|-
|10
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|2
|-
|11
|HW0308
|BOLT-HHCS-1/4-20 X 2 1/2"
|
|
|2
|-
|12
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|13
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|14
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|15
|HW0143
|WASHER-FLAT-1/4"-FENDER
|
|''Used as Shims (Not shown)''
|A/R
|-
! colspan="6" |NOTES
|-
| colspan="6" |''Option configuration shown valid for units sold from November 2004 to Present. Consult the factory for units sold prior to November 1, 2004.''
|}

==== ''<big>Powered Roller Cutout Override Button</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Powered Roller Cutout Override Button.png|alt=BE-SL & BE-DS Powered Roller Cutout Override Button|frameless|579x579px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|N/A
|ACTUATOR-PUSH BUTTON (DISCONTINUED)
|
|''†'' ''See notes''
|1
|-
|2
|N/A
|CONTACT BLOCK-N/C (DISCONTINUED)
|
|''†'' ''See notes''
|1
|-
|3
|E0384
|ACTUATOR-PUSH BUTTON
|80932002
|
|1
|-
|4
|E0386
|CONTACT BLOCK-N/C
|80932002
|
|1
|-
|5
|E0387
|DUMMY BLOCK
|80932002
|
|1
|-
|6
|E0388
|PUSH BUTTON-GREEN
|80932002
|
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''Button location on dash may vary from position shown.''
|-
| colspan="6" |''† Parts no longer available. Must order new Push-Button Switch Kit 80932002.''
|}

==== ''<big>Powered Roller Cutout Junction Box</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Powered Roller Cutout Junction Box.png|alt=BE-SL & BE-DS Powered Roller Cutout Junction Box|frameless|527x527px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0611
|JUNCTION BOX-4" X 2" X 2"
|
|
|1
|-
|2
|E0612
|COVER-JUNCTION BOX
|
|
|1
|-
|3
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|3
|-
|4
|E0623
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .250" to .375"''
|1
|-
|5
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|4
|-
|6
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''Option configuration shown valid for units sold from November 2004 to Present. Consult the factory for units sold prior to November 1, 2004.''
|}

==== ''<big>Powered Roller Cutout Electrical Schematic</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Powered Roller Cutout Electrical Schematic.png|alt=BE-SL & BE-DS Powered Roller Cutout Electrical Schematic|frameless|900x900px]]

=== <big>Strobe Light & Audible Alarm</big> ===

==== <big>''Discontinued Strobe Light & Stanchion Configuration''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Strobe Light & Stanchion Configuration.png|alt=BE-SL & BE-DS Discontinued Strobe Light and Stanchion Configuration|frameless|770x770px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0317
|LIGHT-STROBE
|
|''110VAC''
|1
|-
|2
|41215014
|STANCHION-STROBE LIGHT
|
|
|1
|-
|3
|HW0402
|BOLT-HHCS-3/8-16 X 1
|
|
|3
|-
|4
|HW0107
|WASHER-LOCK-3/8
|
|
|3
|-
|5
|HW0108
|WASHER-FLAT-3/8-SAE
|
|
|3
|-
|6
|E1010
|CONNECTOR
|
|''Female (Not shown)''
|1
|-
|7
|E1011
|PLUG
|
|''Male (Not shown)''
|1
|}

==== <big>''Discontinued Audible Alarm Configuration''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Audible Alarm Configuration.png|alt=BE-SL & BE-DS Discontinued Audible Alarm Configuration|frameless|541x541px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0317-A
|ALARM-AUDIBLE
|
|
|1
|-
|2
|E0654
|JUNCTION BOX-4" X 4" X 2"
|
|
|1
|-
|3
|00117101-2
|MOUNT-AUDIBLE ALARM
|
|
|1
|-
|4
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|1
|-
|5
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|1
|-
|6
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|4
|}

==== <big>''Current Stack Light Strobe & Alarm Configuration''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Current Stack Light & Alarm Configuration.png|alt=BE-SL & BE-DS Current Stack Light & Alarm Configuration|frameless|860x860px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0362
|MOUNTING BASE
|
|''Includes restraints''
|1
|-
|2
|E0365
|TERMINAL BASE
|
|
|1
|-
|3
|E0363
|STROBE LIGHT-AMBER-120VAC
|
|''† See notes''
|1
|-
|4
|E0364
|AUDIBLE ALARM
|
|''††'' ''See notes''
|1
|-
|5
|SS0118
|SCREW-SHCS-#8-32 X 1"
|
|
|2
|-
|6
|SS0303
|WASHER-FLAT-#8
|
|
|2
|-
|7
|SS0203
|NUT-NILN-#8-32
|
|
|2
|-
|8
|E1010
|RECEPTACLE-TWIST LOCK
|
|''(Not shown)''
|1
|-
|9
|E1011
|PLUG-TWIST LOCK
|
|''(Not shown)''
|1
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† For units equipped with the Audible Alarm option, a cap (Not shown) mounts on top of the Strobe Light in place of the Audible Alarm. Cap included with base.''

''†† For units equipped with the Strobe Light option, the Audible Alarm mounts directly to the terminal base in place of the Strobe Light.''
|}

==== <big>''Stack Light Strobe & Alarm Stanchion Mounting''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) Stack Light Strobe & Alarm Stanchion Mounting.png|alt=BE-SL & BE-DS Stack Light Strobe & Alarm Stanchion Mounting|frameless|517x517px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41235060
|STACK LIGHT STANCHION
|
|''Discontinued''
|A/R
|-
|2
|HW0401
|BOLT-HHCS-3/8-16 X 1"
|
|
|3
|-
|3
|HW0107
|WASHER-LOCK-3/8"
|
|
|3
|-
|4
|HW0108
|WASHER-FLAT-3/8"
|
|
|3
|-
|REF
|43032006
|STANCHION ASSEMBLY
|
|''Includes Items 5 through 8''
|A/R
|-
|5
|43035003
|STACK LIGHT STANCHION
|
|
|1
|-
|6
|43037007-2
|CLAMP BRACKET
|
|
|1
|-
|7
|HW0305
|BOLT-HHCS-1/4-20 X 2"
|
|
|4
|-
|8
|HW0050
|NUT-FLANGED-1/4-20
|
|
|4
|-
|9
|43037004-2
|MOUNTING BRACKET
|
|''Overhead Guard only''
|1
|-
|10
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|}

=== <big>'''Horn'''</big> ===

==== ''<big>BE-SL Horn</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL Horn.png|alt=BE-SL Horn|frameless|543x543px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|YE0308
|BUTTON-HORN
|
|
|1
|-
|2
|E0317-A
|AUDIBLE ALARM
|
|
|1
|-
|3
|E0654
|JUNCTION BOX-4" X 4" X 2"
|
|
|1
|-
|4
|HW0302
|BOLT-HHCS-1/4-20 X 3/4"
|
|
|2
|-
|5
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|2
|-
|6
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|7
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|-
|8
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|1
|-
|9
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|1
|}

==== ''<big>BE-DS Horn</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-DS Horn.png|alt=BE-DS Horn|frameless|561x561px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|YE0308
|BUTTON-HORN
|
|
|1
|-
|2
|E0317-A
|AUDIBLE ALARM
|
|
|1
|-
|3
|E0654
|JUNCTION BOX-4" X 4" X 2"
|
|
|1
|-
|4
|HW0302
|BOLT-HHCS-1/4-20 X 3/4"
|
|
|2
|-
|5
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|2
|-
|6
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|7
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|-
|8
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|1
|-
|9
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|1
|}

=== <big>'''Overhead Guard'''</big> ===
[[File:IOP-400 BE-SL&DS (10-23) BE-DS Overhead Guard.png|alt=BE-SL & BE-DS Overhead Guard|frameless|570x570px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43715017
|OVERHEAD GUARD
|
|
|1
|-
|2
|HW0406
|BOLT-HHCS-3/8-16 X 2 1/2"
|
|
|4
|-
|3
|HW0108
|WASHER-FLAT-3/8"
|
|
|8
|-
|4
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|5
|HW0005
|NUT-HEX-3/8-16
|
|
|4
|}

=== <big>'''Operator Shield'''</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Operator Shield.png|alt=BE-SL & BE-DS Operator Shield|frameless|561x561px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43717116
|SHIELD-OPERATOR
|
|''†'' ''See notes''
|1
|-
|2
|43015010
|FRAME-OPERATOR SHIELD WELDMENT
|
|
|1
|-
|3
|43017066-2
|SUPPORT-SIDE
|
|
|2
|-
|4
|43017065-2
|SUPPORT-LOWER
|
|
|1
|-
|5
|43017067-2
|SUPPORT-UPPER
|
|
|1
|-
|6
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|16
|-
|7
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|32
|-
|8
|HW0103
|WASHER-LOCK-1/4"
|
|
|16
|-
|9
|HW0002
|NUT-HEX-1/4-20
|
|
|16
|-
|10
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|6
|-
! colspan="6" |
|-
| colspan="6" |''† Consult factory for units with Plexiglass bolted directly to frame.''
|}

=== <big>'''High Performance Options'''</big> ===

==== ''<big>Discontinued Outer Frame Guarding (Prior to December 2005)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Outer Frame Guarding.png|alt= BE-SL & BE-DS Discontinued Outer Frame Guarding|frameless|557x557px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41217010-2
|GUARD-FAR END-UPPER
|
|
|1
|-
|2
|41217036-2
|GUARD-FAR END-LOWER
|
|
|1
|-
|3
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|22
|}

==== ''<big>Discontinued Inner Frame Guarding (Prior to December 2005)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Inner Frame Guarding.png|alt=BE-SL & BE-DS Discontinued Inner Frame Guarding |frameless|564x564px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41217014-2
|GUARD-FRONT-OPERATOR CONSOLE
|
|
|1
|-
|2
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|4
|}

==== ''<big>Discontinued Cylinder Clamp Configuration (Prior to December 2005)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Cylinder Clamp Configuration.png|alt=BE-SL & BE-DS Discontinued Cylinder Clamp Configuration|frameless|530x530px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|00158001-22
|CHAIN-ROLLER-#80
|
|
|4
|-
|2
|3033T16
|CLAMP-CYLINDER
|
|
|4
|-
|3
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|4
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|5
|HW0143
|WASHER-FLAT-1/4"-FENDER
|
|
|12
|-
|6
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|7
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† See BE-DS Lift Cylinder Connections section for connecting links and mounting studs.''
|}

==== ''<big>Discontinued Lift Cylinder Configuration (Prior to December 2005)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Lift Cylinder Configuration.png|alt=BE-SL & BE-DS Discontinued Lift Cylinder Configuration|frameless|572x572px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43822006
|CLEVIS ASSEMBLY
|
|''Sold as Assembly only''
|4
|-
|2
|HW0813
|SCREW-SHSS-3/8-16 X 1/2"
|
|''Nylon tipped''
|8
|-
|3
|HC0427
|CYLINDER-LIFT
|
|
|4
|-
|4
|H1615
|ADAPTER-90 DEG-#6 JICM X #6 SAEM
|
|
|4
|-
|5
|HC0426-1
|VELOCITY FUSE
|
|
|4
|-
|6
|H0302
|ELBOW-STR-90 DEG-#6 NPT
|
|
|4
|}

==== ''<big>Current Lift Cylinder Configuration (December 2005 to Present)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Current Lift Cylinder Configuration.png|alt=BE-SL & BE-DS Current Lift Cylinder Configuration|frameless|734x734px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43722001
|CLEVIS ASSEMBLY
|
|''Sold as Assembly only''
|4
|-
|2
|HW0407
|BOLT-HHCS-3/8-16 X 2 3/4"
|
|
|4
|-
|3
|HC0404
|CYLINDER-LIFT
|
|''BS-DS-HP units only''
|4
|-
|4
|H1578
|ADAPTER-90 DEG-#6 JICM X #6 NPTM
|
|
|4
|-
|5
|HC0425
|VELOCITY FUSE
|
|
|4
|-
|6
|H0307
|ADAPTER-90 DEG-#6 NPTM X #8 FNPT
|
|
|4
|-
|7
|HW0107
|WASHER-LOCK-3/8"
|
|
|4
|-
|8
|HW0005
|NUT-HEX-3/8-16
|
|
|4
|}

==== ''<big>Discontinued Floor Drive Assembly (Prior to December 2005)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Floor Drive Assembly.png|alt=BE-SL & BE-DS Discontinued Floor Drive Assembly|frameless|551x551px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|REF
|43722003
|H.P. DRIVE WHEEL ASSEMBLY
|
|
|2
|-
|1
|HC0130
|MOTOR-HYDRAULIC-125CC
|
|
|2
|-
|2
|HW1071
|KEY-WOODRUFF-#808 STANDARD
|
|''Included with Item 1''
|A/R
|}

==== ''<big>Discontinued Pump & Motor Configuration (Prior to December 2005)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued High Performance Pump and Motor Configuration.png|alt=BE-SL & BE-DS Discontinued High Performance Pump and Motor Configuration|frameless|549x549px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0012
|MOTOR-ELECTRIC-7 1/2 HP
|
|
|1
|-
|2
|HC0332
|ADAPTER
|
|''Pump-to-Motor''
|1
|-
|3
|HC0327
|COUPLING-BODY-1 3/8"
|
|''Motor end''
|1
|-
|4
|HC0329
|SPIDER-COUPLING INSERT
|
|
|1
|-
|5
|HC0333
|COUPLING BODY-3/4"
|
|''Pump end''
|1
|-
|6
|HC0277
|SNUBBER-PRESSURE
|
|
|1
|-
|7
|E0613
|RESTRAINT-3/4"
|
|''Grip size .500" to .625"''
|1
|-
|8
|E0618
|LOCKNUT-CONDUIT-3/4"
|
|''(Not shown)''
|1
|}

==== ''<big>Current Pump & Motor Configuration (December 2005 to Present)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Current High Performance Pump and Motor Configuration.png|alt=BE-SL & BE-DS Current High Performance Pump and Motor Configuration|frameless|556x556px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0012
|MOTOR-ELECTRIC-7 1/2 HP
|
|
|1
|-
|2
|HC0326
|ADAPTER
|
|''Pump-to-Motor''
|1
|-
|3
|HC0355
|PUMP-VARIABLE DISPLACEMENT-12 GPM
|
|''Vane type''
|1
|-
|4
|HC0327
|COUPLING BODY-1 3/8"
|
|''Motor end''
|1
|-
|5
|HC0329
|SPIDER-COUPLING INSERT
|
|
|1
|-
|6
|HC0328
|COUPLING BODY-7/8"
|
|''Pump end''
|1
|-
|7
|HW0502
|BOLT-HHCS-1/2-13 X 1 1/4"
|
|
|2
|-
|8
|HW0110
|WASHER-LOCK-1/2"
|
|
|2
|-
|9
|HW0112
|WASHER-FLAT-1/2"-SAE
|
|
|2
|-
|10
|H1606
|ADAPTER-90 DEG-#8 JICM X #8 SAEM
|
|
|1
|-
|11
|H1549
|ADAPTER-#20 JICM X #24 SAEM
|
|
|1
|-
|12
|H1595
|ADAPTER-90 DEG-#20 JICM X 20 JICSW
|
|
|1
|-
|13
|H1609
|ADAPTER-90 DEG-#12 JICM X #16 SAEM
|
|
|1
|-
|14
|E0613
|RESTRAINT-3/4"
|
|''Grip size .500" to .625"''
|1
|-
|15
|E0618
|LOCKNUT-CONDUIT-3/4"
|
|''(Not shown)''
|1
|}

==== ''<big>Current Relief Valve Configuration (December 2005 to Present)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Current Relief Valve Configuration.png|alt=BE-SL & BE-DS Current Relief Valve Configuration|frameless|543x543px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0260
|VALVE-MAIN SYSTEM RELIEF
|
|
|1
|-
|2
|HC0318
|GAUGE-PRESSURE
|
|''0-3000 LBS''
|1
|-
|3
|H1542
|ADAPTER-#12 JICM X #12 SAEM
|
|
|2
|-
|4
|H1650
|ADAPTER-#12 SAEM X #8 SAEF
|
|
|1
|-
|5
|H1606
|ADAPTER-90 DEG-#8 JICM X #8 SAEM
|
|
|1
|-
|6
|H0206
|PLUG-#4 NPT
|
|
|1
|-
|7
|43747003-2
|BRACKET-MOUNTING-RELIEF VALVE
|
|
|1
|-
|8
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|2
|-
|9
|HW0302
|BOLT-HHCS-1/4-20 X 3/4"
|
|
|2
|-
|10
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|6
|-
|11
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|}

==== ''<big>Discontinued Oil Cooler Configuration (Prior to December 2005)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Oil Cooler Configuration.png|alt=BE-SL & BE-DS Discontinued Oil Cooler Configuration|frameless|547x547px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|4
|-
|2
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|8
|-
|3
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|4
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|5
|E0611
|JUNCTION BOX-4" X 2" X 2"
|
|
|1
|-
|6
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
|7
|E0623
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .250" to .375"''
|1
|-
|8
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|2
|-
|9
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|3
|-
|10
|E0612
|COVER-JUNCTION BOX
|
|
|1
|}
[[File:IOP-400 BE-SL&DS (10-23) Discontinued Oil Cooler Configuration 2.png|alt=BE-SL & BE-DS Discontinued Oil Cooler Configuration 2|frameless|550x550px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|4F363
|OIL COOLER
|
|''Includes mounting hardware''
|1
|-
|2
|41215017
|MOUNT-OIL COOLER
|
|
|1
|-
|3
|BI0107
|ELBOW-STR-90 DEG-#12 NPT
|
|
|4
|-
|4
|H1509
|ADAPTER-#10 JICM X #12 NPTM
|
|
|2
|-
|5
|4WT44
|FAN
|
|
|2
|-
|6
|4YD82
|GRILL-FAN
|
|
|2
|-
|7
|SS0112
|SCREW-SHCS-#8-32 X 5/8"
|
|
|16
|-
|8
|SS0303
|WASHER-FLAT-#8
|
|
|8
|-
|9
|SS0203
|NUT-NILN-#8-32
|
|
|16
|-
|10
|4YD79
|CORD-FAN
|
|''(Not shown)''
|2
|}

==== ''<big>Return Line Manifold</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Return Line Manifold.png|alt=BE-SL & BE-DS Return Line Manifold|frameless|555x555px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|41247001
|MANIFOLD-RETURN LINE
|
|
|1
|-
|2
|HW0308
|BOLT-HHCS-1/4-20 X 2 1/2"
|
|
|2
|-
|3
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|6
|-
|4
|HW0103
|WASHER-LOCK-1/4"
|
|
|4
|-
|5
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|-
|6
|43017009-2
|BRACKET-MOUNTING-MANIFOLD
|
|
|1
|-
|7
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|2
|-
|8
|H1509
|ADAPTER-#10 JICM X #12 NPTM
|
|
|1
|-
|9
|H1501
|ADAPTER-#8 JICM X #6 NPTM
|
|
|2
|-
|10
|H1507
|ADAPTER-#8 JICM X #8 NPTM
|
|
|1
|-
|11
|H0208
|PLUG-#12 NPT
|
|
|1
|}

==== ''<big>Discontinued Pressure Reducing Valve Configuration (Prior to December 2005)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Discontinued High Performance Pressure Releasing Valve.png|alt=BE-SL & BE-DS Discontinued High Performance Pressure Releasing Valve|frameless|541x541px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0276
|VALVE-PRESSURE REDUCING
|
|
|1
|-
|2
|H1610
|ADAPTER-90 DEG-#10 JICM X #10 SAEM
|
|
|1
|-
|3
|H1545
|ADAPTER-#10 JICM X #10 SAEM
|
|
|1
|-
|4
|H1615
|ADAPTER-90 DEG-#6 JICM X #6 SAEM
|
|
|1
|-
|5
|HW0308
|BOLT-HHCS-1/4-20 X 2 1/2"
|
|
|2
|-
|6
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|4
|-
|7
|HW0103
|WASHER-LOCK-1/4"
|
|
|2
|-
|8
|HW0002
|NUT-HEX-1/4-20
|
|
|2
|}

==== ''<big>Current BE-DS-HP Lift Circuit Configuration (December 2005 to Present)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Current BE-DS-HP Circuit Configuration.png|alt= Current BE-DS-HP Circuit Configuration|frameless|549x549px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|HC0215
|VALVE-CHECK-CARTRIDGE
|
|
|8
|-
|2
|H1560
|ADAPTER-45 DEG-#8 JICM X #8 SAEM
|
|
|4
|-
|3
|H1108
|ADAPTER-#12 JICM X #10 SAEM
|
|
|1
|-
|4
|H1647
|ADAPTER-90 DEG-#10 SAEM X #8 FNPT
|
|
|1
|-
|5
|H0007
|NIPPLE-# 8 NPT
|
|
|1
|-
|6
|HC0270
|VALVE-ADJUSTABLE FLOW CONTROL
|
|''Pressure compensated''
|1
|-
|7
|H1680
|ADAPTER-#10 JICM X #8 NPTM
|
|
|1
|-
|8
|H1690
|ADAPTER-#10 JICSW X #10 SAEM
|
|
|1
|-
|9
|H1612
|ADAPTER-90 DEG-#8 JICM X #10 SAEM
|
|
|1
|-
|10
|HC0283
|VALVE-COUNTER BALANCE
|
|
|1
|-
|11
|H1552
|ADAPTER-#6 JICM X #6 SAEM
|
|
|1
|-
|12
|H1504
|ADAPTER-#6 JICM X #4 NPTM
|
|
|1
|-
|13
|H1501
|ADAPTER-#8 JICM X #6 NPTM
|
|
|2
|-
|14
|43047002
|MANIFOLD-PILOT DOWN
|
|
|1
|-
|15
|H1579
|ADAPTER-90 DEG-#6 JICM X 4 NPTM
|
|
|2
|-
|16
|N/A
|HOSE-HYDRAULIC-1/4" X 24"
|
|''(Not shown)''
|1
|}

==== ''<big>Magnetic Starter Assembly</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) High Performance Magnetic Starter Assembly.png|alt=BE-SL & BE-DS High Performance Magnetic Starter Assembly|frameless|555x555px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0103-1
|MAGNETIC STARTER
|
|''NEMA 1''
|1
|-
|2
|E0608-1
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .450" to .560"''
|1
|-
|3
|E0623
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .250" to .375"''
|4
|-
|4
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|1
|-
|5
|E0622
|RESTRAINT-1/2"
|
|''Grip size .450" to .560"''
|1
|-
|6
|E0613
|RESTRAINT-3/4"
|
|''Grip size .500" to .625"''
|1
|-
|7
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|7
|-
|8
|E0618
|LOCKNUT-CONDUIT-3/4"
|
|
|1
|-
|9
|HW0303
|BOLT-HHCS-1/4-20 X 1"
|
|
|3
|-
|10
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|7
|-
|11
|HW0103
|WASHER-LOCK-1/4"
|
|
|3
|-
|12
|HW0002
|NUT-HEX-1/4-20
|
|
|4
|}

=== <big>Water Cart</big> ===
[[File:IOP-400 BE-SL&DS (10-23) Water Cart 1.png|alt=BE-SL & BE-DS Water Cart 1|frameless|546x546px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|PB0033
|OVERFILL INDICATOR
|
|
|1
|-
|2
|PB0034
|LOCKNUT-CONDUIT-2"-NYLON
|
|
|1
|-
|3
|HC0308
|FILLER/BREATHER ASSEMBLY
|
|''Includes gaskets''
|1
|-
|4
|HW0209
|SCREW-RHMS-10-32 X 1/2"
|
|
|6
|-
|5
|550-057
|HOSE-FILL-3/4" X 15'
|
|
|1
|-
|6
|550-027
|ON/OFF VALVE
|
|''(Not shown)''
|1
|-
|7
|PB0902
|HOSE-3/4"
|
|
|30"
|-
|8
|HW1018
|HOSE CLAMP-3/4"
|
|
|1
|-
|9
|PB0603
|ADAPTER-3/4" NPT X 3/4" BARB
|
|
|1
|-
|10
|PB0456
|ELBOW-STR-90 DEG-3/4" NPT
|
|
|1
|-
|11
|PB0451
|ADAPTER-3/4" NPT X 3/4 GHT
|
|
|1
|-
|12
|PB0302
|PLUG-3/4" NPT
|
|
|
|-
|13
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|2
|-
|14
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|2
|-
|15
|SS0106
|SHCS-#10-24 X 1/2"-SST
|
|
|6
|-
|16
|SS0114
|BHSCS-#10-24 X 1/2" SST
|
|
|4
|-
|17
|SS0301
|WASHER-FLAT-#10-SAE-SST
|
|
|10
|-
|18
|00196701
|DECAL-BHS-12"
|
|
|1
|-
|19
|00196404
|LABEL-DANGER-"120 VOLTS"
|
|
|1
|-
|20
|00166648
|LABEL, NON-POTABLE
|
|
|1
|-
|21
|HW0418
|BOLT-HHCS-3/8-16 X 2-1/4"
|
| rowspan="3" |''Mounting Hardware''

''(Not shown)''
|2
|-
|22
|HW0031
|NUT-HEX-3/8-16 CENTERLOCK
|
|4
|-
|23
|HW0108
|WASHER-FLAT-3/8"-SAE
|
|2
|}
[[File:IOP-400 BE-SL&DS (10-23) Water Cart 2.png|alt=BE-SL & BE-DS Water Cart 2|frameless|549x549px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|PB0150
|PUMP-SUBMERSIBLE
|
|''† See notes''
|1
|-
|2
|HW1018
|HOSE CLAMP-3/4"
|
|
|1
|-
|3
|46932005
|LEVEL SWITCH CONDUIT ASSEMBLY
|
|''Includes (2) Item #4 and Wiring''
|1
|-
|4
|E1381
|SWITCH-LIQUID LEVEL
|
|
|2
|-
|5
|SS0760
|HOSE CLAMP-4" TO 7"
|
|
|1
|-
|6
|HW1019
|HOSE CLAMP-1"
|
|
|2
|-
|7
|SS06010
|HANDLE
|
|
|2
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Hose Barb Fitting modified at factory during assembly to remove threaded portion from Hose Barb end. Modification of Fitting required prior to installing Replacement Pump.''
|}
[[File:IOP-400 BE-SL&DS (10-23) Water Cart 3.png|alt=BE-SL & BE-DS Water Cart 3|frameless|553x553px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E1511
|SWITCH-ROCKER
|
|''Submersible rated''
|1
|-
|2
|E0378
|INDICATOR LIGHT-120VAC-GREEN
|
|''† See notes''
|1
|-
|3
|E0376
|INDICATOR LIGHT-120VAC-AMBER
|
|''† See notes''
|1
|-
|4
|E0377
|INDICATOR LIGHT-120VAC-RED
|
|''† See notes''
|1
|-
|5
|46917015
|PLACARD-INDICATOR LIGHT
|
|
|1
|-
|6
|E0505
|16-3 SO CORD
|
|
|72"
|-
|7
|E0653
|PLUG-120V/15A
|
|
|1
|-
|8
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|1
|-
|9
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|1
|-
|10
|PL0501
|GROMMET-1/2"
|
|
|2
|-
|11
|E1313
|SOCKET-RELAY-8 PIN
|
|
|1
|-
|12
|E0331
|RELAY-DPDT-110VAC
|
|
|1
|-
|13
|E0440
|TERMINAL BLOCK-8 POLE
|
|
|1
|-
|14
|E1070
|GROUND BAR-4 POSITION
|
|
|1
|-
|15
|HW0139
|SCREW-RHMS-#8-32 X 1 1/4"
|
|
|2
|-
|16
|HW0135
|SCREW-RHMS-#8-32 X 3/4"
|
|
|2
|-
|17
|HW1061
|SCREW-RHMS-#8-32 X 1"
|
|
|1
|-
|18
|HW0132
|NUT-NILN-#8-32
|
|
|5
|-
! colspan="6" |NOTES
|-
| colspan="6" |''† Water carts built prior to October 2021 used Multi-Piece Indicator Lights with replaceable bulb and lens are no longer available. Current Indicator Lights are 1-Piece LED Assembly. Replacement of any Multi-Piece Component requires replacing entire assembly with current, 1 -Piece Indicator Light.''
|}

=== <big>Level Assist (LAI)</big> ===

==== <big>''BE-SL Level Assist''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL Level Assist.png|alt=BE-SL Level Assist|frameless|564x564px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E1321A
|PHOTO EYE
|
|
|1
|-
|2
|HW0216
|SCREW-#10-24 X 2"
|
|''†'' ''See notes''
|2
|-
|3
|HW0032
|NUT-NILN-#10-24
|
|
|2
|-
|4
|43617046
|TARGET-PHOTO EYE
|
|
|1
|-
|5
|HW0302
|BOLT-HHCS-1/4-20 X 3/4"
|
|
|1
|-
|6
|HW0104
|WASHER-FLAT-1/4"-SAE
|
|
|1
|-
|7
|HW0103
|WASHER-LOCK-1/4"
|
|
|1
|-
|8
|HW0002
|NUT-HEX-1/4-20
|
|
|1
|-
|9
|E0376
|INDICATOR LIGHT
|
|''††'' ''See notes''
|1
|-
|10
|HW0152
|WASHER-5/8" I.D.
|
|''†††'' ''For Item 9 (Not shown)''
|2
|-
|11
|E1321-RT
|REFLECTIVE TAPE
|
|''(Not shown)''
|A/R
|-
! colspan="6" |NOTES
|-
| colspan="6" |''Location of Indicator Light on the dash may vary from location shown.''
|-
| colspan="6" |''†'' ''Photo Eye & Reflector Mounting screws are trimmed to length.''
|-
| colspan="6" |''††'' ''Extractors built prior to October 2021 used Multi-Piece Indicator Lights with Replaceable Bulb and Lens are no longer available. Current Indicator Light is a 1-Piece LED Assembly. Replacement of any Multi-Piece Component requires replacing entire assembly with current, 1-Piece Indicator Light.''
|-
| colspan="6" |''†††'' ''Washers required for units that did not ship with Level Assist option from the factory.''
|}

==== <big>''BE-DS Level Assist''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-DS Level Assist.png|alt=BE-DS Level Assist|frameless|558x558px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E1321A
|PHOTO EYE
|
|
|1
|-
|2
|13537001-2
|MOUNT-PHOTO EYE
|
|
|1
|-
|3
|PL0502
|GROMMET
|
|
|1
|-
|4
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|
|2
|-
|5
|E0376
|INDICATOR LIGHT-120VAC-AMBER
|
|''†'' ''See notes''
|1
|-
|6
|HW0152
|WASHER-5/8" I.D.
|
|''††'' ''For Item 5 (Not shown)''
|2
|-
|7
|E1321-RT
|REFLECTIVE TAPE
|
|''(Not shown)''
|A/R
|-
! colspan="6" |NOTES
|-
| colspan="6" |''Location of Indicator Light on the dash may vary from location shown.''
|-
| colspan="6" |''††'' ''Extractors built prior to October 2021 used Multi-Piece Indicator Lights with Replaceable Bulb and Lens are no longer available. Current Indicator Light is a 1-Piece LED Assembly. Replacement of any Multi-Piece Component requires replacing entire assembly with current, 1-Piece Indicator Light.''
|-
| colspan="6" |''†††'' ''Washers required for units that did not ship with Level Assist option from the factory.''
|}

==== <big>''Level Assist Junction Box Mounting''</big> ====
[[File:IOP-400 BE-SL&DS (10-23) BE-DS Level Assist Junction Box.png|alt= BE-DS Level Assist Junction Box|frameless|569x569px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|E0611
|JUNCTION BOX-4" X 2" X 2"
|
|
|1
|-
|2
|E0612
|COVER-JUNCTION BOX
|
|
|1
|-
|3
|E0623
|RESTRAINT-1/2"-90 DEG
|
|''Grip size .250" to .375"''
|2
|-
|4
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|1
|-
|5
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|3
|-
|6
|HW0301
|BOLT-SELF TAP "F"-1/4-20 X 1/2"
|
|''Mounting Bolts (Not shown)''
|2
|}

=== <big>Blue Light (BE-BLU-LT)</big> ===

==== ''<big>BE-SL Blue Light</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-SL Blue Light.png|alt=BE-SL Blue Light|frameless|548x548px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43735004
|STANCHION-MOUNTING
|
|''Includes Junction Box''
|1
|-
|2
|EW2002B
|BLUE PROJECTION SPOTLIGHT
|
|
|2
|-
|3
|E0612
|COVER-JUNCTION BOX
|
|
|1
|-
|4
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|2
|-
|5
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|2
|-
|6
|HW0321
|BOLT-HHCS-5/16-18 X 1 1/4"
|
|
|2
|-
|7
|HW0106
|WASHER-FLAT-5/16"-SAE
|
|
|4
|-
|8
|HW0105
|WASHER-LOCK-5/16"
|
|
|2
|-
|9
|HW0004
|NUT-HEX-5/16-18
|
|
|2
|-
|REF
|43032006
|STANCHION ASSEMBLY
|
|''Includes Items 10 through 13''
|A/R
|-
|10
|43035003
|STACK LIGHT STANCHION
|
|
|1
|-
|11
|43037007-2
|CLAMP BRACKET
|
|
|1
|-
|12
|HW0305
|BOLT-HHCS-1/4-20 X 2"
|
|
|4
|-
|13
|HW0050
|NUT-FLANGED-1/4-20
|
|
|4
|-
|14
|E1010
|RECEPTACLE-TWIST LOCK
|
|''(Not shown)''
|2
|-
|15
|E1011
|PLUG-TWIST LOCK
|
|''(Not shown)''
|2
|}

==== ''<big>BE-DS Blue Light</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) BE-DS Blue Light.png|alt=BE-DS Blue Light|frameless|500x500px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|43735004
|STANCHION-MOUNTING
|
|''Includes Junction Box''
|2
|-
|2
|EW2002B
|BLUE PROJECTION SPOTLIGHT
|
|
|2
|-
|3
|E0612
|COVER-JUNCTION BOX
|
|
|2
|-
|4
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|4
|-
|5
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|4
|-
|6
|HW0321
|BOLT-HHCS-5/16-18 X 1 1/4"
|
|
|4
|-
|7
|HW0106
|WASHER-FLAT-5/16"-SAE
|
|
|8
|-
|8
|HW0105
|WASHER-LOCK-5/16"
|
|
|4
|-
|9
|HW0004
|NUT-HEX-5/16-18
|
|
|4
|-
|10
|E1010
|RECEPTACLE-TWIST LOCK
|
|''(Not shown)''
|2
|-
|11
|E1011
|PLUG-TWIST LOCK
|
|''(Not shown)''
|2
|}

==== ''<big>Blue Light Power Supply for Units Without IIoT (Prior to February 2020)</big>'' ====
[[File:IOP-400 BE-SL&DS (10-23) Blue Light Power Supply.png|alt=BE-SL & BE-DS Blue Light Power Supply|frameless|584x584px]]
{| class="wikitable"
!ITEM
!BHS PART NUMBER
!DESCRIPTION
!REF. KIT NO.
!NOTES
!NO. REQ
|-
|1
|N/A
|ENCLOSURE-8" X 8" X 4"
|
|''Consult factory''
|1
|-
|2
|E0135
|PANEL-COMPONENT MOUNTING
|
|''Blank panel without holes''
|1
|-
|3
|PS5R-SC12
|POWER SUPPLY
|
|
|1
|-
|4
|E0908
|MOUNTING RAIL
|
|''Sold by length''
|A/R
|-
|5
|YE0402
|TERMINAL BLOCK
|
|
|4
|-
|6
|YE0405
|END BARRIER
|
|
|1
|-
|7
|YE0406
|END ANCHOR
|
|
|2
|-
|8
|E0341
|GROUND LUG
|
|
|1
|-
|9
|E0616
|RESTRAINT-1/2"
|
|''Grip size .250" to .375"''
|3
|-
|10
|E0617
|LOCKNUT-CONDUIT-1/2"
|
|
|3
|-
|11
|HW0130
|SCREW-RHMS-#8-32 X 1/2"
|
|''2 per Mounting Rail''
|5
|-
|12
|HW0132
|NUT-NILN-#8-32
|
|''2 per Mounting Rail''
|5
|-
|13
|HW0133
|WASHER-FLAT-#8-SAE
|
|''2 per Mounting Rail''
|5
|-
|14
|00196404
|LABEL-DANGER-"120 VOLTS"
|
|
|1
|}

= <big>Service & Maintenance</big> =

== <big>Daily Inspection List</big> ==
The points listed below should be visually inspected daily prior to initial start up of the Battery Extractor to ensure safe and proper operation of the unit and to help avoid unnecessary down time.

# Walk around unit and inspect for any physical damage to machine not previously noted.
# Verify all guards are in place.
# Inspect the AC power feed for any damage.
# Vacuum equipped units: Inspect vacuum cups for damage to cup sealing surface, backup casting, and vacuum hoses. Magnet equipped units: Inspect magnets for damage to attachment face, proximity sensor cover, cables and connections.
# Inspect travel path and area around unit for any hydraulic oil that could be a potential repair/maintenance issue and/or safety hazard.
# Check oil level in hydraulic reservoir at fill level gauge.
# Check that operator safety gate and all safety switches are in proper working order.
# Verify extractor path is free of obstructions.
# Check roller beds for any debris and clean as required.
# Board unit, engage system and verify all functions are operating properly and that no abnormal or unusual noises are present.

<nowiki>*</nowiki>USE FORM IF-5008 WHEN PREFORMING DAILY INSPECTIONS.

== <big>Operator's Daily Checklist</big> ==
[[File:IOP-400 BE-SL&DS (10-23) Operator's Daily Checklist.png|alt=BE-SL & BE-DS Operator's Daily Checklist|frameless|1230x1230px]]

== <big>Recommended Battery Extractor Lubrication Intervals</big> ==
{| class="wikitable"
!Lubrication Task
!'''# of Places'''
!Intervals
|-
|'''1. Lubricate grease fittings using #2 lithium based grease'''
|
|
|-
|A. Extractor arm drive nut and carrier bearings
|5 places
|50 hrs / Weekly
|-
|B. Idler casters
|2 places
|200 hrs / Weekly
|-
|'''2. Wipe off and lubricate chains using light machine oil'''
|
|
|-
|A. #80 Lift chains (Not applicable to BE-SL units)
|4 places
|200 hrs / Monthly
|-
|B. #60 Equalization chains
|4 places
|200 hrs / Monthly
|-
|C. #35 Powered roller chains
|8 places
|200 hrs / Monthly
|-
|'''3. Change return line hydraulic fluid filter'''
''(Oil filtration of at least 20 microns is recommended)''
|1 place
|300 hrs / Twice Quarterly
|-
|'''4. Change hydraulic fluid'''
| -
|600 hrs / Quarterly *
|-
|'''5. Complete preventative maintenance (PM)'''
Use form IF-5029 for Vacuum equipped units.

Use form IF-5028 for Magnet equipped units.
| -
|600 hrs / Quarterly
|-
! colspan="3" |NOTES
|-
| colspan="3" |''These recommendations are based on average use in a typical warehouse environment and may be adjusted based on specific circumstances. Dusty and/or extreme hot/cold environments may require more frequent lubrication.''
|-
| colspan="3" |''* BHS recommends implementing an oil sampling and analysis program to monitor hydraulic fluid condition and determine when hydraulic fluid changes are required. The fluid analysis program should be a continuous process and all results should be evaluated. Changes in the condition of the hydraulic system may indicate component wear, fluid deterioration and/or contamination.''
|}
{|
|[[File:NOTICE-warn.png|alt=NOTICE|frameless|120x120px]]
|
* '''The mounted bearings used on the power rollers, equalization shafts, drive wheels, and drive screw are sealed and shielded bearings. Lubrication may breach the seals of these bearings, therefore these bearings should not be lubricated unless the machine has been cleaned with a high pressure wash on a regular basis (not recommended).'''
* '''Hydraulic fluid should not exceed 140°F (60°C) for extended periods.'''
|}

=== <big>'''Reservoir Capacities ''(APPROX.)'''''</big> ===
{|
|BE-SL
|18 gal (68 L)
|-
|BE-DS
|18 gal (68 L)
|-
| rowspan="2" |BE-TS
|30 gal (114 L) ''(Units built Pre-2014)''
|-
|45 gal (170 L) ''(Units built 2014 to Present)''
|-
|BE-QS
|60 gal (227 L)
|}
The reservoir should be filled so fluid level is within a half inch (1/2") of the top of sight glass. Use Chevron AW 68 or equivalent ISO 68 grade hydraulic oil with anti-wear additives and foam suppressant.

'''''NOTE'':''' Some units shipped from the factory with AW 32 oil for cold environment operation. Units using AW 32 from the factory may experience poor performance if AW 68 is used instead of AW 32 due to the increased viscosity of the oil.

== <big>Preventative Maintenance Reports</big> ==

=== <big>Vacuum Extraction</big> ===
[[File:Battery Extractor Series - Vacuum Extraction Planned Maintenance Inspection Report Page 1.png|alt=Battery Extractor Series - Vacuum Extraction Planned Maintenance Inspection Report Page1|frameless|1238x1238px]]

[[File:Battery Extractor Series - Vacuum Extraction Planned Maintenance Inspection Report page2.png|alt=Battery Extractor Series - Vacuum Extraction Planned Maintenance Inspection Report Page 2|frameless|1230x1230px]]

=== <big>Magnet Extraction</big> ===
[[File:Battery Extractor Series - Magnet Extraction Planned Maintenance Inspection Report Page 1.png|alt= Battery Extractor Series - Magnet Extraction Planned Maintenance Inspection Report Page 1|frameless|1224x1224px]]

[[File:Battery Extractor Series - Magnet Extraction Planned Maintenance Inspection Report Page 2.png|alt= Battery Extractor Series - Magnet Extraction Planned Maintenance Inspection Report Page 2|frameless|1233x1233px]]

== <big>80292002-i – Equalization Chain Installation / Resetting Procedure</big> ==

=== <big>Required Tools</big> ===

* Large standard screwdriver
* 1/8", 5/32", 3/16" Allen wrench
* (2) 1-1/8" Open-end wrenches
* Needle nose pliers
* 6" Steel scale (ruler)
* Brake cleaner (non-chlorinated)
* Loctite #242 (blue)
* 80292002 - E.Q. Adjustment stop kit (SL, DS, TS) or 80492001 - BE-QS E.Q. Adjustment stop kit
* Ladder or work platform ''(see notes)''

=== <big>''Optional Tools''</big> ===

* Wire brush for removing Loctite from components prior to reassembly

=== <big>Notes</big> ===

* ''A ladder, man lift or other device is required to access the upper E.Q. studs on BE-TS and BE-QS units.''
* ''The following procedures must be performed with the extractor unloaded and in a level area of the travel path.''
* ''Installation of the E.Q. stop kit requires (4) persons plus a trained battery extractor operator to raise and lower the inner carriage.''
* ''It is recommended to have new E.Q. chain connecting links on hand prior to performing the following procedures.''
* ''The upper E.Q. stud lock washers cannot be reused and must be replaced prior to reassembly.''

[[File:IOP-400 BE-SL&DS (10-23) Page 369 Image 0001.png|alt=BE-TS with EQ Adjustment Stops Installed|none|thumb|300x300px|BE-TS with EQ Adjustment Stops Installed]]

=== <big>IMPORTANT</big> ===

* '''Read and understand the Safety and De-energization Procedure TP-606 before starting this procedure.'''
* '''Read and understand these instructions completely before starting this procedure.'''

=== <big>Procedure</big> ===
1. Remove the inner and outer frame guards to access the lower equalization studs.

2. Raise the inner frame approximately 30" (762 mm) for SL, DS and TS units or 50" (1270 mm) for QS units from the fully lowered position. Install (1) adjustment stop at each corner of the roller bed. See Figure 1.
[[File:IOP-400 BE-SL&DS (10-23) EQ Chain Instructions-Figure1.png|alt=|none|thumb|375x375px|FIGURE 1]]
3. Slowly lower the inner carriage until the roller bed is firmly and securely seated against all four stops. See Figure 2.
[[File:IOP-400 BE-SL&DS (10-23) Page 370 Image 0002.png|alt=Roller bed firmly seated against all four stops|none|thumb|398x398px|FIGURE 2]]
4. Lockout/tagout the B.E. per your corporate policy.

5. De-energize the B.E. per BHS Safety and De-energization procedure TP-606.

6. Loosen and remove the upper hex nuts and remove the upper chain studs. Remove the lock washers from the upper chain studs. Save the hex nuts for reassembly later. Discard the lock washers and obtain new, 3/4" split-ring lock washers for reassembly.

7. If replacing the chain, remove the upper stud and remove the chain from the lower stud. Discard the connecting links.

* ''If the E.Q. chains are being reset due to a connecting link failure, it is recommended to also replace the stud where the connecting link failed.''
* ''It is recommended to replace the connecting links when replacing or resetting the E.Q. chains.''

8. If replacing a lower stud, remove the connecting link and disconnect the chain. Loosen the hex nut and remove the stud. Remove the hex nut from the old stud and reinstall it on the new stud. Reinstall the new stud so that it is flush with the bottom of the frame and the hole is aligned front-to-back with the extractor.

9. Attach the chains to the lower studs using the connecting links. Attach the upper studs to the chains using the connecting links, making sure the nut is threaded down near the connecting link and lay the chains in the frame. See Figure 3.

* ''Do not fully assemble the lower connecting links by bending the cotter pins as the connecting link may need to be removed later for stud adjustment.''[[File:IOP-400 BE-SL&DS (10-23) EQ Chain Attached to Upper Stud.png|alt=BE-SL & BE-DS EQ Chain Attached to Upper Stud|none|thumb|300x300px|FIGURE 3]]

10. If new E.Q. sprockets are to be installed, remove the clamp collars and old sprockets. Install the new sprockets and reinstall the clamp collars. DO NOT tighten the set screws at this point as adjustment/alignment may be required.

* ''Sprockets MUST be keyed in-line.''

11. Align the E.Q. shafts so that the keyways are in the 2 o'clock position (approximately 60 degrees from vertical). This will bring the sprocket set screws to the top of the sprocket when the inner carriage is lowered. See Figure 4.
[[File:IOP-400 BE-SL&DS (10-23) EQ Shafts aligned 60 Degrees from Vertical.png|alt=BE-SL & BE-DS EQ Shafts aligned 60 Degrees from Vertical|none|thumb|300x300px|FIGURE 4]]
12. Starting with the inside chain, route the chain over the sprocket directly above the lower stud and under the inside sprocket on the opposite shaft. Attach the upper stud to the top cross bar, making sure a new 3/4" split -ring lock washer is installed between the cross bar and lower hex nut. Hand tighten the upper stud adjusting nut to remove slack from the chain. See Figure 5.

13. Route the outer chain over the sprocket, above the stud and under the sprocket on the opposite shaft. Attach the upper stud to the top cross bar, making sure a new, 3/4" split-ring lock washer is installed between the cross bar and lower hex nut. Hand tighten the upper stud adjusting nut to remove slack from the chain. See Figure 5.

* ''It is recommended to begin at the operator end where room is limited allowing easier access at the opposite end to route the chain under the final sprocket.''

[[File:IOP-400 BE-SL&DS (10-23) Inside and Outside EQ Chains.png|alt=BE-SL&DS Inside and Outside EQ Chains|none|thumb|499x499px|FIGURE 5]]
14. Repeat steps 11 through 13 for the opposite side of the extractor. It is likely that a large, standard screwdriver will be necessary to position the final chain over the sprocket. See Figure 6.
[[File:IOP-400 BE-SL&DS (10-23) Page 371 Image 0002.png|alt=It is likely that a large, standard screwdriver will be necessary to position the final chain over the sprocket.|none|thumb|300x300px|FIGURE 6]]
15. Adjust the lower studs up or down as necessary to take the slack out of the chain between the lower studs and the sprockets by removing the connecting link from the stud and turning the stud. Tighten the hex nuts against the frame once the studs have been adjusted. Reattach the chain.

* DO NOT allow the stud to twist when tightening the hex nuts.

16. Tighten the upper hex nut on the upper studs until there is approximately 1/4" (7 mm) of total deflection in the middle of the upper, vertical chain sections. Tighten the lower hex nuts on the upper studs to lock the studs in place.

* ''Each section of chain between the sprockets should have approximately the same tension as the other on the same side. See Figure 5.''

17. Raise the inner frame and remove the adjustment stops from the four corners and lower the inside frame.

18. Verify equalization sprocket and stud alignment by using a 6" scale. Measure the distance from the inside roller bed frame to the center of the equalization stud. Compare this distance with the measurements from the inside roller bed frame to the center-lines of the sprockets. Adjust the position of the sprocket as necessary to make the distances equal. This will ensure the chain and sprockets are in line with the stud. Repeat this process for the three remaining chains. See Figures 7 & 8.

19. Raise and lower the inner frame several times and listen for any chain popping noises to confirm the sprockets are in line with the lower studs. If there is no popping noise, lower the inner frame all the way down.
[[File:IOP-400 BE-SL&DS (10-23) EQ Chain Verify equalization sprocket and stud alignment by using a 6in scale-Fig7.png|alt=BE-SL&DS EQ Chain Procedure FIgure 7 - Verify equalization sprocket and stud alignment by using a 6" scale|none|thumb|300x300px|FIGURE 7]]
[[File:IOP-400 BE-SL&DS (10-23) EQ Chain Verify equalization sprocket and stud alignment by using a 6in scale-Fig8.png|alt=BE-SL & BE-DS EQ Chain Verify equalization sprocket and stud alignment by using a 6in scale - Fig 8|none|thumb|300x300px|FIGURE 8]]
20. Clean any existing, hardened Loctite from the sprockets, sprocket sets screws, clamp collars and clamp collar bolts.

21. Apply Loctite to and tighten the set screws on the sprockets. Slide the clamp collars against the outside sprocket, loctite and tighten the clamp collars.

== <big>80292001-i – Battery Extractor Service Stand Installation Instructions</big> ==

=== <big>Required Tools</big> ===
None

=== <big>Notes</big> ===

* ''Refer to kit part # 80292001 or 80392001 for the complete bill of materials supplied.''
* ''Remove ALL batteries from extractor prior to installation / service.''
* ''Installation of service stands requires (2) persons plus a trained battery extractor operator to raise and lower the inner carriage. DO NOT attempt installation with less than (3) persons.''

[[File:IOP-400 BE-SL&DS (10-23) Single Level Service Stand Properly Installed.png|alt= Single Level Service Stand Properly Installed|none|thumb|368x368px|Single Level Service Stand Properly Installed]]

=== <big>IMPORTANT</big> ===

* '''Read and understand the Safety and De-energization Procedure TP-606 before starting this procedure.'''
* '''Read and understand these instructions completely before starting this procedure.'''

=== <big>Procedure</big> ===
1. Have a qualified operator raise the inner carriage of the extractor to the required height for installation. For single level applications, the required height will be approximately 25" (64 cm) from the fully lowered position. For double, triple, and quad stack machines, the required height will be approximately 55" (140 cm) from the fully lowered position.

* On double, triple, and quad stack battery extractors, the operator either must remain on the operator platform during service or be provided an OSHA approved method of egress. This is not applicable to single level battery extractors as the operator platform height is fixed.

2. Install the stands by engaging the top of the stand into the inner carriage cutouts. Place the bottom channel of the stand over the tube of the outer frame. The top flanges of each stand are tapered to aid in proper alignment of the stand with the inner frame.

See Figures 1 & 2.
[[File:IOP-400 BE-SL&DS (10-23) engaging the top of the stand into the inner carriage cutout.png|alt=Properly seated in cutout|none|thumb|300x300px|FIGURE 1]]
[[File:IOP-400 BE-SL&DS (10-23) Page 374 Image 0005.png|none|thumb|300x300px|FIGURE 2]]
3. Once BOTH stands have been properly placed, SLOWLY lower the inner carriage while the stands are held in place.

4. Once the inner carriage is firmly seated on the service stands, verify the stands are securely installed. See Figure 3.
[[File:IOP-400 BE-SL&DS (10-23) Page 374 Image 0006.png|none|thumb|450x450px|FIGURE 3]]

== <big>Trouble Shooting Guide</big> ==
{| class="wikitable"
!Problem Symptom
!Probable Cause
!Solution
|-
|Hydraulic power Unit does not operate.
No electric to power unit motor.
|1. No AC power to Unit.
2. Reset on magnetic motor starter tripped.

3. Gate switch not actuated.

4. Foot Pedal switch not engaged.

5. Emergency Stop switch is depressed.
|1. Check fuses or breaker.
2. Check reset button.

3. Make sure safety gate is engaging switch.

4. Check foot pedal for obstruction.

5. Reset button using machine key.
|-
|Power unit runs but no pressure reading at gauge,
also no functions move.
|1. AC input is in reverse phase. Motor is running backwards.
2. Main system relief valve stuck open or defective.

3. Coupling between motor and pump loose.
|1. Reverse any two of the three hot lines to unit.
2. Check relief valve cartridge for trash or debris.

Replace as required.

3. Inspect coupling assy.
|-
|Magnetic starter contact chatters-at startup.
Contact chatters while traveling.
|1. 1 leg of 3 phase input power out.
2. Safety gate and/or gate switch out of adjustment.
|1. Check fuse or circuit breaker at service panel.
2. Check and adjust gate or switch as required to

ensure full engagement of plunger on gate

switch and that the safety gate is not bouncing

due to vibration.
|-
|No floor travel empty or loaded-all other functions work properly.
|1. Extractor arm off center-left to right.
2. Proximity switch or sensing bracket out of target range.

3. Proximity switch defective or broken.

4. Bad solenoid coil on floor cutout valve.

5. Spool on floor cutout valve stuck open.
|1. Center arm.
2. Adjust as needed to achieve 1/4” clearance.

3. Check switch and replace.

4. Check solenoid and replace if needed.

5. Remove and clean spool cartridge or replace.
|-
|Floor travel moves but is sluggish
and stalls with a load at certain points.
|1. Uneven floor conditions. High/low spots.
2. Excessive tire wear.

3. Wheel shaft-to-motor shaft coupling on drive wheel assembly loose or broken.

4. Debris lodged under battery extractor.
|1. Check flatness of floor. Check guidance track for scraping of guide arm on top of angle.
2. Measure under clearance of battery extractor. Should be no less than 5/8” replace poly wheels as needed.

3. Inspect drive assembly while under load to see if shafts and couplings are moving in unison. Repair as needed.

4. Inspect under unit and remove debris.
|-
|Inner carriage bounces while lifting under load,
but not when empty.
|1. Down speed adjustment valve open too far.
|1. Adjust as needed to eliminate carriage bounce.
|-
|Inner carriage does not lift evenly.
Four corners do not land evenly against outer frame tube.
|1. Equalization chains are out of adjustment.
2. Excessive chain or sprocket wear.

3. Equalization chains are out of synchronization. Possibly may have jumped a sprocket tooth.

4. Broken bearing housing on mounted shaft.

5. Lift cylinder roping chains out of adjustment.
|1. Readjust with the top stud until equal tension is achieved.
2. Replace as needed.

3. Evaluate and resynchronize as required.

4. Inspect and replace.

5. Readjust as needed to equal tension on all four cylinders in full down position.
|}

= <big>Aftermarket Support</big> =
[https://na.bhs1.com/blog/post/tt-922-technical-support Click here] for details on BHS' Aftermarket Support.

= <big>Statement of Warranty</big> =
[https://store.bhs1.com/warranty Click here] for details on BHS' Statement of Warranty.

IOP-29401001 Lift Table Ladder

2024-01-29T19:34:12Z

Mbowen: /* Statement of Warranty */

IOP-29401001 Lift Table Ladder

2024-01-29T19:33:52Z

Mbowen: /* Statement of Warranty */

IOM-078 WTC

2022-11-18T19:58:01Z

Mbowen: /* STATEMENT OF WARRANTY */

IOSM-240 BLB

2022-11-18T19:39:20Z

Mbowen: /* LOAD CAPACITY STATEMENT MODEL BLB-6000 BATTERY LIFTING BEAM AND BUILT TO STANDARDS */

{{DISPLAYTITLE:{{FULLPAGENAME}}}}'''Looking for a specific replacement part?''' Ctrl-F (or Command-F for Mac users) brings up your browsers search panel and can search any text on the entire web page. Find parts by searching a part# or part description.

'''Register your equipment with [https://na.bhs1.com/media-library/bhs-optima/ BHS Optima], BHS's free app.'''

'''California Residents''': WARNING: This product contains chemicals known to the State of California to cause cancer and/or reproductive harm, and birth defects or other reproductive harm. [https://na.bhs1.com/about-bhs/compliance-statement-for-california-proposition-65/ Learn more here.]

== Battery Lifting Beam (BLB) System Parts & Service Manual ==
===SAFETY ===
[[File:IOSM-240-BLB-(03-06-07)-2.jpg|700px|border]]

=== GENERAL SAFETY PRACTICES WHEN HANDLING SUSPENDED LOADS ===
[[File:IOSM-240-BLB-(03-06-07)-3.jpg|500px|right]]
'''GENERAL SAFETY PRACTICES WHEN HANDLING SUSPENDED LOADS'''

<ol>

<li>Always lock your elbow and stay at least an arm's length away from the load.</li>
<li>Position hand at rear of lifting beam to help guide battery.</li>
<li>Never use your body or limbs to stop a swinging load.</li>
<li>Be sure feet are not under the battery and are out of the primary danger zone.</li>
<li>The operator, as required by your company's safety policy and/or O.S.H.A, '''SHALL''' wear the proper safety equipment.</li>
<li>All lifting apparatus '''SHALL''' be inspected at the beginning of each shift to ensure no damage or defects are present that could pose a safety hazard.</li>
<li>Areas of travel '''SHALL''' be clear of any trip hazards and obstacles.</li>
<li>Only trained and authorized personnel '''SHALL''' operate overhead lifting equipment and this battery below-the- hook device.</li>
<li>The operator '''SHALL''' verity that any load slings or below-the-hook devices are properly secured to the load prior to lifting or moving the load.</li>
<li>No other persons '''SHALL''' be in the work area or travel path of the load or empty below-the-hook device.</li>
<li>The operator '''SHALL NOT''' place hands or fingers on hooks.</li>
<li>The operator '''SHALL NOT''' tilt the below-the-hook device causing the hooks to hang outside the lines of the below-the-hook device.</li>
</ol>

=== BATTERY LIFTING BEAM DAILY INSPECTION ===
[[File:IOSM-240-BLB-(03-06-07)-4.jpg|700px|border]]

'''BATTERY LIFTING BEAM DAILY INSPECTION'''

Inspections are to be performed: " At the beginning of each shift and/or before first use." Using a lifting device that is worn or damaged can cause loss of load and possible per sonal injury or death.
<ol>
<li>Inspect the wood laminate load members for any cracks, splits, indentions, or delamination.</li>
<li>Inspect all attaching hardware for tightness and wear.</li>
<li>Inspect hook adjusting trunnions for wear or damage.</li>
<li>Inspect load pins on battery lift hooks for wear or damage.</li>
<li>Inspect battery hook engaging throat for excessive wear or damage.
::-Minimum throat height - 5/8" at center of throat.</li>
<li>Inspect lift "A" plate for excessive wear.
::-Minimum height - 3/4" at engagement point to hoist.</li>
</ol>
'''If any of the above conditions do not meet wear and/or dimensional specifications, this device should be removed from service and replaced immediately.'''

=== PROPER HOOK ENGAGEMENT OPERATION ===

'''PROPER HOOK ENGAGEMENT OPERATION'''

Lower the lifting beam horizontally until the hooks are slightly above the battery eyelets.

Push the beam forward a few inches to allow the hook farthest from you to pass the outside edge of the battery eyelet.

Lower the beam until the hook inserts into the eyelet.

Push down slightly on the heal of the beam closest to you and lower it until the hook can be inserted into the battery eyelet closest to you .

Lift the beam slightly to engage the hooks completely in the eyelets of the battery.

Insure both hooks are fully engaged in the battery eyelet.

Continue to lift and move battery

=== PROPER HOOK POSITION FOR THE BHS BLB-6000 BATTERY LIFTING BEAM ===
[[File:IOSM-240-BLB-(03-06-07)-6.jpg|500px|none]]
'''PROPER HOOK POSITION FOR THE BHS BLB-6000 BATTERY LIFTING BEAM'''
'''BASIC OPERATION NOTES'''

Make sure hooks are fully engaged in battery lifting eyelet prior to lifting the battery. Hooks '''SHALL''' be fully inserted into the battery holes as shown in Figure #1

Hooks '''SHALL''' be spaced equally around the center line of the below-the-hook device and be properly placed in the scalloped adjusting trunnions. Correct positioning of the hooks will allow the battery to be level when lifted.

Hooks '''SHALL''' be hanging in a vertical position as shown in Figure #1. Do not allow hooks to be tilted inward or outward as in Figures #2 and #3.

=== PRIMARY DANGER ZONES FOR OPERATORS USING BLB-6000 LIFTING BEAM AND GANTRY CRANE ===
[[File:IOSM-240-BLB-(03-06-07)-7.jpg|700px|border]]

=== BLB-6000 ===
[[File:IOSM-240-BLB-(03-06-07)-4.jpg|700px|border]]

'''BLB-6000'''

 

<table style="border-collapse:collapse;margin-left:92.8407pt" cellspacing="0"><tr style="height:19pt"><td style="width:49pt">Item</td><td style="width:133pt">PPart No.</td><td style="width:191pt">Description</td><td style="width:23pt">Qty</td></tr><tr style="height:20pt"><td style="width:49pt">1</td><td style="width:133pt">24016003</td><td style="width:191pt">Wood BLB-6000 Beam</td><td style="width:23pt">2</td></tr><tr style="height:13pt"><td style="width:49pt">2</td><td style="width:133pt">24015001</td><td style="width:191pt">Hook Standard</td><td style="width:23pt">2</td></tr><tr style="height:13pt"><td style="width:49pt">3</td><td style="width:133pt">24016001</td><td style="width:191pt">Lift Plate - Hook</td><td style="width:23pt">1</td></tr><tr style="height:14pt"><td style="width:49pt">4</td><td style="width:133pt">24017002</td><td style="width:191pt">Plate Spanner</td><td style="width:23pt">2</td></tr><tr style="height:15pt"><td style="width:49pt">5</td><td style="width:133pt">24017005</td><td style="width:191pt">Spacer - Block</td><td style="width:23pt">2</td></tr><tr style="height:14pt"><td style="width:49pt">6</td><td style="width:133pt">24096001</td><td style="width:191pt">Trunnion - Aluminum</td><td style="width:23pt">4</td></tr><tr style="height:14pt"><td style="width:49pt">7</td><td style="width:133pt">LB0080</td><td style="width:191pt">Pin - Spring 1/4" x 1 1/2"</td><td style="width:23pt">8</td></tr><tr style="height:14pt"><td style="width:49pt">8</td><td style="width:133pt">LB0060</td><td style="width:191pt">Straps - Tie</td><td style="width:23pt">4</td></tr><tr style="height:14pt"><td style="width:49pt">9</td><td style="width:133pt">LB0090</td><td style="width:191pt">Bolt 1/2 x 5 NCGR5</td><td style="width:23pt">5</td></tr><tr style="height:13pt"><td style="width:49pt">10</td><td style="width:133pt">HW0111</td><td style="width:191pt">Washer 1/2 Flat - Zinc</td><td style="width:23pt">10</td></tr><tr style="height:14pt"><td style="width:49pt">11</td><td style="width:133pt">LB0100</td><td style="width:191pt">Nut- Lock - Cone 1/2" x 13</td><td style="width:23pt">5</td></tr><tr style="height:14pt"><td style="width:49pt">12</td><td style="width:133pt">00196411</td><td style="width:191pt">Label Danger - Insure Engagement</td><td style="width:23pt">2</td></tr><tr style="height:13pt"><td style="width:49pt">13</td><td style="width:133pt">00196703</td><td style="width:191pt">Label - Capacity 6000 Lbs.</td><td style="width:23pt">2</td></tr><tr style="height:14pt"><td style="width:49pt">14</td><td style="width:133pt">LB0070</td><td style="width:191pt">Screw Wood #10 x 2 FHWS</td><td style="width:23pt">12</td></tr><tr style="height:14pt"><td style="width:49pt">15</td><td style="width:133pt">LB0130</td><td style="width:191pt">Tag Serial # - BLB-6000</td><td style="width:23pt">1</td></tr><tr style="height:13pt"><td style="width:49pt">16</td><td style="width:133pt">LB-Inspection Label</td><td style="width:191pt">Label - Caution - Inspection - BLB-6000</td><td style="width:23pt">1</td></tr><tr style="height:14pt"><td style="width:49pt">17</td><td style="width:133pt">00196213</td><td style="width:191pt">Warning Label</td><td style="width:23pt">1</td></tr><tr style="height:13pt"><td style="width:49pt"> </td><td style="width:133pt">SP-2400</td><td style="width:191pt">Parts & Service Instructions</td><td style="width:23pt">1</td></tr></table>

=== LOAD CAPACITY STATEMENT MODEL BLB-6000 BATTERY LIFTING BEAM AND BUILT TO STANDARDS ===

'''LOAD CAPACITY STATEMENT MODEL BLB-6OOO'''

'''BATTERY LIFTING BEAM'''

The battery lifting beam model number BLB-6000 has a stated load capacity of 6000# (six thousand). It is designed and tested to meet or exceed any governing rules and regulations pertaining to sufficient factors of safety as well as safety features when used according to its original intent.

Any misuse, abuse or modification to said unit voids all factory warranties. As with any lifting device, units should be visually inspected before each use for any signs of damage or wear.

'''Built To Standards'''

The BLB-6000 was designed and built to current industry and government standards and guidelines. For more information see the following.
<ul>
<li>American National Standards Institute (ASME) B30.20</li>
<li>American National Standards Institute (ASME) B30.20</li>
<li>Occupational Safety and Health ACT (OSHA) (Standards 29 CFR)</li>
</ul>

==STATEMENT OF WARRANTY==

'''Statement of Warranty'''

[https://store.bhs1.com/warranty Click here] for details on BHS' Statement of Warranty.

IOSM-240 BLB

2022-11-17T17:04:48Z

Mbowen: /* STATEMENT OF WARRANTY */

{{DISPLAYTITLE:{{FULLPAGENAME}}}}'''Looking for a specific replacement part?''' Ctrl-F (or Command-F for Mac users) brings up your browsers search panel and can search any text on the entire web page. Find parts by searching a part# or part description.

'''Register your equipment with [https://na.bhs1.com/media-library/bhs-optima/ BHS Optima], BHS's free app.'''

'''California Residents''': WARNING: This product contains chemicals known to the State of California to cause cancer and/or reproductive harm, and birth defects or other reproductive harm. [https://na.bhs1.com/about-bhs/compliance-statement-for-california-proposition-65/ Learn more here.]

== Battery Lifting Beam (BLB) System Parts & Service Manual ==
===SAFETY ===
[[File:IOSM-240-BLB-(03-06-07)-2.jpg|700px|border]]

=== GENERAL SAFETY PRACTICES WHEN HANDLING SUSPENDED LOADS ===
[[File:IOSM-240-BLB-(03-06-07)-3.jpg|500px|right]]
'''GENERAL SAFETY PRACTICES WHEN HANDUNG SUSPENDED LOADS'''

<ol>

<li>Always lock your elbow and stay at least an arm's length away from the load.</li>
<li>Position hand at rear of lifting beam to help guide battery.</li>
<li>Never use your body or limbs to stop a swinging load.</li>
<li>Be sure feet are not under the battery and are out of the primary danger zone.</li>
<li>The operator, as required by your company's safety policy and/or O.S.H.A, '''SHALL''' wear the proper safety equipment.</li>
<li>All lifting apparatus '''SHALL''' be inspected at the begin ning of each shift to ensure no damage or defects are present that could pose a safety hazard.</li>
<li>Areas of travel '''SHALL''' be clear of any trip hazards and obstacles.</li>
<li>Only trained and authorized personnel '''SHALL''' operate overhead lifting equipment and this battery below-the- hook device.</li>
<li>The operator '''SHALL''' verity that any load slings or below-the-hook devices are properly secured to the load prior to lifting or moving the load.</li>
<li>No other persons '''SHALL''' be in the work area or travel path of the load or empty below-the-hook device.</li>
<li>The operator '''SHALL NOT''' place hands or fingers on hooks.</li>
<li>The operator '''SHALL NOT''' tilt the below-the-hook device causing the hooks to hang outside the lines of the below-the-hook device.</li>
</ol>

=== BATTERY LIFTING BEAM DAILY INSPECTION ===
[[File:IOSM-240-BLB-(03-06-07)-4.jpg|700px|border]]

'''BATTERY LIFTING BEAM DAILY INSPECTION'''

Inspections are to be performed: " At the beginning of each shift and/or before first use." Using a lifting device that is worn or damaged can cause loss of load and possible per sonal injury or death.
<ol>
<li>Inspect the wood laminate load members for any cracks, splits, indentions, or delamination.</li>
<li>Inspect all attaching hardware for tightness and wear.</li>
<li>Inspect hook adjusting trunnions for wear or damage.</li>
<li>Inspect load pins on battery lift hooks for wear or damage.</li>
<li>Inspect battery hook engaging throat for excessive wear or damage.
::-Minimum throat height - 5/8" at center of throat.</li>
<li>Inspect lift "A" plate for excessive wear.
::-Minimum height - 3/4" at engagement point to hoist.</li>
</ol>
'''If any of the above conditions do not meet wear and/or dimensional specifications, this device should be removed from service and replaced immediately.'''

=== PROPER HOOK ENGAGEMENT OPERATION ===

'''PROPER HOOK ENGAGEMENT OPERATION'''

Lower the lifting beam horizontally until the hooks are slightly above the battery eyele ts.

Push the beam forward a few inches to allow the hook farthest from you to pass the outside edge of the battery eyelet.

Lower the beam until the hook inserts into the eyelet.

Push down slightly on the heal of the beam closest to you and lower it until the hook can be inserted into the battery eyelet closest to you .

Lift the beam slightly to engage the hooks complete ly in the eyelets of the battery.

Insure both hooks are fully engaged in the battery eyelet.

Continue to lift and move battery

=== PROPER HOOK POSITION FOR THE BHS BLB-6000 BATTERY LIFTING BEAM ===
[[File:IOSM-240-BLB-(03-06-07)-6.jpg|500px|none]]
'''PROPER HOOK POSITION FOR THE BHS BLB-6000 BATTERY LIFTING BEAM'''
'''BASIC OPERATION NOTES'''

Make sure hooks are fully engaged in battery lifting eyelet prior to lifting the battery. Hooks '''SHALL''' be fully inserted into the battery holes as shown in Figure #1

Hooks '''SHALL''' be spaced equally around the center line of the below-the-hook device and be properly placed in the scalloped adjusting trunnions. Correct positioning of the hooks will allow the battery to be level when lifted.

Hooks '''SHALL''' be hanging in a vertical position as shown in Figure #1. Do not allow hooks to be tilted inward or outward as in Figures #2 and #3.

=== PRIMARY DANGER ZONES FOR OPERATORS USING BLB-6000 LIFTING BEAM AND GANTRY CRANE ===
[[File:IOSM-240-BLB-(03-06-07)-7.jpg|700px|border]]

=== BLB-6000 ===
[[File:IOSM-240-BLB-(03-06-07)-4.jpg|700px|border]]

'''BLB-6000'''

 

<table style="border-collapse:collapse;margin-left:92.8407pt" cellspacing="0"><tr style="height:19pt"><td style="width:49pt">Item</td><td style="width:133pt">PPart No.</td><td style="width:191pt">Description</td><td style="width:23pt">Qty</td></tr><tr style="height:20pt"><td style="width:49pt">1</td><td style="width:133pt">24016003</td><td style="width:191pt">Wood BLB-6000 Beam</td><td style="width:23pt">2</td></tr><tr style="height:13pt"><td style="width:49pt">2</td><td style="width:133pt">24015001</td><td style="width:191pt">Hook Standard</td><td style="width:23pt">2</td></tr><tr style="height:13pt"><td style="width:49pt">3</td><td style="width:133pt">24016001</td><td style="width:191pt">Lift Plate - Hook</td><td style="width:23pt">1</td></tr><tr style="height:14pt"><td style="width:49pt">4</td><td style="width:133pt">24017002</td><td style="width:191pt">Plate Spanner</td><td style="width:23pt">2</td></tr><tr style="height:15pt"><td style="width:49pt">5</td><td style="width:133pt">24017005</td><td style="width:191pt">Spacer - Block</td><td style="width:23pt">2</td></tr><tr style="height:14pt"><td style="width:49pt">6</td><td style="width:133pt">24096001</td><td style="width:191pt">Trunnion - Aluminum</td><td style="width:23pt">4</td></tr><tr style="height:14pt"><td style="width:49pt">7</td><td style="width:133pt">LB0080</td><td style="width:191pt">Pin - Spring 1/4" x 1 1/2"</td><td style="width:23pt">8</td></tr><tr style="height:14pt"><td style="width:49pt">8</td><td style="width:133pt">LB0060</td><td style="width:191pt">Straps - Tie</td><td style="width:23pt">4</td></tr><tr style="height:14pt"><td style="width:49pt">9</td><td style="width:133pt">LB0090</td><td style="width:191pt">Bolt 1/2 x 5 NCGR5</td><td style="width:23pt">5</td></tr><tr style="height:13pt"><td style="width:49pt">10</td><td style="width:133pt">HW0111</td><td style="width:191pt">Washer 1/2 Flat - Zinc</td><td style="width:23pt">10</td></tr><tr style="height:14pt"><td style="width:49pt">11</td><td style="width:133pt">LB0100</td><td style="width:191pt">Nut- Lock - Cone 1/2" x 13</td><td style="width:23pt">5</td></tr><tr style="height:14pt"><td style="width:49pt">12</td><td style="width:133pt">00196411</td><td style="width:191pt">Label Danger - Insure Engagement</td><td style="width:23pt">2</td></tr><tr style="height:13pt"><td style="width:49pt">13</td><td style="width:133pt">00196703</td><td style="width:191pt">Label - Capacity 6000 Lbs.</td><td style="width:23pt">2</td></tr><tr style="height:14pt"><td style="width:49pt">14</td><td style="width:133pt">LB0070</td><td style="width:191pt">Screw Wood #10 x 2 FHWS</td><td style="width:23pt">12</td></tr><tr style="height:14pt"><td style="width:49pt">15</td><td style="width:133pt">LB0130</td><td style="width:191pt">Tag Serial # - BLB-6000</td><td style="width:23pt">1</td></tr><tr style="height:13pt"><td style="width:49pt">16</td><td style="width:133pt">LB-Inspection Label</td><td style="width:191pt">Label - Caution - Inspection - BLB-6000</td><td style="width:23pt">1</td></tr><tr style="height:14pt"><td style="width:49pt">17</td><td style="width:133pt">00196213</td><td style="width:191pt">Warning Label</td><td style="width:23pt">1</td></tr><tr style="height:13pt"><td style="width:49pt"> </td><td style="width:133pt">SP-2400</td><td style="width:191pt">Parts & Service Instructions</td><td style="width:23pt">1</td></tr></table>

=== LOAD CAPACITY STATMENT MODEL BLB-6000 BATTERY LIFTING BEAM AND BUILT TO STANDARDS ===

'''LOAD CAPACITY STATEMENT MODEL BLB-6OOO'''

'''BATTERY LIFTING BEAM'''

The battery lifting beam model number BLB-6000 has a stated load capacity of 6000# (six thousand). It is designed and tested to meet or exceed any governing rules and regulations pertaining to sufficient factors of safety as well as safety features when used according to its original intent.

Any misuse, abuse or modification to said unit voids all factory warranties. As with any lifting device, units should be visually inspected before each use for any signs of damage or wear.

'''Built To Standards Standards'''

The BLB-6000 was designed and built to current industry and government standards and guidelines. For more information see the following.
<ul>
<li>American National Standards Institute (ASME) B30.20</li>
<li>American National Standards Institute (ASME) B30.20</li>
<li>Occupational Safety and Health ACT (OSHA) (Standards 29 CFR)</li>
</ul>

==STATEMENT OF WARRANTY==

'''Statement of Warranty'''

[https://store.bhs1.com/warranty Click here] for details on BHS' Statement of Warranty.